BEKO WTV77111BW0 User Manual [fr]

Washing Machine

User Manual

Waschmaschine

Bedienungsanleitung

Lave-linge

Manuel d‘utilisation

WTV 7711 BW0

EN / DE / FR

Document Number= 2820526731_EN / 12-03-18.(17:21)

This product was manufactured using the latest technology in environmentally friendly conditions.

1 General safety instructions

This section includes security instructions which may help prevent the injuries and material damage risks. All kinds of warranties shall be invalid if these instructions are not observed.

1.1 Life and property safety

u Never place the product on a carpet-covered floor. Electrical parts will get overheated since air cannot circulate from under the device. This will cause problems with your product.

u Unplug the product if it is not in use.

u Always have the installation and repairing procedures carried out by the Authorised Service Agent. The manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorised persons.

u The water supply and draining hoses must be securely fastened and remain undamaged. Otherwise, water leak may occur.

u While there is still water inside the product, never open the loading door or remove the filter. Otherwise, risk of flooding and injury from hot water will occur.

u Do not force open the locked loading door. Door can be opened a few minutes after the washing cycle ends. In case of forcing the loading door to open, the door and the lock mechanism may get damaged.

u Use detergents, softeners and supplements suitable for automatic washing machines only.

u Follow the instructions on the label of textiles and the detergent package.

1.2 Children's safety

u This product can be used by the children who are at the age of 8 and over and the people whose physical, sensory or mental skills are not fully developed or who do not have necessary required experience and knowledge as long as they are supervised or trained about the safe use of the product and its risks. Children should not play with the device. Cleaning and maintenance works should not be performed by children unless they are supervised by someone. Children of less than 3 years should be kept away unless continuously supervised.

u Packaging materials may be dangerous for the children. Keep packaging materials in a safe place away from reach of the children.

Washing Machine / User’s Manual

3 / EN

uElectrical products are dangerous for the children. Keep the children away from the product when it is in use. Do not allow them to play with the product. Use child lock to prevent children from intervening with the product.

uDo not forget to close the loading door when leaving the room where the product is located.

uStore all detergents and additives in a safe place away from the reach of the children by closing the cover of the detergent container or sealing the detergent package.

1.3Electrical safety

uIf the product has a failure, it should not be operated unless it is repaired by the Authorised Service Agent. Risk of electric shock!

uThis product is designed to resume operating in the event of powering on after a power interruption. If you wish to cancel the programme, see "Cancelling the programme" section.

uPlug the product into a grounded outlet protected by a 16 A fuse. Do not neglect to have the grounding installation made by a qualified electrician. Our company shall not be liable for any damages that will arise when the product is used without grounding in accordance with the local regulations.

uDo not wash the product by spraying or pouring water onto it! Risk of electric shock!

uNever touch the power cable plug with wet hands! Do not grab the power cord to unplug the machine, always unplug it by holding the socket with one hand, and pulling the plug with the other hand.

uProduct should be unplugged during installation, maintenance, cleaning and repair procedures.

uIf the power cable is damaged, it must be replaced by the manufacturer, after sales service or a similarly qualified person (preferably an electrician) or someone designated by the importer in order to avoid possible risks.

1.4Hot surface safety

While washing the laundry at high temperatures, the loading door glass will get hot. Considering this fact, during washing operation keep the children away from the loading door of the product to prevent them touching it.

4 / EN

Washing Machine / User’s Manual

2 Important instructions for environment

2.1 Compliance with WEEE Directive

This product complies with EU WEEE Directive (2012/19/EU). This product bears a classification symbol for waste electrical and electronic equipment (WEEE).

This product has been manufactured with high quality parts and materials which can be reused and are suitable for recycling. Do not dispose of the waste product with normal domestic and other wastes at the end of its service life. Take it to the collection center for the recycling of electrical and electronic equipment. Please consult your local authorities to learn about these collection centers.

Compliance with RoHS Directive:

The product you have purchased complies with EU RoHS Directive (2011/65/EU). It does not contain harmful and prohibited materials specified in the Directive.

2.2 Package information

Packaging materials of the product are manufactured from recyclable materials in accordance with our National Environment Regulations. Do not dispose of the packaging materials together with the domestic or other wastes. Take them to the packaging material collection points designated by the local authorities.

3Intended use

•Thisproducthasbeendesignedfordomesticuse.Itisnotforcommercial purposes or it should not be used out of its intended use.

•Theproductmustonlybeusedforwashingandrinsingoflaundrythatare marked accordingly.

•Themanufacturerwaivesanyresponsibilityarisenfromincorrectusageor transportation.

•Theservicelifeofyourproductis10years.Duringthisperiod,originalspare parts will be available to operate the appliance properly.

Washing Machine / User’s Manual

5 / EN

4		Technical specifications
Complying Commission Delegated Regulation (EU) No 1061/2010
Supplier name or trademark				Beko
Model name				WTV 7711 BW0
Rated capacity (kg)				7
Energy efficiency class / Scale from A+++ (Highest Efficiency) to D (Lowest Efficiency)				A+++
Annual Energy Consumption (kWh) (1)				173
Energy consumption of the standard 60°C cotton programme at full load (kWh)				0,888
Energy consumption of the standard 60°C cotton programme at partial load			(kWh)	0,680
Energy consumption of the standard 40°C cotton programme at partial load			(kWh)	0,680
Power consumption in ‘off-mode’ (W)				0,250
Power consumption in ‘left-on mode’ (W)				0,750
Annual Water Consumption (l) (2)				10119
Spin-drying efficiency class / Scale from A (Highest Efficiency) to G (Lowest Efficiency)				B
Maximum spin speed (rpm)				1400
Remaining moisture Content (%)				53
Standard cotton programme (3)				Cotton Eco 60°C and 40°C
Programme time of the standard 60°C cotton programme at full load (min)				225
Programme time of the standard 60°C cotton programme at partial load (min)				195
Programme time of the standard 40°C cotton programme at partial load (min)				170
Duration of the left-on mode (min)				N/A
Airborne acoustical noise emissions washing/spinning (dB)				60/76
Built-in				No
Height (cm)				84
Width (cm)				60
Depth (cm)				55
Net weight (±4 kg.)				70
Single Water inlet / Double Water inlet				• / -
• Available
Electrical input (V/Hz)				230 V / 50Hz
Total current (A)				10
Total power (W)				2200
Main model code				9210

(1)Energy Consumption based on 220 standard washing cycles for cotton programmes at 60°C and 40°C at full and partial load, and the consumption of the low-power modes. Actual energy consumption will depend on how the appliance is used.

