Hotpoint ARWDF 129 S, ARWDF 129 Manual

Instructions for use

WASHER-DRYER

NA

English,1

ARWDF 129

!	This symbol reminds you to read this instruction manual.	NA

Contents

Important safety instructions, 2-3

Important safety instructions

Grounding instructions

Safety

Installation instructions, 4-5-6

Unpacking and levelling

Minimum Unstallation Spacing

Connecting Water Inlet

Drainage

Connecting the drain hose

Electrical

Under Sink Method

Technical data

Description of the washer-dryer and starting a wash cycle, 7-8

Control panel Indicator lights Starting a wash cycle

Wash cycles, 9

Table of wash cycles

Special wash cycles

Personalisation, 10-11-12

Setting the temperature

Setting the drying cycle

Functions

Dryer Efficiency

Detergents and laundry, 13

Detergent dispenser drawer

Bleach cycle

Preparing the laundry

Garments requiring special care

Load balancing system

Helpful Hints

Care and maintenance instructions, 14

Cutting off the water or electricity supply Cleaning the washer-dryer

Cleaning the detergent dispenser drawer Caring for the door and drum of your appliance Cleaning the pump

Checking the water inlet hose

Troubleshooting, 15

Service, 16

Warranty, 17-18

1

Important safety instructions

		IMPORTANT SAFETY INSTRUCTIONS
	NA
		WARNING - To reduce	the risk of fire, electrical shock, or
		injury to persons when	using your appliance, follow basic

precautions, including the following:

• Read all instructions before using the appliance.

• Do not wash or dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry cleaning solvents, other flammable, or exlosive substances as they give off vapors that could ignite or explode.

• Do not allow children to play on or in the appliance. Close supervision of children is necessary when the appliance is used near children.

• Before the appliance is removed from service or discarded, remove the door to the washing/drying compartment.

• Do not add gasoline, dry cleaning solvents, or other flammable or explosive substances to the wash water. These substances give off vapors that could ignite or explode.

• Do not install or store this appliance where it will be exposed to the weather.

• Do not tamper with controls.

• Under certain conditions Hydrogen gas may be produced in a hot water system that has not been used for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period, before using the appliance, turn on all hot water faucets and let the water flow from each for several minutes.

This will release any accumulated hydrogen gas. As the gas is flammable do not smoke or use an open flame during this time.

• Turn off water faucets to relieve pressure on hoses and valves and to minimize leakage if a break or rupture occurs.

• Do not reach into the appliance if the tub or drum is moving.

• Do not repair or replace any part of the appliance or attempt any servicing unless specifically recommended in the user-maintenance instructions or in published user-repair instructions that you understand and have the skills to carry out.

• Do not use fabric softeners or product to eliminate static unless recommended by the manufacturer of the fabric softener or product.

• Do not use heat to dry articles containing foam rubber or similarly textured rubber-like materials.

• Good, safe practices and caution MUST be applied when installing, operating, and maintaining any appliance. Follow basic precaution.

•Disconnect power to the washer at the circuit breaker or fuse box, or unplug the machine in an emergency or when servicing required. Have the installer show you and label the proper switch or fuse at the electrical disconnect box.

•The interior of the appliance should be cleaned periodically by qualified service personnel.

•Do not place items exposed to cooking oils in your dryer.

Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire.

•Before loading the washer, make sure the drum is empty.

SAVE THESE INSTRUCTIONS

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistence for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

WARNING - Improper connection of the equipment-groun- ding conductor can result in a electric shock.

Check with a qualified electrician or service representative or personnel if you are in doubt as to whether the appliance is properly gounded.

Do not modify the plug provided with the appliance: if it will not fit outlet, have a proper outlet installed by a qualified electrician.

2

Safety
			NA

CAUTION RISK

OF ELECTRIC !

SHOCK DO

NOT OPEN

CAUTION:

To reduce the risk of electric shock, DO NOT remove cover (or back)/no user servicable parts inside. Refer for servicing to qualified services personnel.

The model number of this product may be found on the back of the unit; the serial number of the label affixed to the back of the unit.

You should note the model and serial numbers of this unit in the space provided. Retain this booklet as a permanent record of your purchase to aid in identification in the event of theft.

MODEL N.

SERIAL N.

!

!

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

The linghtning flash with arrowhead symbol, within an equilateral triagle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitu-

te a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the booklet.

Indesit Company offers to his customers products with the ENERGY STAR Label.

This appliance was tested by UL and conforms with both Canadian and U.S. UL safety requirements C ®UL US LISTED and displays their Mark.

3

Installation instructions

NA ! WARNING-RISK OF FIRE

Clothes dryer installation must be performed by a qualified installer.

Install the clothes dryer according to the manufacturer’s instructions and local codes.

To reduce the risk of severe injury or death, follow all installation instructions.

SAVE THESE INSTRUCTIONS

!This instruction manual should be kept in a safe place for future reference. If the washer-dryer is sold, transferred or moved, make sure that the instruction manual remains with the machine so that the new owner is able to familiarise himself/herself with its operation and features.

