110.4770*
Table of contents
Loading...Kenmore 110.4770*, 110.4771*, 110.4775*, 110.4776*, 110.4778* Owner's Manual
...
®
Front-Loading Automatic Washer
Use & Care Guide
Lavadora automática de carga frontal
Manual de uso y cuidado
Laveuse automatique à chargement frontal
Guide d’utilisation et d’entretien
Models/Modelos/Modèles 110.4770∗, 4771∗, 4775∗, 4776∗, 4778∗ , 4779∗
∗ = color number, número de color, numéro de couleur
Designed to use only HE High
Efficiency detergent
Diseñado para utilizar solamente
detergente de alto rendimiento
Conçu pour l’utilisation d’un
détergent haute efficacité
seulement
Certified to Sanitize
Certificado para higienizar
Certifié pour aseptiser
W10176967B Sears Canada Inc., Toronto, Ontario, Canada M5B 2B8 www.sears.ca
Sears Roebuck and Co., Hoffman Estates, IL 60179, U.S.A. www.sears.com
TABLE OF CONTENTS
PROTECTION AGREEMENTS
PROTECTION AGREEMENTS.......................................................2
WARRANTY.....................................................................................3
WASHER SAFETY ..........................................................................4
INSTALLATION REQUIREMENTS ................................................5
Tools and Parts ............................................................................5
Options .........................................................................................5
Location Requirements ................................................................5
Drain System ................................................................................7
Electrical Requirements................................................................7
INSTALLATION INSTRUCTIONS ..................................................8
Remove Transport System...........................................................8
Connect the Inlet Hoses...............................................................9
Route the Drain Hose ...................................................................9
Secure the Drain Hose .................................................................9
Level the Washer....................................................................... 10
Complete Installation................................................................. 10
FEATURES AND BENEFITS ....................................................... 10
WASHER USE .............................................................................. 12
Starting Your Washer ................................................................ 12
Using the Proper Detergent ...................................................... 12
Using the Dispenser .................................................................. 13
Pausing or Restarting................................................................ 14
Changing Cycles, Options, and Modifiers ................................ 14
Status Lights.............................................................................. 15
Cycles ........................................................................................ 16
Normal Washer Sounds ............................................................ 17
Options ...................................................................................... 17
Modifiers.................................................................................... 18
Laundry Guide ........................................................................... 19
LAUNDRY TIPS............................................................................ 20
Loading...................................................................................... 20
WASHER CARE ........................................................................... 21
Cleaning Your Washer............................................................... 21
Water Inlet Hoses ...................................................................... 22
Vacation, Storage, and Moving Care........................................ 22
TROUBLESHOOTING.................................................................. 23
SERVICE NUMBERS ............................................... BACK COVER
Master Protection Agreements
Congratulations on making a smart purchase. Your n e w
Kenmore
dependable operation. But like all products, it may require
preventive maintenance or repair from time to time. That’s when
having a Master Protection Agreement can save you money and
aggravation.
The Master Protection Agreement also helps extend the life of
your new product. Here’s what the Agreement* includes:
®
product is designed and manufactured for years of
✓ Parts and labor needed to help keep products operating
properly under normal use, not just defects. Our coverage
goes well beyond the product warranty. No deductibles, no
functional failure excluded from coverage—real protection.
✓ Expert service by a force of more than 10,000 authorized
Sears service technicians, which means someone you can
trust will be working on your product.
✓ Unlimited service calls and nationwide service, as often as
you want us, whenever you want us.
✓ “No-lemon” guarantee – replacement of your covered
product if four or more product failures occur within twelve
months.
✓ Product replacement if your covered product can’t be fixed.
✓ Annual Preventive Maintenance Check at your request – no
extra charge.
✓ Fast help by phone – we call it Rapid Resolution – phone
support from a Sears representative on all products. Think of
us as a “talking owner’s manual.”
✓ Power surge protection against electrical damage due to
power fluctuations.
✓ $250 Food Loss Protection annually for any food spoilage
that is the result of mechanical failure of any covered
refrigerator or freezer.
✓ Rental reimbursement if repair of your covered product
takes longer than promised.
✓ 10% discount off the regular price of any non-covered repair
service and related installed parts.
Once you purchase the Agreement, a simple phone call is all that
it takes for you to schedule service. You can call anytime day or
night, or schedule a service appointment online.
The Master Protection Agreement is a risk free purchase. If you
cancel for any reason during the product warranty period, we will
provide a full refund. Or, a prorated refund anytime after the
product warranty period expires. Purchase your Master
Protection Agreement today!
Some limitations and exclusions apply. For prices and
additional information in the U.S.A. call 18008276655.
*Coverage in Canada varies on some items. For full details
call Sears Canada at 18003616665.
Sears Installation Service
For Sears professional installation of home appliances, garage
door openers, water heaters, and other major home items, in the
U.S.A. or Canada call 18004MYHOME
®
.
2
KENMORE ELITE® APPLIANCE WARRANTY
ONE YEAR LIMITED WARRANTY
When installed, operated and maintained according to all
instructions supplied with the product, if this appliance fails due
to a defect in material or workmanship within one year from the
date of purchase, call 1-800-4-MY-HOME
repair.
LIMITED LIFETIME WARRANTY ON STAINLESS
DRUM
STEEL
For the lifetime of the washer from the date of purchase, when
this washer is installed, operated and maintained according to all
instructions supplied with the product, Sears will replace the
stainless steel wash drum due to defective materials or
workmanship. After the first year, customer assumes any labor
costs associated with replacement of this part.
TEN YEAR LIMITED WARRANTY ON PLASTIC TUB
For ten years from the date of purchase, when this washer is
installed, operated and maintained according to all instructions
supplied with the product, Sears will replace the plastic tub due
to defective materials or workmanship. After the first year,
customer assumes any labor costs associated with replacement
of this part.
FIVE YEAR LIMITED WARRANTY ON DRIVE SYSTEM PARTS
For five years from the date of purchase, when this washer is
installed, operated and maintained according to all instructions
supplied with the product, Sears will replace the following drive
system parts if defective in materials or workmanship: drive
pulley and drive belt. After the first year, customer assumes any
labor costs associated with replacement of these parts.
TWO YEAR LIMITED WARRANTY ON SENSOR SMART™
ELECTRONIC BOARD
For two years from the date of purchase, when this washer is
installed, operated and maintained according to all instructions
supplied with the product, Sears will replace the electronic
control board if defective in materials or workmanship. After the
first year, customer assumes any labor costs associated with
replacement of these parts.
If this appliance is used for other than private family purposes,
this warranty applies for only 90 days from the date of purchase.
THIS WARRANTY COVERS ONLY DEFECTS IN MATERIAL
AND WORKMANSHIP. SEARS WILL NOT PAY FOR:
1. Expendable items that can wear out from normal use,
including but not limited to filters, belts, light bulbs, and bags.
2. A service technician to instruct the user in correct product
installation, operation or maintenance.
3. A service technician to clean or maintain this product.
®
to arrange for free
4. Damage to or failure of this product if it is not installed,
operated or maintained according to all instructions supplied
with the product.
5. Damage to or failure of this product resulting from accident,
abuse, misuse or use for other than its intended purpose.
6. Damage to or failure of this product caused by the use of
detergents, cleaners, chemicals or utensils other than those
recommended in all instructions supplied with the product.
7. Damage to or failure of parts or systems resulting from
unauthorized modifications made to this product.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF
REMEDIES
Customer’s sole and exclusive remedy under this limited
warranty shall be product repair as provided herein. Implied
warranties, including warranties of merchantability or fitness for a
particular purpose, are limited to one year or the shortest period
allowed by law. Sears shall not be liable for incidental or
consequential damages. Some states and provinces do not allow
the exclusion or limitation of incidental or consequential
damages, or limitations on the duration of implied warranties of
merchantability or fitness, so these exclusions or limitations may
not apply to you.
This warranty applies only while this appliance is used in the
United States and Canada.
This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
Sears, Roebuck and Co.
Dept. 817WA, Hoffman Estates, IL 60179
Sears Canada Inc.
Toronto, Ontario, Canada M5B 2B8
PRODUCT RECORD
In the space below, record your complete model number, serial
number, and purchase date. You can find this information on the
model and serial number label located on the product.
Have this information available to help you obtain assistance or
service more quickly whenever you contact Sears concerning
your appliance.
Model number __ __ __. __________________________________________
Serial number___________________________________________________
Purchase date __________________________________________________
Save these instructions and your sales receipt for future
reference.
3
WASHER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
You can be killed or seriously injured if you don't immediately
DANGER
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
follow instructions.
can be killed or seriously injured if you don't
You
instructions.
follow
4
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation.
The parts supplied are in the washer drum.
