General 15-660 User Manual

Sealed double bearing design. Adjustable aluminum tool rests. Heavy-duty wheel guards with dust chute. Equipped with eye-shield protectors. 4 rubber base mounts to reduce vibration. 2 Flexible work lights for clear view of
grinding wheels and workpiece. Variable speed for grinding or sharpening. Powerful 2.5 amp. induction motor for lon-
glasting, smooth performance. Convenient water tray to cool sharpened
items. Wheel dresser included.
WHEEL SIZE 6” x
3
4
” (52 x 19 mm)
ARBOR SPEED 2000 - 3450 RPM (VARIABLE)
ARBOR SIZE
1
2
” (1 mm)
MO
TOR
110 V, 2.5 A WEIGHT
28.5 LBS (13 kg)
REVISION 2 OCT 17/06 © Copyright General International 04/2007
THANK YOU
for choosing this General International model 15-660 Bench Grinder. This bench grinder has been carefully tested and inspected before shipment and if properly used and maintained, will provide you with years of reliable service. To ensure opti­mum performance and trouble-free operation, and to get the most from your investment, please take the time to read this manual before assembling, installing and operating the unit.
The manual’s purpose is to familiarize you with the safe operation, basic function, and features of this bench grinder as well as the set-up, maintenance and identification of its parts and components. This manual is not intended as a substitute for formal woodworking instruction, nor to offer the user instruction in the craft of woodworking. If you are not sure about the safe­ty of performing a certain operation or procedure, do not proceed until you can confirm, from knowledgeable and qualified sources, that it is safe to do so.
Once you’ve read through these instructions, keep this manual handy for future reference.
All component parts of General® International machinery are carefully tested and inspected during all stages of production, and each machine is thoroughly inspected upon completion of assembly. Because of our commit­ment to quality and customer satisfaction, General® International agrees to repair or replace, within a period of 24 months from date of purchase, any genuine part or parts which, upon examination, prove to be defective in work­manship or material. In order to obtain this warranty, all defective parts must be returned freight pre-paid to General® International Mfg. Co., Ltd. Repairs attempted without our written authorization will void this warranty.
GENERAL ® INTERNATIONAL WARRANTY
Disclaimer:
The information and specifications in this manual pertain to the unit as it was supplied from the factory at the time of printing. Because we are committed to making constant improvements, General International reserves the right to make changes to components, parts or features of this unit as deemed necessary, without prior notice and without obligation to install any such changes on previously delivered units. Reasonable care is taken at the factory to ensure that the specifi­cations and information in this manual corresponds with that of the unit with which it was supplied. However, special orders and “after factory”
modifications may render some or all information in this manual inapplicable to your machine. Further, as several generations of this bench grinder and several versions of this manual may be in circulation, if you own an earlier or later version of this unit, this manual may not depict your machine exactly. If you have any doubts or questions contact your retailer or our support line with the model and serial number of your unit for clarification.
GENERAL® INTERNATIONAL
8360 Champ-d’Eau, Montreal (Quebec) Canada H1P 1Y3
Telephone (514) 326-1161 • Fax (514) 326-5555 • www.general.ca
1. Make sure that the operator has been proper­ly trained and has read, and understands, the owners’ manual before operating any machinery.
2. Do not operate this bench grinder when tired, dis­tracted or under the effects of drugs, alcohol or any medication that impairs reflexes or alertness.
3. Keep the work area well lit,clean and free of debris or clutter.
4. Keep children and visitors at a safe distance; do not permit them to operate the unit.
5. Childproof and tamper proof your shop and all machinery with locks, master electrical switches and switch keys, to prevent unauthorized or unsu­pervised use.
6. Stay alert! Give your work your undivided attention. Even a momentary distraction can lead to serious injury.
7. Do not wear loose clothing, gloves, bracelets, neck­laces or other jewelry while operating machinery. Wear protective hair covering to contain long hair and wear non-slip footwear.
8. Fine particulate dust is a carcinogen that can be hazardous to health. Work in a well ventilated area and wear eye, ear and respiratory protection devices.
9. Whenever possible use a dust collector to minimize health hazards.
10. Keep hands and other body parts well away from grinding wheels and all moving parts or other cutting tools. Do not clear chips and grinding dust away with hands, use a brush.
