HOTPOINT AQ9D692 User Manual

Instructions for installation and use

WASHING MACHINE

EN		FR		NL
English,1		Français,13		Nederlands,25

Contents	EN

Installation, 2-3

Unpacking and levelling

Connecting the electricity and water supplies

Technical data

AQUALTIS

AQ9D 692 U

Description of the machine, 4-5

Touch control panel

Running a wash cycle, 6

Wash cycles and options, 7

Table of wash cycles Wash options

Detergents and laundry, 8

Detergent

Preparing the laundry Washing recommendations

Precautions and advice, 9

General safety

Load balancing system Disposal

Opening the porthole door manually

Care and maintenance, 10

Cutting off the water and electricity supplies Cleaning the machine

Cleaning the detergent dispenser drawer Caring for your appliance drum Cleaning the pump

Checking the water inlet hose

Trouble shooting, 11

Assistance, 12

1

Installation

! This instruction manual should be kept in a safe place EN for future reference. If the washing machine is sold, given

away or moved, please ensure the manual is kept with the machine, so that the new owner may benefit from the advice contained within it.

!Read these instructions carefully: they contain vital information relating to the safe installation and operation of the appliance.

!Inside the pack containing this manual, you will also find the guarantee and all the details necessary for installation.

Unpacking and levelling

Unpacking

1. Once you have removed all the packaging from the washing machine, make sure it has not been damaged during transportation.

If it has been damaged, contact the retailer and do not proceed any further with the installation process.

2. Remove the 4 protective screws (used during transportation) and the corresponding spacer, located on the rear part of the appliance (see figure).

3.Close off the holes using the plastic plugs supplied in the pack.

4.Keep all the parts in a safe place; they will be needed again if the washing machine is moved to another location, to prevent the inside of the appliance being damaged.

! Packaging materials should not be used as toys for children.

Levelling

1. Place the washing machine on a flat sturdy floor, without resting it up against walls or cabinets.

2. If the floor is uneven, the front feet of the machine may be adjusted until

it reaches a horizontal position (the angle of inclination must not exceed 2 degrees).

!If the appliance is levelled correctly, it will be more stable and much less likely to cause vibrations and noise while it is operating, particularly during the spin cycle.

!If it is placed on carpet or a rug, adjust the feet in such a way as to allow a sufficient ventilation space underneath the washing machine.

Connecting the electricity and water supplies

Connecting the water inlet hose

! Before connecting the inlet hose to the water supply, run the water until it is perfectly clear.

1. Connect the inlet hose to the machine by screwing it onto the cold water inlet of the appliance, which is situated on the top righthand side of the rear part of the appliance (see figure).

2. Connect the inlet hose by screwing it to a cold water tab using a 3/4 gas threaded connection (see figure).

3. Make sure that the hose is not folded over or bent.

!The water pressure at the tap must fall within the values indicated in the Technical data table (see next page).

!If the inlet hose is not long enough, contact a specialised shop or an authorised technician.

!Never use second-hand or old inlet hoses; use the products supplied with the machine.

2

Connecting the drain hose

65 - 100 cm

Connect the drain hose to drain duct piping or a wall drain located between 65 and 100 cm above the floor, making sure it is not bent at all.

Alternatively, rest the drain hose on the side of a washbasin or bathtub,

fastening the duct supplied to the tap (see figure).

The free end of the hose should not be underwater.

! Do not use extension cords or multiple sockets.

EN

!The cable should not be bent or compressed.

!The power supply cable and plug must only be replaced by authorised technicians.

Warning! The company shall not be held responsible in the event that these regulations are not respected.

! We advise against the use of hose extensions; if it is absolutely necessary, the extension must have the same diameter as the original hose and must not exceed 150 cm in length.

Electrical connections

Before plugging the appliance into the electricity socket, make sure that:

•the socket is earthed and complies with all applicable laws;

•the socket is able to withstand the maximum power load of the appliance as indicated in the Technical data table

(see opposite);

•the power supply voltage falls within the values indicated in the Technical data table (see opposite);

•the socket is compatible with the plug of the appliance.

If this is not the case, have the socket or the plug replaced.

!The machine must not be installed outdoors, even in covered areas. It is extremely dangerous to leave the appliance exposed to rain, storms and other weather conditions.