Tools needed for connecting the water inlet hoses
■ Pliers (that open to 1 ■ Flashlight (optional)
Tools needed for installation
■ Open end wrenches 17 mm and 13 mm ■ Level ■ Wood block
Ruler or measuring tape
Parts supplied:
A B
DE
Alternate Parts
Parts listed are available from your local Sears store or Sears
Service Center. For further information, please call
1-800-4-MY-HOME® (1-800-469-4663).
If You Have You Will Need to Buy
Laundry tub or
standpipe taller
an 96" (2.4 m)
th
Overhead sewer Standard 20 gal. (76 L), 30" (762 mm) tall
Floor drain Siphon break, Part Number 285834;
Drain hose
too short
Water faucets
be
yond reach
of fill hoses
9
/16" [39.5 mm])
C
A. Drain hose form
B. Inlet hose (2)
C. Inlet hose washers (4)
D. Transport bolt hole plug (4)
E. Beaded strap
Sump pump system (if not already
available)
drai
n tub or utility sink and sump pump
(available from local plumbing suppliers)
itional drain hose, Part
add
Number 8318155; and connector kit,
Part Number 285835
4 ft (1.2 m) drain hose extension kit,
Part Number 285863
2 longer water fill hoses:
6 ft (1.8 m) Part Number 76314,
10 ft (3.0 m) Part Number 350008
Options
Pedestal
You have the option of purchasing pedestals of different heights
separately for this washer. You may select a 10" (254 mm) or a
394 mm) pedestal. The pedestal will add to the total height
15.5" (
of the washer.
This pedestal (with storage drawer) is available in several colors.
To order, call your local Sears stor
please call 1-800-4-MY-HOME
Pedestal
Height
10" (254 mm) White 46822
15.5" (394 mm) White 57822
15.5" (394 mm) Barolo 58829
15.5" (394 mm) Twilight 58827
15.5" (394 mm) Truffle 58828
15.5" (394 mm) Chai 58821
AB
A. 10" (254 mm) pedestal
B. 15.5" (394 mm) pedestal
Color Part Number
e. For further information,
®
(1-800-469-4663).
Stack Kit
Are you planning to stack your Kenmore washer and dryer?
To do so, find the stack kit (8541503) in the drum of the matching
more dryer. Follow instructions included with the kit. See
Ken
“Location Requirements.”
Location Requirements
Selecting the proper location for your washer improves
performance and minimizes noise and possible washer “walk.”
Your washer can be installed under a custom counter, or in a
ba
sement, laundry room, closet, or recessed area. See “Drain
System.”
Companion appliance location req
considered. Proper installation is your responsibility.
You will need
■
A water heater set to deliver 120°F (49°C) water to the washer.
■
A grounded electrical outlet located within 6 ft (1.8 m) of where the power cord is attached to the back of the washer. See “Electrical Requirements.”
uirements should also be
5
■
Hot and cold water faucets located within 4 ft (1.2 m) of the hot and cold water fill valves, and water pressure of 20-100 psi (137.9-689.6 kPa).
■
If you live in a hard water area, use of a water softener is
recommended to control the buildup of scale in the steamer and
other areas of the washer. Over time, the buildup of lime scale
may clog the steamer, which will reduce steamer efficiency and
performance. Excessive buildup of scale may lead to the need
for steamer replacement or repair.
■
A level floor with a maximum slope of 1" (25 mm) under entire washer. Installing the washer on soft floor surfaces, such as carpets or surfaces with foam backing, is not recommended.
■
A sturdy and solid floor to support the washer with a total weight (water and load) of 400 lbs (180 kg).
Do not operate your washer in temperatures below 32°F (0°C).
Some water can remain in the washer and can cause damage
in low temperatures.
Installation clearances
■
The location must be large enough to allow the washer door to be fully opened.
■
Additional spacing should be considered for ease of installation and servicing.
■
Additional clearances might be required for wall, door, and floor moldings.
■
Additional spacing of 1" (25 mm) on all sides of the washer is recommended to reduce noise transfer.
■
Companion appliance spacing should also be considered.
Recommended installation spacing for recessed or closet installation, with or without a pedestal
The dimensions shown are for the recommended spacing.
Recessed area or closet installation
3"
18" min.
(457 mm)
(76 mm)
3"
(76 mm)
2
*
34"
(864 mm)
1"
31½"
(25 mm)
(800 mm)
A
(310 cm2)
(155 cm2)
4"
(102 mm)
48 in.
24 in.
2
*
B
A. Side view - closet or confined area
B. Closet door with vents
*Min. top and bottom air openings for closet door.
Recessed or closet installation - Washer on pedestal
Washer Dimensions
27"
51"
(1295 mm)
(686 mm)
31½"
(800 mm)
38"
(965 mm)
Recommended installation spacing for custom undercounter installation
The dimensions shown are for the recommended spacing.
Custom undercounter installation - Washer only
39" min.
(990 mm)
1"
(25 mm)
27"
(686 mm)
1"
(25 mm)
1"
(25 mm)
31½"
(800 mm)
4"
(102 mm)
A B
A. Recessed area
B. Side view - closet or confined area
Recommended installation spacing for recessed or closet installation, with stacked washer and dryer
The dimensions shown are for the recommended spacing.
48 in.2 *
(310 cm2)
3"* (76 mm)
1"
(25 mm
)
27"
(686 mm)
1"
(25 mm)
(155 cm2)
quired spacing
*Re
24 in.
3"* (76 mm)
2
*
1"* (25 mm)
6
6"* (152 mm)
76"
(1930 mm)
30" min.
(762 mm)
5½"**
(140 mm)
1"
(25 mm)
27"
(686 mm)
1"
(25 mm)
*Required spacing
**For venting out the side, 1" (25 mm) spacing is allowed.
Recommended installation spacing for cabinet installation
■ The dimensions shown are for the recommended spacing. ■ For cabinet installation, with a door, the minimum ventilation
openings in the top are required.
7" (178 mm)
7" (178 mm)
9"
(229 mm)
A
B
Laundry tub drain system (view C)
The laundry tub needs a minimum 20 gal. (76 L) capacity. The top
of the laundry tub must be at least 30" (762 mm) above the floor.
Floor drain system (view D)
The floor drain system requires a siphon break that may be
purchased separately. See “Tools and Parts.”
The siphon break must be a minimum of 28" (711 mm) from the
bottom of the washer
. Additional hoses might be needed.
28" min.
30" min.
(762 mm)
(711 mm)
CD
Electrical Requirements
WARNING
4"
(102 mm)
31½"
(800 mm)
1"
(25 mm)1"(25 mm)
27"
(686 mm)
1"
(25 mm)
Drain System
The washer can be installed using the standpipe drain system
(floor or wall), the laundry tub drain system, or the floor drain
system. Select the drain hose installation method you need.
See “Tools and Parts.”
Standpipe drain system - wall or floor (views A & B)
The standpipe drain requires a minimum diameter standpipe of
2" (50 mm). The minimum carry-away capacity can be no less
than 17 gal. (64 L) per minute.
The top of the standpipe must be at least 30" (762 mm) high and
higher than 96" (2.4 m) from the bottom of the washer.
no
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
re, or electrical shock.
■ A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical
supply is required. A time-delay fuse or circuit breaker is
recommended. It is recommended that a separate circuit
serving only this appliance be provided.
■
This washer is equipped with a power supply cord having a 3 prong grounding plug.
7
■
To minimize possible shock hazard, the cord must be plugged
into a mating, grounded 3 prong outlet, grounded in accordance
th local codes and ordinances. If a mating outlet is not
wi
available, it is the personal responsibility and obligation of the
customer to have the properly grounded outlet installed by a
qualified electrician.
■ If codes permit and a separate ground wire is used, it is
recommended that a qualified electrician determine that the
ground path is adequate.
■ Do not ground to a gas pipe. ■ Check with a qualified electrician if you are not sure the
washer is properly grounded.
■ Do not have a fuse in the neutral or ground circuit.
INSTALLATION INSTRUCTIONS
Remove Transport System
WARNING
Excessive Weight Hazard
Use two or more people to move and install washer.
Failure to do so can result in back or other injury.
IMPORTANT: Position the washer so that the rear of the washer
is within approximately 3 ft (900 mm) of its final location.
There are 4 bolts in the rear panel of the washer that support the
suspension system during transportation. These bolts also retain
the power cord inside the washer until the bolts are removed.
1. Using a 13 mm wrench, loosen each of the bolts.
2. Onc
e the bolt is loose, move it to the center of the hole and
completely pull out the bolt, including the plastic spacer
covering the bolt.
3. Once all 4 bolts are removed, discard the bolts and spacers.
Then pull the power cord through the opening of the rear
panel and close the hole with the attached cap.
