Dewalt D25721, D25763, D25891, D25871, D25723 User Manual

Name: Dewalt D25721
Brand: Dewalt
SKU: 2497050
Rating: 4 (1 reviews)

...

4 (1)

ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE

.......................

USAR EL PRODUCTO.

IINSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE

GARANTÍA.

Si tiene dudas o comentarios, contáctenos.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

1-800-4-DEWALT • www.dewalt.com

INSTRUCTION MANUAL

GUIDE D’UTILISATION

MANUAL DE INSTRUCCIONES

(MAR14) Part No. N392152 D25712, D25721, D25723, D25761, D25763, D25871, D25891

The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme, the “D” shaped air intake grill, the array of pyramids on the handgrip, the kit box configuration, and the array of lozenge-shaped humps on the surface of the tool.

The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in

death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result

in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in

minor or moderate injury. NOTICE: indicates a practice not related to personal injury which, if not avoided, may

result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-D

WARNING: To reduce the risk of injury, read the instruction manual.

General Power Tool Safety Warnings

WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark areas invite accidents. b) Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while operating a power tool. Distractions can

cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not

use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators,

ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the

power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may

result in serious personal injury.

b) Use personal protective equipment. Always wear eye protection. Protective

equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off position before

connecting to power source and/or battery pack, picking up or carrying the tool.

Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on. A wrench or

a key left attached to a rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times. This enables better

control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing

and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

g) If devices are provided for the connection of dust extraction and collection

facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct power tool for your application. The

correct power tool will do the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off. Any power tool

that cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the

power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool

accidentally.

d) Store idle power tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by

poorly maintained power tools.

DEWALT Industrial Tool Co., 701 East Joppa Road, Towson, MD 21286

EWALT

Deﬁ nitions: Safety Guidelines

EWALT (1-800-433-9258).

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

D25712, D25721, D25723 1-7/8" (48 mm) SDS Max Hammer; D25761, D25763 2" (52 mm) SDS Max

Hammer; D25871, D25891 Chipping Hammer

Marteau SDS Max D25712, D25721, D25723 48mm (17/8po); Marteau SDS Max D25761, D25763

52mm (2po); Marteaux burineur D25871, D25891

Martillo SDS Max de 48mm (1-7/8") D25712, D25721, D25723; Martillo SDS Max de 52mm (2") D25761,

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in accordance with these

instructions taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result

in a hazardous situation.

5) SERVICE

a) Have your power tool serviced by a qualified repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained.

Additional Safety Instructions for Rotary Hammers

• Wear ear protectors. Exposure to noise can cause hearing loss.

• Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.

• Hold power tool by insulated gripping surfaces when performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.

• Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control.

• Wear safety goggles or other eye protection. Hammering operations cause chips to fly. Flying particles can cause permanent eye damage. Wear a dust mask or respirator for applications that generate dust. Ear protection may be required for most applications.

• Keep a firm grip on the tool at all times. Do not attempt to operate this tool without holding it with both hands. Operating this tool with one hand will result in loss of control. Breaking through or encountering hard materials such as re-bar may be hazardous as well. Tighten the side handle securely before use.

• Do not operate this tool for long periods of time. Vibration caused by hammer action may be harmful to your hands and arms. Use gloves to provide extra cushion and limit exposure by taking frequent rest periods.

• Do not recondition bits yourself. Chisel reconditioning should be done by an authorized specialist. Improperly reconditioned chisels could cause injury.

• Wear gloves when operating tool or changing bits. Accessible metal parts on the tool and bits may get extremely hot during operation. Small bits of broken material may damage bare hands.

• Never lay the tool down until the bit has come to a complete stop. Moving bits could cause injury.

• Do not strike jammed bits with a hammer to dislodge them. Fragments of metal or material chips could dislodge and cause injury.

• Keep the power cord away from the rotating bit. Do not wrap the cord around any part of your body. An electric cord wrapped around a spinning bit may cause personal injury and loss of control.

• Air vents often cover moving parts and should be avoided. Loose clothes, jewellery or long hair can be caught in moving parts.

• An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety. The smaller the gauge number of the wire, the greater the capacity of the cable, that is 16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. When using more than one extension to make up the total length, be sure each individual extension contains at least the minimum wire size. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

Minimum Gauge for Cord Sets

Volts Total Length of Cord in Feet (meters)

Ampere Rating

More Than

0 6 18 16 16 14

D25763; Martillos cincelador D25871, D25891

face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:

construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and

permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body.

S12.6 (S3.19) during use. Under some conditions and duration of use, noise from this product may contribute to hearing loss.

