Hotpoint AQCF 852 BU, AQCF 852 BI User Manual

Instruction booklet

GB

English,1

AQUALTIS

AQCF 852 BI

AQCF 852 BU

This symbol reminds you to read this instruction manual.

Keep this instruction booklet on hand in order to refer to it

when necessary. Take it with you when you move, and, should you sell this appliance or pass it on to another party, make sure that this booklet is supplied along with the dryer so that the new owner may be informed about warnings and suggestions on how the dryer works.

Read these instructions carefully; the following pages contain important information on installation and suggestions on how the appliance works.

TUMBLE DRYER

Contents

GB

Important Information, 2-3

Installation, 4

Where to put your dryer Ventilation

Electrical connection

Before you start using your dryer

Dryer Description, 5

Open the door

The Features

Control Panel

The Display, 6

Start and Programmes, 7-12

Choosing a Programme

Special Programmes

Table of Programmes

The Controls

Laundry, 13-14

Sorting your laundry

Wash care labels

Special clothing items

Drying times

Warnings and Suggestions, 15

General safety

Disposal

Save energy and respect the

Environment

Maintenance and Care, 16

Switching off the electricity

Clean the filter after each cycle

Check the drum after each cycle

Empty the Water Container after each cycle

Cleaning the Condenser

Cleaning the dryer

Troubleshooting, 17

Service, 18

Spare parts

1

Important Information

For your Condenser dryer to operate efficiently, you must follow the regular maintenance

GB schedule shown below:

Fluff Filter – You MUST Clean the fluff filter after every drying cycle.

Step 1

Open the door of your dryer.

Failure to clean the filter after every drying cycle will affect the drying performance of your machine – It will take longer to dry and as a result will use more electricity during drying.

Water Container – You must empty the water container after every drying cycle.

2

Step 1

Pull the water container towards you and remove it fully from the dryer.

Step 2

Pull out the filter (using the two finger grips).

Step 3

Open the filter by releasing the clip.

Step 4

Clean any fluff deposits from the inside surface of the filter mesh.

Step 5

Refit the filter – Never run the dryer without a filter.

Step 2

Empty the Water from the

Container.

Step 3

Refit the Water Container ensuring that it is pushed fully back into position...

Failure to empty the Water Container will result in:

-The machine will stop heating (so the load may be wet at the end of the cycle).

-The ”Empty Water” light will flash to tell you

that the Container is full.

The water bottle/clean filter light comes on when you select a programme to remind you to make sure that the water bottle is empty and that the filter is clean before starting a new cycle’

Priming the Water Collection System

When your dryer is new, the Water Container will not collect Water until the system is primed, this will take 1 or 2 drying cycles. Once primed it will collect Water during every cycle.

2

Condenser unit - You must clean the fluff from

the condenser every month!

GB

Step 1

Open the Condenser Cover - hold the handle and pull towards you.

Step 2

Remove the condenser by rotating the 3 clips then pulling the condenser towards you. (There may be some water in the tubes this is normal).

Step 3

Flush the condenser, from the rear with water, to remove any fluff deposits.

Step 4

Refit the condenser unit - ensure that the unit is pushed in fully, all 3 clips are resecured and the positioning arrows on the front of the condenser are pointing upwards.

Failure to clean the condenser could cause premature failure of your dryer!

3

Installation

Where to put your dryer

	GB • Place your dryer at a distance
	from gas ranges, stoves,	10 mm
	heaters, or cooktops because
	flames can damage the
	appliance.
	If you are going to install the
	appliance under a work counter,	15 mm	15 mm
	be sure to leave a 10 mm
	space between the top and any
	other objects on or above the
	machine and a 15 mm space

between the sides and lateral

furnishings or walls. This is to ensure proper air circulation.

Ventilation

• When the dryer is in use, there has to be adequate ventilation. Make sure you put your dryer in an environment that is not damp and has proper air circulation throughout. Airflow around the dryer is essential to condense the water produced during the washing, the dryer will not operate efficiently in an enclosed space or cupboard.