!Read these instructions carefully: they contain vital information relating to the safe installation and operation of the appliance.

Unpacking and levelling

Unpacking

1.Remove the washer-dryer from its packaging.

2.Make sure that the washer-dryer has not been damaged during the transportation process. If it has been damaged, contact the retailer and do not proceed any further with the installation process.

3. Remove the 4 protective screws (used during transportation) and the rubber washer with the corresponding spacer, located on the rear part of the appliance (see figure).

4.Close off the holes using the plastic plugs provided.

5.Keep all the parts in a safe place: you will need them again if the washer-dryer needs to be moved to another location.

! Packaging materials should not be used as toys for children.

Levelling

1. Install the washer-dryer on a flat sturdy floor, without resting it up against walls, furniture cabinets or anything else.

2. If the floor is not perfectly level, compensate for any unevenness by tightening or loosening the adjustable front feet (see figure); the angle of inclination, measured in relation to the worktop, must not exceed 2°.

Levelling the machine correctly will provide it with stability, help to avoid vibrations and excessive noise and prevent it from shifting while it is operating.

Minimum Installation Spacing

Recessed Front View

0" *

0" *

	Side View
1"	1" *

This appliance may be installed in a recessed area, closet or alcove. The installation spacing is in inches and is the minimum acceptable.

*Additional spacing should be considered for easy installation, servicing and compliance with local codes and ordinances. Installations must conform with the minimum dimensions indicated.

4

Connecting Water Inlet

If the water pipes you will be connecting to are new or unused, run the water until clear to remove any debris that could clog the water valve screens or valves before connecting the machine. NOTE: Supply shut-off valves should be easily accessible.

Important:

!	Water pressure MUST range wi-
	thin the values indicated on the “Technical Data”
	chart.
1. Screw the cold water fill
hose (C blue connector) onto
the cold water supply until
tight.
2. turn on the cold water		H	C
supply and check for leaks,
tighten if necessary.
3. Screw the hot water fill
hose (H red connector) onto
the hot water supply until tight.
4. Turn on the hot water supply and check for leaks,
tighten if necessary.

Important: Do not use excessive force. Da-

!mage to the couplings can result. The couplings should be tightened by hand; a tool should only be used if a leak occurs.

Drainage

•Standpipe Diameter/Capacity - Needs a 1 ¼” minimum diameter standpipe with a minimum carry-away capacity of 7 gallons per minute.

•Top of Standpipe - Must be between 25” - 34” high from the bottom of the machine.

•Outlet End of Drain Hose (provided with the unit) - Must be at least 20” above the bottom of the washerdryer. An air break must be available at the standpipe to avoid siphoning. No more than 6” of the drain hose should be inserted into the drain pipe to prevent siphoning.

Connecting the drain hose

It is possible for the water to be discharged into a sink, standpipe or drainpipe, but an air break must be available at a min. 20” height to prevent the machine from siphoning

(Fig. 6).

Floor Standpipe	Wall Standpipe	NA
A
	B
A & B = 25" (62 cm) min. / 34" (86 cm) max.		Fig. 4

Standpipe Drain System - Installations require a minimum

1 ¼” (3.2 cm) diameter standpipe with a minimum carry away capacity of 7 gallons (26 liters) per minute.

Wall or Floor Standpipe Drain System - The top of the standpipe must be between 25” (62 cm) - 34” (86 cm) from the bottom of the washer (Fig. 4).

Sink Drain W/ "Y" Branch Tailpiece	Laundry Sink Drain
25" (62 cm) min.
with an air break
	Fig. 5

Sink Drainpipe System - Entry into the sink drain system must be above the trap (Fig. 5). When routing the drain hose through cabinets or walls, use a protective material such as electrical or duct tape to cover sharp edges that could damage the drain hose. Use a suitable clamp to secure the drain hose to the “Y” branch or the disposer. With a sink drainpipe system, you may connect directly:

1)to a disposer by following the manufacturers attachment method.

2)directly to a “Y” branch tail piece (available at most hardware stores).

Important:

!not kinked and that water flow is not restricted.

3)Through the floor to a separate trap. The trap must be vented to prevent siphoning. To provide proper venting, install an Air Gap Kit (available at most hardware stores).

4)To the to the faucet using a Faucet Adapter Kit (available separately). Make sure that the drain hose is

• Use a U-Clamp (provided in your accessories packet) or suitable item to secure the outlet end of the drain hose (pre-installed on the back of your machine).

5

• Insert the outlet end of the drain hose into the standpipe, NA wall or floor drain (Fig. 6). NOTE: The outlet end of the

drain hose MUST be at least 20” (50 cm) above the base of the machine. No more than 6” of the drain hose should be inserted into the drain pipe to prevent siphoning.

•Use a strap, cable tie, or similar item to hold the hose or the U-Clamp in place.

Floor Standpipe

U-Clamp

6" max.