!The mains socket must remain within easy reach after the washing machine has been installed.

Technical data

Model	AQ9D 692 U
	width 59.5 cm
Dimensions	height 85 cm
	depth 64,5 cm
Capacity	from 1 to 9 kg
Electrical	please refer to the technical data plate
connections	fixed to the machine
	maximum pressure 1 MPa (10 bar)
Water connections	minimum pressure 0.05 MPa (0.5 bar)
	drum capacity 62 litres

	Spin speed	up to 1600 rotations per minute
	Energy rated
	programmes	programme		; temperature 60°C;
	according to
		using a load of 9 kg.
	regulation
	EN 60456
		This appliance conforms to the following
		EC Directives:

-2004/108/EC (Electromagnetic Compatibility)

-2006/95/EC (Low Voltage)

- 2002/96/EC

3

Description of the machine

EN		CONTROL
		PANEL
	PORTHOLE DOOR

PORTHOLE DOOR

HANDLE

KICK STRIP

ADJUSTABLE FEET

PORTHOLE DOOR

Always use the handle to open the porthole door (see figure).

DETERGENT DISPENSER DRAWER

The detergent dispenser drawer is located inside the machine and can be accessed by opening the door.

For more information on detergent measures, please refer to the chapter entitled

“Detergents and laundry”.

	1. pre-wash compartment:
	use powder detergent.
	2. main wash compartment:
1	use powder or liquid
2	detergent. If using the
	latter type of detergent, we
	recommend it is poured
	into the drawer immediately
	before you start the washing
	machine.

washing additives compartment: for fabric softener or liquid additives. We recommend that the maximum level indicated by the grille is not exceeded, and that concentrated fabric softeners are diluted.

TOUCH CONTROL PANEL

To adjust the settings, gently press the icon inside the

sensitive (touch control) area as illustrated in the figure.

Standby mode

This washing machine, in compliance with new energy saving regulations, is fitted with an automatic standby system which is enabled after about 30 minutes if no activity is detected. Press the ON-OFF button briefly and wait for the machine to start up again.

4

Touch control panel							START/PAUSE button
					SPIN		with indicator light			WASH
WASH CYCLE					button
		M2		M1			ECO			CYCLE
SELECTOR knob					TEMPERATURE		indicator light			PHASE
					button					icons

DISPLAY

Button with ON/OFF								CONTROL PANEL
				OPTION				LOCK button with
	M3				DELAYED START
indicator light
				buttons				indicator light
					button
							DOOR LOCKED indicator light

Button with ON/OFF indicator light: press this briefly to switch the machine on or off. The green indicator light indicates that the machine is switched on. To switch off the

washing machine during the wash cycle, press and hold the button for approximately 3 seconds; if the button is pressed briefly or accidentally the machine will not switch off. If the machine is switched off during a wash cycle, this wash cycle will be cancelled.

WASH CYCLE SELECTOR knob: may be turned in either direction. To select the most suitable wash cycle, please refer to the “Table of wash cycles”.

The knob will not move during the wash cycle.

M1-M2-M3 buttons: press and hold one of the buttons to store a cycle with your own set preferences in the memory of the machine. To recall a previously-stored cycle, press the corresponding button.

TEMPERATURE button: press to modify or exclude the temperature setting; the value selected will appear on the display above (see “Running a wash cycle”).

SPIN CYCLE button: press to modify or exclude the spin cycle; the value selected will appear on the display above (see “Running a wash cycle”).

DELAYED START button: press to set a delayed start for the selected wash cycle; the set delay time will appear on the display above (see “Running a wash cycle”).

OPTION buttons: press to select the available options. The indicator light corresponding to the selected option will remain lit (see “Running a wash cycle”).

WASH CYCLE PHASE icons: these illuminate to indicate the progress of the wash cycle (Wash – Rinse – Spin

– Drain ). The text lights up when the cycle is complete.

START/PAUSE button with indicator light: when the green indicator light flashes slowly, press the button to start a wash cycle. Once the cycle has begun the indicator light will remain lit in a fixed manner. To pause the wash cycle, press the button again; the indicator light will flash in an orange colour. If the

“Door locked” indicator light is switched off, the door may be opened. To start the wash cycle from the point at which it was interrupted, press the button again.