If using the dryer in a small or cold room some condensation will be experienced.

We do not recommend that the dryer is installed in a cupboard but the dryer must never be installed behind a lockable door, a sliding door or a door with a hinge on the opposite side to that of the dryer door.

Water Drain

If the machine is positioned close to a drain it is possible to drain the condensed water directly without using the waterbottle. In which case it is no longer necessary to empty the water bottle at the end of each cycle.If the Dryer is positioned above or close to a Washing Machine the same drainage can be used. Just unlink the tube indicated in figure A and connect it to the drainage.

If the drainage is further away than the length of the tube it is possible to buy and connect a tube of the same diameter and the necessary length in order to reach the drainage. To install the new tube just substitute the existing one as indicated in figure B inserting it in the same place.

The drain tube has to be below 1 m from the bottom of the Dryer.

Once the Dryer has been installed please assure that the drain tube is not bent or contorted.

2

2

H<1m

Fig. A	Fig. B

Electrical connection

Make sure of the following before you insert the plug into the electrical socket:

•Ensure your Hands are dry.

•The socket must be grounded.

•The socket must be able to sustain the machine’s maximum power, which is indicated on the rating label (see Dryer Description).

•Power voltage must be within the values indicated on the rating label (see Dryer Description).

•The socket must be compatible with the dryer’s plug.

Should this not be the case, replace the plug or the socket.Do not use extension cords.

The dryer must not be installed outdoors, even if the space is

sheltered. It can be very dangerous if exposed to rain or storms.

Once installed, the dryer’s electrical wire and plug must be within reach.

The power cord must not be bent or squashed.

The power cord is supplied fitted with a BS1363 plug and with a 13 amp BS1362 fuse. If it is necessary to fit a replacement fuse, it must be a 13 Amp ASTA approved to BS1362 type. WARNING: The plug must not be used without a fuse cover.

If a replacement fuse holder/cover is required, it must be of the same colour coding or wording as shown on the base of the plug. Replacements are available from authorised dealers.

Moulded plug

Changing the plug

The wires in the power cord are coloured in accordance with the following.

Green and Yellow (Earth)			13A ASTA approved fuse
wire to terminal marked			to BS 1362.
“E”, symbol x, or coloured	GREEN &
green and yellow.	YELLOW
	BROWN	13 ampere fuse
			Brown (live) wire to teminal
Blue (Neutral) wire to	BLUE	CROSS-BAR	marked “L” or coloured
terminal marked ”N” or		CORD GRIP	red.
coloured black.

If the plug being replaced is a non-rewirable type, then the cut-off plug must be disposed of safely. DO NOT leave it where it can be inserted into a socket and create a shock hazard.

The power cord should be checked periodically and replaced by a cord specially prepared for this dryer and fitted only by authorized technicians (see Service). New or longer power cords are supplied at an extra charge by authorized dealers.

The manufacturer denies any responsibility should any of these rules not be followed.

If in doubt about any of the above consult a qualified electrician.

Before you start using your dryer

Once you’ve installed your dryer and before you use it, clean the inside of the drum to remove any dust that could have accumulated during transportation.

4

Dryer Description

To open door	The Features
	Rating	GB
Pull on handle	Plate
	Water
	container	Model &
		Serial
	Filter	Numbers

	Condenser unit	Air Intake
		Grille
	(cover open)

					Condenser
	Control Panel				cover handle
					(Pull to open)
			ECO Light	Start/Pause Button &	Child Lock
	On/Off Button & Light	Indicator	Display Panel	Light
					Button & Light

								Clean	Empty Water	Programme
Programme Knob	Option Buttons and Lights
								Condenser	Clean Filter	Progress Light
								Light	Light

The On/Off button/ light , if the dryer is running and this button is pressed the dryer is turned off. The light signals that your dryer is in use or ready to select a programme.

The Programmes knob sets the programme: rotate until the indicator is pointing to the programme you want to select (see Start and Programmes).

The Option buttons/ lights select available options for your selected programme. The lights indicate that the option has been selected (see Start and Programmes).