(2)Water consumption based on 220 standard washing cycles for cotton programmes at 60°C and 40°C at full and partial load. Actual water consumption will depend on how the appliance is used.

(3)“Standard 60°C cotton programme” and the “standard 40°C cotton programme” are the standard washing programmes to which the information in the label and the fiche relates and these programmes are suitable to clean normally soiled cotton laundry and that they are the most efficient programmes in terms of combined energy and water consumption.

Technical specifications may be changed without prior notice to improve the quality of the product.

6 / EN

Washing Machine / User’s Manual

4.1 Installation

•Applytothenearestauthorisedserviceagentfortheinstallationofyourproduct.

•Preparationofthelocationandelectrical,tapwaterandwastewaterinstallationsattheplaceof installation is under customer's responsibility.

•Makesurethatthewaterinletanddischargehosesaswellasthepowercablearenotfolded, pinched or crushed while pushing the product into its place after installation or cleaning procedures.

•Makesurethattheinstallationandelectricalconnectionsoftheproductareperformedby authorised service. Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorised persons.

•Priortoinstallation,visuallycheckiftheproducthasanydefectsonit.Ifso,donothaveitinstalled.

Damaged products cause risks for your safety.

4.1.1Appropriate installation location

•Placetheproductonahardandlevelfloor.Donotputitontoacarpetwithhighpileorother similar surfaces.

•Whenthewashingmachineanddryerareplacedontopofeachother,theirtotalweight–when loaded–amountsto180kilograms.Placetheproductonasolidandflatfloorthathassufficient load carrying capacity!

•Donotplacetheproductonthepowercable.

•Donotinstalltheproductintheenvironmentswherethetemperaturefallsbelow0ºC.

•Leavingagapatthesidesofthemachineissuggestedtoreducevibrationandnoise

•Onagraduatedfloor,donotplacetheproductnexttotheedgeoronaplatform.

•DonotplaceheatsourcessuchasHobs,Irons,Ovens,etc.onthewashingmachineanddonotuse them on the product.

4.1.2Removing packaging reinforcement

Tilt the machine backwards to remove the packaging reinforcement. Remove the packaging reinforcement by pulling the ribbon. Do not make this operation alone by yourself.

4.1.3 Removing the transportation locks

1 Loosenallboltswithanappropriatewrenchuntiltheyturnfreely.

2 Remove the transport safety bolts by turning them slightly.

3 Insert the plastic covers in the bag containing the user manual to the openings on the rear panel.

A CAUTION: Remove the transportation safety bolts before operating the washing machine! Otherwise, the product will be damaged.

C Keep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved again in the future.

Install the transport safety bolts in reverse order of the disassembly procedure.

Never move the product without the transportation safety bolts properly fixed in place!

Washing Machine / User’s Manual

7 / EN

4.1.4 Connecting water supply

C Thewatersupplypressurerequiredtoruntheproductisbetween1to10bars(0.1–1MPa).Itisnecessarytohave 10–80litersofwaterflowingfromthefullyopentapinoneminutetohaveyourmachinerunsmoothly.Attacha pressure reducing valve if water pressure is higher.

A CAUTION: Models with a single water inlet should not be connected to the hot water tap. In such a case the laundry will get damaged or the product will switch to protection mode and will not operate.

CAUTION: Do not use old or used water inlet hoses on the new product. It may cause stains on your laundry.

1Tighten the nuts of the hose by hand. Never use a tool when tightening the nuts.

2When hose connection is completed, check whether there is leak problems at the connection points by opening the taps fully. If any leaks occur, turn off the tap and remove the nut.

Retighten the nut carefully after checking the seal. In order to prevent the water leaks and resultant damages, keep the taps closed when you do not use the product.

4.1.5Connecting the drain hose to the drain

•Attachtheendofthedrainhosedirectlytowastewaterdrain,lavatoryorbathtub.

A CAUTION: Your drain house will be flooded if the hose comes out of its housing during water discharge. Moreover, there is risk of scalding due to high washing temperatures! In order to prevent such situations and make sure that the machine performs water intake and discharge processes without any problem, fix the drain hose securely.

100 cm 40 cm

•Connectthedrainhosetoaminimumheightof40 cm and a maximum height of 100 cm.

•Incasethedrainhoseiselevatedafterlayingiton the floor level or close to the ground (less than 40 cm above the ground), water discharge becomes more difficult and the laundry may come out excessively wet. Therefore, follow the heights described in the figure.

•Topreventthewastewatertogobackintothemachineagainandtoensureeasydrainage,donot immerse the end of the hose into the waste water or do not insert it into the drain for more than 15 cm. If it is too long, cut it short.

•Theendofthehoseshouldnotbebent,itshouldnotbesteppedonandthehosemustnotbe pinched between the drain and the machine.

•Ifthelengthofthehoseistooshort,useitbyaddinganoriginalextensionhose.Lengthofthe hose may not be longer than 3.2 m. To avoid water leak failures, the connection between the extension hose and the drain hose of the product must be fitted well with an appropriate clamp as not to come off and leak.

8 / EN

Washing Machine / User’s Manual

4.1.6 Adjusting the feet

A CAUTION: In order to ensure that the product operates more silently and vibration-free, it must stand level and balanced on its feet. Balance the machine by adjusting the feet. Otherwise, the product may move from its place and cause crushing and vibration problems.

CAUTION: Do not use any tools to loosen the lock nuts. Otherwise, they will get damaged.