25" (62 cm) min. 34" (86 cm) max.

20" (50 cm) min. with an air break

Fig. 6

Floor Standpipe w/ "Y" Branch Tail Piece

Cable tie
"Y" Tail Piece
				20"		(62 cm) min.
This connection MUST be				34"		(86 cm) max.
before drain trap and at		Standpipe
least 20" (50.8 cm) above
the floor where washer will
be installed.

Fig. 7

Under Sink Method

1. Cut the blocked end of the under sink drainage unit.

2. Fix the hooked end supporta minimum of 620 mm from the floor.

3. Use a hose clip clamp to securely attach the grey drainage hose end to the under sink drainage unit using a hose. clamp

Electrical

•Machine Voltage/Amperage - 120V, 60 Hz, 11 Amp.

•Connection - 3-prong plug with 6’ cord is provided with the machine.

•Circuit/Protector - 3-wire single phase, 120V, 60 Hz, AC, on a separate 15 Amp circuit.

Technical Information

Technical data

	Model	ARWDF 129
		width: 23.4”” (59.5 cm)
	Dimensions	height: 33.24”” - 33.75”” (84.5 - 85.7 cm)
		depth: 22”” (55.9) cm
	Weight	148 lbs
	Minimum Installa-	Sides: 0””
	tion Clearances	Front / Back: 1””
	Capacity	Washing: 2 to 15 lbs. (1 to 7 kg)
		Drying: 2 to 11 lbs. (1 to 5 kg)
	Electrical	Voltage: 120Volts, 11 Amp, 60 Hz
	connections
	Water	Max. Pressure: 0.69 Mpa (6.9 bar), 100 psi
	connections	Min. Pressure: 0.05 Mpa (0.5 bar), 7.2 psi
	Max. Spin speed	up to 1200 RPM

Indesit Company offers to his customers products with the ENERGY STAR Label.

This appliance was tested by UL and	C ®UL US LISTED
conforms with both Canadian and U.S.
UL safety requirements and displays
their Mark.

6

Description of the washer-dryer and starting a wash cycle

Control panel

WASH CYCLE PROGRESS

NA

indicator lights

DISPLAY

ON/OFF

DOOR

TEMPERATURE

button with indicator

LOCKED

button

light

indicator light

									START/PAUSE
	Detergent dispenser drawer
				DRYING			FUNCTION		button with indicator
									light
				button			buttons with
	WASH CYCLE knob						indicator lights
				CHILD LOCK
				button with indicator light

WARNING: To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance.

Detergent dispenser drawer: used to dispense detergents and washing additives (see “Detergents and laundry”).

ON/OFF button with indicator light: switches the machine on and off.

If the indicator light is illuminated, this indicates that the machine is switched on.

WASH CYCLE knob: programmes the wash cycles. During the wash cycle, the knob does not move.

DRYING button: used to set the desired drying programme (see “Personalisation”).

TEMPERATURE button: sets the temperature or the cold wash cycle (see “Personalisation”).

The wash temperatures selections are uniformly distribuited.

DISPLAY: indicates the time remaining for the selected washing/drying cycle and, if a delayed start has been programmed, the time remaining until the start of the wash cycle.

CHILD LOCK button with indicator light: activates or deactivates the control panel lock.

FUNCTION buttons with indicator light: used to select the available functions. The indicator light corresponding to the selected function will remain lit.

WASH CYCLE PROGRESS indicator lights: used to monitor the progress of the wash cycle.

The illuminated indicator light shows which phase is in progress.

DOOR LOCKED indicator light: indicates whether the door may be opened or not (see next page).

START/PAUSE button with indicator light: starts or temporarily interrupts the wash cycles.

N.B. To pause the wash cycle in progress, press this button; the corresponding indicator light will flash orange, while the indicator light for the current wash cycle phase will remain lit in a fixed manner. If the DOOR LOCKED indicator light is switched off, the door may be opened.

To start the wash cycle from the point at which it was interrupted, press this button again.

7

		Indicator lights
	NA
		The indicator lights provide important information.
		This is what they can tell you:
		Wash cycle phase indicator lights
		As the WASH CYCLE knob is rotated, the indicator lights
		illuminate, indicating the stages which will be performed by
		the machine in accordance with the selected wash cycle.
		Once the desired wash cycle has been selected and has
		begun, the indicator lights switch on one by one to indicate
		which phase of the cycle is currently in progress.

Wash

Rinse

		Note: As soon as a drying
	Spin	level or time period has
		been set, this indicator light
	Dry	illuminates to indicate that the
		selected wash cycle will be
	End of wash cycle	followed by a drying phase.

Note:

during the “Drain” phase, the indicator light corresponding to the “Spin” cycle phase will illuminate.

Function buttons and corresponding indicator lights

When a function is selected, the corresponding indicator light will illuminate.

If the selected function is not compatible with the programmed wash cycle, the corresponding indicator light will flash, a sound signal will be emitted and the function will not be activated.