4. Close t
NOTE:
local service center. To avoid suspension and structural damage to
your washer, it must be properly set up for relocation by a certified
technician.
he bolt holes with the 4 transport bolt hole plugs.
If the washer is to be transported at a later date, call your
8
Connect the Inlet Hoses
1. Insert new flat washers (supplied) into each end of the inlet
hoses. Firmly seat the washers in the couplings.
A B
A. Coupling
B. Washer
2. Make sure the washer drum is empty.
3. Attach th
inlet valve. Attaching the red coupling first makes it easier to
tighten connection with pliers. Screw on coupling by hand
until it is seated on the washer.
4. Attach th
(right) water inlet valve. Screw on coupling by hand until
it is seated on the washer.
e hose with the red color indicator to the Hot (left)
e hose with the blue color indicator to the Cold
Route the Drain Hose
Proper routing of the drain hose protects your floors from damage
due to water leakage. Read and follow these instructions.
Remove drain hose from washer cabinet
Gently pull the corrugated drain hose from the shipping clips.
Laundry tub drain or standpipe drain
Connect the drain hose form to the corrugated d
rain hose.
H
H. Hot water inlet
C. Cold water inlet
5. Using pliers, check the tightness of the hose couplings
already attached to the washer.
NOTE: Do n
can result.
6. Attach hot water hose to the hot water faucet. Screw on
coupling by hand until it is seated on the washer.
7. Atta
8. Using pliers, tigh
ch cold water hose to the cold water faucet. Screw on
coupling by hand until it is seated on the washer.
two-thirds turn.
ot overtighten. Damage to the coupling
ten the couplings with an additional
C
A B
A. Snap either end of the drain hose form to the drain hose
at the point where the corrugation begins.
B. Bend drain hose over
To keep drain water from going back into the washer:
■ Do not straighten the drain hose, and do not force excess
drain hose into standpipe. Hose should be secure, but loose
enough to provide a gap for air.
■ Do not lay excess hose on the bottom of the laundry tub.
drain hose form and snap into place.
Floor drain
You may need additional parts. See Floor drain under “Tools
and Parts.”
Secure the Drain Hose
1. Drape the power cord over the washer top.
2. Secur
e the drain hose to the laundry tub leg or standpipe with
the beaded strap provided. (See illustrations A and B.)
NOTE: Do not overtighten. Damage to the coupling
can result.
9. Turn on the water faucets and check for leaks.
Replace inlet hoses after 5 years of use to reduce the
NOTE:
risk of hose failure. Record hose installation or replacement
dates on the hoses for future reference.
Periodically inspect and replace hos
wear, or leaks are found.
es if bulges, kinks, cuts,
A BC
If the washer faucets and the drain standpipe are recessed
(see illustration C), put the hooked end of the drain hose in
the s
tandpipe. Tightly wrap the beaded strap around the
water inlet hoses and the drain hose.
Do not force excess drain hose into the standpipe.
9
Level the Washer
Properly leveling your washer avoids excessive noise and
vibration.
1. Check the levelness o
top edge of the washer, first side to side, then front to back.
f the washer by placing a level on the
Complete Installation
1. Check the electrical requirements. Be sure that you have the
correct electrical supply and the recommended grounding
method. See “Electrical Requirements.”
e sure all parts are now installed. If there is an extra part, go
2. B
back through the steps to see which step was skipped.
3. Be sur
4. Di
5. Be sure the water faucets are on.
6. Che
e you have all of your tools.
spose of/recycle all packaging materials.
ck for leaks around faucets and inlet hoses.
If the washer is against a wall, move the washer out slightly
before tipping back. If the washer is not level, first prop the
front with a wood block and adjust the feet as necessary;
then prop the back and adjust feet as necessary. Repeat this
step until washer is level.
2. Ma
ke sure that all four feet are stable and resting on the floor.
Then check that the washer is perfectly level (use a level).
3. After
4. Slide
5. Conf
the washer is level, use a 17 mm open-end wrench to
turn the nuts on the feet tightly against the washer cabinet.
IMPORTANT: All four fe
not tight against the washer cabinet, the washer may vibrate.
When you are pushing on the edges of the washing machine
top plate, the machine should not move front to back, side to
side, or diagonally.
the washer to its final location.
irm the levelness of the washer.
et must be tightened. If the nuts are
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
re, or electrical shock.
7. Plug into a grounded 3 prong outlet.
8. Read “Washer Use.”
o test and to clean your washer, measure 1/2 of the
9. T
manufacturer’s recommended amount of powdered or liquid
High Efficiency (HE) detergent for a medium-size load. Pour
the detergent into the detergent dispenser. Select EXPRESS
WASH, and then select START. Allow the washer to complete
one whole cycle.
10
Use only HE High Efficiency detergent.
FEATURES AND BENEFITS
Audio Visual Electronic Controls
Flexible electronic controls are easy to use whether you are a
beginner or an expert.
Detergent Advantage System Dispenser
The Smart Dispensers make your washer truly automatic. This
washer provides a four-compartment dispenser which includes
separate compartments for High Efficiency “HE” detergent, fabric
softener, liquid chlorine bleach and oxygen based stain fighters
or color-safe bleach. The dispenser can easily be removed for
cleaning. Laundry products are dispensed automatically at the
proper time during the wash cycle, making it unnecessary for you
to return to the washer during the cycle to add them and ensuring
that these cleaning products perform their very best.
STEAM TREAT™
This washer has a built-in steaming unit which is combined with
the STEAM TREAT
help remove a variety of stains from garments.
™ option to provide multiple temperatures to
Oxi / Color-safe Bleach Dispenser
With the Oxi / Color-safe bleach dispenser and the TIMED OXI™
option, there is no need to come back and add your oxygen
based stain fighter or your color-safe bleach. The washer will
automatically add these laundry products, to the cycle, at the
appropriate time. Delaying the introduction of these laundry
products helps remove many stains better.
Clean Washer Cycle with STEAMCARE™
This cycle uses steam to raise the temperature of the unit and
makes the washer self-cleaning, flushing the machine’s interior
free of dirt and other residue. The use of liquid chlorine bleach
with this cycle will remove and avoid odor-causing residue.
Auto Water Level
Adjusting to the size of the load, this feature allows the washer to
use the minimal amount of water needed to clean and rinse the
clothes. With a low water level, you can obtain the same results
with smaller amounts of laundry products. Because only the
required amount of water is used, the washer saves energy, too.
Larger Load Size
Since there is no agitator, you can wash larger, bulkier items such
as an average size sleeping bag, pillow, or a king size bedspread.
You are also able to wash more clothes at one time, which means
fewer loads.
Stainless Steel Drum
The stainless steel drum eliminates corrosion and enables higher
spin speeds for more water extraction, helping to reduce drying
time.
High-Efficiency Wash System
Your new front-loading, high-efficiency washer saves time with
fewer, larger loads. It also conserves resources and lowers your
water and energy bills.
Spin Speeds
This washer automatically selects a spin speed based on the
cycle selected. This factory setting can be changed, however,
with up to six different spin speed choices.
Thermal Optimizer with Smart Wash Technology
The heating system ensures that the wash water is heated to the
preset temperature for Normal/Casual, Bulky/Bedding, Kidswear,
Heavy Duty, Whitest Whites, and the STEAM TREAT™ option. It
also provides Smart Wash Technology with “Stepped Cleaning”
when you are using the STEAM TREAT™ option. “Stepped
Cleaning” starts the wash cycle with warm water to remove
stains.
Add Clothes
This option is available in all wash cycles except Rinse & Spin,
Drain & Spin, and Clean Washer. When this option is available
at the beginning of the cycle, the Add Clothes status light
will illuminate for the first 4-8 minutes. This washer allows a
4-8 minute period in which other garments may be added to a
load.
CATALYST® Cleaning Action
A concentrated detergent solution is sprayed onto the clothes
at the beginning of the cycle to ensure that the detergent comes
into contact with the clothes as quickly as possible, helping
to remove stains from your clothes without pretreating.
Dynamic Balance
A precision balancing system that allows the washer to reach
spin speeds of up to 1,100
clothes coming out of the washer will dry faster. In addition, if the
Dynamic Balance system detects off-balance loads during
spinning, it redistributes the clothes so that they are evenly
balanced.
rpm. The washer spins faster so that
Suspension System
To reduce washer “walk” and “off-balance” conditions, your new
washer combines:
■ 2 Springs to isolate vibration ■ 4 Shock absorbers at the washer base to minimize movement
11
WASHER USE
Starting Your Washer
WARNING: To reduce the risk of fire, electric shock, or injury to
persons, read the IMPORTANT SAFETY INSTRUCTIONS before
operating this appliance.