DOOR LOCKED indicator light: indicates that the porthole door is locked. To open the door, pause the wash cycle (see “Running a wash cycle”).

CONTROL PANEL LOCK button with indicator light: to activate or deactivate the control panel lock, press and hold the button for approximately 2 seconds. when the indicator light is illuminated, the control panel is locked. This means

it is possible to prevent wash cycles from being modified accidentally, especially where there are children in the home.

ECO indicator light: the icon lights up when, after altering the washing parameters, an energy saving of at least 10%

is made. Furthermore, before the machine enters “Standby” mode, the icon will light up for a few seconds; when the machine is switched off the estimated energy saving will be around the 80% mark.

CHANGE LANGUAGE

The first time the machine is switched on, the first language will flash on the display. The ““, “OK” and “V” symbols will appear on the display, in line with the 3 buttons on the righthand side. The languages change automatically every 3”; alternatively, they can be changed by pressing the buttons next to the ““ and “V” symbols. Use the “OK” button to confirm the language, which will be set after 2”. If no buttons are pressed, the automatic language change will begin again after 30”.

The language may only be changed while the machine is switched off.

Press and hold the temperature +spin +delayed start

buttons for 5’’; a short beep sounds and the set language flashes on the display. Press the buttons next to the ““ and “V” symbols to change the language. Use the button next to the “OK” symbol to confirm the language, which will be set after 2”. If no buttons are pressed, the language set previously will be displayed after 30”.

Switch on the machine.

5

Running a wash cycle

WARNING: before you use the washing machine for the first EN time, run a wash cycle with detergent and no laundry, using

the 90° cottons cycle without pre-wash.

1.SWITCH THE MACHINE ON. Press the button. All the indicator lights will illuminate for 1 second and the text AQUALTIS will appear on the display; the indicator

light corresponding to the button will then remain lit in a constant manner and the START/PAUSE indicator light will flash.

2.SELECT THE PROGRAMME. Turn the PROGRAMME KNOB left or right, until the required programme has been selected; the name of the programme will appear on the display. A temperature and spin speed is set for each programme; these may be adjusted. The cycle duration will also appear on the display.

3.LOAD THE LAUNDRY. Open the porthole door. Load the laundry, making sure you do not exceed the maximum load value indicated in the table of wash cycles on the following page.

4.MEASURE OUT THE DETERGENT. Pull out the detergent dispenser drawer and pour the detergent into the relevant compartments as described in “Description of the machine”.

5.CLOSE THE PORTHOLE DOOR.

6.CUSTOMISE THE WASH CYCLE. Use the relevant buttons on the control panel:

Modify the temperature and/or spin speed.

The machine automatically displays the maximum temperature and spin speed values set for the selected cycle, or the most recently-used settings if they are compatible with the selected cycle. The temperature

can be decreased by pressing the button, until the cold wash “OFF” setting is reached. The spin speed may

be progressively reduced by pressing the button, until it is completely excluded “OFF”. If these buttons are pressed again, the maximum values are restored. ! Exception: if the “Cottons” programme is selected, the temperature can be increased up to a value of 90°C.

Setting a delayed start.

To set a delayed start for the selected cycle, press the corresponding button repeatedly until the required delay period has been reached. During the setting procedure, the delay period and the text “Starts in:” will be displayed, along with the flashing symbol. After the delayed start has been set, the symbol will remain fixed on the display, which will also indicate the duration of the selected cycle with the text “Ends in:” and the cycle duration. Press the DELAYED START button just once to display the delay time set previously.

After the countdown has begun, the display will show the text “Starts in:” and the delay period. Once the set delay time has elapsed, the machine will begin its cycle and the display will show “Ends in:” and the time remaining until the end of the cycle. To remove the delayed start option, press the button until the display shows the text OFF; the

symbol will disappear.

Modify the cycle settings.

•Press the button to activate the option; the name of the option will then appear on the display and the corresponding indicator light will illuminate.

•Press the button again to deactivate the option; the name of the option will then appear on the display followed by the text OFF, and the corresponding indicator light will switch off.