• The label on your tool may include the following symbols. The symbols and their definitions

610 18161412 10 12 16 16 14 12 12 16 14 12 Not Recommended

WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses. Also use

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratory protection.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber.

other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote

absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disperse dust, which may cause serious and

WARNING: Always wear proper personal hearing protection that conforms to ANSI

are as follows:

V .....................volts A .........................amperes

Hz ...................hertz W ........................watts

min .................minutes

or DC .....direct current or AC/DC......alternating or direct current

...................Class I Construction

...................Class II Construction .......................earthing terminal

…/min ............per minute BPM ...................beats per minute

IPM .................impacts per minute RPM ...................revolutions per minute

SPM ...............strokes per minute sfpm ...................surface feet per minute

Not More

Than

(grounded) n .........................rated speed

(double insulated)

120V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7) 240V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

AWG

or AC .............alternating current

o .......................no load speed

........................safety alert symbol

Motor

Your DEWALT tool is powered by a DEWALT-built motor. Be sure your power supply agrees with the nameplate markings. Voltage decrease of more than 10% will cause loss of power and overheating.

EWALT tools are factory tested.

All D

COMPONENTS (Fig. 1)

WARNING: Never modify the power tool or any part of it. Damage or personal injury could result.

A. Trigger switch (D25712, D25721, D25723,

D25761, D25763) On/off rocker switch (D25871, D25891) B. Lock-on slider (D25712, D25721, D25723,

D25761, D25763) C. Side handle

INTENDED USE

These heavy-duty rotary hammers have been designed for professional hammerdrilling and chipping at various work sites (i.e., construction sites). DO NOT use under wet conditions or in presence of flammable liquids or gases.

These heavy-duty rotary hammers are professional power tools. DO NOT let children come into contact with the tool. Supervision is required when inexperienced operators use this tool.

D. Main handle E. SHOCKS Active Vibration Control

F. Mode selector G. Electronic speed and impact control dial H. Clamp wheel I. Rear side handle position

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of injury, turn unit off and disconnect it from power source before installing and removing accessories, before adjusting or when making repairs. An accidental start-up can cause injury.

Side Handle (Fig. 2–4)

D25712, D25721, D25723, D25761, D25763

WARNING: To reduce the risk of personal injury, ALWAYS operate the tool with the side handle

properly installed and securely tightened. Failure to do so may result in the side handle slipping during tool operation and subsequent loss of control. Hold tool with both hands to maximize control.

The side handle clamps to the front barrel (collar) and may be rotated 360° to permit right- or lefthand use. For operating convenience, the side handle can be installed in front or rear positions.

TO MOUNT IN FRONT POSITION (FIG. 2)

1. Unscrew the side handle (C) and disassemble the side handle clamp (J).

2. Snap the steel ring (K) over the collar (L) behind the tool holder (M). Squeeze both ends of the

steel ring together. Mount the bushing (N) and insert the pin (O).

3. Slide the side handle clamp (J) onto the bushing (N) while keeping the pin (O) centered. Lightly

screw the clamp wheel (H) onto the busing (N)—do not tighten.

4. Screw the side handle (C) into the clamp wheel (H) and tighten.

5. Rotate the side handle mounting assembly to the desired position. For hammerdrilling

horizontally with a heavy drill bit, place the side handle assembly at an angle of approximately 20° to the tool for optimum control.

6. Lock the side handle mounting assembly in place by securely tightening the clamp wheel (H)

so that the assembly will not rotate.

TO MOUNT IN REAR POSITION (FIG. 3)

1. Unscrew the side handle (C) and remove it from the side handle mounting assembly. Leave the

side handle mounting assembly in the front position.

2. Screw the side handle directly into one of the rear side handle positions (I) on either side of the

tool.

D25871, D25891 (FIG. 4)

1. Unscrew the D-shaped handle knob (Q).

FIG. 1

HAMMERDRILLING MODE

MODE DE MARTEAU PERFORATEUR

MODO TALADRO PERCUTOR

FIG. 2

FIG. 5

FIG. 6

R S V

FIG. 4

CHISEL BIT ADJUSTMENT MODE

MODE DE RÉGLAGE DU TRÉPAN ORDINAIRE

MODO DE AJUSTE DE LA BROCA DE CINCEL

MODE DE BURINAGE

CHISEL BIT ADJUSTMENT MODE

MODE DE RÉGLAGE DU TRÉPAN ORDINAIRE

MODO DE AJUSTE DE LA BROCA DE CINCEL

FIG. 3

D25712 D25721 D25723 D25761 D25763

D25871 D25891

FIG. 7

D25712 D25721 D25723 D25761 D25763

D25871 D25891

CHIPPING MODE

MODO CINCEL

2. Slide the D-shaped handle assembly over the tool holder (M) and onto the collar (L) in the mounting area (W). The correct position of the D-shaped handle (X) is between head and middle of the tube.

