HP HCPL-2232, HCPL-0211, HCPL-0201, HCPL-2202, HCPL-2201 Datasheet

H

Very High CMR, Wide VCC Logic

Gate Optocouplers

Technical Data

Features

•10 kV/μs Minimum Common Mode Rejection (CMR) at

VCM = 1000 V (HCPL-2211/2212/0211/ 2232, HCNW2211)

•Wide Operating VCC Range: 4.5 to 20 Volts

•300 ns Propagation Delay Guaranteed over the Full Temperature Range

•5 Mbd Typical Signal Rate

•Low Input Current (1.6 mA to 1.8 mA)

•Hysteresis

•Totem Pole Output (No Pullup Resistor Required)

•MIL-STD-1772 Version Available (HCPL-52XX/62XX)

Applications

•Isolation of High Speed Logic Systems

•Computer-Peripheral Interfaces

•Microprocessor System Interfaces

•Ground Loop Elimination

•Pulse Transformer Replacement

•High Speed Line Receiver

•Power Control Systems

• Available in 8-Pin DIP,	Functional Diagram
SOIC-8, Widebody Packages

	• Guaranteed Performance			HCPL-2201/11
				HCPL-0201/11
	from -40°C to 85°C
				HCNW2201/11
	• Safety Approval	NC	1	8	VCC
	UL Recognized -2500 V rms		2	7	VO
	for 1 minute (5000 V rms	ANODE
	for 1 minute for	CATHODE	3	6	NC
	HCNW22XX) per UL1577
	CSA Approved	NC	4	5	GND
	VDE 0884 Approved with			SHIELD
	VIORM = 630 V peak (HCPL-			HCPL-2231/32
	2211/2212 Option 060 only)	ANODE 1	1	8	VCC
	and VIORM = 1414 V peak
	(HCNW22XX only)	CATHODE 1	2	7	VO1
	BSI Certified (HCNW22XX
	only)	CATHODE 2	3	6	VO2

ANODE 2 4	5	GND
	SHIELD

HCPL-2201 HCPL-2202 HCPL-2211 HCPL-2212 HCPL-2231 HCPL-2232 HCPL-0201 HCPL-0211 HCNW2201 HCNW2211

Description

The HCPL-22XX, HCPL-02XX, and HCNW22XX are opticallycoupled logic gates. The HCPL-22XX, and HCPL-02XX contain a GaAsP LED while the HCNW22XX contains an AlGaAs LED. The detectors have totem pole output stages and optical receiver input stages with built-in Schmitt triggers to provide logiccompatible waveforms, eliminating the need for additional waveshaping.

A superior internal shield on the HCPL-2211/12, HCPL-0211,

		HCPL-2202/12
NC	1	8	VCC
ANODE	2	7	NC
CATHODE	3	6	VO
NC	4	5	GND
		SHIELD

TRUTH TABLE (POSITIVE LOGIC)

LED	VO
ON	HIGH
OFF	LOW

A 0.1 μF bypass capacitor must be connected between pins 5 and 8.

CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD.

5965-3595E

1-131

HCPL-2232 and HCNW2211 guarantees common mode transient immunity of 10 kV/μs at a common mode voltage of 1000 volts.

Selection Guide

The electrical and switching characteristics of the HCPL22XX, HCPL-02XX and HCNW22XX are guaranteed from

-40°C to +85°C and a VCC from 4.5 volts to 20 volts. Low IF and

wide VCC range allow compatibility with TTL, LSTTL, and CMOS logic and result in lower power consumption compared to other high speed couplers. Logic signals are transmitted with a typical propagation delay of 150 ns.