!If the selected option is not compatible with the selected wash cycle, this incompatibility will be signalled by the flashing of the indicator light and a sound alert (3 beeps); the option will not be activated.

!If the selected option is not compatible with another option that has been selected previously, the indicator light corresponding to the first option selected will flash and only the second option will be activated; the indicator light corresponding to the button will remain lit in a constant manner.

!The options may affect the recommended load value

and/or the duration of the cycle.

7.START THE PROGRAMME. Press the START/PAUSE button. The corresponding indicator light remains lit in

a fixed manner and the porthole door locks (the DOOR LOCKED indicator light illuminates). The icons corresponding to the wash cycle phases will light up during the cycle to indicate which phase is currently in progress.

To change a wash cycle once it has already started, pause the washing machine by pressing the START/ PAUSE button; then select the desired cycle and press the START/PAUSE button again.

To open the door during a wash cycle, press the START/ PAUSE button; if the DOOR LOCKED indicator

light is switched off you may open the door. Press the START/PAUSE button again to restart the wash cycle from the point at which it was interrupted.

8.THE END OF THE WASH CYCLE. This is indicated by the illuminated text END. The porthole door may be opened immediately. If the START/PAUSE indicator light is flashing, press the button to end the cycle. Open the door, unload the laundry and switch off the machine.

!If you wish to cancel a cycle which has already begun,

press and hold the button until the cycle stops and the machine switches off.

Bag for quilts, curtains and delicate garments

The Aqualtis washing machine makes it easier for you to wash even the most valuable and delicate garments in complete confidence thanks to the special bag which protects the laundry (this is supplied with the machine).

We recommend that the bag is used every time you wash quilts and padded items with an outer layer made using synthetic material.

6

Wash cycles and options

Table of wash cycles

					Max. temp.	Max.	Detergent and additives			Max.
	Icon			Description of the wash cycle		speed	Deter-	Deter-	Fabric	load
					(°C)
							gent for	gent for
						(rpm)				(kg)
									softener
							prewash	wash
				Cottons wash cycles
				Cottons with pre-wash	90°	1600				9
				(Add detergent to the relevant compartment).
				Cotton (1): heavily soiled whites and resistant colours.	60°	1600	-			9
					(Max. 90°C)
				Cotton (2): heavily soiled whites and delicate colours.	40°	1600	-			9
				Coloured Cotton (3)	40°	1600	-			9
				Shirts	40°	600	-			2
				Jeans	40°	800	-			4
				Special programmes
				Baby: heavily soiled delicate colours	40°	800	-			4
				Durable Synthetics	60°	800	-			4
				** Steam Refresh (see next page).	-	-	-	-	-	1,5
				"Bed & Bath"" for bedlinen and towels.	60°	1600	-			9
				Duvets: for down-stuffed garments.	30°	1200	-			3,5
				Silk: for garments in silk and viscose, lingerie.	30°	0	-			2
				Wool: for wool, cashmere, etc.	40°	600	-			2
				Mix 30': to refresh lightly soiled garments quickly (not suitable	30°	800	-			3,5
				for wool, silk and clothes which require washing by hand)
				Partials wash cycles
				Rinse	-	1600	-	-		9
				Spin	-	1600	-	-	-	9
				Drain	-	0	-	-	-	9

Cycle duration

.display the on checked be can cycles wash the of duration The (*)

The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary according to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.

(*) Note: 10 minutes after the START, the machine will recalculate the time remaining until the end of the wash cycle on the basis of the load inside it; this value will then be shown on the display.

For all Test Institutes:

1)Test wash cycle in compliance with regulation EN 60456: set wash cycle with a temperature of 60°C.

2)Long wash cycle for cottons: set wash cycle with a temperature of 40°C.

3)Short wash cycle for cottons: set wash cycle with a temperature of 40°C.

Wash options

Steam Hygiene

This option enhances washing performance by generating steam during the wash cycle that eliminates any bacteria from fibres while treating them at the same time. Place the laundry in the drum, choose a compatible programme and select option “ “.

!The steam generated during washing machine operation may cause the porthole door to become hazy.

!It cannot be used in conjunction with , (90°C), , ,

,

,

,

,

,

,

,

.

Easy Iron

By selecting this option, the wash and spin cycles will be modified in order to reduce the formation of creases.