The Display Panel has three sections: Sensor Dry = Drying level, Timed dry = Drying time and Time to End / Delay start each with a corresponding selection button (see The Display).

START/PAUSE button with indicator light : when the green indicator light flashes slowly, press the button to start the programme. When the cycle has started, the indicator light is illuminated in a fixed manner. To pause the programme, press the button again; the indicator light will turn orange and begin to flash again.

To restart the programme from the point at which it was interrupted, press the button again (see Start and Programmes).

The Programme Progress Lights indicate each state of the programme by turning on as appropriate.(see Start and Programmes).

The Empty Water indicator “H2O” signals that the water container should be emptied. The light will take a few seconds to go out after replacing the empty water container; the dryer must be running for this to happen (see The Controls).

Note: if the water bottle is full the display shows “H2O” and the indicator flashes, the heat is turned off and your clothes will not dry.

The Empty Water Clean Filter Light gives a reminder before every programme, that its essential to clean the filter and empty the water container every time the dryer is used (see Maintenance and Care).

The Clean Condenser Light gives a reminder, that its essential to clean the condenser at regular intervals (see Maintenance and Care).

The Child Lock button/light Press and hold this button after selecting your programme and any options. This prevents the programme settings from being changed. When the light is lit the other buttons and programme knob are disabled. Hold the button to cancel and the light will go out.

ECO Light - this light is illuminated as you select options that use less energy (see the controls).

5

The Display

The Display has three sections each with its corresponding button.

GB

Sensor Dry

After selecting a programme that has a Sensor Dry Option, press and release the button until the required dryness sensing level is displayed. If the sensing option is not available the display will flash and the buzzer beeps three times.

Some drying programmes are not compatible with all 5 sensor drying levels.

Dryness levels available

Damp: Retains maximum moisture in the garments, which is ideal for difficult to iron fabrics such as linen.

Iron: Retains moisture in your clothes to help make ironing easier.

Hanger: Dries you clothes ready to be hanged for final drying; Use for items that can simply be hung up to finish drying.

Cupboard: Dries your items to put away.

Ready to wear: Dries clothes so that they are immediately ready to wear.

Timed Dry

After selecting a Programme that has a Timed Dry Option, press the Timed Button to insert a drying time. The display will reduce the selected time each time you press and release this button (see Start and Programmes). Each press decreases the set time 180, 160, 120, 90, 60, 30, 20 and then repeats. If the Timed Dry option is not available the display will flash and the buzzer beeps three times.The selected time remains displayed after the programme starts and cannot be changed after the Start/ Pause Button , is pressed.

You can either choose a sensor dry level or a drying time.

Delay Start

After selecting a Programme that has a Delay Start Option a delay start time can be selected.

Each press of the Delay start button advances the delay setting in 1 hour increments from “1h” to

“24h” then “OFF” and then after five seconds cancels the delay.

For delays of 10 hours or more the display counts down the time in hours until 10 hours, then the display shows “9:59” and then counts down in minutes. For delays of 9 hours or less the display shows hours and minutes and then counts down in minutes for all of the delay.

After the Start/Pause Button is pressed the time cannot be changed.

When the delay period finished the symbol is off and the Time to End is displayed.

If you have chosen a timed drying the display during programming will show the drying time only in the timed drying display in the middle. After having pressed start the machine will turn the time display on and visualize the countdown of the programme time.

Time to End

If the delay icon is off the time displayed is the Time to End of the programme running.

When timed programmes are selected the time displayed throughout the cycle is the actual time remaining. When an Automatic programme is selected the time displayed is an estimate of the time remaining. When the programme is selected the display shows the time required to dry a full load, after around 10 minutes the controller calculates a better estimate of the cycle time.

The time to end is displayed in hours and minutes and counts down each minute.

The colon between the hours and minutes display flashes to show that the time is counting down. The Display also shows if there is a problem with your dryer, if this occurs the display will show F followed by a fault code number, the four option lights and the pause light will also flash Orange

(see Troubleshooting).

6