LG 20M35D, 24M35D, 24M35A, 22M35A, 22M35D User Manual

ENGLISH

OWNER’S MANUAL

LED LCD MONITOR

Please read this manual carefully before operating your set and retain it for future reference.

LED LCD MONITOR MODEL

19M35A 19M35D 20M35A 20M35D 22M35A 22M35D 24M35A 24M35D

www.lg.com

WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.

ENGLISH

2 TABLE OF CONTENTS

CONTENTS

	3	ASSEMBLING AND PREPAR-		22	TROUBLESHOOTING
		ING		24
	3	Unpacking			SPECIFICATIONS‌
	4	Parts and buttons
			24		19M35A
	5	Moving and Lifting the Monitor
	6	Setting up the Monitor set	25		19M35D
	6	- Attaching the Stand Base	26		20M35A
	6	- Detaching the Stand Base	28		20M35D
	7	- Mounting on a table	30		22M35A
	7	- Using the cable holder	31		22M35D
	9	- Mounting on a wall	32		24M35A
			33		24M35D
	10	USING THE MONITOR SET	34		Preset Modes (Resolution)
			35		Indicator
	10 Connecting to a PC
	10	- D-SUB connection		36	PROPER POSTURE
	10	- DVI-D connection
			36		Proper posture for using the Monitor set.

12 CUSTOMIZING SETTINGS

13Customizing Settings

13- Menu Settings

14-Picture

15-Color

16-Display

17-Others

18READER Setting

19FUNC. Setting

19-SUPER ENERGY SAVING

20-Picture Mode

21-DUAL DISPLAY

21 -DUAL WEB

ASSEMBLING AND PREPARING 3

ASSEMBLING AND PREPARING

Unpacking

Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and accessories.

ENGLISH

CD(Owner's Manual) /	D-SUB Cable
Card

Power Cord AC-DC Adapter

( Depending on the country )

DVI-D Cable

(This cable is not included in all countries.)

(19M35D,20M35D,22M35D,24M35D)

or

AC-DC Adapter

( Depending on the country )

Stand Body

Stand Base

Cable holder

CAUTION

yyDo not use any unapproved accessories to ensure the safety and product life span.

yyAny damages or injuries by using unapproved accessories are not covered by the warranty.

NOTE

yyThe accessories supplied with your product may vary depending on the model.

yyProduct specifications or contents in this manual may be changed without prior notice due to upgrade of product functions.

4 ASSEMBLING AND PREPARING

Parts and buttons

ENGLISH

Power Indicator yyLighting On: Turned on yyLighting Off: Turned off

(Power Button)

Button (See p.12)

Connection panel (See p.10)

	ASSEMBLING AND PREPARING 5
Moving and Lifting the Monitor	yyWhen holding the monitor, the screen should
When moving or lifting the monitor, follow these	face away from you to prevent it being
instructions to prevent the monitor from being	scratched.
scratched or damaged and to ensure safe trans-
portation regardless of its shape or size.
yyIt is advisable to place the monitor in the
original box or packing material before at-
tempting to move it.
yyBefore moving or lifting the monitor, discon-
nect the power cord and all cables.
yyHold the top and bottom of the monitor frame	yyWhen moving the monitor, avoid any strong
firmly. Do not hold the panel itself.	shock or vibrations to the product.
	yyWhen moving the monitor, keep it upright,
	never turn the monitor on its side or tilt it
	sideways.

CAUTION

yyAs far as possible, avoid touching the monitor screen. This may result in damage to the screen or some of the pixels used to create images.

ENGLISH

6 ASSEMBLING AND PREPARING

ENGLISH

Setting up the Monitor set

Attaching the Stand Base

1Place the Monitor set with the screen side down on a flat and cushioned surface.

CAUTION

Lay a foam mat or soft protective cloth on the surface to protect the screen from damage.

21 Attach the Stand Body to the monitor set.

2 Attach the Stand Base.

3 Tighten the screw to the right.

Stand Body

Stand Base

Detaching the Stand Base

1Place the Monitor set with the screen side down on a flat and cushioned surface.

21 Pull out the Stand Body and Stand Base from the monitor set.

2Turn the screw to the left.

3Pull out the Stand Base.

Stand Body

Stand Base

Stand Body

Stand Base

	ASSEMBLING AND PREPARING 7
Mounting on a table	3 Press (Power) button on the bottom switch
	panel to turn the power on.
1 Lift and tilt the Monitor set into its upright
position on a table.
Leave a 10 cm (minimum) space from the wall
for proper ventilation.	CAUTION

10 cm

10 cm

10 cm

10 cm

Unplug the power cord before moving the Monitor to another location. Otherwise electric shock may occur.

Using the cable holder

ENGLISH

2Connect the AC-DC Adapter and Power Cord to a wall outlet.

or

Cable holder

ENGLISH

8 ASSEMBLING AND PREPARING

WARNING

Using the Kensington security system

When you adjust the angle, do not hold the bottom of the Monitor set frame as shown on the following illustration, as may injure your fingers.