11. Make sure the grinding wheels are running at full operating speed before grinding.
12. Do not force the grinding wheels or push too hard. The unit will perform better, safer and more effec­tively at the speed or rate for which it was designed.
13. Never leave the power on or the machine running while it is unattended.
14. Use recommended speed grinding wheels, acces­sories, and work piece material.
15. Never stand or lean on the bench grinder. Serious injury could occur if the unit is tipped or if uninten­tional contact is made with its’ moving parts.
16. Before starting the unit, make sure the grinding wheels are securely installed and tight to the arbor shaft.
17. Keep all guards and safety devices in place and in good working order. If a guard must be removed for maintenance or cleaning make sure it is pro­perly re-installed before using the machine again.
18. Before performing any maintenance,repairs or ad­justments including wheel changes, make sure the power is off and the unit is unplugged.
19. Before plugging in and turning on the power, make sure that any adjustment tools, keys or wrenches have been removed and safely stored.
20. Always, make sure that switch is in "OFF" position before plugging in the power cord.
21. Only use accessories that are made or designed for this machine.The use of parts or accessories that are not recommended by General International will void any warranty claims and may result in injury.
22. Make sure the machine is properly grounded. This unit is supplied with a three-prong electric plug; it should be plugged into a three-pole electrical receptacle. Never remove the third prong.
23. Do not use this bench grinder for any purpose other than it’s intended use. If used for other purposes, General International disclaims any real or implied warranty and holds itself harmless for any injury which may result from such use.
RRuulleess ffoorr SSaaffee OOppeerraattiioonn
To help ensure safe operation, please take a moment to learn the machine’s applications and limita­tions, as well as potential hazards. General International disclaims any real or implied warranty and hold itself harmless for any injury that may result from the improper use of it’s equipment.
AAddddiittiioonnaall SSaaffeettyy IInnssttrruuccttiioonnss
ffoorr BBeenncchh GGrriinnddeerrss
Because each shop situation is unique, no list of safety guidelines can ever be complete.
The most important safety feature in any shop is the knowledge and good judgement of the user.
Use common sense and always keep safety considerations, as they apply to your individual shop situation first
and foremost in mind. If you have any doubts about the safety of an operation you are about to
perform: STOP! Do not perform the operation until you have validated from qualified individuals
if the operation is safe to perform and what is the safest method to perform it.
1. LIMIT EXPOSURE TO DUST
Some dust created by power sanding, sawing, grinding, drilling and similar operations contains chemicals known to the state of California to cause cancer, birth defects or other reproductive harm. Some examples include:
• Lead from lead-based paint.
• Crystalline silica from bricks, cement and other masonry products.
• Arsenic and chromium from chemically treated lumber.
Your risk from these exposures varies depending on how often you do this types of work. To reduce your exposure to these chemicals, work in a well ventila­ted area and work with approved safety equipment such as dust masks that are specially designed to filter out microscopic particles.
2. ALWAYS USE EYESHIELDS, WHEEL GUARDS AND
SPARK GUARDS
The supplied eye shields, wheel guards and spark guards should be maintained, properly installed on the unit and used at all times.
3. REPLACE DAMAGED PARTS OR COMPONENTS
IMMEDIATELY
Damaged parts or components may lead to a haz­ardous situation that could cause serious injury. Replace any damaged parts or components before operating the unit.
4.
INSPECT GRINDING WHEELS BEFORE EACH USE
Handle grinding wheels carefully. A damaged or chipped grinding wheel can discharge debris towards the operator at high speeds. Before installing or replacing a grinding wheel as well as before each use, take a moment to inspect the grinding wheel(s) for cracks, chips or other visible signs of damage. Do not use a damaged wheel. Tighten the spindle nut enough to hold the grinding wheel firmly but do not over tighten as excessive clamping force can damage the wheel. Use only the wheel flanges provided with the grinder and do not remove the blotter or label on either side of the grinding wheel. When replacing a grinding wheel select only wheels that are rated to a higher maxi­mum R.P.M. than the maximum of the Bench Grinder.
5. ADJUST TOOL RESTS AND SP
ARK GUARDS AS
NEEDED
The diameter of the grinding wheels will decrease with use. Adjust the tools rests and sparks guards accordingly to maintain a distance of 1/16”from the wheel.