1 Loosenthelocknutsonthefeetbyhand.

2 Adjust the feet until the product stands in a stable and balanced way. 3. Tighten all lock nuts by hand again.

4.1.7 Electrical connection

Connect the product to a grounded outlet protected by a 16 A fuse. Our company shall not be liable for any damages that will arise when the product is used without grounding in accordance with the local regulations.

• Connectionmustcomplywithnationalregulations.

• Thewiringfortheelectricaloutletcircuitmustbesufficienttomeettheappliancerequirements.

Use of a Groud Fault Circuit Interrupter (GFCI) is recommended.

• Powercableplugmustbewithineasyreachafterinstallation.

• Ifthecurrentvalueofthefuseorbreakerinthehouseislessthan16Amps,haveaqualified

electrician install a 16 Amp fuse.

• Thevoltagespecifiedinthe"Technicalspecifications"sectionmustbeequaltoyourmains

voltage.

• Donotmakeconnectionsviaextensioncablesormulti-plugs.

B CAUTION: Damaged power cables must be replaced by the Authorised Service Agents.

4.1.8 Initial use

Before starting to use the product make sure that the preparations are made which are in line with the “Important Safety and Environment Instructions” and the instructions in the “Installation” section.

To prepare the product for washing laundry, perform first operation in Drum Cleaning programme. If this program is not available in your machine, apply the method which is described in the section 4.4.2.

C Use an anti-limescale suitable for the washing machines.

Some water might have remained in the product due to the quality control processes in the production. It is not harmful for the product.

Washing Machine / User’s Manual

9 / EN

4.2 Preparation

4.2.1 Sorting the laundry

* Sort laundry according to type of fabric, color, and degree of soiling and allowable water temperature.

* Always obey the instructions given on the garment tags.

4.2.2 Preparing laundry for washing

• Laundryitemswithmetalattachmentssuchas,underwiredbras,beltbucklesormetalbuttons will damage the machine. Remove the metal pieces or wash the clothes by putting them in a laundry bag or pillow case.

• Takeoutallsubstancesinthepocketssuchascoins,pensandpaperclips,andturnpocketsinside out and brush. Such objects may damage the product or cause noise problem.

• Putsmallsizeclothessuchasinfant'ssocksandnylonstockingsinalaundrybagorpillowcase.

• Placecurtainsinwithoutcompressingthem.Removecurtainattachmentitems.

• Fastenzippers,sewloosebuttonsandmendripsandtears.

• Wash“machinewashable”or“handwashable”labeledproductsonlywithanappropriate

programme.

• Donotwashcoloursandwhitestogether.New,darkcolouredcottonsreleasealotofdye.Wash

them separately.

• Toughstainsmustbetreatedproperlybeforewashing.Ifunsure,checkwithadrycleaner.

• Onlyusethedyes/colorchangersanddescalingagentswhichareappropriatetomachinewash.

Always follow the instructions on the package.

• Washtrousersanddelicatelaundryturnedinsideout.

• KeeplaundryitemsmadeofAngorawoolinthefreezerforafewhoursbeforewashing.Thiswill

reduce pilling.

• Laundrythataresubjectedtomaterialssuchasflour,limedust,milkpowder,etc.intenselymust be shaken off before placing into the machine. Such dusts and powders on the laundry may build up on the inner parts of the machine in time and can cause damage.

4.2.3 Things to be done for energy saving

Following information will help you use the product in an ecological and energy-efficient manner.

• Operatetheproductinthehighestcapacityallowedbytheprogrammeyouhaveselected,butdo not overload; see, "Programme and consumption table". See, “Programme and consumption table"

• Alwaysfollowtheinstructionsonthedetergentpackaging.

• Washslightlysoiledlaundryatlowtemperatures.

• Usefasterprogrammesforsmallquantitiesoflightlysoiledlaundry.

• Donotuseprewashandhightemperaturesforlaundrythatisnotheavilysoiledorstained.

• Ifyouplantodryyourlaundryinadryer,selectthehighestspinspeedrecommendedduring

washing process.

• Donotusemoredetergentthantherecommendedamountspecifiedonitspackage.

4.2.4Loading the laundry

1.Open the laundry cover.

2.Put the laundry items into the machine in a loose manner.

3.Push and close the loading cover until you hear the locking sound. Ensure that no items are caught in the door. The loading door is locked while a programme is running. The door can only be opened a while after the programme comes to an end.

4.2.5 Correct load capacity

The maximum load capacity depends on the type of laundry, the degree of soiling and the washing programme desired.

Machine automatically adjusts the water amount according to the weight of the laundry put inside it.

A WARNING: Follow the information in the “Programme and consumption table”. When overloaded, machine's washing performance will drop. Moreover, noise and vibration problems may occur.

10 / EN

Washing Machine / User’s Manual

4.2.6 Using detergent and softener

C When using detergent, softener, starch, fabric dye, bleacher and decolorant, descaling agents; read the manufacturer's instructions written on the package and follow the dosages specified. Use measuring cup if available.

2 3 1

The detergent drawer is composed of three compartments:

–(1)forprewash

–(2)formainwash

–(3)forsoftener

–() in addition, there is a siphon piece in the softener compartment.

	Detergent, softener and other cleaning agents
	• Adddetergentandsoftenerbeforestartingthewashingprogramme.
	•	Whilethewashingcycleisinprogress,donotleavethedetergentdispenseropen!
	• Whenusingaprogrammewithoutprewash,donotputanydetergentintotheprewash
		compartment (compartment nr. "1").
	• Inaprogrammewithprewash,donotputliquiddetergentintotheprewashcompartment
		(compartment nr. "1").
	• Donotselectaprogrammewithprewashifyouareusingadetergentbagordispensingball.Place
		the detergent bag or the dispensing ball directly among the laundry in the machine.
	If you are using liquid detergent, do not forget to place the liquid detergent container into the main
		wash compartment (compartment number “2”).
	Choosing the detergent type
	Detergent type to be used depends on the fabric type and color.
	• Usedifferentdetergentsforcolouredandwhitelaundry.
	• Washyourdelicateclothesonlywithspecialdetergents(liquiddetergent,woolshampoo,etc.)
	•	used solely for delicate clothes.
		Whenwashingdarkcolouredclothesandquilts,itisrecommendedtouseliquiddetergent.
	•	Washwoolenswithspecialdetergentmadespecificallyforwoolens.
	A		CAUTION: Use only detergents manufactured specifically for washing machines.
			CAUTION: Do not use soap powder.