3. Adjust the D-shaped handle to the desired angle.

4. Slide and rotate the D-shaped handle to the desired position.

5. Lock the D-shaped handle in place by securely tightening the knob (Q) so that the D-shaped handle assembly will not rotate.

SHOCKS Active Vibration Control® System (Fig. 1, 7)

For best vibration control, hold the tool with one hand on the main handle (D) and the other hand on the side handle (C) or D-shaped handle (X). Apply just enough pressure so the hammer is approximately mid-stroke. The hammer only needs enough pressure to engage the SHOCKS Active Vibration Control faster and the SHOCKS Active Vibration Control

system. Applying too much pressure will not make the tool drill or chip

system will not engage.

Inserting and Removing SDS Max Accessories (Fig. 5)

1. Pull back the locking sleeve (P) and insert the bit shank. The bit shank must be clean and slightly lubricated.

2. Turn the bit slightly until the sleeve snaps back into position.

3. Ensure the bit is properly engaged. NOTE: The bit needs to move several centimeters in and out of the tool holder (M) when

properly engaged.

4. To remove the bit, pull back the locking sleeve and pull the bit out.

Two-Stage Clutch/E-ClutchTM (Fig. 6)

NOTICE: Always turn the tool off before changing torque control settings or damage to tool may result.

TWO-STAGE CLUTCH D25712, D25723, D25763

Clutch Setting 1 (R) is designed for most hammerdrilling applications and is designed to easily clutch out when the drill bit encounters re-bar or other foreign substances.

Clutch Setting 2 (S) is designed for higher torque applications such as core-bits and deep hole hammerdrilling and is designed to clutch out at a higher torque threshold.

Move the torque control lever (V) to Clutch Setting 1 or 2 as needed for application.

NOTE: Allow the motor housing to rotate a little while changing torque. NOTE: If it is not possible to select Clutch Setting 2, run the unit under load and try again.

Each time the tool is plugged in, it will automatically default to Clutch Setting 1, the most sensitive setting.

E-CLUTCH™ D25723, D25763

In addition, E-Clutch™ offers increased user comfort and safety through an on-board antirotation technology capable of detecting if the user loses control of the hammer. When a jam is detected, the torque and speed are reduced instantly. The red indicator LED (T) illuminates when E-Clutch™ is engaged.

Electronic Speed and Impact Control (Fig. 6)

The electronic speed and impact control allows the use of smaller drill bits without the risk of bit breakage, hammerdrilling into light and brittle materials without shattering and optimal tool control for precise chiseling.

To set the control dial, turn the dial (G) to the desired level. The higher the number, the greater the speed and impact energy. Dial settings make the tool extremely flexible and adaptable for many different appli cations. The required setting depends on the bit size and hardness of material being drilled.

Mode Selector (Fig. 1)

NOTICE: Never change the mode while the unit is running. Tool must come to a complete stop before activating the mode selector button or damage to the tool may result.

CAUTION: Do not change to hammerdrill mode with chisel bit in tool holder. Personal injury and

damage to tool may result.

The D25712, D25721, D25723, D25761, D25763 use two operating modes. To select the required operating mode, rotate the mode selector (F) until the arrow points to the hammerdrilling or the chipping icon. The D25871 and D25891 use only the chipping mode.

HAMMERDRILLING MODE (

)

D25712, D25721, D25723, D25761, D25763

The tool simultaneously rotates and impacts the work. This mode is appropriate for all concrete and masonry operations.

CHIPPING MODE (

)

D25871, D25891

The spindle lock is engaged during chipping mode so the tool impacts the work without rotating. This mode is appropriate for light chipping, chiseling and demolition applications.

NOTE: In chipping mode, the hammerdrill can also be used as a lever to free a jammed drill bit. CHISEL BIT ADJUSTMENT (

)

Turn the mode selector to one of the chisel bit adjustment icons to adjust the chisel to the desired position. There are multiple positions to set the angle of the chisel. After finding the desired position, slightly maneuver the chisel bit back and forth to ensure the chisel is properly engaged.

Indicator Lights (Fig. 1, 6)

The yellow brush wear indicator LED (U) lights up when the carbon brushes are nearly worn out indicating that the tool needs servicing within the next 8 hours of use.