						Small-	Widebody
Minimum CMR			Input	8-Pin DIP (300 Mil)		Outline SO-8	(400 Mil)	Hermetic
			On-
				Single	Dual	Single	Single	Single and
dV/dt			Current	Channel	Channel	Channel	Channel	Dual Channel
(V/μs)	VCM (V)		(mA)	Package	Package	Package	Package	Packages
1,000	50	1.6		HCPL-2200[1,2]		HCPL-0201	HCNW2201
				HCPL-2201
				HCPL-2202
			1.8		HCPL-2231
2,500	400	1.6		HCPL-2219[1,2]
5,000[3]	300[3]	1.6		HCPL-2211		HCPL-0211	HCNW2211
				HCPL-2212
		1.8			HCPL-2232
1,000	50	2.0						HCPL-52XX[2]
								HCPL-62XX[2]

Notes:

1.HCPL-2200/2219 devices include output enable/disable function.

2.Technical data for the HCPL-2200/2219, HCPL-52XX and HCPL-62XX are on separate HP publications.

3.Minimum CMR of 10 kV/μs with VCM = 1000 V can be achieved with input current, IF, of 5 mA.

Ordering Information

Specify Part Number followed by Option Number (if desired).

Example:

HCPL-2211#XXX

060 = VDE 0884 VIORM = 630 V peak Option* 300 = Gull Wing Surface Mount Option**

500 = Tape and Reel Packaging Option

Option data sheets available. Contact your Hewlett-Packard sales representative or authorized distributor for information.

*For HCPL-2211/2212 only.

**Gull wing surface mount option applies to through hole parts only.

Schematic

			1 IF1
			+
		ICC	VF1
		VCC	–
			2
		8
2	IF	IO
+		VO
VF
–
3
		GND	3
	SHIELD		–
		5
			VF2
	HCPL-2201/02/11/12
			+
	HCPL-0201/11		4	IF2
	HCNW2201/11

ICC

	VCC
	8
	IO1
	VO1
	7
SHIELD
	IO2
	VO2
	6
SHIELD	GND
	5
	HCPL-2231/32

1-132

Package Outline Drawings

8-Pin DIP Package (HCPL-2201/02/11/12/31/32)

						9.65						± 0.25															7.62 ± 0.25
																								(0.300 ± 0.010)
					(0.380							± 0.010)
TYPE NUMBER			8				7						6						5				OPTION CODE*		6.35			± 0.25
																								(0.250				± 0.010)
						HP XXXXZ																	DATE CODE

YYWW

UR

1	2	3	4	UL
				RECOGNITION
1.19 (0.047) MAX.			1.78 (0.070) MAX.

							5° TYP.				0.254	+ 0.076
												- 0.051
										(0.010		+ 0.003)
												- 0.002)
	4.70 (0.185) MAX.

0.51 (0.020) MIN.

2.92 (0.115) MIN.

1.080

± 0.320

0.65 (0.025) MAX.

(0.043

± 0.013)

2.54

± 0.25

(0.100

± 0.010)

DIMENSIONS IN MILLIMETERS AND (INCHES).

*MARKING CODE LETTER FOR OPTION NUMBERS "V" = OPTION 060

OPTION NUMBERS 300 AND 500 NOT MARKED.

8-Pin DIP Package with Gull Wing Surface Mount Option 300 (HCPL-2201/02/11/12/31/32)

																													PAD LOCATION (FOR REFERENCE ONLY)
							9.65 ± 0.25																																	1.016 (0.040)
						(0.380 ± 0.010)
																																															1.194 (0.047)
			8					7							6				5
																																																										4.826					TYP.
																																																										(0.190)
																									6.350 ± 0.25
																									(0.250 ± 0.010)																																						9.398 (0.370)
																																																															9.906 (0.390)
		1				2							3					4
																																																																0.381 (0.015)
																													1.194 (0.047)																																			0.635 (0.025)
																													1.778 (0.070)
																		1.780											9.65 ± 0.25
1.19																						(0.070)																						(0.380 ± 0.010)
																								MAX.																					7.62 ± 0.25
(0.047)
																																									(0.300 ± 0.010)
MAX.																																																																			+ 0.076
																																																																	0.254
																																																																			- 0.051
																									4.19			MAX.																																			(0.010				+ 0.003)
																		(0.165)
																																																																			- 0.002)

1.080	± 0.320
(0.043	± 0.013)																								0.635 ± 0.25
																							(0.025 ± 0.010)								12° NOM.
								2.54						0.635		± 0.130
	(0.100)													(0.025		± 0.005)

BSC

DIMENSIONS IN MILLIMETERS (INCHES).