Do

Do not hold this set like below picture.Monitor screen can detach from stand base and injure your body.

NOTE

+20 to -3			up or down to adjust
the angle of the Monitor			to suit your view.

The Kensington security system connector is located at the back of the Monitor set. For more information of installation and using, refer to the manual supplied with the Kensington security system or visit http://www.kensington.com.

Connect the Kensington security system cable between the Monitor set and a table.

NOTE

The Kensington security system is optional. You can obtain it from most electronics stores.

Front

Rear

ASSEMBLING AND PREPARING 9

Mounting on a wall

For proper ventilation, allow a clearance of 10 cm on each side and from the wall. Detailed instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and Setup Guide.

10 cm

10 cm

10 cm

10 cm

If you intend to mount the Monitor set to a wall, attach Wall mounting interface (optional parts) to the back of the set.

When you install the Monitor set using a wall mounting interface (optional parts), attach it carefully so it will not drop.

1Please, Use the screw and wall mount interface in accordance with VESA Standards.

2If you use screw longer than standard, the monitor might be damaged internally.

3If you use improper screw, the product might be damaged and drop from mounted position. In

this case, LG Electronics is not responsible for it.

4VESA compatible only with respect to screw mounting interface dimensions and mounting

screw specifications.

5 Please use VESA standard as below. yy784.8 mm (30.9 inch) and under

*Wall Mount Pad Thickness : 2.6 mm

* Screw : Φ 4.0 mm x Pitch 0.7 mm x

Length 10 mm

yy787.4 mm (31.0 inch) and above

*Please use VESA standard wall mount pad and screws.

Model
		19M35A	19M35D			24M35A
		20M35A 20M35D
						24M35D
		22M35A 22M35D
								ENGLISH
VESA (A x B)		75 x 75				100 x 100
Standard		M4				M4
screw
Number of	4				4
screws

CAUTION

yyDisconnect the power cord first, and then move or install the Monitor set. Otherwise electric shock may occur.

yyIf you install the Monitor set on a ceiling or slanted wall, it may fall and result in severe injury.

yyUse only an authorized LG wall mount and contact the local dealer or qualified personnel.

yyDo not over tighten the screws as this may cause damage to the Monitor set and void your warranty.

yyUse only screws and wall mounts that meet the VESA standard. Any damages or injuries by misuse or using an improper

accessory are not covered by the warranty. yyScrew length from outer surface of back

cover should be under 8mm. Wall mount Pad

Back Cover

Wall mount Pad

Back Cover

Standard screw

Max.8mm

NOTE

yyUse the screws that are listed on the VESA standard screw specifications.

yyThe wall mount kit will include an installation manual and necessary parts.

yyThe wall mount bracket is optional. You can obtain additional accessories from your local dealer.

yyThe length of screws may differ depending on the wall mount. Be sure to use the proper length.

yyFor more information, refer to the instructions supplied with the wall mount.

ENGLISH

10 USING THE MONITOR SET

USING THE MONITOR SET

Connecting to a PC

yyYour Monitor set supports Plug & Play*.

*Plug & Play: A PC recognizes a connected device that users connect to a PC and turn on, without device configuration or user intervention.

D-SUB connection

Transmits analog video from your PC to the Monitor set. Connect the PC and the Monitor set with the supplied D-sub 15 pin signal cable as shown in the following illustrations.

NOTE

yyWhen using a D-Sub signal input cable connector for Macintosh

yyMac adapter

For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-SUB VGA connector on the supplied cable to a 15 pin 2 row connector.

DVI-D connection

Transmits a digital video signal from your PC to the Monitor set. Connect the PC and the Monitor set with a DVI cable as shown in the following illustrations.

USING THE MONITOR SET 11

	CAUTION	Self Image Setting Function
		Press the power button on the bottom panel to

yyConnect the signal input cable and tighten

it by turning the screws clockwise.

yyDo not press the screen with your finger for a long time as this may result in temporary distortion on the screen.

yyAvoid displaying a fixed image on the screen for a long period of time to prevent image burn. Use a screensaver if possible.

turn the power on. When monitor power is turned on, the "Self Image Setting" Function is executed automatically. (Only supported in Analog Mode)

ENGLISH

NOTE

yyWhen you want to use two PC in our Monitor, please connect the signal cable(D-SUB/ DVI-D) respectively in Monitor set.

yyIf you turn the Monitor set on while it is cold, the screen may flicker. This is normal.

yySome red, green, or blue spots may appear on the screen. This is normal.

NOTE

yy"Self Image Setting" Function.

This function provides the user with optimal display settings.When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals.(Only supported in Analog Mode)

yy‘AUTO’ Function.

When you encounter problems such as blurry screen, blurred letters, screen flicker or tilted screen while using the device or after changing screen resolution, press the AUTO function button to improve resolution. (Only supported in Analog Mode)