The red indicator LED (T) lights up if the lock-on slider (B) and/or E-Clutch™ is engaged in any mode except the chipping mode.

The red indicator LED (T) starts to flash if there is a fault with the tool or the brushes have completely worn out (refer to Repairs under Maintenance).

INDICATOR DIAGNOSIS SOLUTION

OFF Tool is functioning

normally

SOLID Perform and protect

control has been activated

Follow all warnings and instructions when operating tool

With tool properly supported, release trigger; the tool will function normally when the trigger is depressed again and the indicator light will go out

FLASHING Perform and

protect control is

Take the tool to an authorized

EWALT repair agent.

malfunctioning

NOTE: If the tool power is insufficient for normal hammering and if the LED does not flash repeatedly after cycling the trigger, take the tool to an authorized D

EWALT repair center.

OPERATION

WARNING: To reduce the risk of personal injury, ALWAYS ensure workpiece is anchored or clamped firmly. If hammerdrilling thin material, use a wood “back-up” block to prevent damage

to the material.

WARNING: To reduce the risk of personal injury, ALWAYS operate the tool with the side handle properly installed and securely tightened. Failure to do so may result in the side

handle slipping during tool operation and subsequent loss of control. Hold tool with both hands to maximize control.

WARNING: Drill may stall if overloaded causing a sudden twist. Always expect the stall. Grip the drill firmly with both hands to control the twisting action and avoid injury.

Proper Hand Position (Fig. 7)

WARNING: To reduce the risk of serious personal injury, ALWAYS use proper hand position as shown in Figure 7.

WARNING: To reduce the risk of serious personal injury, ALWAYS hold securely in anticipation of a sudden reaction.

Proper hand position requires one hand on the side handle (C) or D-shaped handle (X), with the other hand on the main handle (D).

NOTE: Operating temperature of this tool is 19˚ to 104˚ F (-7 to +40˚ C). Using the tool outside of this temperature range will decrease the life of the tool.

Trigger Switch (Fig. 1)

D25712, D25721, D25723, D25761, D25763

To turn the tool on, depress the trigger switch (A). To stop the tool, release the trigger switch. In chipping mode only, lock the trigger switch on by pushing the lock-on slider (B) upward while

depressing the trigger switch. To deactivate the lock-on slider, depress the trigger switch once then release. The lock-on slider may only be activated in chipping mode. The machine will stop running when

trying to engage the lock-on slider in hammerdrilling mode. The motor will stop if the lock-on slider is activated when changing from chisel mode into hammerdrilling mode.

D25871, D25891

For continuous operation, move the rocker switch to the on position. To stop continuous operation, move the rocker switch to the off position.

SOFT START FEATURE

The soft start feature allows you to build up speed slowly, thus preventing the drill bit from walking off the intended hole position when starting. The soft start feature also reduces the immediate torque reaction transmitted to the gearing and the operator if the hammer is started with the drill bit in an existing hole.

Hammerdrilling (Fig. 1)

Set the mode selector (F) to hammerdrilling mode.

1. When hammerdrilling, use just enough force on the hammer to keep it from bouncing

excessively or “rising” off the bit. Too much force will cause slower hammerdrilling speeds and overheating.

2. Drill straight, keeping the bit at a right angle to the work. Do not exert side pressure on the bit

when hammerdrilling as this will cause clogging of the bit flutes and a slower hammerdrilling speed.

3. When hammerdrilling deep holes, if the hammer speed starts to drop off, pull the bit partially

out of the hole with the tool still running to help clear debris from the hole.

4. For masonry, use carbide-tipped bits or masonry bits. A smooth even flow of dust indicates the

proper hammerdrilling rate.

HAMMERDRILLING WITH A SOLID BIT (FIG. 1, 6) D25712, D25721, D25723, D25761, D25763 NOTE: The D25871 and D25891 have only chipping modes with no hammerdrilling capability.

1. Set the mode selector (F) to hammerdrilling mode.

2. For D25723 and D25763 only, move the torque control lever (V) to Setting 1 (R).

3. Set the speed and impact control dial (G).

4. Insert the appropriate drill bit.

5. Adjust the side handle (front or rear position).

6. Mark the spot where the hole is to be drilled.

7. Place the drill bit on that mark and depress the trigger switch (A).

8. Apply only enough pressure to engage active vibration control (refer to SHOCKS Active

Vibration Control

9. To stop the tool, release the trigger switch. Always turn the tool off when work is finished and

before unplugging.