At the end of the cycle the washing machine drum will rotate slowly; the “Easy Iron” and START/PAUSE indicator lights will flash. To end the cycle press the START/PAUSE button or the “Easy Iron” button. For the Silk wash cycle, the machine will end the cycle while the laundry is soaking and the “Easy Iron” indicator light will flash.

To drain the water so that the laundry may be removed, press the START/PAUSE button or the “Easy Iron” button. ! It cannot be used in conjunction with , , , , , .

Time Saver

If you select this option, the wash cycle duration will be reduced by 30%-50%, depending on the selected cycle, thereby guaranteeing simultaneous water and energy saving. Use this cycle for lightly soiled garments.

! It cannot be used in conjunction with , , , , ,

, , , , .

Extra rinse

By selecting this option, the efficiency of the rinse is increased and optimal residual detergent removal is guaranteed. It is particularly useful for skin which is sensitive to detergents. We recommend this option is used with a full load of washing, or when a large amount of detergent is required.

! It cannot be used in conjunction with , , , .

7

Detergents and laundry

	EN	Detergent
		The type and quantity of detergent required depend on the type of
		fabric you are washing (cotton, wool, silk, etc.), as well as its colour,
		the washing temperature, the level of soiling and the hardness of
		the water in the area. Measuring out the detergent carefully will
		avoid wastage and help to protect the environment: although they
		are biodegradable, detergents still contain ingredients which alter
		the balance of nature.
		We recommend the following:
		• use powder detergents for white cotton garments and
		pre-washing.
		• use liquid detergents for delicate cotton garments and for
		all low-temperature wash cycles.
		• use gentle liquid detergents for wool and silk garments.
		The detergent should be poured into the relevant compartment
		- or the dispenser placed directly inside the drum - before the
		wash cycle begins. In the latter case, it will not be possible
		to select the Cottons with pre-wash cycle.
		! Do not use hand washing detergents because these create
		too much foam.

Preparing the laundry

•Shake out the garments before loading them into the machine.

•Divide the laundry according fabric type (symbol on the washing instruction label) and colour, making sure you separate the coloured garments from the white ones;

•Empty all pockets and check the buttons;

•Donotexceedthevalueslistedinthe“Table of wash cycles”, which refer to the weight of the laundry when dry.

How much does your laundry weigh?

1 sheet	400-500 g
1 pillowcase	150-200 g
1 tablecloth	400-500 g
1 bathrobe	900-1200 g
1 towel	150-250 g
1 pair of jeans	400-500 g
1 shirt	150-200 g

Washing recommendations

** Steam Refresh

This programme refreshes garments by removing bad odours and relaxing the fibres (1.5 kg, roughly 3 items). Insert dry items only (that are not dirty) and select programme “ “. The garments will be damp once the cycle is completed, so we recommend hanging them to dry. The “ “ programme makes ironing easier.

Moreover, with the “Steam Perfume” laundry balls, your favourite perfume can be added to your laundry. Place a few drops of perfume on the sponge contained inside the laundry ball, close it and insert it into the drum together with the laundry. Then launch the specific programme “ “. At the end of the cycle, garments will be relaxed and fragrant.

!Not recommended for wool or silk garments.

!Do not add too much perfume to the sponge in order to avoid it dripping.

!Do not add softeners or detergents.

Shirts: use the special “Shirts” wash cycle to wash shirts in different fabrics and colours to guarantee they receive the best possible care.

Jeans: use the special “Jeans” wash cycle for all denim garments; turn inside out before washing and use a liquid detergent.

Baby: use the special “Baby” wash cycle to remove the remove the soiling typically caused by babies, while removing all traces of detergent from nappies in order to prevent the delicate skin of babies from suffering allergic reactions. The cycle has been designed to reduce the amount of bacteria by using a greater quantity of water and optimising the effect of special disinfecting additives added to the detergent. At the end of the wash cycle, the machine will slowly rotate the drum; to end the cycle press the START/PAUSE button.

Silk: use the special “Silk” wash cycle to wash all silk garments. We recommend the use of special detergent which has been designed to wash delicate clothes.

Curtains: use the “Silk” wash cycle. These should be folded and placed inside the bag provided.