If a function which is incompatible with another function selected previously, only the most recent selection will remain active.

Temperature indicator light

When a temperature value is selected, the corresponding indicator light will illuminate.

Drying indicator light

When a drying value is selected, the corresponding indicator light will illuminate.

Child lock indicator light

To activate the control panel lock, press and hold the button for approximately 2 seconds. When the indicator light is illuminated, the control panel is locked. This means it is possible to prevent wash cycles from being modified accidentally, especially where there are children in the home.

To deactivate the control panel lock, press and hold the button for approximately 2 seconds.

Door locked indicator light

If this indicator light is on, the appliance door is locked to prevent it from being opened accidentally; to avoid any damage, wait for the indicator light to switch off before you open the appliance door.

N.B. If the DELAY TIMER function is activated, the door cannot be opened; pause the machine by pressing the

START/PAUSE button if you wish to open it.

! If the START/PAUSE indicator light (orange) flashes rapidly at the same time as the function indicator light, this indicates a problem has occurred (see “Troubleshooting”).

Starting a wash cycle

1.Switch the washer-dryer on by pressing the ON/OFF button. All indicator lights will switch on for a few seconds, then they will switch off and the START/PAUSE indicator light will pulse.

2.Load the laundry and close the door.

3.Set the WASH CYCLE knob to the desired programme.

4.Set the washing temperature (see “Personalisation”).

5.Set the drying cycle if necessary (see “Personalisation”).

6.Measure out the detergent and washing additives (see “Detergents and laundry”).

7.Select the desired functions.

8.Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit in a fixed manner, in green.

To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle.

9.At the end of the wash cycle the indicator light will switch on. The DOOR LOCKED indicator light will switch off, indicating that the door may be opened. Take out your laundry and leave the appliance door ajar to make sure the drum dries completely. Switch the washer-dryer off by pressing the ON/OFF button.

8

Wash cycles

Table of wash cycles	NA

	cycles				Max.		Max.
	Wash		Description of the wash cycle		temp.		speed		Drying
					(°C)		(rpm)
			Essentials cycles
	1		Cottons Regular: Heavily soiled whites and resistant colours.		Hot		Max		
	2		Cottons Colored: Lightly soiled whites and delicate colours.		Warm		Max		
	3		Permanent Press: Normally soiled synthetics or permanent press labelled		Warm		800		
			garments.
	4		Mixed Load: To refresh lightly soiled garments quickly (not suitable for wool,		Warm		800		
			silk and clothes which require washing by hand).
	5		Quick Wash&Dry		Warm		Max		
			Special wash cycles
	6		Bright White: Heavily soiled whites and resistant colours.		Warm		Max		
	7		Active Wear		Warm		600		-
	8		Lightly Soiled 15 min.: To refresh lightly soiled garments quickly		Warm		800		
			(not suitable for wool, silk and clothes which require washing by hand)
	9		Delicate: Lightly soiled delicates colours.		Warm		800		
	10		Wool: for wool, cashmere, etc.		Warm		800		
			Drying
	11		Cottons						
					-		-
	12		Permanent Press		-		-		
	13		Wool		-		-		
			Partials wash cycles
	A		Rinse				Max		
					-
	B		Spin		-		Max		
	C		Drain no spin		-		-		-

	Detergents					Max	Cycle
						load	dura-
				Fabric
Bleach		Wash				(lb)	tion
				softener
-						Max
-						Max	display.the
-						6.6
-						6.6
-						2.20	on
							checked
						Max
							be
-						6.6
							can
-						3.30	cycles
-						6.6	wash
-						3.30
-		-		-		11	of the
							duration
-		-		-		6.6
-		-		-		2.20	The
-						Max
		-
-		-		-		Max
-		-		-		Max

Special wash cycles

Permanent (wash cycle 3) Press this cycle has less mechanical agitation and spinning speed designed to reduce wrinkles.

Mixed Load (wash cycle 4) this wash cycle was designed to wash lightly soiled garments quickly: it lasts just 30 minutes and therefore saves both energy and time. By selecting this wash cycle (4 at WARM temperature), it is possible to wash different fabrics together (except for wool and silk items), with a maximum load of 6.6 lb - (3 kg).

Quick Wash & Dry (wash cycle 5) was designed to wash and dry lightly soiled garments quickly. This cycle may be used to wash and dry a laundry load of up to 2.20 lb - (1 kg) in just 60 minutes.

To achieve optimum results, use liquid detergent and pre-treat cuffs, collars and stains.

Bright White (wash cycle 6) Use this cycle when bleaching with hypoclorite based products.

Pour the bleach, the detergent and the additives into the relevant compartments (see paragraph entitled “Detergent dispenser drawer”).

Active wear (wash cycle 7) is for washing lightly soiled sports clothing fabrics (tracksuits, shorts, etc.); for best results, we recommend not exceeding the maximum load indicated in the “Table of wash cycles”. We recommend using a liquid detergent and dosage suitable for a half-load.