HAMMERDRILLING WITH A CORE BIT (FIG. 1, 6) D25712, D25721, D25723, D25761, D25763

CAUTION: Do not use a core bit for hammerdrilling wood. Personal injury and damage to tool

may result.

NOTE: The D25871 and D25891 have only chipping modes with no hammerdrilling capability.

1. Set the mode selector (F) to hammerdrilling mode.

2. For D25723 and D25763 only, move the torque control lever (V) to Setting 2 (S).

3. Turn the speed and impact control dial (G) to a desired speed position.

4. Adjust the side handle (front or rear position).

5. Assemble the centering bit and adapter shank into the core bit and insert into tool.

6. Mark the spot where the hole is to be drilled.

7. Place the centering bit on that mark and depress the trigger switch. NOTE: Some core drills require the removal of centering bit after about 1 cm of penetration. If

so, remove and continue hammerdrilling.

8. When hammerdrilling through a structure thicker than the depth of the core bit, break away

the round cylinder of concrete or core inside the bit at regular intervals. To avoid unwanted breaking away of concrete around the hole, first drill a hole the diameter of the centering bit

System).

completely through the structure. Then drill the cored hole halfway from each side of the structure.

9. To stop the tool, release the trigger switch. Always turn the tool off when work is finished and before unplugging.

Chipping and Chiseling

D25871, D25891

1. Set the mode selector to chipping mode.

2. Set the impact control dial to desired setting (refer to Electronic Speed and Impact Control).

3. Insert the appropriate chisel and rotate it by hand to lock it into the desired position.

NOTE: For SDS Max models, only use SDS Max bits.

4. Adjust the side handle (front or rear position).

5. Depress the trigger switch.

6. Apply only enough pressure to engage active vibration control (refer to SHOCKS Active

Vibration Control

7. To stop the tool, release the trigger switch. Always turn the tool off when work is finished and before unplugging.

System).

MAINTENANCE

Motor Brushes

DEWALT uses an advanced brush system which automatically stops the drill when the brushes wear out. This prevents serious damage to the motor. New brush assemblies are available at authorized D

EWALT service centers. Always use identical replacement parts.

Cleaning

WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a week. To minimize the risk of eye injury, always wear ANSI Z87.1 approved eye protection when performing this.

WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts of the tool. These chemicals may weaken the plastic materials used in these parts. Use a cloth dampened only with water and mild soap. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.

Lubrication

Your tool was properly lubricated before leaving the factory. In two to six months, depending upon use, take or send your tool to an authorized service center for a complete cleaning, inspection and lubrication. Tools used constantly on production jobs will need relubrication more often. Also, tools “out of service” for long periods should be relubricated before being put back to work.

Accessories

WARNING: Since accessories, other than those offered by DEWALT, have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only D

EWALT recommended accessories should be used with this product.

Recommended accessories for use with your tool are available at extra cost from your local dealer or authorized service center. If you need assistance in locating any accessory, please contact D Industrial Tool Co., 701 East Joppa Road, Towson, MD 21286, call 1-800-4-DEWALT (1-800-433-

9258) or visit our website: www.dewalt.com.

MAXIMUM CAPACITY

D25712 D25721 D25723

Concrete 1-7/8" (48 mm) 2" (52 mm) – – RPM 137–275 125–250 – – No load BPM 1260–2520 1150–2300 1260–2520 1150–2300

D25761 D25763 D25871 D25891

EWALT

Repairs

To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including brush inspection and replacement) should be performed by a D authorized service center or other qualified service personnel. Always use identical replacement parts.

EWALT factory service center, a DEWALT

Thank you for your purchase. Register your product now for:

• WARRANTY SERVICE: Registering your product will help you obtain more efficient warranty

service in case there is a problem with your product.

• CONFIRMATION OF OWNERSHIP: In case of an insurance loss, such as fire, flood or theft,

your registration of ownership will serve as your proof of purchase.

• FOR YOUR SAFETY: Registering your product will allow us to contact you in the unlikely event

a safety notification is required under the Federal Consumer Safety Act.

Three Year Limited Warranty

DEWALT will repair, without charge, any defects due to faulty materials or workmanship for three years from the date of purchase. This warranty does not cover part failure due to normal wear or tool abuse. For further detail of warranty coverage and warranty repair information, visit www.dewalt. com or call 1-800-4-D damage caused where repairs have been made or attempted by others. This warranty gives you specific legal rights and you may have other rights which vary in certain states or provinces.

In addition to the warranty, D

EWALT will maintain the tool and replace worn parts caused by normal use, for free, any time

during the first year after purchase.