Adjusting detergent amount

The amount of washing detergent to be used depends on the amount of laundry, the degree of soiling and water hardness.

• Donotuseamountsexceedingthedosagequantitiesrecommendedonthedetergentpackage to avoid problems of excessive foam, poor rinsing, financial savings and finally, environmental protection.

• Uselesserdetergentforsmallamountsorlightlysoiledclothes.

Using softeners

Pour the softener into the softener compartment of the detergent drawer.

• Donotexceedthe(>max<)levelsignonthesoftenercompartment.

• Ifthesoftenerhaslostitsfluidity,diluteitwithwaterbeforeputtingitinthedetergentdrawer.

Washing Machine / User’s Manual

11 / EN

Using liquid detergents

If the product contains a liquid detergent cup:

2		•	Puttheliquiddetergentcontainerintothe
			compartment no “2”.
		•	Iftheliquiddetergentlostitsfluidity,dilute
			it with water before putting it into the
			detergent container.

If the product does not contain a liquid detergent cup:

• Donotuseliquiddetergentfortheprewashinaprogrammewithprewash.

• LiquiddetergentstainsyourclotheswhenusedwithDelayedStartfunction.Ifyouaregoingto use the Delayed Start function, do not use liquid detergent.

Using gel and tablet detergent

• Ifthegeldetergentthicknessisfluidalandyourmachinedoesnotcontainaspecialliquid detergent cup, put the gel detergent into the main wash detergent compartment during first water intake. If your machine contains a liquid detergent cup, fill the detergent into this cup before starting the programme.

• Ifthegeldetergentthicknessisnotfluidalorintheshapeofcapsuleliquidtablet,putitdirectly

into the drum before washing.

• Puttabletdetergentsintothemainwashcompartment(compartmentnr."2")ordirectlyintothe

drum before washing.

Using starch

• Puttheliquidsoda,powdersodaorthefabricdyeintothesoftenercompartment.

Do not use softener and starch together in a washing cycle.

Wipe the inside of the machine with a damp and clean cloth after using starch.

Using limescale remover

• Whenrequired,uselimescaleremoversmanufacturedspecificallyforwashingmachinesonly.

Using bleaches

Add the bleach at the beginning of the washing cycle by selecting a prewash program. Do not put detergent in the prewash compartment. As an alternative application, select a programme with extra rinse and add the bleaching agent while the machine is taking water from the detergent compartment during first rinsing step.

• Donotusebleachingagentanddetergentbymixingthem.

• Usejustalittleamount(approx.50ml)ofbleachingagentandrinsetheclothesverywellasit causes skin irritation. Do not pour the bleach onto the laundry and do not use it with the colored items.

• Whenusingoxygen-baseddecolorant,selectaprogramwhichwashesthelaundryatalow

temperature.

• Oxygen-baseddecolorantcanbeusedwiththedetergent;however,ifitisnotatthesame consistence, first put detergent in the compartment number “2” in the detergent dispenser and wait for the machine to flush the detergent when taking in water. While the machine continues taking in water, add decolorant in the same compartment.

12 / EN

Washing Machine / User’s Manual

4.2.7 Tips for efficient washing

Soiling Level

							Clothes
		Light Colours and						Black/Dark	Delicates/
						Colours			Woolens/
				Whites				Colours
									Silks
		(Recommended temperature			(Recommended temperature			(Recommended	(Recommended
		range based on soiling level:			range based on soiling level:			temperature range	temperature range
		40-90	o	C)	cold -40	o	C)	based on soiling level:	based on soiling
								cold -40 oC)	level: cold -30 oC)
		It may be necessary to pre-			Powder and liquid
		treat the stains or perform							Prefer liquid
	Heavily				detergents recommended
		prewash. Powder and liquid						Liquiddetergents	detergents
	Soiled	detergents recommended			for colors can be used at				produced for
					dosages recommended for			suitable for colors
		for whites can be used at			heavily soiled clothes. It is			and dark colors can	delicate clothes.
	(difficult stains	dosages recommended for							Woolen and silk
					recommended to use powder			be used at dosages
	such as grass,	heavily soiled clothes. It is			detergents to clean clay and			recommended for	clothes must
	coffee, fruits	recommended to use powder			soil stains and the stains that			heavily soiled clothes.	be washed with
	and blood.)	detergents to clean clay and			are sensitive to bleaches. Use				special woolen
		soil stains and the stains that			detergents without bleach.				detergents.
		are sensitive to bleaches.
	Normally				Powder and liquid detergents			Liquiddetergents	Prefer liquid
		Powder and liquid detergents							detergents
	Soiled				recommended for colors			suitable for colors	produced for
	(For example,	recommended for whites			can be used at dosages			and dark colors can	delicate clothes.
	stains caused	can be used at dosages			recommended for normally			be used at dosages	Woolen and silk
	by body on	recommended for normally			soiled clothes. Detergents			recommended for	clothes must
	collars and	soiled clothes.			which do not contain bleach			normally soiled	be washed with
	cuffs)				should be used.			clothes.	special woolen
									detergents.
					Powder and liquid detergents				Prefer liquid
	Lightly	Powder and liquid detergents						Liquiddetergents	detergents
					recommended for colors				produced for
	Soiled	recommended for whites			can be used at dosages			suitable for colors	delicate clothes.
								and dark colors can
		can be used at dosages			recommended for lightly			be used at dosages	Woolen and silk
	(No visible	recommended for lightly soiled			soiled clothes. Detergents				clothes must
								recommended for
	stains exist.)	clothes.			which do not contain bleach			lightly soiled clothes.	be washed with
					should be used.				special woolen
									detergents.