The following is a guide to using your washer. Please refer to
fic sections of this manual for more detailed information.
speci
Do not store laundry products on the top surface of this washer.
ibration is normal during operation.
V
Using the Proper Detergent
Use only High Efficiency detergents. The package for this type of
detergent will be marked “HE” or “High Efficiency.” This wash
system, along with less water, will create too much sudsing with a
regular non-HE detergent. Using regular detergent will likely result
in washer errors, longer cycle times, and reduced rinsing
performance. It may also result in component failures and
noticeable mold or mildew. HE detergents are made to produce
the right amount of suds for the best performance. Follow the
manufacturer’s instructions to determine the amount of detergent
to use. Remember, concentrated detergents such as 2x or higher
will use less detergent based on load size.
First Wash Cycle Without Laundry
Before washing clothes for the first time, if not completed during
the final installation step, choose the Express Wash cycle and run
it without clothes. Use only HE High Efficiency detergent. Use
the manufacturer’s recommended amount for a medium-size
load. This initial cycle serves to ensure the interior is clean before
washing clothes.
1
/2
For All Wash Cycles
1. Open the washer door by pulling on the handle. Sort laundry
according to color and type of fabric. Place a load of sorted
clothes in the washer. Do not overload washer. Overloading
can cause poor cleaning.
■ The washer can be fully loaded, but not tightly packed.
Washer door should close easily.
■ Mix large and small items. Avoid washing a single item.
Load evenly.
■ Wash small items such as infant socks in mesh garment
bags. It is recommended that more than one garment bag
be used and that each garment bag be filled with equal
amounts of material.
■ When unloading garments, check under the gray colored
seal at the front of the tub for small items.
2. Close t
3. Open the d
he washer door by pushing it firmly until the lock
clicks. The washer door will remain locked during the wash
cycle.
NOTES:
■ After any wash cycle is completed, the door must be
opened and then closed before a new cycle can begin.
■ The door can be opened if STOP is selected while the
ADD CLOTHES light is glowing or if the cycle has been
canceled.
■ See “To cancel a cycle” in “Changing Cycles, Options,
and Modifiers” section.
ispenser drawer and add laundry products to the
detergent, bleach, fabric softener, or oxygen based stain
fighter/ color-safe bleach compartments. Close drawer slowly
to avoid spills. See “Using the Dispenser.”
12
Use only “HE” High Efficiency detergent.
4. Turn on the washer by selecting POWER. Select one of the
cycles by turning the cycle selector. The indicator light for the
selected cycle will illuminate. When you are selecting a wash
cycle, the preset modifiers (Soil Level, Wash Temp, and Spin
Speed) for the cycle will illuminate. Selectable option settings
will glow amber. If an option or modifier is unavailable with
the selected cycle, the light will not illuminate. The preset
settings provide the recommended fabric care for the
selected cycle. The display shows the estimated time
remaining. See “Cycles.”
5. Sel
ect the desired OPTIONS. Not all Options are available
with all cycles. See “Options.”
6. Select the desired MODIFIERS. Not all Modifiers are available
with all Cycles and Options. See “Modifiers.”
7. If desir
ed, select the CYCLE SIGNAL. The signal is helpful
when you are washing items that should be removed from the
washer as soon as it stops. Select LOUD, SOFT, or OFF.
8. To begin the wash cycle immediately
Select and hold START (for approximately 1 second).
■ If you do not select START within 5 minutes of choosing
a cycle, the washer automatically shuts off.
■ When the wash cycle is complete, the CLOTHES CLEAN
status light glows, the door unlocks, and the wash load
can be removed from the washer. The washer powers
down automatically 60 minutes after the cycle is
complete an
d the CLOTHES CLEAN light goes off.
9. To begin the wash cycle later
Select Delay Start until the desired delay time (in hours)
shows in
the Estimated Time Remaining display. Select
START. The countdown to the wash cycle will show in the
display window, and the button indicator will blink until the
cycle begins.
IMPORTANT: W
hen delaying a cycle, use only powdered
detergents in the main wash compartment since liquid
detergents may seep out of the compartment during Delay
Start, before the wash cycle begins.
Choosing the Right Detergent
Use only High Efficiency detergents. The package for this type
of detergent will be marked “HE” or “High
Efficiency.” This wash
system, along with less water, will create too much sudsing with
a regular non-HE detergent. Using regular detergent will likely
result in washer errors, longer cycle times, and reduced rinsing
performance. It may also result in component failures and
noticeable mold or mildew. HE detergents are made to produce
the right amount of suds for the best performance. Follow the
manufacturer’s instructions to determine the amount of detergent
to use. Remember, concentrated detergents such as 2x or higher
will use less detergent based on load size.
Use only “HE” High Efficiency detergent.
To fill dispenser compartments
1. Pull out the dispenser drawer.
2. Add the desired laundry product to the proper compartment.
3. Push in
a spill).
the dispenser drawer slowly and completely (to avoid
Using the Dispenser
Your new washer has a dispenser drawer with four separate
compartments for your laundry products—one is for high
efficiency detergent, one is for liquid chlorine bleach, one is for
liquid fabric softener, and one is for oxygen based stain fighters
or color-safe bleach. Laundry products are diluted and dispensed
automatically at the proper time during the wash cycle, making it
unnecessary for you to return to the washer during the cycle to
add them.
It is normal for small amounts of water to remain in the
dispensers when the wash cycle is complete.
Do not put laundry products directly into the wash tub. Always
use the p
roper dispensers when adding laundry products.
Dispenser
A. Dispenser release lever
B. Oxygen based stain fighter / color-safe
ach compartment
ble
C. Detergent type selector
D. “HE” High Efficiency detergent compartment
E. Chlorine bleach compartment
F. Fabric softener compartment
13
Oxygen based stain fighter / color-safe bleach
mpartment
co
(Letter B in Dispenser Illustration)
Liquid or powdered oxygen bas
ed stain fighter / color-safe
bleach may be used in this compartment; however, powder is
recommended for optimal timed release. Add your oxygen based
stain fighter / color-safe bleach to this compartment when using
the TIMED OXI™ option. The oxygen based stain fighter / colorsafe bleach will automatically be dispensed during the wash
cycle if the TIMED OXI™ option is selected. Follow the
manufacturer’s directions for proper use.
High Efficiency “HE” detergent compartment
(Letters C and D in Dispenser Illustration)
Add liquid or powdered HE deter
your wash cycle. The detergent type selector (C) must always be
in the correct position for the detergent type used. Slide the
detergent type selector to the correct position.
IMPORTANT: If you are using the Delay Start option, powdered
detergent should be used in the compartment since liquid
detergents may seep out of the compartment, before the wash
begins.
■ Use the detergent manufacturer’s recommended amount
for the load size.
■ Liquid detergent:
A
gent to this compartment for
Chlorine bleach compartment
(Letter E in Dispenser Illustration)
Add no more than 2/3 cup (160 mL) liquid chlorine bleach to this
compartment. The bleach will be automatically diluted and
dispensed at the best time during the first rinse after the wash
cycle. This compartment cannot dilute powdered bleach.
■ Always measure liquid chlorine bleach. Use a measuring cup
with a pour spout; do not guess. Follow the manufacturer’s
directions for proper use.
■ Do not fill beyond the “MAX” level.
NOTE: Overf
■ At the end of the cycle, a small amount of water may be left
illing could cause garment damage.
in the dispenser. This is normal.
Fabric softener compartment
(Letter F in Dispenser Illustration)
Pour measured liquid fabric softener into the fabric softener
dispens
■ Do not overfill. The dispenser holds ¼ cup (60 mL) of fabric
■ The fabric softener is dispensed in the rinse cycle. If 2nd
■ Do not use fabric softener dispensing balls in this washer.
■ Do not spill or drip any fabric softener onto the clothes. ■ At the end of the cycle, a small amount of water may be left
NOTE: U
er, if desired.
softener.
Rinse is selected, the fabric softener will be dispensed during
the 2nd Rinse.
Dispensing balls will not operate correctly with this washer.
in the dispenser. This is normal.
se only liquid fabric softener in this dispenser.
Selector in position for liquid detergent
A. Detergent type selector
■ Powdered detergent:
A
Selector in position for powdered detergent
A. Detergent type selector
Pausing or Restarting
1. To pause the washer at any time, select STOP.
o continue the cycle, select and hold START (for
2. T
approximately 1 second).
Changing Cycles, Options, and Modifiers
Not all Options and Modifiers are available with all Cycles.
Available modifier selections will glow. Selectable options will
glow amber. If an option or modifier is unavailable with the
selected cycle, the light will not illuminate. Once an option or
modifier is selected it will glow green. Chosen options or
modifiers will glow green.