If you are not completely satisfied with the performance of your D for any reason, you can return it within 90 days from the date of purchase with a receipt for a full refund – no questions asked.

LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products sold in Latin America, see country specific warranty information contained in the packaging, call the local company or see website for warranty information.

FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call 1-800-4-D

EWALT (1-800-433-9258) for a free replacement.

EWALT (1-800-433-9258). This warranty does not apply to accessories or

EWALT tools are covered by our:

1 YEAR FREE SERVICE

90 DAY MONEY BACK GUARANTEE

EWALT Power Tool, Laser, or Nailer

Déﬁ nitions: lignes directrices en

matière de sécurité

Les définitions ci-dessous décrivent le niveau de danger pour chaque mot-indicateur employé. Lire le mode d’emploi et porter une attention particulière à ces symboles.

DANGER: indique une situation dangereuse imminente qui, si elle n’est pas

évitée, entraînera la mort ou des blessures graves.

AVERTISSEMENT : indique une situation potentiellement dangereuse qui,

si elle n’est pas évitée, pourrait entraîner la mort ou des blessures graves.

ATTENTION : indique une situation potentiellement dangereuse qui, si elle

n’est pas évitée, pourrait entraîner des blessures légères ou modérées. AVIS : indique une pratique ne posant aucun risque de dommages corporels

mais qui par contre, si rien n’est fait pour l’éviter, pourrait poser des risques de

dommages matériels.

POUR TOUTE QUESTION OU REMARQUE AU SUJET DE CET OUTIL OU DE TOUT AUTRE OUTIL D

Avertissements de sécurité généraux pour les outils électriques

EWALT, COMPOSEZ LE NUMÉRO SANS FRAIS : 1-800-4-DEWALT (1-800-433-9258).

AVERTISSEMENT : afin de réduire le risque de blessures, lire le mode d’emploi de l’outil.

AVERTISSEMENT ! Lire tous les avertissements de sécurité et toutes les directives. Le non-respect des avertissements et des directives pourrait se solder par un choc électrique, un incendie et/ou une blessure grave.

CONSERVER TOUS LES AVERTISSEMENTS ET TOUTES LES

DIRECTIVES POUR UN USAGE ULTÉRIEUR

Le terme « outil électrique » cité dans les avertissements se rapporte à votre outil électrique à alimentation sur secteur (avec fil) ou par piles (sans fil).

1) SÉCURITÉ DU LIEU DE TRAVAIL

a) Tenir l’aire de travail propre et bien éclairée. Les lieux encombrés ou sombres sont

propices aux accidents.

b) Ne pas faire fonctionner d’outils électriques dans un milieu déflagrant, tel qu’en

présence de liquides, de gaz ou de poussières inflammables. Les outils électriques produisent des étincelles qui pourraient enflammer la poussière ou les vapeurs.

c) Éloigner les enfants et les personnes à proximité pendant l’utilisation d’un outil

électrique. Une distraction pourrait en faire perdre la maîtrise à l’utilisateur.

2) SÉCURITÉ EN MATIÈRE D’ÉLECTRICITÉ

a) Les fiches des outils électriques doivent correspondre à la prise. Ne jamais modifier

la fiche d’aucune façon. Ne jamais utiliser de fiche d’adaptation avec un outil électrique mis à la terre. Le risque de choc électrique sera réduit par l’utilisation de fiches

non modifiées correspondant à la prise.

b) Éviter tout contact physique avec des surfaces mises à la terre comme des tuyaux,

des radiateurs, des cuisinières et des réfrigérateurs. Le risque de choc électrique est plus élevé si votre corps est mis à la terre.

c) Ne pas exposer les outils électriques à la pluie ou à l’humidité. La pénétration de l’eau

dans un outil électrique augmente le risque de choc électrique.

d) Ne pas utiliser le cordon de façon abusive. Ne jamais utiliser le cordon pour

transporter, tirer ou débrancher un outil électrique. Tenir le cordon éloigné de la chaleur, de l’huile, des bords tranchants et des pièces mobiles. Les cordons

endommagés ou enchevêtrés augmentent les risques de choc électrique.

e) Pour l’utilisation d’un outil électrique à l’extérieur, se servir d’une rallonge

convenant à cette application. L’utilisation d’une rallonge conçue pour l’extérieur réduira les risques de choc électrique.

f) S’il est impossible d’éviter l’utilisation d’un outil électrique dans un endroit

humide, brancher l’outil dans une prise ou sur un circuit d’alimentation dotés d’un disjoncteur de fuite à la terre (GFCI). L’utilisation de ce type de disjoncteur réduit les

risques de choc électrique.