Lightly Soiled 15 min. (wash cycle 8) this wash cycle was designed to wash lightly soiled garments quickly: it lasts just 15 minutes and therefore saves both energy and time. By selecting this wash cycle (8 at WARM temperature), it is possible to wash different fabrics together (except for wool and silk items), with a maximum load of 3.30 lb - (1.5 kg).

For this cycle we recommend pretreating stains, shirt necks and wrists with specific antistain products.

9

Personalisation

		Setting the temperature
	NA
		By pressing the TEMPERATURE button to set the wash temperature. (See Table of wash cycles) Wash temperature can be
		set selecting			, “Cold”, “Warm”, “Hot” or 2 in-between positions which correspond to intermediate levels of water tempe-
		rature (example: the position between “cold” and “warm” is lukewarm). See below for the indication in °C and °F for each
		temperature position.
		The available selections are:
			•		Tap water
			•	Cold	15	°C/ 59 °F
			•		20	°C/ 68	°F
			•	Warm	30	°C/ 86	°F
			•		40	°C/ 104 °F
			•	Hot	57	°C / 134 °F

	Setting the drying cycle
	The desired drying cycle type may be set by pressing the	Table of Drying times (guideline values)
	DRYING button once or several times. Two options are
		Fabric		Max.	Cupboard	Iron
	available:		Load type
		type		load (lb)	dry	dry
	A - Based on time: from 40 to 180 minutes.
	B - Based on the how damp the clothes are once they have		Clothing of different
	been dried:	Cotton		11.02	180	160
			sizes, Terry towels
	Iron dry : slightly damp clothes, easy to iron.
	Cupboard dry : very dry clothes, recommended for towelling	Synthe-	Sheets, Shirts, Pyjamas,	6.6	180	160
	and bathrobes.	tics	socks, etc.
	If your laundry load to be washed and dried is much greater	Wool	Knitwear, Pullovers, etc.	3.30	150	130
	than the maximum stated load (see adjacent table), perform
	the wash cycle, and when the cycle is complete, divide the
	garments into groups and put some of them back in the

drum. At this point, follow the instructions provided for a “Drying only” cycle. Repeat this procedure for the remainder of the load.

N.B.: when the drying is complete there is a cooling period, even though the DRYING button is in the 0 position.

Drying only

Turn the WASH CYCLE knob to one of the drying settings (11-12-13) according to the type of fabric, then select the desired drying duration using the DRYING button.

Functions

The various wash functions available with this washer-dryer will help to achieve the desired results, each time. To activate the functions:

1.Press the button corresponding to the desired function;

2.the function is enabled when the corresponding indicator light is illuminated.

Note: If the indicator light flashes rapidly, this signals that this particular function may not be selected in conjunction with the selected wash cycle.

Delay timer

To set a delayed start for the selected wash cycle, press the button repeatedly until the desired delay time is displayed (this may be between 1 hour and 24 hours).

To disable the function press the button until the text is displayed.

N.B. Once you have pressed the START/PAUSE button, the delay time may only be decreased if you wish to modify it. ! This option is enabled with all programmes.

Super Wash

Because a greater quantity of water is used in the initial phase of the cycle, and because of the increased cycle duration, this function offers a high-performance wash.

! This function may not be used in conjunction with wash cycles 4, 5, 8, 10, 11, 12, 13, A, B, C.

10

Extra rinse
			NA
By selecting this function, the efficiency of the rinse is increased and optimal detergent removal is guaranteed. It is particularly
useful for sensitive skin.

! This function may not be used in conjunction with wash cycles 4, 5, 8, 11, 12, 13, B, C.

Spin speed

By selecting this function it is possible to reduce the spin speed.

! This function may not be used in conjunction with wash cycles 1, 2, 5, 11, 12, 13, C.

Note: For the first two Programmes (Cottons Regular and Cottons Colored) the garments will be spun at maximum speed. This allows to get the most from the spinning phase and reduce time and energy needed for the drying.

11

NA

Dryer Efficiency

Your washer dryer operates on 120 volts and has a 1,200 watt dryer. It will take a longer time to dry clothes than a traditional dryer (which operates on 220 volts, 5,000 watts).

However, with the following tips, you can increase the efficiency of the dryer.

1. DOOR REMAINS LOCKED DURING DRYING: The door is electronically kept locked drying cycle, with the Mode+Door Lock light on. This prevents any starting abd shutting the heater, which in turn conserves energy by trapping the heat.

2. FABRIC SOFTNER: When the Wash and Dry cycles are set to run consecutively, the preheat function comes on automatically. In this, the heater is turned on during the last spin cycle of the wash program. In the Regular Wash program, the clothes will be getting sun at 1,200 rpm, while hot air from the dryer will be entering the drum at the same time. While

centrifugal force causes clothes to stick to the sides of the drum, the hot air will “bake) them to sides. It may take 30 minutes or more for the clothes to unstick and fall into the drum. USING LIQUID FABRIC SOFTNER WILL CAUSE

THE CLOTHEST UNSTICK IMMEDIATELY. THIS HELPS DRY CLOTHES FASTER AND CAUSES LESS WRINKLES.