Washing Machine / User’s Manual

13 / EN

4.3 Operating the product

4.3.1 Control panel

Daily Xpress 30º

Hemden 40º

Chemises 40º

Handwas/Wol 40º

Lavage à la main/Laine 40º

Synthetisch 40º

Synthétique 40º

Synthetisch 20º

Synthétique 20º

Donsjas 40º

Doudoune 40º

Reiniging trommel

Nettoyagetambour

1

Centrifugeren + Pompen

Essorage + Vidange

Katoen 20º

Coton 20º

Katoen 40º

Coton 40º

Katoen Eco

Coton Eco 40º

Katoen Eco

Coton Eco

Katoen60ºmetVoorwas

Coton60ºavecPrélavage

Katoen 90º

Coton 90º

Spoelen

Rinçage

2	3	4	5	6
1400
1200
800		9
600		6
		3

Spoelen	Uitgestelde	Start/
Rinçage	start	Pauze
	Départ	Départ/
		Pause

WTV 7711 BW0

Einde-Fin

Reset-Annulation

Centrifugeren-Essorage

Spoelen-Rinçage

Wassen-Lavage

Uitgestelde start-

	9	8	7
1 - Programme Selection knob (Uppermost			5-DelayedStartIndicatorLEDs
position On / Off)			6-ProgrammeFollow-upLEDs
2	-SpinSpeedIndicatorLEDs		7 - Start / Pause Button
3	-ChildLockEnabledLED		8 - Delayed Start Setting Button
4-DoorLockEnabledLED			9 - Spin Speed Adjustment button

4.3.2 Preparing the machine

1.Make sure that the hoses are connected tightly. 2.Plug in your machine.

3.Turn the tap on completely. 4.Place the laundry in the machine. 5.Add detergent and fabric softener.

4.3.3 Programme selection and tips for efficient washing

1.Select the programme suitable for the type, quantity and soiling degree of the laundry in accordance with the "Programme and consumption table" and the temperature table below.

2.Select the desired programme with the Programme Selection knob.

14 / EN

Washing Machine / User’s Manual

4.3.4 Programme and consumption table

EN		2
Programme			(kg)LoadMax.	DurationProgramme(~min)	ConsumptionWater(l)	ConsumptionEnergy(kWh)	Speed***Max.
	90		7	195	98,5	2,41	1400
Katoen	40		7	195	94,3	1,06	1400
	20		7	195	93,4	0,64	1400
Katoen 60º met Voorwas	60		7	215	105,5	2,15	1400
	60**		7	225	51,4	0,888	1400
Katoen Eco	60**		3,5	195	42	0,680	1400
	40**		3,5	170	42	0,680	1400
Synthetisch	40		3	130	70	0,80	1200
	20		3	130	68	0,30	1200
Daily Xpress	30		7	28	70	0,15	1400
Handwas / Wol	40		1,5	65	63	0,47	1200
Donsjas	40		1,5	105	90	0,85	1000
Hemden	40		3	80	45	0,62	800
Reiniging trommel	90		-	160	70	2,25	600

** : EnergyLabelprogramme(EN 60456 Ed.3)

***: If maximum spin speed of the machine is lower then this value, you can only select up to the maximum spin speed. - : See the programme description for maximum load.

** "Cotton Economic 40°C and Cotton Economic 60°C are standard programmes." These programmes are known as '40°C cotton standard programme' and '60°C cotton standard programme' and indicated with the symbols on the panel.

C Water and power consumption may vary subject to the changes in water pressure, water hardness and temperature, ambient temperature, type and amount of laundry, spin speed, and changes in electric voltage.

Depending on the amount of laundry you have loaded into your machine, there may be a difference of 1-1.5 hours between the duration shown in the Programme and consumption table and the actual washing duration. Duration will be automatically updated soon after the washing starts.

Washing Machine / User’s Manual

15 / EN

IndicativevaluesforSyntheticsprogrammes(EN)

	Load(kg)	Water Consumption (l)	Energy Consumption (kWh)	Programme Duration (min)
Synthetics 40	3	70	0,80	115/140
Synthetics 20	3	68	0.30	115/140

Remaining Moisture	Remaining Moisture
Content (%) **	Content (%) **

≤ 1000 rpm	>1000rpm
45	40
45	40

** Remaining moisture content values may differ according to the selected spin speed.

4.3.5 Main programmes

Depending on the type of fabric, use the following main programmes.

•Katoen(Cottons)

Use this programme for your cotton laundry (sheets, bedlinen, towels, bathrobes, underwear etc.). Your laundry will be washed with vigorous washing action for a longer washing cycle.

•Synthetisch(Synthetics)

Use to wash your synthetic clothes (shirts, blouses, synthetic/cotton blends, etc.). Your laundry will be washed with a gentle action for a shorter washing cycle when compared to the Cottons programme. For curtains and tulle, it is recommended to use Synthetics 20˚C or 40˚C programme.

• Handwas/Wol (Hand Wash / Woollens)

Use to wash your woolen/delicate laundry. Your laundry will be washed with a very gentle washing action in order not to damage the clothes.

"Woolens programme of this machine is approved by The Woolmark Company for washing machine-washable woolen products provided that the products are washed in accordance with the instructions on the product tag and the instructions published by the manufacturer of this machine. M1367"

In UK, Ireland, Hong Kong and India, the Woolmark trademark is a Certification trademark.

4.3.6 Additional programmes

For special cases, additional programmes are available in the machine.

C Additional programmes may differ according to the model of the machine.

•KatoenEco(CottonsEco)

Use this programme to wash your laundry washable in cottons programme for a longer time, still with a very good performance for saving purposes.

C Cotton Eco programme consumes less energy compared to other cotton programmes.

•Katoen60ºmetVoorwas(Cottons60°withPrewash)

Use this programme only for heavily soiled cotton clothes. Add detergent into the prewash compartment.