6. DO NOT STAND IN FRONT OF THE BENCH GRINDER DURING START-UP
To avoid potential injury caused by debris ejected from a damaged wheel, stand to one side of the Bench Grinder when starting the unit. While standing to the side, turn the unit on, wait one minute until the unit comes up to full speed before grinding.
7. DO NOT OPERATE IN THE VICINITY OF FLAMMA­BLE MATERIALS
Bench grinders will produce sparks and debris dur­ing grinding. Be sure to keep flammable materials from the immediate vicinity. Be sure to clean the grinding dust from the back of the Bench Grinder frequently.
8. DO NOT FORCE THE WORKPIECE AGAINST THE GRINDING WHEEL
Excessive force especially to a cold grinding wheel may damage the wheel and create a dangerous situation. Apply the workpiece against the wheel slowly and use firm, steady even pressure. Do not grind against the sides of the grinding wheel and do not apply coolant direct to the grinding wheel.
9. KEEP ALL WHEEL GUARDS IN PLACE
Do not use the bench grinder with the wheel guards removed.
10. KEEP THE TOOL RESTS FIRMLY TIGHTENED
Inspect and re-tighten tools rests before each use.
11. USE THE SUPPLIED WHEEL DRESSER
Always use the supplied wheel dresser to resurface the face of the grinding wheel.
GROUNDING INSTRUCTIONS
IN THE EVENT OF A MALFUNCTION OR BREAKDOWN,
grounding provides a path of least resistance for elec­tric current and reduces the risk of electric shock. This tool is equipped with an electric cord that has an equipment-grounding conductor and a grounding plug. The plug MUST be plugged into a matching receptacle that is properly installed and grounded in accordance with ALL local codes and ordinances.
DO NOT MODIFY THE PLUG PROVIDED.
If it will not fit the receptacle, have the proper recepta­cle installed by a qualified electrician.
IMPROPER CONNECTION of the equipment-grounding conductor can result in risk of electric shock. The con­ductor with green insulation (with or without yellow stripes) is the equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, DO NOT connect the equipment-grounding conductor to a live terminal.
CHECK with a qualified electrician or service person if you do not completely understand the grounding instructions, or if you are not sure the tool is properly grounded.
USE ONLY 3-WIRE EXTENSION CORDS THAT HAVE 3-PRONG GROUNDING PLUGS AND 3-POLE RECEPTACLES THAT ACCEPT THE TOOL’S PLUG. REPAIR OR REPLACE DAMAGED OR WORN CORD IMMEDIATELY.
GUIDELINES FOR EXTENSION CORDS
USE PROPER EXTENSION CORD.
Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage, resulting in loss of power and cause over­heating. The table below shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt,use the next heavier gauge. The smaller the gauge number, the heavier the cord.
BE SURE YOUR EXTENSION CORD IS PROPERLY WIRED
and in good condition. Always replace a damaged extension cord or have it repaired by a qualified per­son before using it. Protect your extension cords from sharp objects, excessive heat and damp or wet areas.
Use a separate electrical circuit for your tools. This cir­cuit must not be less than # 12 wire and should be pro­tected with a 15 Amp time delay fuse. Before connect­ing the motor to the power line, make sure the switch is in the OFF position and the electric current is rated the same as the current stamped on the motor nameplate. Running at a lower voltage will damage the motor.
This tool is intended for use on a circuit that has a receptacle like the one illustrated in Figure . Figure shows a 3-prong electrical plug and receptacle that has a grounding conductor. If a properly grounded receptacle is not available, an adapter (Figure ) can be used to temporarily con­nect this plug to a 2-contact grounded receptacle. The temporary adapter should be used only until a proper­ly grounded receptacle can be installed by a qualified technician. The adapter (Figure ) has a rigid lug extending from it that MUST be connected to a perma­nent earth ground, such as a properly grounded receptacle box. The Canadian Electrical Code pro­hibits the use of the adapters.
EELLEECCTTRRIICCAALL RREEQQUUIIRREEMMEENNTTSS
In all cases, make certain the receptacle is pro­perly grounded. If you are not sure, have a quali­fied electrician check the receptacle.
This tool is for indoor use only. Do not expose to rain or use in damp locations.
This tool must be grounded while in use to protect the operator from electrical shock.