3. OVERLOADING: The drum has a capacity of 12 lbs. While this is the largest drum available on any combination washer-dryer. The drum should not be overloaded. With too many clothes, airflow is reduced, increasing drying time. A maximum of 2/3 of the drum full of clothes is raccomanded for ideal drying.

4. OVER DRYING: This machine uses a condensing dryer. In this cold water is used to condense the moisture from the hot air. Since there is no external exhaust system, the moisture remains in the machine. Frequently, when it seems the clothes are damp, it is actually the remaining moisture (like dew). Take clothes out and within a few minutes they will be dry. Do not overdry the clothes.

5. USE LOW SUDSING DETERGENT: By using low sudsing detergent, you are preventing suds from entering the condensing chamber. When suds enter the condensing chamber, lint particles can clog up the chamber and the fan blower. Over time, this reduces drying efficiency and may require the fan blower (impeller) to be cleaned.

Your new appliance is carefully engineered product. Many times what appears to be a reason to call for service, requires nothing more than a simple adjustment you can easily make in your own home.

You will be charged for a service call while the appliance is in warranty if the problem is not caused by defective product workmanship or materials covered by this warranty.

To avoid a charge for an unnecessary service call, and before calling a serviceman, please refer to the troubleshooting section for situations that you can remedy. This section is included on pages 16-17 of this Use and Care Book.

Your Washer-Dryer is front loading, with an extra large door opening for easier access. It has 9 wash cycles in addition to extra rinse and pre wash cycles.

You will obviously want to obtain the best possible wash. By reading and following the instructions in this booklet you will achieve excellent results.

Please, ensure that the instructions are followed. If you should need any further advice or assistance, please, contact the dealer where your machine was purchased.

This appliance is an automatic washer with a capacity of up to:

15 lbs (6,8 kg)

12

Detergents and laundry

Detergent dispenser drawer

Good washing results also depend on the correct dose of detergent: adding too much detergent will not necessarily result in a more efficient wash, and may in fact cause build up on the inside of your appliance and contribute to environmental pollution.

! Do not use hand washing detergents because these create too much foam.

MAX	3
2	1

Open the detergent dispenser drawer and pour in the detergent or washing additive, as follows.

compartment 1: Detergent for the wash cycle (powder or liquid)

Liquid detergent should only be poured in immediately prior to the start of wash cycle.

compartment 2: Additives (fabric softeners, etc.)

The fabric softener should not overflow the grid. extra compartment 3: Bleach

Bleach cycle

Bleaching may only be performed in conjunction with wash cycles 6. Pour the bleach into extra compartment 3; pour the detergent and softener into the corresponding compartments, then select one of the abovementioned wash cycles.

This option is recommended only for very soiled cotton garments.

Preparing the laundry

•Divide the laundry according to:

-the type of fabric/the symbol on the label.

-the colours: separate coloured garments from whites

•Empty all garment pockets and check the buttons.

•Do not exceed the listed values, which refer to the weight of the laundry when dry:

Durable fabrics: max. 15 lb - (7 kg)

Synthetic fabrics: max. 6.6 lb - (3 kg)

Delicate fabrics: max. 4.4 lb - (2 kg) Wool: max. 3.30 lb - (1,5 kg)

How much does your laundry weigh?

1 sheet 14-17 oz - (400-500 g)

1 pillow case 5-7 oz - (150-200 g) 1 tablecloth 14-17 oz - (400-500 g)

1 bathrobe 31-42 oz - (900-1200 g) 1 towel 5-8 oz - (150-250 g)

Garments requiring special care	NA

Wool: Ariston is the only washer-dryer manufacturer to have been awarded the prestigious Woolmark Platinum Care endorsement (M.0508) by the Woolmark Company, which means that all woollen garments may be washed in the washerdryer, even those which state “hand wash only” on the label. Wash cycle 10 therefore offers complete peace of mind when washing woollen garments in the washer-dryer (max. load 3.30 lb - 1,5 kg) and guarantees optimal performance.

Load balancing system

Before every spin cycle, to avoid excessive vibrations and to distribute the load in a uniform manner, the drum rotates continuously at a speed which is slightly greater than the washing rotation speed. If, after several attempts, the load is not balanced correctly, the machine spins at a reduced spin speed. If the load is excessively unbalanced, the washerdryer performs the distribution process instead of spinning. To encourage improved load distribution and balance, we recommend small and large garments are mixed in the load.

Helpful Hints

Your washer Dryer features three different speeds during the wash cycle. During the Cotton cycle the drum spins at 1,200 or 800 rpm. During Permanent Press the drum spins at 850 rpm. During delicates, the drum spins at 500 rpm. When Drying heavy cotton articles, such as bath towels or jeans, be sure the

“Regular” washer setting is selected. The faster spinning will extract more water from these highly absorment fabrics and reduce the degree of dampness as the machine goes into the drying mode. This will cut down on your drying time.