• Daily Xpress

Use this programme to wash your lightly soiled cotton clothes in a short time.

16 / EN

Washing Machine / User’s Manual

•Hemden(Shirts)

This programme is used to wash the shirts made from cotton, synthetic and synthetic blended fabrics altogether. It reduces wrinkles. Pre-treatment algorithm is executed.

•Applythepre-treatmentchemicalonyourgarmentsdirectlyoraddittogetherwithdetergent when the machine starts to take water from the main washing compartment. Thus the machine will wash them in a short period of time and expected lifespan of your shirts will extend.

•Donsjas(DownWear)

Use this programme to wash your coats, vest, jackets etc. containing feathers with a "machinewashable" label on them. Thanks to special spinning profiles, it is ensured that the water reaches the air gaps amongst the feathers.

•Reinigingtrommel(DrumClean)

Use regularly (once in every 1-2 months) to clean the drum and provide the required hygiene. Operate the programme while the machine is completely empty. To obtain better results, put powder lime-scale remover for washing machines into the detergent compartment no. “2”. When the programme is over, leave the loading door ajar so that the inside of the machine gets dry.

C This is not a washing programme. It is a maintenance programme.

Do not run the programme when there is something in the machine. If you try to do so, the machine detects that there is load inside and aborts the programme.

4.3.7 Special programmes

For specific applications, select any of the following programmes.

•Spoelen(Rinse)

Use when you want to rinse or starch separately.

•Centrifugeren+Pompen(Spin+Drain)

You can use this function to remove the water on the garment of drain the water in the machine. Before selecting this programme, select the desired spin speed and press Start / Pause button. First, the machine will drain the water inside of it. Then, it will spin the laundry with the set spin speed and drain the water coming out of them.

If you wish to drain only the water without spinning your laundry, select the Pump+Spin programme and then select the No Spin function with the help of Spin Speed Adjustment button. Press Start / Pause button.

C Use a lower spin speed for delicate laundries.

4.3.8 Speed selection

Whenever a new programme is selected, the recommended spin speed of the selected programme is displayed on the spin speed indicator.

To decrease the spin speed, press the Spin Speed Adjustment button. Spin speed decreases gradually. Then, depending on the model of the product, "Rinse Hold" and "No Spin" options appear on the display. When "No Spin" is selected, the rinse level indicator lights will not turn on.

Rinse hold

If you are not going to unload your clothes immediately after the programme completes, you can use rinse hold function to keep your laundry in the final rinsing water in order to prevent them from getting wrinkled when there is no water in the machine. Press Start / Pause button after this process if you want to drain the water without spinning your laundry. Programme will resume and complete after draining the water.

If you want to spin the laundry held in water, adjust the Spin Speed and press Start / Pause button. The programme will resume. Water is drained, laundry is spun and the programme is completed.

C If the programme has not reached the spinning step, you can change the speed without switching the machine to Pause mode.

Washing Machine / User’s Manual

17 / EN

4.3.9 Delayed Start

With the Delayed Start function the startup of the programme may be delayed up to 3, 6 or 9 hours.

C Do not use liquid detergents when you set Delayed Start! There is the risk of staining of the clothes.

1.Open the loading door, place the laundry and put detergent, etc.

2.Select a washing programme and spin speed.

3.Set the desired time by pressing the Delayed Start button. When the button is pressed once, 3 hours delayed start is selected. When the same button is pressed again, 6 hours delay is selected, and when it is pressed for the third time, 9 hours delayed start is selected. If you press the Delayed Start button once again, Delayed Start function will be canceled.

4.Press Start / Pause button. Previous delayed start time light turns off and next delayed start time light turns on after every 3 hours.

5.At the end of the countdown, all delayed start lights will turn off and the selected programme will start.

C You can switch the machine to pause mode and add laundry during the delayed start period.

Changing the delayed start period

If you want to change the time during countdown, you will need to cancel the programme and set the delay time again.

Canceling the Delayed Start function

If you want to cancel the delayed start countdown and start the programme immediately:

1. Turn the Programme Selection knob to any programme. Thus, Delayed Start function will be canceled. The End/Cancel light flashes continuously.

2. Then, select the programme you want to run again. 3. Press Start / Pause button to start the programme.

4.3.10Startingtheprogramme

1. Press Start / Pause button to start the programme.

2. Programme follow-up light showing the startup of the programme will turn on.

4.3.11 Child Lock

UseChildLockfunctiontopreventchildrenfromtamperingwiththemachine.Thusyoucanavoid any changes in a running programme.

C IftheProgrammeSelectionknobisrotatedwhenthechildlockisactive,"ChildLockEnabledLED"willflash3 times.TheChildLockdoesnotallowanychangeintheprogrammesortheselectedspeed.

EvenifanotherprogrammeisselectedwiththeProgrammeSelectionknobwhiletheChildLockisactive, previously selected programme will continue running.

WhentheChildLockisactiveandthemachineisrunning,youcanswitchthemachinetoPausemodewithout deactivatingtheChildLockbyturningtheProgrammeSelectionknobtoOn/Offposition.Whenyouturnthe

Programme Selection knob afterwards, the programme will resume.

To activate the Child Lock:

Press and hold Speed and Delayed Start buttons for 3 seconds. While you are holding for 3 seconds, the"ChildLockEnabledLED"willflash.YoucanreleasethebuttonswhentheLEDsbecome permanently on.

To deactivate the Child Lock:

Press and hold Speed and Delayed Start buttons for 3 seconds while any programme is running.

Whileyouareholdingfor3seconds,the"ChildLockEnabledLED"willflash.Youcanreleasethe buttonswhentheLEDturnsoffcompletely.

C Inadditiontothemethodabove,todeactivatetheChildLock,switchtheProgrammeSelectionknobtoOn/Off position when no programme is running, and select another programme.

ChildLockisnotdeactivatedafterpowerfailuresorwhenthemachineisunplugged.