MINIMUM GAUGE FOR EXTENSION CORDS (AWG)
(When using 120 volts only)
AMPERE RATING TOTAL LENGTH OF CORD IN FEET
More than not more than 25’ 50’ 100’ 150’
0 6 18 16 16 14 610 18161412 10 12 16 16 14 12 12 16 14 12
not recommended
5
WHEEL GUARD – Covers the grinding wheels and pro-
tects against accidental contact.
WHEEL COVER – Covers the grinding wheels and pro­vides access for routine maintenance.
MOTOR HOUSING – Contains the electric motor.
EYE SHIELD – Protective see- thru Lexan shields to pre-
vent any loose debris from coming into contact with the operator.
FLEXIBLE WORK LIGHT – Illuminates the tool rest/work­piece area in front of the grinding wheel
SPARK GUARDS – Prevents hot sparks and debris from coming into contact with the operator.
TOOL REST ADJUSTABLE SUPPORTS – Allows the operator to position the tool rest closer to the wheel as needed as the wheel decreases in diameter due to wear.
TOOL RESTS – Used to support the workpiece that is being ground. Adjustable for grinding angled surfaces.
GRINDING WHEEL 100 GRIT – Used to remove light material from workpiece.
GRINDING WHEEL 36 GRIT – Used to remove rough material from workpiece.
ON/OFF SWITCH – Used to turn “ON” and turn “OFF” the grinder and the worklights.
WHEEL DRESSER & HOLDER – Used to clean, smooth and resurface the Grinding Wheels.
QUENCH TRAY – Used to cool the workpiece after grinding.
VARIABLE SPEED CONTROL – Controls grinding wheel speed.
6
6” VARIABLE SPEED BENCH GRINDER
15-660
IDENTIFICATION OF PARTS & COMPONENTS
Grinding
Wheel
(36 grit - Grey)
Spark Guard
Wheel
Cover
Motor
Housing
Wheel
Dresser &
Holder
Wheel Guard
Flexible Work Light
Eye Shield
Grinding Wheel
(100 grit - White)
Tool Rest
Speed Control
On/Off Switch
Quench Tray
Tool Rest Adjustable Supports
ASSEMBLY INSTRUCTIONS
TOOLS NEEDED
A 10 mm and 12 mm open-end wrench (not included) will be required to install the Tool Rest Assemblies and the spark guards. A Phillips or flat-head screwdriver to remove the wheel covers. A large flat head screwdirver for removing or changing grinding wheels.
NOTE: All images show right hand side installation. Repeat these procedures to install left hand side components.
For your own safety, never connect the plug to power source outlet until all assembly and adjustment steps are completed, and you have read and understood the safety and operating instructions.
INSTALLING THE TOOL RESTS
The Bench Grinder is supplied with two different Tool Rest assemblies. The Left Side Tool Rest is entirely flat.The Right Side Tool Rest is also flat, but has a “V” groove for sharpening drill bits.
1. Attach the tool rest (1) to the support (7) using the flat washer (2) and adjustment knob (3).
2. Thread two bolts (4) through two big washers (5) and the tool rest support (1) and into the wheel housing (6).
3. Adjust the tool rests until they are 1/16” from the grinding wheel. Firmly tighten the hex head bolts holding the support.
INSTALLING THE SPARK GUARDS
1. Install the spark guard (1) to the inside surface of the wheel cover (2) using a flat washer (3) and hex head bolt (4).
2. Adjust the spark guards until they are 1/16” from the grinding wheels. Firmly tighten the hex head bolt.
INSTALLING THE EYE SHIELDS
1. Attach the eye shield to the spark guard (1) by inserting the carriage bolt (2) through eye shield (3), work light(4) and spark guard (1) as shown.
2. Secure the assembly to the spark guard using a flat washer (5) and lock knob (6) and tighten until the eye shield remains in the desired position.
INSTALLING THE WHEEL DRESSER
1. Peel off the adhesive backing from the wheel dresser holder (1).
2. Stick the holder on the top of the bench grinder (2).
3. Insert the wheel dress (3) on the holder.
7
4
5
1
3
2
6
7
3
2
1
8
QUENCH TRAY
The quench tray is provided to cool the workpiece during and after grinding.
1. Slide the quench tray onto the base of the bench grinder as shown.
2. Partially fill the quench tray with water. Do not over fill. Do not use any liquid in the quench tray other than water.