LEAD COPLANARITY = 0.10 mm (0.004 INCHES).

1-133

Small-Outline SO-8 Package (HCPL-0201/11)

										8				7					6			5
																								5.842 ± 0.203
																		XXX				(0.236 ± 0.008)
3.937	± 0.127																														TYPE NUMBER
																	YWW
(0.155	± 0.005)
																															(LAST 3 DIGITS)
																															DATE CODE
										1				2					3			4
0.381	± 0.076
(0.016	± 0.003)																											1.270		BSG
																						(0.050)
											5.080 ± 0.127																			7°				45° X		0.432
											(0.200 ± 0.005)																									(0.017)

3.175 ± 0.127

(0.125 ± 0.005) 1.524

(0.060)

0.152 ± 0.051

(0.006 ± 0.002)

DIMENSIONS IN MILLIMETERS (INCHES).	0.305	MIN.
LEAD COPLANARITY = 0.10 mm (0.004 INCHES).	(0.012)

0.228 ± 0.025

(0.009 ± 0.001)

8-Pin Widebody DIP Package (HCNW2201/11)

						11.15 ± 0.15																						11.00
					(0.442 ± 0.006)																							(0.433) MAX.
																											9.00 ± 0.15
	8						7				6				5								(0.354 ± 0.006)
																				TYPE NUMBER
									HP											DATE CODE
					HCNWXXXX
									YYWW
	1						2				3				4
																										10.16 (0.400)
																												TYP.

1.55

(0.061)

MAX. 7° TYP. 0.254 + 0.076 - 0.0051

+ 0.003) (0.010 - 0.002)

																																					5.10 MAX.
																																			(0.201)
																														3.10 (0.122)
																															3.90 (0.154)				0.51 (0.021) MIN.
	2.54 (0.100)
	TYP.
1.78	± 0.15																						0.40 (0.016)														DIMENSIONS IN MILLIMETERS (INCHES).
(0.070	± 0.006)																												0.56 (0.022)

1-134

8-Pin Widebody DIP Package with Gull Wing Surface Mount Option 300 (HCNW2201/11)

						11.15 ± 0.15
					(0.442 ± 0.006)																	PAD LOCATION (FOR REFERENCE ONLY)
																5
	8						7				6
																																						6.15			TYP.
																																						(0.242)
																			9.00 ± 0.15
																			(0.354 ± 0.006)
																																									12.30 ± 0.30
																																									(0.484 ± 0.012)
	1						2				3				4
																																						0.9
															1.3

(0.051)	(0.035)

1.78 ± 0.15

(0.070 ± 0.006)

																			1.55														12.30 ± 0.30
																						(0.061)																	(0.484 ± 0.012)
																							MAX.																	11.00 MAX.
																																			(0.433)
																								4.00				MAX.
																							(0.158)
																																						1.00 ± 0.15
																	2.54											0.75 ± 0.25								(0.039 ± 0.006)														+ 0.076
(0.100)																												(0.030 ± 0.010)																					0.254 - 0.0051
																	BSC																																(0.010	+ 0.003)
DIMENSIONS IN MILLIMETERS (INCHES).																																																		- 0.002)
																																														7° NOM.

LEAD COPLANARITY = 0.10 mm (0.004 INCHES).

Solder Reflow Temperature Profile (HCPL-02XX and Gull Wing Surface Mount Option 300 Parts)

TEMPERATURE – °C

260

240

T = 145°C, 1°C/SEC

220

T = 115°C, 0.3°C/SEC

200

180

160

140

120

100

80

T = 100°C, 1.5°C/SEC

60

40

20

0

0

1

2

3

4

5

6

7

8

9

10

11

12

TIME – MINUTES

Note: Use of nonchlorine activated fluxes is highly recommended.

1-135