Cycles, Options, and Modifiers can be changed anytime before
START is selected.
To cancel a cycle and select a new cycle
1. Select STOP twice.
ect POWER.
2. Sel
3. Select desired cycle.
4. Select the desir
ed OPTIONS and MODIFIERS. Not all options
or modifiers are available to all cycles. See “Laundry Guide.”
ect and hold START (for approximately 1 second) to restart
5. Sel
the washer at the beginning of the new cycle.
To cancel a cycle
14
1.
Select STOP twice.
2.
The washer powers down, the door unlocks, and clothes can be removed.
NOTE: If the water level or the temperature is too high, the
washer will drain automatically before the door unlocks.
To change Options or Modifiers after the cycle has started
1. Select STOP once.
2. Select the desired OPTIONS or MODIFIERS. Not all options
or modifiers are available to all cycles. See “Laundry Guide.”
3. Select and hold START (for approximately 1 second) to
continue the cycle.
To drain the washer manually
1. Select STOP twice to cancel the wash cycle.
ect POWER.
2. Sel
3. Select DRAIN & SPIN.
ect and hold START (for approximately 1 second) to begin
4. Sel
the drain.
5. Wh
en the spin is complete, the door unlocks. Items can be
removed from the washer.
Status Lights
These lights show which portion of the cycle the washer is
operating. They also indicate when you can add an additional
item to the wash cycle and when the controls are locked.
Adding clothes after wash cycle has begun
This washer allows a 4-8 minute period in which other garments
may be added to the load and still be cleaned properly. You can
add items to the washer if the ADD CLOTHES status light is
glowing.
To add items when ADD CLOTHES light is glowing
1. Select STOP once. The washer will pause for a moment,
the washer door unlocks, and
2. To continue the cycle, close the door and select and hold
START (for approximately 1 second).
To add items when ADD CLOTHES light is not glowing
ou must cancel the current cycle by pressing STOP twice.
1. Y
This will cancel the wash cycle and options. The washer door
unlocks, and items can be added.
2. Close
NOTES:
■ When selecting a new cycle do not add additional detergent. ■ Adding an item after the “Add Clothes” light is off may not
the door and select the new cycle and options. Select
and hold START (for approximately 1 second).
allow for proper cleaning of that item.
then items can be added.
Sanitized
This Kenmore washer has a sanitizing temperature that is
certified by NSF International, an independent third-party testing
and certification organization. The certification verifies that the
sanitizing cycle reduces 99.9% of bacteria typically found on
clothing, bedding, and towels, and there is no carryover of
bacteria between loads after the cycle is complete.
If the “Steam Sanitize” wash temperature was selected, when the
wash cycle is complete, the SANITIZED status light glows, (the
CLOTHES CLEAN status light will glow green), the door unlocks,
and the wash load can be removed from the washer. The washer
powers down automatically 60 minutes after the cycle is
complete an
turn off. Only cycles with Steam Sanitize wash temperature
selected have been designed to meet the requirements of NSF
Protocol P172 for Sanitizing Efficacy.
d the SANITIZED light and CLOTHES CLEAN light
Certified to Sanitize
Locking controls
The Control Lock avoids unintended use of the washer. You can
also use the control lock feature to avoid unintended cycle or
option changes during a cycle. When CONTROL LOCKED is lit,
all buttons are disabled except for STOP and START. You can
lock the controls after a cycle begins or before POWER is
pressed.
To lock the controls
Select and hold CYCLE SIGNAL for 3 seconds after the cycle
sta
rts, or when the washer is powered off.
The status light next to the CYCLE SIGNAL button will glow.
To unlock the controls
Select and hold CYCLE SIGNAL for 3 seconds until the status
t turns off.
ligh
NOTE: To lock or unlock the controls when the washer is off,
press and hold CYCLE SIGNAL for 3 seconds.
Door Locked
When the status light glows, the door is locked.
Clothes Clean
When the wash cycle is complete, the CLOTHES CLEAN status
light glows, the door unlocks, and the wash load can be removed
from the washer. The washer powers down automatically
60 minutes after the cycle is complete and the CLOTHES CLEAN
light goes of
f.
15
Sensing/Revising Est. Time
The cycle times vary automatically based on your water pressure,
water temperature, detergent, and clothes load.
The washer will automaticall
adjust the Estimated Time Remaining display. While the washer is
sensing, the estimated time will flash and the Sensing/Revising
Est. Time status light will glow. When the sensing is complete, the
flashing stops, the status light goes off, and the Estimated Time
Remaining display is updated.
The cycle time will be extended if oversudsing occurs or the load
is unbalanced. The SUD routine removes extra suds and assures
proper rinsing of your garments. See “Troubleshooting.” During
the unbalance routine, the time displayed may pause until this
activity is complete, then resume with the remainder of the cycle.
y sense the progress in the cycle and
Cycles
Wash Cycles
Choose Wash Cycles by turning the selector knob. The cycle
indicator light will glow when selected. Each cycle is designed for
different types of fabric and soil levels. The modifier indicator
lights, on the right-hand side of the panel, will change as cycles
are selected.
Preset cycle settings
Each cycle has a preset Cycle Time, Water Temp, and Spin
Speed. The preset settings provide the recommended fabric care
for the selected cycle. See chart.
Cycle
Soil Level
(hr:min)
Express Wash
(2-3 items)
Handwash/
Wo
ol
Silk/Ultra
Delicate
Rinse & Spin N/A
Drain & Spin N/A
Clean Washer N/A
Whitest Whites Heavy
Heavy Duty Heavy
Kidswear Heavy
Bulky/Bedding Normal
Normal/Casual Normal
Light
(0:30)
Normal
(0:35)
Normal
(0:35)
(0:22)
(0:13)
(1:05)
(1:45)
(1:35)
(1:30)
(0:55)
(0:50)
Water Temp
Spin Speed
(Wash/Rinse)
Warm/Cold Extra High
Cool/Cold Low
Cool/Cold No spin
Cool/Cold Extra High
N/A Extra High
N/A N/A
Hot/Cold Extra High
Hot/Cold Extra High
Warm/Cold Extra High
Warm/Cold Extra Low
Warm/Cold High
■ Each cycle has a preset Soil Level (estimated cycle time),
Water Temperature, and Spin Speed and may have preset
Options. The preset settings provide the recommended fabric
care for the selected cycle.
■
The preset settings will glow green to show the preselected
options and modifiers, and can be changed anytime before
START is selected. Not all Options and Modifiers are available
with all cycles. Available modifier selections will glow amber.
(To change settings after the cycle has started, select STOP
once, then select the desired settings. Select and hold START
[for approximately 1 second] to continue the cycle.)
To change the preset cycle settings
Press the selector of each available setting until the desired
ing glows green.
sett
Express Wash
Use this cycle to wash small loads of 2-3 lightly soiled garments
that are needed in a hurry. This cycle combines fast-speed
tumbling, a shortened wash time, and extra high speed spin to
shorten drying time. Large wash loads will result in the machine
increasing the wash time.
Handwash/Wool
Use this cycle to clean washable woolen and special care
garments. (Check label instructions to make sure that the
garment is washable.) Similar to the way garments are hand
washed in a sink, the wash action of this cycle combines periods
of extra low tumbling speeds and soaking. Low spin speeds
minimize wrinkling.
■ Use mesh garment bags to wash undergarments such as
underwire bras, items with strings, and small items such as
infant socks.
■ Powdered detergents may not dissolve well in a slow-speed
cycle. For best results, use liquid detergent for slow-speed
cycles.
16
Silk/Ultra Delicate
Kidswear
Use this cycle to clean washable silk and ultra delicate garments.
(Check label instructions to make sure that garment is washable.)
This cycle gently tumbles and drains without spinning to gently
clean garments and minimize wrinkling. Garments will contain a
higher amount of water at the end of this cycle, because there is
no spinning action.
■ Use mesh garment bags as necessary. ■ Powdered detergents may not dissolve well in a slow-speed
cycle. For best results, use liquid detergent for slow-speed
cycles.
Rinse & Spin
Use this cycle to rinse, drain, and spin your wash load. This cycle
combines fast-speed tumbling and high-speed spin. If desired,
you can reduce the spin speed by selecting the speed you want
from the SPIN SPEED modifier.
Rinse & Spin is useful for
■ Loads that need rinsing only. ■ Adding fabric softener to a load using the fabric softener
dispenser.
Drain & Spin
Use this cycle to drain your washer or to drain and spin your
wash load. The spin speed is preset to high. If desired, you can
reduce the spin speed by selecting the speed you want from the
SPIN SPEED modifier.