18 / EN

Washing Machine / User’s Manual

4.3.12 Progress of programme

Progress of a running programme can be followed from the Programme Follow-up indicator. At the beginning of every programme step, the relevant indicator light will turn on and light of the completed step will turn off.

You can change the speed settings without stopping the programme flow while the programme is running. To do this, the change you are going to make must be in a step after the running programme step. If the change is not compatible, relevant lights will flash for 3 times.

C If the machine does not proceed to the spinning step, the Rinse Hold function might be active or the automatic unbalanced load detection system might be activated due to the unbalanced distribution of the laundry in the machine.

4.3.13 Loading door lock

There is a locking system on the loading door of the machine that prevents opening of the loading door in cases when the water level is unsuitable.

LoadingdoorlightwillstartflashingwhenthemachineisswitchedtoPausemode.Themachine checksthelevelofthewaterinside.Ifthelevelissuitable,theLoadingDoorlightturnsoffandthe loading door can be opened within 1-2 minutes.

Ifthelevelisunsuitable,theLoadingDoorlightremainsonandtheloadingdoorcannotbeopened. IfyouareobligedtoopentheLoadingDoorwhiletheLoadingDoorlightison,youmustcancelthe current programme. See. "Cancelling the programme"

4.3.14 Changing the selections after programme has started

Switching the machine to pause mode

Press the Start / Pause button to switch the machine to pause mode while a programme is running. The light of the step which the machine is in starts flashing in the Programme Follow-up indicator to show that the machine has been switched to the pause mode.

Additionally,whentheloadingdoorisopenable,theLoadingDoorlightturnsoffcompletely.

Changing the speed settings

You can change the speed settings of the programme that is currently running. See "Speed selection".

C If no change is allowed, the relevant light will flash 3 times.

Adding or taking out laundry

You can load/unload laundry when a programme is running if the water level is appropriate to open the door. To do this:

1. Press Start / Pause button to switch the machine to pause mode. The programme follow-up light of the relevant step during which the machine was switched into the pause mode will flash.

2. WaituntiltheLoadingDoorcanbeopened.

3.OpentheLoadingDoorandaddortakeoutthelaundry. 4.ClosetheLoadingDoor.

5. Make changes in speed settings, if necessary. 6. Press Start / Pause button to start the machine.

Washing Machine / User’s Manual

19 / EN

4.3.15 Cancelling the programme

To cancel the programme, turn the Programme Selection knob to select another programme. Previous programme will be cancelled. End / Cancel light will flash continuously to notify that the programme has been canceled.

Your machine will end the programme when you turn the Programme Selection knob; however, it does not drain the water inside. When you select and start a new programme, the newly selected programme will start depending on the step the previous programme was canceled in. For example, it may take in additional water or continue to wash with the water inside.

C Some programmes may start by discharging the water inside the machine. Depending on the step where the programme was canceled in, you may have to put detergent and softener again for the programme you have selected anew.

4.3.16 End of programme

Whentheprogrammeends,"End"LEDbecomesonattheProgrammeFollow-upindicator.

1. Waituntilthe"DoorLockEnabledLED"goesoffcompletely.

2. To switch off the machine, turn the Programme Selection Knob to On/Off position.

3. Take out your laundry and close the loading door. Your machine is ready for the next washing cycle.

4.3.17 Your machine features "Pause Mode".

After you switch on your machine with the programme selection button (by switching the button to a different position than the On/Off position), if no programme is started or no other procedure is performed in the selection step or no action is taken within approx. 2 minutes after the selected programme ends, your machine will switch to energy saving mode automatically. The brightness of the indicator lights will decrease. Also, if your product has a display that shows programme time, this display will be completely turned off. If you turn the Programme Selection knob or touch any button,

lights and display will switch back to previous condition. The selections which you make when exiting from the energy efficiency may change. Please check the correctness of your selections before starting the programme. If necessary, please make your settings again. This is not an error.

20 / EN

Washing Machine / User’s Manual

Repeat Drum Cleaning process in every 2 months.

Use an detergent / anti-limescale suitable for the washing machines.

4.4 Maintenance and cleaning

Service life of product extends and frequently experienced problems will be reduced if it is cleaned at regular intervals.

4.4.1 Cleaning the detergent drawer

Clean the detergent drawer at regular intervals (every 4-5 washing cycles)

as shown below in order to prevent accumulation of powder detergent in

time.

Lifttherearpartofthesiphontoremoveitasillustrated.

If more than normal amount of water and softener mixture starts to gather in the softener compartment, the siphon must be cleaned.

1 Press the dotted point on the siphon in the softener compartment and pull towards you until the compartment is removed from the machine.

2. Wash the detergent drawer and the siphon with plenty of lukewarm water in a washbasin. In order to prevent the residues to contact your skin, clean it with an appropriate brush by wearing a pair of gloves.

3 Insert the drawer back into its place after cleaning and make sure that it is seated well.

4.4.2 Cleaning the loading door and the drum

For products with drum cleaning programme, please see Operating the product - Programmes.

C

After every washing make sure that no foreign substance is left in the drum. If the holes on the bellow shown in the figure is blocked, open the holes using a toothpick.

Foreign metal substances will cause rust stains in the drum. Clean the stains on the drum surface by using cleaning agents for stainless steel.

Never use steel wool or wire wool. These will damage the painted, chromated and plastic surfaces.

4.4.3 Cleaning the body and control panel

Wipe the body of the machine with soapy water or non-corrosive mild gel detergents as necessary, and dry with a soft cloth.

Use only a soft and damp cloth to clean the control panel.

4.4.4 Cleaning the water intake filters

There is a filter at the end of each water intake valve at the rear of the machine and also at the end of each water intake hose where they are connected to the tap. These filters prevent foreign

substances and dirt in the water to enter the washing machine. Filters should be cleaned as they do get dirty.

1.	Close the taps.
2.	Remove the nuts of the water intake hoses to access
	the filters on the water intake valves. Clean them
	with an appropriate brush. If the filters	are too dirty,
	remove them from their places with a pliers and clean
3.	in this way.
	Take out the filters on the flat ends of the water
	intake hoses together with the gaskets	and clean
4.	thoroughly under running water.
	Replace the seals and filters carefully and tighten
	their nuts by hand.