Wool: is the only washing machine brand to have been awarded the prestigious Woolmark Platinum Care endorsement (M.0508) by the Woolmark Company, which means that all woollen garments may be washed in the washing machine, even those which state “hand wash only” on the label. The “Wool” wash cycle can be used to wash all woollen garments in the washing machine while guaranteeing optimum performance.

Duvets: to wash double or single duvets (the weight of which should not exceed 3,5 kg), cushions or clothes padded with goose down such as puffa jackets, use the special “Duvets” wash cycle. We recommend that duvets are placed in the drum with their edges folded inwards (see figure) and that no more than ¾ of the total volume of the drum is used. To achieve the best results, we recommend that a liquid detergent is used and placed inside the detergent dispenser

drawer.

Quilts: to wash quilts with a synthetic outer layer, use the bag provided and set the wash cycle to “Duvets” . Bedlinen and towels: use the “Bed & Bath” cycle to wash laundry from all over the house; this optimises fabric softener performance and helps you save time and energy. We recommend the use of powder detergent.

Stubborn stains: it is wise to treat stubborn stains with solid soap before washing, and to use the Cottons with prewash cycle.

8

Precautions and tips

! The machine was designed and constructed in accordance with international safety regulations. The following information is provided for safety reasons and must therefore be read carefully.

General safety

•This appliance was designed for domestic use only.

•This appliance is not intended for use by persons

(including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a

person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

•Do not touch the machine when barefoot or with wet or damp hands or feet.

•Do not pull on the power supply cable when unplugging the appliance from the electricity socket. Hold the plug and pull.

•Do not touch the drained water as it may reach extremely high temperatures.

•Never force the porthole door. This could damage the safety lock mechanism designed to prevent accidental opening.

•If the appliance breaks down, do not under any circumstances access the internal mechanisms in an attempt to repair it yourself.

•Always keep children well away from the appliance while it is operating.

•If it must be moved, proceed with the help of two or three people and handle it with the utmost care. Never try to do this alone, because the appliance is very heavy.

•Before loading laundry into the washing machine, make sure the drum is empty.

Load balancing system

Before every spin cycle, to avoid excessive vibrations before every spin and to distribute the load in a uniform manner, the drum rotates continuously at a speed which is slightly greater than the washing rotation speed. If, after several attempts, the load is not balanced correctly, the machine spins at a reduced spin speed. If the load is excessively unbalanced, the washing machine performs the distribution process instead of spinning. To encourage improved load distribution and balance, we recommend small and large garments are mixed in the load.

Disposal

•Disposing of the packaging materials: observe local regulations so that the packaging may be re-used.

•The European Directive 2002/96/EC relating to Waste

Electrical and Electronic Equipment (WEEE) states that household appliances should not be disposed of using the normal solid urban waste cycle. Exhausted appliances should be collected separately in order to

optimise the cost of re-using and recycling the materials inside the machine, while preventing potential damage to the atmosphere and to public health.

The crossed-out dustbin is marked on all products

to remind the owner of their obligations regarding EN separated waste collection.

For more information relating to the correct disposal of household appliances, owners should contact their local authorities or appliance dealer.

Opening the porthole door manually

In the event that it is not possible to open the porthole door due to a powercut, and if you wish to remove the laundry, proceed as follows:

1. remove the plug from the electrical socket.

2. make sure the water level inside the machine is lower than the door opening; if

it is not, remove excess water using the drain hose, collecting it in a bucket as indicated in the figure.

3. remove the cover panel on the lower front part of the washing machine (see overleaf).

4. pull outwards using the tab as indicated in the figure, until the plastic tie-rod is freed from its stop position; pull downwards until you hear a “click”, which indicates that the door is now unlocked.

5. open the door; if this is still not possible repeat the procedure.

6. reposition the panel, making sure the hooks are securely in place before you push it onto the appliance.

9

Care and maintenance

Cutting off the water and electricity EN supplies

•Turn off the water tap after every wash cycle. This will limit wear on the hydraulic system in the machine and help to prevent leaks.

•Unplug the appliance when cleaning it and during all maintenance work.

Cleaning the machine

The outer parts and rubber components of the appliance can be cleaned using a soft cloth soaked in lukewarm soapy water. Do not use solvents or abrasives.