NOTE: Loa
woolens should be drained with no spin or low spin to avoid
fabric stress.
ds of synthetics, delicate fabrics, handwashables, and
Clean Washer
Use the Clean Washer cycle once a month to keep the inside of
your washer fresh and clean. This cycle uses a higher water level
in combination with liquid chlorine bleach and steam, to
thoroughly clean the inside of your washing machine. This cycle
should not be interrupted. See “Cleaning Your Washer” in the
“Washer Care” section.
IMPORTANT: D
during the Clean Washer cycle. Use this cycle with an empty
wash drum.
o not place garments or other items in the washer
This cycle is specifically designed to clean and thoroughly rinse
children’s clothing. The Skincare Rinse II with extra water
provides optimal rinse performance to minimize detergent
residue. This cycle combines fast-speed tumbling and extra high
spin speeds to shorten drying time.
Bulky/Bedding
Use this cycle to wash large items such as blankets and
comforters. This cycle starts with a soak to thoroughly saturate
your large load. This is followed by medium wash action and
extra low spin speeds to maintain load balance.
Normal/Casual
Use this cycle to wash loads of no-iron fabrics such as sport
shirts, blouses, casual business clothes, permanent press
blends, cottons and linens, and synthetic fabrics. This cycle
combines medium-speed tumbling, high-speed spin, and a load
cooling process to reduce wrinkling.
NOTE: For
Cycle.
the best energy performance, use the Normal/Casual
Normal Washer Sounds
As with any new product, you will hear sounds that you are not
accustomed to. You may hear various sounds when the door is
locked or unlocked, and during the washing, rinsing, or spinning
process. Between changes in wash actions, there will be
momentary pauses. You will hear water spraying and splashing
during the wash and rinse cycles. These new sounds and pauses
are part of normal washer operation. (See “Troubleshooting.”)
Options
You can customize your wash by adding options to your cycle
selections. You can add or change an option after starting a cycle
anytime before the selected option begins. Not all Options are
available with all cycles. Current selections will glow green. If an
option is unavailable with a selected cycle, the light will not
illuminate.
Whitest Whites
This cycle is especially designed for cleaning loads of soiled
white fabrics with the addition of bleach. Hot washing
temperatures assure optimal bleach activity. An additional rinse
provides optimal rinse performance to avoid chlorine residues on
your laundry. This cycle combines fast-speed tumbling, longer
wash time, and extra high speed spin to shorten drying time.
Heavy Duty
Use this cycle to wash loads of sturdy, colorfast fabrics and
heavily soiled garments. This cycle combines fast-speed
tumbling, longer wash time, and extra high speed spin to shorten
drying times. If the water temperature is lower than needed for
this cycle, the heater will warm the water to the optimum
temperature.
■ See the “Laundry Guide” section for an overview of possible
options for each Wash Cycle selection.
■ You can select more than one option for a cycle. Some
options cannot be added to some cycles. For example,
STEAM TREAT™ cannot be added to the Express Wash
cycle.
■ If an option is unavailable with a selected cycle, there will be
3 short tones, and the light for that option will not glow when
ected.
sel
17
My Cycle
Button Sounds
My Cycle allows you to store a customized wash cycle
for future use.
To Customize a Wash Cycle:
1. Select a cycle.
2. Select the
3. Select the desired MODIFIERS.
o save the cycle, press and hold MY CYCLE (approximately
4. T
3 seconds) until a beep sounds.
5. Pr
ess START.
o reuse this cycle at another time, select MY CYCLE and
6. T
press START.
desired OPTIONS.
STEAM TREAT™
Use this option for heavily soiled loads that need improved stain
treatment, loads with multiple types of stains, or loads you
suspect as having stains, but are afraid may have been missed
(no sorting or searching for stains). When STEAM TREAT™ is
selected, the water temperature of the selected wash cycle is
automatically set to warm. The water will then be slowly heated
to the temperature selected, along with steam, to aid in stain
removal. This option will provide optimal removal of organic
stains such as blood. This option is available on the following
cycles: Normal/Casual, Bulky/Bedding, Kidswear, Heavy Duty,
Whitest Whites.
TIMED OXI™
Use this option when using an oxygen based stain fighter or
color-safe bleach in the dispenser. Selecting this option will
ensure these products dispense during the wash cycle at the
proper time for improved performance.
■ Add using the Oxi / Color-safe bleach section of the
dispenser drawer.
Autosoak
Button sounds are used to notify you of what has been selected
or to let you know when something is not available. Button
sounds may be turned on or off by selecting BUTTON SOUNDS.
Save Energy Plus
The Save Energy Plus option allows you to increase your energy
savings on the higher temperature cycles (Whitest Whites and
Heavy Duty) while maintaining cleaning performance by
lengthening the wash time by only 10 minutes.
Delay Start
To begin the wash cycle later, select DELAY START until the
desired delay time (in hours) shows in the Estimated Time
Remaining display, and then select START. The countdown to the
wash cycle will show in the display window, and the button
indicator will blink until the cycle begins.
IMPORTANT:
detergents in the high efficiency “HE” detergent compartment
since liquid detergents may seep out of the compartment during
DELAY START, before the wash cycle begins.
When delaying a cycle, use only powdered
Cycle Signal
This signal is helpful when you are removing items from the
washer as soon as it stops. Select Loud, Soft, or Off.
Modifiers
Preset cycle settings of Water Temperature, Spin Speed, and
Rinse Options can be changed. You can change a modifier after
starting a cycle anytime before the selected Modifier begins. Not
all Modifiers are available with all options and cycles. Available
modifier settings will glow amber. Current selections will glow
green. If an option is unavailable with a selected cycle, the light
will not illuminate.
Use the Autosoak option to remove small spots or stains on
fabrics. This option provides up to a 30-minute soak time prior
to the start of the selected cycle.
Using the Autosoak option:
soak time with warm or cold water followed by drain.
1. Sel
ect desired cycle.
2. Choose the
ect Autosoak. When selected, the bottom half of the
3. Sel
button indicator will glow green.
4. Sel
ect and hold START (approximately 1 second).
desired temperature.
The Autosoak option provides a
2nd Rinse
A second rinse can be used to aid in the removal of detergent or
bleach residue from garments. This option provides an additional
rinse with the same water temperature as the normal rinse. This is
the default rinse setting for the Whitest Whites cycle. When 2nd
Rinse is selected, the top half of the button indicator light will
glow green.
SkinCare Rinse II
This option provides the best rinse level, to allow for even better
detergent removal. Press the 2nd Rinse/Skincare Rinse II button
twice to select this option. When Skincare Rinse II is selected, the
bottom half of the button indicator light will glow green.
■ To change cycle time, select SOIL LEVEL button. ■ To change the water temperature, select the WASH TEMP
button until the desired setting glows green.
■ To change the spin speed, select the SPIN SPEED button
until the desired setting glows green.
Wash Temp
Select a water temperature based on the type of load you are
washing. Use the warmest wash water safe for fabrics. Follow
garment label instructions.
■ This Kenmore washer has a Steam Sanitize water
temperature that is certified by NSF International, an
independent third-party testing and certification organization.
The certification verifies that the sanitizing cycle reduces
99.9% of bacteria typically found on clothing, bedding, and
towels, and there is no carryover of bacteria between loads
after the cycle is complete.
18
■ The Steam Sanitize temperature provides an extra high
temperature to remove 99.9% of certain bacteria. It is
recommended that you set your hot water heater to 120ºF
(49ºC) to ensure proper performance during this cycle.
Warm rinses leave the loads drier than cold rinses. Warm rinses
inc
rease wrinkling. In cold climates, a warm rinse makes the load
more comfortable to handle. Cold rinses save energy. Only cycles
with Steam Sanitize wash temperature selected have been
designed to meet the requirements of NSF Protocol P172 for
Sanitizing Efficacy.
Auto Temp Control
ATC (Auto Temp Control) electronically senses and maintains a
Certified to Sanitize
■ The Steam Sanitize temperature uses high water
temperatures. Please check garment care label to avoid
garment damage.
■ In wash water temperatures colder than 60°F (15.6°C),
detergents do not dissolve well. Soils may be difficult
to remove.
uniform water temperature. ATC regulates incoming hot and cold
water. The ATC is automatically turned on when a cycle is
selected. (See “Preset Cycle Settings” in “Cycles.”)
■ ATC works for the wash temperature with Steam Sanitize,
Hot, Warm, and Cool settings.
■ The Cold wash temperature depends on the cold water at
your faucet.
■ ATC works for the rinse temperature where the wash temp
setting is marked with an asterisk, such as Warm*. All other
rinse temperatures are cold.
Laundry Guide
Refer to this chart for suggested load types and their corresponding cycles. Listed to the right are the options available to each of these washer cycles.