3. Dip the workpiece into the water after grinding to cool it.
4. Do not apply water directly onto the grinding wheels.
SECURING THE GRINDER TO A WORK SURFACE
Note: To avoid tipping over or sliding during operations, the grinder should be secured to the work surface.
1. The base of the grinder has 2 mounting holes allo-
wing the user to permanently mount the grinder to a workbench or stand.
2. Place the grinder on the work surface, mark the holes on the work surface and drill 3/8” holes. Use appro­priate length bolts, washers and nuts to secure to secure the grinder to the bench.
3. If the workbench moves or shakes during operation, the workbench must be fastened to the floor.
4. The grinder is designed for use on horizontal surfaces only. Motor damage may result when mounted on a non-horizontal surface.
1. Bench grinder
2. Hex head bolt
3. Rubber washer
4. Flat washer
5. Workbench or stand
6. Flat washer
7. Lock washer
8. Hex nut
9. Jamb nut
Remove the switch key whenever the grinder is not in use. Place it in a safe place and out of the reach of children.
OPERATIONS
POWER ON
POWER OFF SAFETY KEY
(PREVENTS START-UP WHEN REMOVED)
ADJUSTMENTS AND CONTROLS
POWER “ON/OFF” SWITCH
Make sure the switch is in the “OFF” position before plugging in the power cord.
VARIABLE SPEED CONTROL
The grinder is equipped with a variable speed control. When the speed control knob is turned completely counter-clockwise (low) the RPM is at 2000. Wheel speed increases as the knob is turned clockwise. When the speed control knob is turned completely clockwise (high) the RPM is 3450.
FLEXIBLE WORK LIGHT
The work light functions of the same switch as the grinder.To turn the grinder switch on and off.
To reduce the risk of fire, use a 110V 10 Watt (or less) medium base, track light bulb. Do not use a bulb that extends past the end of the light housing.
GRINDER OPERATION
The bench grinder is designed for hand held grinding, sharpening, and cleaning operations.
ALWAYS WEAR EYE PROTECTION!
Hot sparks are produced during grinding operations.
1. The power switch must be in the “OFF” position.
2. Make sure the spark guards and tool rests are set 1/16” from the grinding wheels. Before starting the machine,
turn the grinding wheel by hand one full turn to make certain the wheels to do not come into contact with the spark guards or tools rests.
3. Stand to the side of the bench grinder and plug in the power cord to the correct power source.
4. Remain to the side of the bench grinder and turn it “ON”.
5. Allow the grinding wheels to come up to a steady speed for at least one minute.
6. Adjust the eye shields as needed and place the workpiece on the appropriate tool rest for the desired operation.
7. Slowly move the workpiece towards the grinding wheel until it lightly touches. Move the workpiece back and
forth across the front surface of the grinding wheel removing the amount of material desired. NEVER GRIND ON THE SIDES OF THE GRINDING WHEELS.
8. For drill bits, lay the drill bit flat in the “V” groove. Firmly hold on to the dril bit shank. Slide the drill bit toward the grinding wheel until it lightly touches. Keep the drill bit flat to the plate and rotate the drill bit.
9. Dip the hot end of the workpiece into the water in the quench tray to cool it as needed.
10. When finished grinding turn “OFF” the machine by pushing down on the Power Switch. CAUTION: It will take a few
minutes for the grinding wheels to come a complete stop.
11. Avoid contact with the housing until it is cool. Unplug the Bench Grinder and to prevent unauthorized use, remove the switch key and store it in a safe place.
9
VARIABLE SPEED
CONTROLLER
USING THE WHEEL DRESSER
The Wheel Dresser is used on the grinding wheels to remove imperfections or built-up material as well as to square up or re-surface the grinding edge of the wheels.
1. Turn “ON” the Bench Grinder. Let the grinding wheel come up to a steady speed for one minute.
2. Place the Wheel Dresser (1) flat on the Tool Rest with the flat face of the dressing stone facing the grinding wheel.
3. Firmly hold the handle of the Wheel Dresser and slow­ly move the Wheel Dresser forward making light con tact with the grinding wheel (2). Move the Wheel Dresser from side to side across the Tool Rest until the edge of the wheel is square and the surface is clean.