Cleaning the detergent dispenser drawer

To remove the drawer, press lever (1) and pull the drawer outwards (2) (see figure).

Wash it under running water; this procedure should be repeated frequently.

To access the pre-chamber:

1. take off the cover panel on the front of the machine by first pressing it in the centre and then pushing downwards on both sides until you can remove it (see figures);

2. position a container so that it will collect the water which flows out (approximately 1.5 l) (see figure);

3. unscrew the lid by rotating it in an anti-clockwise direction (see figure);

4.clean the inside thoroughly;

5.screw the lid back on;

6.reposition the panel, making sure the hooks are securely in place before you push it onto the appliance.

Caring for your appliance drum

•Always leave the door ajar to prevent unpleasant odours from forming.

Cleaning the pump

The washing machine is fitted with a self-cleaning pump which does not require any maintenance. Sometimes, small items (such as coins or buttons) may fall into the protective pre-chamber at the base of the pump.

! Make sure the wash cycle has finished and unplug the appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If there are any cracks, it should be replaced immediately: during the wash cycles, water pressure is very strong and a cracked hose could easily split open.

10

Trouble shooting

	Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Centre
			EN
	(see “Assistance”), make sure that the problem cannot be not solved easily using the following list.
	Problem:	Possible causes / Solutions:

The washing machine does not switch on.

•The appliance is not plugged into the socket fully, or not enough to make contact.

•There is no power in the house.

The wash cycle does not start.

•The door is not closed properly.

•The START/PAUSE button has not been pressed.

•The water tap has not been opened.

•A delayed start has been set.

The washing machine does not fill with water.

The washing machine door remains locked.

•The water inlet hose is not connected to the tap.

•The hose is bent.

•The water tap has not been opened.

•There is no water supply in the house.

•The pressure is too low.

•The START/PAUSE button has not been pressed.

•If you have selected the “Baby ” cycle or the “Easy iron ” option, when the wash cycle has finished the machine will slowly rotate the drum; to end the cycle press the START/PAUSE button or the “Easy iron ” button. If you

have selected the “Silk ” wash cycle, the machine will end the cycle while the laundry is soaking; to drain the water so that the laundry may be removed, press the START/PAUSE button or the “Easy iron ” button.

The machine continuously fills with water and drains.

The washing machine does not drain or spin.

The machine vibrates a lot during the spin cycle.

The washing machine leaks.

•The drain hose is not fitted at a height between 65 and 100 cm from the floor

(see “Installation”).

•The free end of the hose is under water (see “Installation”).

•If the dwelling is on one of the upper floors of a building, there may be problems relating to water drainage, causing the washing machine to fill with water and drain continuously. Special anti-draining valves are available in shops and help to prevent this inconvenience.

•The wall drainage system is not fitted with a breather pipe.

•The wash cycle does not include draining: Some wash cycles require the drain phase to be started manually (see “Wash cycles and options”).

•The “Easy iron” option is enabled: to complete the wash cycle, press the

START/PAUSE button (“Wash cycles and options”).

•The drain hose is bent (see Installation).

•The drainage duct is clogged.

•The drum was not unlocked correctly during installation (see “Installation”).

•The machine is not level (see “Installation” ).

•The machine is trapped between cabinets and walls (see “Installation”).

•The load is unbalanced (see “Detergents and laundry”).

•The water inlet hose is not screwed on properly (see “Installation”).

•The detergent dispenser is blocked (to clean it, see “Care and maintenance”).

•The drain hose is not fixed in place properly (see “Installation”).

The icons corresponding to the “Phase in progress” flash rapidly at the same time as the ON/OFF indicator light.

•Switch off the machine and unplug it, wait for approximately 1 minute and then switch it back on again. If the problem persists, contact the Technical Assistance Service.

There is too much foam.

The washing machine door remains locked.

•The detergent is not suitable for machine washing (it should display the text

“for washing machines” or “hand and machine wash”, or the like).

•Too much detergent was used.

•Perform the manual unlocking procedure (see “Precautions and tips”).

! Note: To exit “Demo mode”, press and hold the two “ON/OFF” and “START/PAUSE” buttons simultaneously for 3 seconds.

11