CYCLE SUGGESTED LOAD TYPE AVAILABLE OPTIONS
Delay
Start
STEAM
AT™
TRE
TIMED
OXI™
Autosoak Save
Energy
Plus
2nd Rinse/
Skincare
Rinse II
Express Wash Small loads of 2-3 lightly soiled cotton,
pol
yester, nylon, and cotton blends.
Handwash/Wool Woolens with a felt-free finish and special-care
✓ ✓
✓ ✓
items identified as machine washable.
Silk/Ultra
Delicate
Silk or Ultra Delicate fabrics identified as
machine washable.
✓ ✓
Rinse & Spin All loads ✓ ✓
Drain & Spin All loads ✓
Clean Washer No clothes ✓
Whitest Whites Soiled white fabrics ✓ ✓ ✓ ✓ ✓ ✓
Heavy Duty Heavily soiled underwear, towels, shirts, etc.,
✓ ✓ ✓ ✓ ✓ ✓
made of cotton
Kidswear Children’s clothing or any fabric that requires
tra rinsing
ex
✓ ✓ ✓ ✓ ✓
Bulky/Bedding Normally soiled blankets and comforters ✓ ✓ ✓ ✓ ✓
Normal/Casual Normally soiled blouses, shirt
s, overalls, etc.,
✓ ✓ ✓ ✓ ✓
made of polyester, nylon, cotton, linen, or
cotton blends
19
LAUNDRY TIPS
Preparing clothes for washing
Follow these recommendations to help you prolong the life of
your garments.
■ Use only High Efficiency detergents. The package for this type
of detergent will be marked “HE” or “High Efficiency.” This
wash system, along with less water, will create too much
sudsing with a regular non-HE detergent. Using regular
detergent will likely result in washer errors, longer cycle times,
and reduced rinsing performance. It may also result in
component failures and noticeable mold or mildew. HE
detergents are made to produce the right amount of suds for
the best performance. Follow the manufacturer’s instructions
to determine the amount of detergent to use.
concentrated detergents such as 2x or higher will use less
detergent based on load size.
Use only HE High Efficiency detergent.
■ Close zippers, snaps, and hooks to avoid snagging other
items. Remove pins, buckles, and other hard objects to avoid
scratching the washer interior. Remove non-washable trim
and ornaments.
■ Empty pockets and turn them inside out. ■ Turn down cuffs; brush away lint and dirt. ■ Turn wool and synthetic knits inside out to avoid pilling. ■ Tie strings and sashes so they will not tangle. ■ Mend tears, loose hems, and seams. ■ Treat spots and stains. ■ Stained or wet garments should be washed promptly for best
results.
■ Mix large and small items, avoid washing single items, and
load evenly.
■ Wash small items, such as infant socks, in a mesh garment
bag. To create a balanced load, it is recommended that more
than one garment bag be used, and that each garment bag
be filled with equal amounts of material.
NOTE: If you are washing only small items, it is
recommended that more than one mesh garment bag be
used, and that each garment bag be filled with equal
amounts of material.
Remember,
Sorting
■ Separate heavily soiled items from lightly soiled ones, even if
they would normally be washed together. Separate lint-givers
(towels, chenille) from lint-takers (corduroy, synthetics,
permanent press). When possible, turn lint-givers inside out.
■ Separate dark colors from light colors, colorfast items from
noncolorfast items.
■ Sort by fabric and construction (sturdy cottons, knits, delicate
items).
Unloading
■ Remove clothes from washer after the cycle is completed.
Metal objects such as zippers, snaps, and buckles may rust
if left in the washer basket for a long time.
■ When unloading garments, occasionally check under the gray
colored seal at the front of the tub for small items.
Loading
Loading suggestions
Heavy Work Clothes
4 jeans
4workpants
4workshirts
Towels
10 bath towels
10 hand towels
Mixed Load
3 sheets (1 king, 2 twin)
4 pillowcases
3shirts
3blouses
Delicates
3camisoles
4slips
4 panties
EXPRESS WASH cycle
(2-3 garments)
2 dress shirts
2sweatpants
2sweatshirts
14 washcloths
9T-shirts
9shorts
10 handkerchiefs
2 bras
2nighties
1 pair dress pants
20
WASHER CARE
Cleaning Your Washer
The Washer Maintenance Procedure should be performed on a
monthly basis.
Cleaning the door seal
1. Open the washer door and remove any clothing or items from
the washer.
2. Inspect
3. If stained areas are found, wipe down these areas of the
IMPORTANT:
■ Wear rubber gloves when cleaning for prolonged periods. ■ Refer to the bleach manufacturer’s instructions for proper
the gray colored seal between the door opening and
the basket for stained areas. Pull back the seal to inspect
areas under the seal. Remove any foreign objects.
A
A. Seal
seals, using the procedure that follows.
a) Mix a dilute solution, using 3/4 cup (177.4 mL) of liquid
chlorine bleach, and 1 gal. (3.8 L) of warm tap water.
b) Wipe the seal area with the dilute solution, using a damp
h.
clot
c) Let stand 5 minutes.
d) Wipe down area thoroughly with a dry
washer interior air dry with door open.
use.
cloth and let the
Begin procedure
1. Open the washer door and remove any clothing or items from
the washer.
2. Open the d
(160 mL) of liquid chlorine bleach to the bleach compartment.
NOTE:
than
over time.
3. Close
ect the CLEAN WASHER cycle.
4. Sel
ess START.
5. Pr
NOTE: Th
again, and then the cycle will continue.
■ The machine will bring in some inlet water, and the basket
will rotate while the washer runs a short sensing cycle.
This will take approximately 3 minutes.
6. Th
e cycle will determine whether clothing or other items are
in the washer.
a) b)If no items are detected in the washer, it will proceed to
Step 7
If any items are detected in the washer, “rL” will be
displayed, and the WASH and CONTROLS LOCKED
lights will remain lit. The door will unlock. Open and
remove any garments in the wash drum.
■ Press STOP to cancel the failure code. Then repeat
7. On
ce the cycle has begun, allow the cycle to complete.
8. After the cycle is complete, leave the door open slightly,
to allow for better ventilation and
ispenser drawer and immediately add 2/3 cup
Do not add any detergent to this cycle. Use of more
2
/3 cup (160 mL) of bleach will cause product damage
the washer door and dispenser drawer.
e basket will rotate, then the door will unlock, lock
.
steps 3, 4, and 5 to start the cycle again.
drying of washer interior.
Always do the following to maintain washer freshness
■
Use only HE High Efficiency detergent.
■
Leave the door slightly open after each cycle to allow for better ventilation and drying of washer interior.
■
Repeat the cleaning procedure monthly.
■
If the procedure does not sufficiently improve the machine freshness, evaluate your installation and usage conditions for other causes.
Washer Maintenance Procedure
This washer has a special cycle that uses higher water volumes
and steam, in combination with liquid chlorine bleach to
thoroughly clean the inside of the washer.
NOTES:
■ Read these instructions completely before beginning the
cleaning process.
■ If necessary, the cleaning cycle may be interrupted by
pressing the STOP button. However, this will not immediately
stop the cycle. The machine will display “int” (interrupt) and
continue with several rinse and drain steps to ensure that all
remaining bleach is rinsed from the washer.
Cleaning the exterior
Use a soft damp cloth or sponge to wipe up any spills.
Occasionally wipe the outside of your washer to keep it looking
new. Use mild soap and water. Do not use abrasive products.
Cleaning the dispenser drawer
The dispenser drawer is removable for easy cleaning.
1. Unlock the
in the oxygen based stain fighter /
compartment. See “Using the Dispenser.” Remove the
drawer.
2. Remove the
compartments and the selector).
3. W
ash the parts under running water.
eplace the inserts and return the dispenser to the drawer.
4. R
dispenser drawer by pressing the Release Lever
color-safe bleach
inserts (the siphon from the softener and bleach
21
Water Inlet Hoses
Replace inlet hoses after 5 years of use to reduce the risk of hose
failure. Periodically inspect and replace inlet hoses if bulges,
kinks, cuts, wear, or leaks are found.
When replacing your inlet hoses, record the date of replacement.
Vacation, Storage, and Moving Care
Install and store your washer where it will not freeze. Because
some water may stay in the hoses, freezing can damage your
washer. If storing or moving your washer during freezing weather,
winterize it.
Non-use or vacation care:
Operate your washer only when you are at home. If you will be on
vacation or not using your washer for an extended period of time,
you should:
■ Unplug washer or disconnect power. ■ Turn off the water supply to the washer. This helps avoid
unintended flooding (due to a water pressure surge) while you
are away.
■ Slightly open door to provide ventilation.
To winterize washer:
1. Put 1 qt (1 L) of R.V.-type antifreeze in the drum.
2. Run washer on a Drain & Spin cycle.
3. Unplug wa
4. Shut
5. Disconnect water inlet hoses from faucets and drain.
sher or disconnect power.
off both water faucets.