4. When finished turn “OFF” the machine and let the grinding wheel come to a complete stop.
5. Inspect the grinding wheel for any damage.
6. The grinding wheel may now be slightly smaller in diameter after dressing. Readjust the tool rests and spark
guards as needed to maintain a 1/16” clearance to the grinding wheel.
CHANGING GRINDING WHEELS
NOTE: Do not remove the cardboard discs (blotters) from the sides of a new wheel because they work with the flanges to hold and secure the wheel on the arbor.
Inspect the new wheel for cracks or other visible signs of damage. Discard the wheel if any such damage is found.
Two end plates will need to be removed for wheel changes.
1. Loosen the lock knobs and remove the tool rests.
2. Remove the screws and take off the end-plate.
3. Hold the drive shaft on the left hand side by inserting
the tip of a large-size plain flat head screwdriver into the slotted end of the arbor shaft, and remove the locking nut with an open end wrench.
4. Remove the outer flange, slide off the old wheel and put a new one on.
5. Re-intall the flange and the nut.
6. Position a screwdriver in the slot in the arbor shaft,
and re-tighten the nut on the arbor.
Note: Over tighening can crack the wheel.
7. Re-install the end-plate.
8. Re-install and adjust the tool rests as described in the
“Set-Up and Assembly”.
10
To avoid injury from accidental starting, always turn the switch off and unplug the machine from the power source before changing the wheels.
MAINTENANCE
LUBRICATION
The Bench Grinder has sealed lubricated bearings in the motor housing that do not require any additional lubrication.
CAUTION: Remove and replace grinding wheels if there is any damage at all. FAILURE to replace a damaged wheel can cause serious injury to the operator.
CAUTION: DO NOT USE FLAMMABLE MATERIALS to clean the Bench Grinder. A clean dry rag or brush is all that is needed to remove dust and debris buildup.
Turn the power switch “OFF” and unplug the power cord from its power source prior to any maintenance.
Repairs to the Bench Grinder should be performed by qualified and trained personnel only. Contact your nearest General International dealer for authorized service. Unauthorized repairs or replacement with non-factory parts could cause serious injury to the operator, damage to the Bench Grinder and void the warranty.
RECOMMENDED OPTIONAL ACCESSORIES FOR YOUR GRINDER
Stand #15-700
34” (863 mm). high stand for 6” or 8” bench grinder. Heavy duty cast iron table & base, tubular steel column.
Electronic Earmuffs #99-200
Highly efficient noise reduction to help protect your hearing when operating power tools.
Stand #15-710
34” (863 mm) high stand for 6”, 8” or 10” bench grinders. Heavy duty cast iron table & base, tubular steel column.Water tray Included.
We offer a large variety of products to help you increase productivity, accuracy and safety when using your grinder. Here’s is but a small sampling of the accessories that are available form your local General International dealer.
11
46
35
38
52
52
36
14
40
69
51
55
70
54
50
4
53
13
2
4
68
51
52
39
44
52
37
42
42
42
P
U
L
L
O
UT
TO
L
O
C
K
42
41
01
05
12
06
03
02
04
72
06
07
09
42
2
10
11
2
08
83
84
28