Use Liquid Fabric Softener. Fill the softener compartment up to the level marked. Using fabric softner fluffs out clothes immediately after tha wash cycle. This helps speed drying time and reduce wrinkles.

This washer Dryer is a 120 Volt machine, so the heating element requires more time to achieve full heat than a larger

220 Volt unit requires. The heating element will take about 10 minutes to reach full heat.

To dry your laundry, the Washer Dryer blows heated air into the rotating drum. As the drum tumbles your laundry, the warm air dries it. If the drum is overfilled with laundry, the air is not allowed to circulate and clothes will not dry properly.

Use Low sudsing Detergent. This is recommended for all front loading washers. It ensures there is no over sudsing, which may reduce the performance of your machine. Also, this prevents damage to your machine which may be caused by excess suds entering the condensing chamber and clogging the fan blower mechanism with lint.

When sorting laundry always take into consideration the quantity and type of fabric contained in the load. Highly absorbent fabrics such as those used in towels or jeans will

abosorb more water and become very heavy when saturated. If you notice that your clothes are taking longer than usual to dry may be overloading the machine, or washing too many highly absorbent articles for a single load.

13

Care and maintenance instructions

Cutting off the water and electricity NA supplies

•Turn off the water tap after every wash cycle. This will limit wear on the hydraulic system inside the washer-dryer and help to prevent leaks.

•Unplug the washer-dryer when cleaning it and during all maintenance work.

Cleaning the washer-dryer

The outer parts and rubber components of the appliance can be cleaned using a soft cloth soaked in lukewarm soapy water. Do not use solvents or abrasives.

Cleaning the detergent dispenser drawer

1

2

Remove the dispenser by raising it and pulling it out (see figure).

Wash it under running water; this operation should be repeated frequently.

Caring for the door and drum of your appliance

•Always leave the porthole door ajar in order to prevent unpleasant odours from forming.

Cleaning the pump

The washer-dryer is fitted with a self-cleaning pump which does not require any maintenance. Sometimes, small items (such as coins or buttons) may fall into the pre-chamber which protects the pump, situated in its bottom part.

! Make sure the wash cycle has finished and unplug the appliance.

To access the pre-chamber:

1. using a screwdriver, remove the cover panel on the lower front part of the washer-dryer (see figure);

2. unscrew the lid by rotating it anti-clockwise (see figure): a little water may trickle out. This is perfectly normal;

3.clean the inside thoroughly;

4.screw the lid back on;

5.reposition the panel, making sure the hooks are securely in place before you push it onto the appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If there are any cracks, it should be replaced immediately: during the wash cycles, water pressure is very strong and a cracked hose could easily split open.

! Never use second-hand hoses.

14

Troubleshooting

Your washer-dryer could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure that
			NA
the problem cannot be not solved easily using the following list.

Problem:

The washer-dryer does not switch on.

The wash cycle does not start.

The washer-dryer does not take in water (the indicator light for the first wash cycle stage flashes rapidly).

The washer-dryer continuously takes in and drains water.

The washer-dryer does not drain or spin.

The washer-dryer vibrates a lot during the spin cycle.

The washer-dryer leaks.

The START/PAUSE indicator light (orange) and the function indicator lights flash rapidly.

There is too much foam.

The washer-dryer does not dry.

Possible causes / Solutions:

•The appliance is not plugged into the socket fully, or is not making contact.

•There is no power in the house.

•The washer-dryer door is not closed properly.

•The ON/OFF button has not been pressed.

•The START/PAUSE button has not been pressed.

•The water tap has not been opened.

•A delayed start has been set (using the Delay Timer, see “Personalisation”).

•The water inlet hose is not connected to the tap.

•The hose is bent.

•The water tap has not been opened.

•There is no water supply in the house.

•The pressure is too low.

•The START/PAUSE button has not been pressed.

•The drain hose is not fitted at a height between 65 and 100 cm from the floor

(see “Installation”).

•The free end of the hose is under water (see “Installation”).

•The wall drainage system is not fitted with a breather pipe.

If the problem persists even after these checks, turn off the water tap, switch the appliance off and contact the Assistance Service. If the dwelling is on one of the upper floors of a building, there may be problems relating to water drainage, causing the washer-dryer to fill with water and drain continuously. Special antidraining valves are available in shops and help to avoid this inconvenience.

•The wash cycle does not include draining: some wash cycles require the drain phase to be started manually.

•The drain hose is bent (see “Installation”).

•The drainage duct is clogged.

•The drum was not unlocked correctly during installation (see “Installation”).

•The washer-dryer is not level (see “Installation”).

•The washer-dryer is trapped between cabinets and walls (see “Installation”).

•The water inlet hose is not screwed on properly (see “Installation”).

•The detergent dispenser drawer is blocked (for cleaning instructions, see “Care and maintenance”).

•The drain hose is not fixed properly (see “Installation”).