To use washer again:
1. Flush water pipes. Reconnect water inlet hoses to faucets.
Turn on both water faucets.
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
re, or electrical shock.
2. Plug in washer or reconnect power.
un the washer through the Express Wash cycle with 1/2 the
3. R
manufacturer’s recommended amount of HE detergent for a
medium-size load, to clean the washer and remove the
antifreeze, if used.
To transport the washer:
1. If washer will be moved during freezing weather, put in 1 qt
(1 L) of R.V.-type antifreeze in the drum. Run washer on a
D
rain & Spin cycle.
2. Unplug the
3. Disconnect the
to rear panel clips.
4. Shu
5. Di
IMPORTANT: Call for
Washer must be transported in the upright position. To avoid
suspension and structural damage to your washer, it must be
properly set up for relocation by a certified technician.
t off both water faucets.
sconnect the water inlet hoses from faucets, then drain the
hoses and clip them to the rear panel of the washer.
Reinstalling the washer
1. Follow the “Installation Instructions” to locate, level, and
connect the washer.
2. Run the washer through the Express Wash cycle with 1/2 the
manufacturer’s recommended amount of HE detergent for a
medium-size load, to clean the washer and remove the
antifreeze, if used.
power cord.
drain hose from the drain system and attach
service. Do not reuse transport bolts.
22
TROUBLESHOOTING
First try the solutions suggested here to possibly avoid the cost of a service call...
Washer displaying code message and tone sounds
■ “F20” (Water Inlet Problem—no water or insufficient
water supply)
Select STOP twice to cancel the cycle. Unplug washer or
disconnect power
Check the following:
Are both hot and cold water faucets completely turned on?
Are screens at inlet hose connection
Are water inlet hoses kinked?
Are water inlet hoses frozen?
Plug in washer or reconnect power. Re-select cycle and press
ART. If the problem remains, call for service.
ST
■ “F21” (Drain Problem)
Select STOP twice to cancel the cycle. Unplug washer or
disconnect power
Check the following:
Is the drain hose kinked?
Is the drain hose frozen?
Is the drain hose clogged?
Is the drain hose more than 96" (2.4 m) above the floor?
Plug in washer or reconnect power. Re-select cycle and press
ART. If the problem remains, call for service.
ST
■ “SUD” (Suds Routine)
When excessive suds are detected, a suds routine
tomatically starts. This routine removes extra suds and
au
assures proper rinsing of your garments. “SUD” is displayed
during rinsing to inform you that Suds Routine was activated.
Use only HE (High Efficiency) detergents.
■ “F22” (Front door lock)
Select STOP twice to cancel the cycle.
Is the washer door firmly shut?
The door must be completely closed for the washer to
e. The door may look closed, but may not be latched.
operat
Open the door and close firmly.
Were you washing a large load?
Before you close the washer door, check for laundry items
sticking out beyond the door opening. Leave enough space
in the washer to allow the clothes to tumble freely. An
overloaded basket may keep the door from shutting
completely. Reduce your load size if needed.
Press POWER, re-select cycle and press START.
■ “F” Codes other than F20, F21, and F22
Select STOP twice to cancel the cycle. Select DRAIN & SPIN
if the
re is excessive water in the washer.
Re-select cycle and press START. If the problem remains, call
for service.
.
to washer clogged?
.
Washer won’t start
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
re, or electrical shock.
■ Check the following:
Is the power cord plugged into a grounded 3 prong outlet?
Is the washer door firmly shut?
Has a cycle been selected, but START has not been selected
d held for 1 second?
an
Was the door open after completion of last cycle?
Washer won’t fill, wash, or rinse
■ Check the following:
Is the power cord plugged into a grounded 3 prong outlet?
Is there power at the plug? Check electrical source or call
electrician.
Are the hot and cold water faucets turned on?
Is the water inlet hose kinked?
Are the water inlet valve screens clogged?
Turn off the water and remove inlet hoses from the washer.
emove any accumulated film or particles. Reinstall hoses,
R
turn water on, and check for leaks.
Washer stops
■ Check the following:
Is the power cord plugged into a grounded 3 prong outlet?
Is there power at the plug?
Check electrical source or call electrician.
Has a household fuse blown, or has a circuit breaker tripped?
Replace the fuse or reset the circuit breaker. If the problem
ontinues, call an electrician.
c
Are you using an extension cord?
Do not use an extension cord.
23
Washer won’t drain or spin
■ Is the drain hose kinked? Is the drain hose clogged, or the
end of the drain hose more than 96" (2.4
m) above the
floor?
■ Is your voltage low?
Check electrical source or call electrician. Do not use an
extension cord.
■ Is the “SUD” routine active?
Cycle will complete once extra suds are removed.
■ Is the load balanced?
A single or bulky item may cause imbalance. Add more items
or redistribute the load.
Washer makes noise or vibrates
■ Is the washer level?
The washer must be level. The four feet should be properly
installed, and the nuts should be tightened against the
washer cabinet.
As water is drained from the washer, you may hear air being
pulled through the pump. This happens during the end of
draining. It is normal.
■ Are you washing items with metal snaps, buckles,
or zippers?
You may hear metal items touching the washer drum.
This is normal.
■ Is washer installed on a sturdy and solid floor?
Refer to the “Installation Instructions” for flooring
requirements. Noise and vibration may be reduced by
securing a piece of ¾" (19.1 mm) plywood underneath your
washer. The plywood may extend underneath both washer
and dryer to keep them at equal heights.
Water near washer
■ Check household plumbing for leaks. ■ Are the inlet hose connections tight?
For inlet hose connections, see “Connect the Inlet Hoses.”
Dispensers clogged or leaking
■ Are the laundry products in the correct dispenser
compartment?
Add the correct amounts of detergent, fabric softener, or
liquid chlorine bleach to the correct compartments. Add
powdered or liquid color-safe bleach to the Main Wash
compartment. Be sure to match powdered color-safe bleach
with powdered detergent or match liquid color-safe bleach
with liquid detergent.
■ Is the detergent type separator in the correct position?
Separator should be in the lowered position when using liquid
detergent and in the upper position when using powdered
detergent. See “Cleaning Your Washer.”
Washer odor
■ See “Cleaning Your Washer.” ■ Are you using HE detergent?
Use of non-HE detergent can cause a film residue which can
result in odor.
■ Did you leave the door open after use?
This washer has a tight seal to avoid water leaks. To avoid
odors leave the door open to allow the washer to dry
between uses.
Load too wet
■ Did you use the right cycle for the load being washed?
Select a cycle with a higher spin speed.
■ Did you wash a single item or bulky items or have you
overloaded the washer?
A single item, bulky items, or overloading may cause
imbalance. Add items or try to evenly distribute your wet
laundry in the drum, and start a Drain & Spin cycle. If the
laundry is still wet, take half of the load out of the washer and
try again.
Residue or lint on load
■ Did you add detergent to the dispenser?
For best results, add detergent to the detergent
compartment. Do not add detergent to the washer drum.
■ Did you sort properly?
Sort lint givers (towels, chenille) from lint takers (corduroy,
synthetics). Also sort by color.
■ Did you overload the washer?
Do not overload the washer. The washer can be fully loaded,
but not tightly packed. The wash load must be balanced. Lint
can be trapped in the load if overloaded.
■ Check the following:
Was paper or tissue left in pockets?
■ Did you use enough HE detergent?
Use enough detergent to remove lint and hold it
in suspension. Use only HE detergent. Follow the
manufacturer’s instructions to determine the amount
of detergent to use.
■ Is your water colder than 60°F (15.6°C)?
Wash water colder than 60°F (15.6°C) may not completely
dissolve the detergent.
■ Are you using a low speed wash cycle?
Powdered detergents may not dissolve well in a slow-speed
cycle. For best results, use liquid detergent for slow-speed
cycles such as Handwash/Wool and Silk/Ultra Delicate.
Stains on load
■ Did you add detergent to the dispenser?
For best results, add detergent to the detergent
compartment. Do not add detergent to the washer drum.
■ Did you use enough HE detergent?
Use enough detergent to remove soil and hold it
in suspension. Use only HE detergent. Follow the
manufacturer’s instructions to determine the amount
of detergent to use.
■ Is there above average iron (rust) in water?
You may need to install an iron filter.
■ Did you properly sort the load?
Sort dark clothes from whites and lights.
■ Did you unload the washer promptly?
To avoid the transfer of dye, unload the washer as soon
as it stops.
■ Did you use a fabric softener dispensing ball?
Dispensing balls will not operate correctly with this washer.
Add liquid fabric softener to the fabric softener compartment.
24
Loading...