82
14
43
48
42
73
47
49
86
85
12
77
79
81
80
76
78
75
25
62
18
24
23
17
17
21
16
45
56
63
51
60
57
61
71
32
30
33
31
28
29
28
64
67
65
28
58
59
26
29
28
27A
31
30
P
U
L
L
O
U
T
T
O
L
O
C
K
74
15
45
16
6
17
4
22
4
17
19
10
20
25
RO
T
A
TI
O
N
66
67
28
51
65
56
28
60
61
59
63
57
58
62
71
13
14
PARTS LIST
15-660
PART N0. DESCRIPTION SPECIFICATION QTY
15660-01 BASE 1 15660-02 SLEEVE 1 15660-03 STATOR 1 15660-04 ROTOR 1 15660-05 MOTOR FAN 1 15660-06 BEARING 6202ZZ 2 15660-07 INNER MOTOR GUARD (R ) 1 15660-08 SLEEVE SCREW M5X12L 2 15660-09 SCREEN PLATE 1 15660-10 SET SCREW M4X4L 1 15660-11 OUTER MOTOR GUARD (R ) 1 15660-12 OUTER MOTOR GUARD (L) 1 15660-13 SLEEVE SCREW M5X125L 2 15660-14 SPRING WASHER M5 4 15660-15 INNER WHEEL GUARD (R ) 1 15660-16 PHILLIPS HEAD SCREW 1/4"X3/8" 6 15660-17 WHEEL FLANGE 4 15660-18 GRINDING WHEEL GREY - 36 GRIT 1 15660-19 HEX NUT 1/2" 1 15660-20 OUTER WHEEL GUARD (R) 1 15660-21 INNER WHEEL GUARD (L) 1 15660-22 GRINDING WHEEL WHITE - 100 GRIT 1 15660-23 HEX NUT 1/2" 1 15660-24 OUTER WHEEL GUARD (L) 1 15660-25 PHILLIPS HEAD SCREW 3/16"X1/4" 10 15660-26 TOOL REST SUPPORT(R) 1 15660-27A TOOL REST (R) 1 15660-28 FLAT WASHER 1/4"X16 8 15660-29 KNOB 2 15660-30 FLAT WASHER 5/16"X18 4 15660-31 HEX SCREW 5/16"X1/2" 4 15660-32 TOOL REST SUPPORT (L) 1 15660-33 TOOL REST (L) 1 15660-35 CONDENSER 1 15660-36 FIXTURE CLIP 1 15660-37 SWITCH 1 15660-38 PLATE 1 15660-39 STRAIN RELIEF 1 15660-40 QUENCH TRAY 1 15660-41 PHILLIPS HEAD SCREW 3/16"X3/8" 2 15660-42 I.C. BOX ASSEMBLY 5 COMPONENTS 1 15660-43 SET SCREW M3X8L 2 15660-44 SWITCH PLATE 1 15660-45 DIRECTION INDICATOR LABEL 2
15
PARTS LIST
15-660
PART N0. DESCRIPTION SPECIFICATION QTY
15660-46 POWER CORD W/PLUG 1 15660-47 FIBER WASHER 1 15660-48 BASE PLATE 1 15660-49 PHILLIPS HEAD SCREW W/ WASHER 3/16” X 3/8” 2 15660-50 PAD W/WASHER & SCREW 4 15660-51 STRAIN RELIEF BUSHING 5 15660-52 PHILLIPS HEAD SCREW W/ WASHER 3/16"X1/4" 7 15660-53 SPROCKET WASHER M5 1 15660-54 COPPER WASHER 1 15660-55 PHILLIPS HEAD SCREW W/ WASHER 3/16"X1/4" 1 15660-56 EYE SHIELD 2 15660-57 BAYONET CAP 2 15660-58 LIGHT HOLDER 2 15660-59 BULB 2 15660-60 WIRE PLATE 2 15660-61 SELF-TAP. SCREW M3X5L 4 15660-62 LIGHT COVER 2 15660-63 CARRIAGE BOLT 2 15660-64 SPARK GUARD 1 15660-65 KNOB 2 15660-66 SPARK GUARD 1 15660-67 HEX BOLT 2 15660-68 LIGHT WIRE PLATE 1 15660-69 TERMINAL 2 15660-70 TERMINAL 4 15660-71 SELF-TAP. SCREW M3X8L 2 15660-72 PHILLIPS HEAD SCREW M3X10L 2 15660-73 SPEED CONTROLLER LABEL 1 15660-74 NAME PLATE 1 15660-75 WHEEL DRESSER COVER 1 15660-76 DRESSING STONE 1 15660-77 DRESSER HANDLE 1 15660-78 PHILLIPS HEAD SCREW 3/16"X1-1/4" 1 15660-79 HEX NUT 3/8" 1 15660-80 DRESSER HOLDER 1 15660-81 ADHESIVE TAPE 1 15660-82 HEADLESS SCREW 1/4"X20L 2 15660-83 SPRING WASHER 1/4" 2 15660-84 NUT 1/4" 2 15660-85 WIRE (BLACK) 1 15660-86 WIRE (WHITE) 1
IMPORTANT: When ordering replacement parts, always give the model number, serial number of
the machine and part number. Also a brief description of each item and quantity desired.
15-660
8360, Champ-d’Eau, Montreal (Quebec)
Canada H1P 1Y3
Tel.: (514) 326-1161
Fax : (514) 326-5565
Parts & Service
Fax : (514) 326-5555 Order Desk
orderdesk@general.ca
www.general.ca
Loading...