3) SÉCURITÉ PERSONNELLE

a) Être vigilant, surveiller le travail effectué et faire preuve de jugement lorsqu’un outil

électrique est utilisé. Ne pas utiliser d’outil électrique en cas de fatigue ou sous l’influence de drogues, d’alcool ou de médicaments. Un simple moment d’inattention

en utilisant un outil électrique peut entraîner des blessures corporelles graves.

b) Utiliser des équipements de protection individuelle. Toujours porter une protection

oculaire. L’utilisation d’équipements de protection comme un masque antipoussière, des chaussures antidérapantes, un casque de sécurité ou des protecteurs auditifs lorsque la situation le requiert réduira les risques de blessures corporelles.

c) Empêcher les démarrages intempestifs. S’assurer que l’interrupteur se trouve à la

position d’arrêt avant de relier l’outil à une source d’alimentation et/ou d’insérer un bloc-piles, de ramasser ou de transporter l’outil. Transporter un outil électrique alors

que le doigt repose sur l’interrupteur ou brancher un outil électrique dont l’interrupteur est à la position de marche risque de provoquer un accident.

d) Retirer toute clé de réglage ou clé avant de démarrer l’outil. Une clé ou une clé de

réglage attachée à une partie pivotante de l’outil électrique peut provoquer des blessures corporelles.

e) Ne pas trop tendre les bras. Conserver son équilibre en tout temps. Cela permet de

mieux maîtriser l’outil électrique dans les situations imprévues.

f) S’habiller de manière appropriée. Ne pas porter de vêtements amples ni de bijoux.

Garder les cheveux, les vêtements et les gants à l’écart des pièces mobiles. Les vêtements amples, les bijoux ou les cheveux longs risquent de rester coincés dans les pièces mobiles.

g) Si des composants sont fournis pour le raccordement de dispositifs de dépoussiérage

et de ramassage, s’assurer que ceux-ci sont bien raccordés et utilisés. L’utilisation d’un dispositif de dépoussiérage peut réduire les dangers engendrés par les poussières.

4) UTILISATION ET ENTRETIEN D’UN OUTIL ÉLECTRIQUE

a) Ne pas forcer un outil électrique. Utiliser l’outil électrique approprié à l’application.

L’outil électrique approprié effectuera un meilleur travail, de façon plus sûre et à la vitesse pour laquelle il a été conçu.

b) Ne pas utiliser un outil électrique dont l’interrupteur est défectueux. Tout outil

électrique dont l’interrupteur est défectueux est dangereux et doit être réparé.

c) Débrancher la fiche de la source d’alimentation et/ou du bloc-piles de l’outil

électrique avant de faire tout réglage ou changement d’accessoire ou avant de ranger l’outil. Ces mesures préventives réduisent les risques de démarrage accidentel de

l’outil électrique.

d) Ranger les outils électriques hors de la portée des enfants et ne permettre à

aucune personne n’étant pas familière avec un outil électrique ou son mode d’emploi d’utiliser cet outil. Les outils électriques deviennent dangereux entre les mains

d’utilisateurs inexpérimentés.

e) Entretien des outils électriques. Vérifier si les pièces mobiles sont mal alignées ou

coincées, si des pièces sont brisées ou présentent toute autre condition susceptible de nuire au bon fonctionnement de l’outil électrique. En cas de dommage, faire réparer l’outil électrique avant toute nouvelle utilisation. Beaucoup d’accidents sont

causés par des outils électriques mal entretenus.

f) S’assurer que les outils de coupe sont aiguisés et propres. Les outils de coupe bien

entretenus et affûtés sont moins susceptibles de se coincer et sont plus faciles à maîtriser.

g) Utiliser l’outil électrique, les accessoires, les forets, etc. conformément aux

présentes directives en tenant compte des conditions de travail et du travail à effectuer. L’utilisation d’un outil électrique pour toute opération autre que celle pour laquelle

il a été conçu est dangereuse.

5) RÉPARATION

a) Faire réparer l’outil électrique par un réparateur professionnel en n’utilisant que

des pièces de rechange identiques. Cela permettra de maintenir une utilisation sécuritaire

de l’outil électrique.

Consignes de sécurité additionnelles propres aux marteaux rotatifs

• Porter un dispositif de protection auditif. Le bruit en résultant pourrait occasionner une

perte de l’acuité auditive.

• Utiliser la/les poignée(s) auxiliaire(s) si fournie(s) avec l’outil. Une perte de contrôle de

l’outil pourrait occasionner des dommages corporels.