•Switch off the machine and unplug it, wait for approximately 1 minute and then switch it back on again.

If the problem persists, contact the Technical Assistance Service.

•The detergent is not suitable for machine washing (it should display the text

“for washer-dryers” or “hand and machine wash”, or the like).

•Too much detergent was used.

•The appliance is not plugged into the socket, or not enough to make contact.

•There has been a power failure.

•The appliance door is not shut properly.

•A delayed start has been set (using the Delay Timer, see “Personalisation”).

•Button DRYING is in the 0 position.

15

Service

			Before calling for Assistance:
	NA
			• Check whether you can solve the problem alone (see “Troubleshooting”);
			• Restart the programme to check whether the problem has been solved;
			• If this is not the case, contact an authorised Technical Assistance Centre using the telephone number provided on the
			guarantee certificate.
			! Always request the assistance of authorised technicians.

Have the following information to hand:

•the type of problem;

•the appliance model (Mod.);

•the serial number (S/N).

This information can be found on the data plate applied to the rear of the washer-dryer, and can also be found on the front of the appliance by opening the door.

16

Warranty

ARISTON ONE-YEAR LIMITED WARRANTY
			NA
(USA & CANADA ONLY)

WHO IS COVERED BY THIS WARRANTY

This limited one-year warranty (“Warranty”) is given only to the original end-use/retail purchaser (the “First Using

Purchaser”) of the accompanying Ariston product(s) (the “Ariston Product”).

If you purchased this Ariston Product from someone other than an authorized Ariston reseller/dealer in the United States or Canada, or if the Ariston Product was used (including but not limited to floor models or refurbished products) prior to your purchase, then you are not the First Using Purchaser and the Ariston Product that you purchased is not covered by this Warranty. This Warranty is not transferable.

WHAT IS COVERED BY THIS WARRANTY

Ariston will repair or replace any part of the Ariston Product which fails due to a defect in materials or workmanship when used under normal home-use conditions. Ariston will also provide, free of charge, all labor and related services to repair or replace the defective part.

This Warranty applies only to Ariston Products purchased and used in the United States or Canada. Subject to the exclusions below, for Ariston Products purchased in, but used outside, the United States or Canada, this Warranty covers only warranty service within the United States or Canada (and does not include shipping outside the United States or Canada).

LENGTH OF THE WARRANTY

This Warranty runs for a period of one (1) year from the date of the original purchase by the First Using Purchaser. Please note that a copy of your original purchase receipt showing the purchase date and the vendor’s name and address are required to obtain service under this Warranty. For the purposes of determining the applicable warranty period, please note that any and all replaced or repaired parts shall assume the identity of the original.

WHAT IS NOT COVERED BY THE WARRANTY (EXCLUSIONS)

This Warranty does not cover:

1.Improper installation, delivery, maintenance and/or improper operation of the Ariston Product.

2.Damage caused if the Ariston Product has not been used in compliance with the electricity or gas supply specifications printed on the rating plate.

3.Failure of or damage to the Ariston Product if it is altered, abused, misused, or used for other than the intended purpose, or if it is used commercially.

4.Service trips to your home to provide instructions on the use of your Ariston Product.

5.Replacement of house fuses or correction of the plumbing or electric wiring in your home.

6.Damage caused by neglect, accident, fire, floods or acts of God.

7.Physical Damage to the appearance of your Ariston

Product including, without limitation, scratches, rust, dents, warping, peeling and the like.

8.Damage caused by transportation.

9.Replacement of any consumable or degradable item or accessory including, but not limited to: plugs, cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters, or replacement of any removable parts made of glass or plastic.

10.Damage caused after delivery.

11.Water damage of any kind.

12.An Ariston Product not accessible to provide required service.

13.Problems arising from other than defects in materials or workmanship.

14.Travel time when installed in a recreational vehicle or marine application.

This Warranty is void if the Ariston Product is altered, serviced, maintained, dismantled, or otherwise interfered with by any person who is not authorized by Ariston.

15.Non-standard labor when installed in a marine application.

16.Water leaks of any kind.

TO THE EXTENT PERMITTED BY LAW, THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, WRITTEN

OR ORAL, WHETHER EXPRESSED BY AFFIRMATION, PROMISE, DESCRIPTION, DRAWING, MODEL OR SAMPLE. ANY AND ALL WARRANTIES OTHER THAN THIS ONE, WHETHER EXPRESS OR IMPLIED, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED. IMPLIED WARRANTIES INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS THAT CANNOT BE EXCLUDED BY LAW, SHALL BE LIMITED TO THE SAME DURATION AS THIS WARRANTY. EXCEPT FOR THAT REPAIR OR REPLACEMENT AS DESCRIBED ABOVE, ARISTON SHALL NOT BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR SPECIFIC RELIEF.

Some States and Provinces do not allow the exclusion or limitation of incidental or consequential damages and/or implied warranties, so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights and you may also have other legal rights which vary from State to State or Province to Province.

17