• Tenir l’outil électrique par les surfaces isolées prévues à cet effet pendant toute

utilisation où l’organe de coupe pourrait entrer en contact avec des fils électriques cachés ou son propre cordon. Tout contact de l’organe de coupe avec un fil sous tension

mettra les parties métalliques exposées de l’outil électrique sous tension et électrocutera l’utilisateur.

• Utiliser des serre-joints, ou tout autre moyen, pour fixer et immobiliser le matériau sur une surface stable. Tenir la pièce à la main ou contre son corps offre une stabilité insuffisante qui pourrait vous en faire perdre le contrôle.

• Porter des lunettes de protection ou toute autre protection oculaire. Le martelage pourrait faire voltiger des éclats. Ces particules volantes pourraient occasionner des dommages oculaires permanents. Porter un masque anti-poussières ou un appareil de protection des voies respiratoires pour toute application productrice de poussières. Une protection auditive peut s’avérer nécessaire pour la plupart des applications.

• Maintenir systématiquement l’outil fermement. Ne pas tenter d’utiliser cet outil sans le maintenir à deux mains. Le fait d’utiliser cet outil à une main pourra vous en faire perdre le contrôle. Traverser ou rencontrer des matériaux durs comme les armatures peut aussi s’avérer dangereux. Resserrer soigneusement la poignée latérale avant toute utilisation.

• Ne pas utiliser cet outil pendant des périodes de temps prolongées. Les vibrations causées par la percussion peuvent poser des risques pour les mains ou les bras. Porter des gants pour amortir les vibrations, et pour limiter les risques, faire des pauses fréquentes.

• Ne pas remettre à neuf les forets soi-même. La remise à neuf de tout burin doit être effectuée par un spécialiste agréé. Tout burin remis à neuf incorrectement pose des risques de dommages corporels.

• Porter des gants lors de l’utilisation de l’outil ou le changement de mèche. Les parties métalliques accessibles de l’outil et des mèches/forets pourraient s’avérer brûlantes lors de l’utilisation. De petits débris de matériau pourraient aussi blesser les mains nues.

• Attendre systématiquement l’arrêt complet de la mèche/foret avant de déposer l’outil où que ce soit. Des forets/mèches en rotation posent des risques de dommages corporels.

• Ne pas donner des coups de marteau sur des forets/mèches coincés pour les déloger. Des fragments de métal ou de matériau pourraient être éjectés et causer des dommages corporels.

• Maintenir le cordon d’alimentation à l’écart d’une mèche en rotation. Ne pas enrouler le cordon autour d’une partie quelconque de votre corps. Un cordon électrique enroulé autour d’une mèche en rotation pose des risques de dommages corporels et de perdre le contrôle de l’outil.

• Prendre des précautions à proximité des évents, car ils cachent des pièces mobiles. Vêtements amples, bijoux ou cheveux longs risquent de rester coincés dans ces pièces mobiles.

• Pour la sécurité de l’utilisateur, utiliser une rallonge de calibre adéquat (AWG, American Wire Gauge [calibrage américain normalisé des fils électriques]). Plus le calibre est petit, et plus sa capacité est grande. Un calibre16, par exemple, a une capacité supérieure à un calibre18. L’usage d’une rallonge de calibre insuffisant causera une chute de tension qui entraînera perte de puissance et surchauffe. Si plus d’une rallonge est utilisée pour obtenir une certaine longueur, s’assurer que chaque rallonge présente au moins le calibre de fil minimum. Le tableau ci-dessous illustre les calibres à utiliser selon la longueur de rallonge et l’intensité nominale indiquée sur la plaque signalétique. En cas de doute, utiliser le calibre suivant. Plus le calibre est petit, plus la rallonge peut supporter de courant.

Calibres minimaux des rallonges

Intensité (en ampères)

Supérieur à Inférieur à AWG

0 6 18 16 16 14

610 18161412 10 12 16 16 14 12 12 16 14 12 Non recommandé

AVERTISSEMENT: porter SYSTEMATIQUEMENT des lunettes de protection. Les lunettes

courantes NE sont PAS des lunettes de protection. Utiliser aussi un masque antipoussières si la découpe doit en produire beaucoup. PORTER SYSTÉMATIQUEMENT UN ÉQUIPEMENT DE SÉCURITÉ HOMOLOGUÉ:

volts Longueur totale de cordon en mètres (pieds) 120 V 7,6 (25) 15,2 (50) 30,5 (100) 45,7 (150) 240 V 15,2 (50) 30,5 (100) 61,0 (200) 91,4 (300)

+ 4 hidden pages