Washing Machine / User’s Manual

21 / EN

4.4.5 Draining remaining water and cleaning the pump filter

The filter system in your machine prevents solid items such as buttons, coins and fabric fibers clogging the pump impeller during discharge of washing water. Thus, the water will be discharged without any problem and the service life of the pump will extend.

If the machine fails to drain water, the pump filter is clogged. Filter must be cleaned whenever it is clogged or in every 3 months. Water must be drained off first to clean the pump filter.

In addition, prior to transporting the machine (e.g., when moving to another house) and in case of freezingofthewater,watermayhavetobedrainedcompletely.

A CAUTION: Foreign substances left in the pump filter may damage your machine or may cause noise problem.

CAUTION: If the product is not being used, shut the tap shut, remove mains pipe and drain the water inside themachineagainstanylikelyfreezing.

CAUTION: After each use, turn off the water tap to which the mains hose is connected.

In order to clean the dirty filter and discharge the water:

1 Unplug the machine to cut off the supply power.

A CAUTION: Temperatureofthewaterinsidethemachinemayriseupto90ºC.Toavoidtheburningrisk,clean the filter after the water inside the machine is cooled down.

2. Open the filter cover.

3 Follow the below procedures in order to drain water.

The product has an emergency water draining hose, in order to drain the water:

a Pull the emergency draining hose out from its seat

b Place a large container at the end of the hose. Drain the water into the container by pulling out the plug at the end of the hose. When the container is full, block the inlet of the hose by replacing the plug. After the container is emptied, repeat the above procedure to drain the water in the machine completely.

c When draining of water is finished, close the end by the plug again and fix the hose in its place.

d Turn and remove the pump filter.

4.Clean any residues inside the filter as well as fibers, if any, around the pump impeller region.

5.Replace the filter.

6.If the filter cap is composed of two pieces, close the filter cap by pressing on the tab. If it is one piece, seat the tabs in the lower part into their places first, and then press the upper part to close.

22 / EN

Washing Machine / User’s Manual

5	Troubleshooting
	Problem	Reason	Solution
Program does not start after		Start / Pause / Cancel button was not pressed.	• *Press the Start / Pause / Cancel button.
closing the door.
		It may be difficult to close the loading door in case	• Reduce the amount of laundry and make sure
		of excessive loading.	that the loading door is closed properly.
Programme cannot be started or		Washing machine has switched to self protection	• To cancel the programme, turn the
selected.		mode due to a supply problem (line voltage, water	Programme Selection knob to select another
		pressure, etc.).	programme. Previous programme will be
			canceled. (see. “Cancellation of program”)
Water in the machine.		Some water might have remained in the product due	• This is not a failure; water is not harmful to
		to the quality control processes in the production.	the machine.
The machine enters standby		Tap is turned off.	• Turn on the taps.
mode after the programme		Water inlet hose is bent.	• Flatten the hose.
starts or it does not take in		Water inlet filter is clogged.	• Clean the filter.
water.		Loading door may be open.	• Close the door.
		The water connection may be wrong or water may	• Check the water connection. If the water is
		be cut off (When the water is cut off, washing or	cut off, press the Start/Pause key after the
		rinsing LEDs flash).	water has been supplied again to resume the
			operation from standby mode.
Machine does not drain water.		Water drain hose might be clogged or twisted.	• Clean or flatten the hose.
		Pump filter is clogged.	• Clean the pump filter.
Machine vibrates or makes noise.		Machine might be standing unbalanced.	• Adjust the feet to level the machine.
		A hard substance might have entered into the	• Clean the pump filter.
		pump filter.
		Transportation safety bolts are not removed.	• Remove the transportation safety bolts.
		Laundry quantity in the machine might be too little.	• Add more laundry to the machine.
		Machine might be overloaded with laundry.	• Take out some of the laundry from the
			machine or distribute the load by hand to
			balance it homogenously in the machine.
		Machine might be leaning on a rigid item.	• Make sure that the machine is not leaning
			on anything.
There is water leaking from the		Water drain hose might be clogged or twisted.	• Clean or flatten the hose.
bottom of the washing machine.
		Pump filter is clogged.	• Clean the pump filter.
Machine stopped shortly after		Machine might have stopped temporarily due to	• It will resume running when the voltage
the programme started.		low voltage.	restores to the normal level.
Machine directly discharges the		Draining hose might not be at adequate height.	• Connect the water draining hose as
water it takes in.			described in the operation manual.
No water can be seen in the		The water level is not visible from outside of the	• This is not a failure.
machine during washing.		washing machine.
Loading door cannot be opened.		Door lock is activated because of the water level	• Drain the water by running the Pump or Spin
		in the machine.	programme.
		Machine is heating up the water or it is at the	• Wait until the programme completes.
		spinning cycle.
		Child lock is engaged. Door lock will be deactivated	• Wait for a couple of minutes for deactivation
		a couple of minutes after the programme has	of the door lock.
		come to an end.
		Loading door may be stuck because of the	• Grab the handle and push and pull the loading
		pressure it is subjected to.	door to release and open it.
Washing takes longer time than		Water pressure is low.	• Machine waits until taking in adequate
specified in the manual.(*)			amount of water to prevent poor washing
			quality due to the decreased amount of
			water. Therefore, the washing time extends.
		Voltage might be low.	• Washing time is prolonged to avoid poor
			washing results when the supply voltage is low.
		Input temperature of water might be low.	• Required time to heat up the water extends
			in cold seasons. Also, washing time can be
			lengthened to avoid poor washing results.
		Number of rinses and/or amount of rinse water	• Machine increases the amount of rinse water
		might have increased.	when good rinsing is needed and adds an
			extra rinsing step if necessary.
		Excessive foam might have occurred and	• Use recommended amount of detergent.
		automatic foam absorption system might have
		been activated due to too much detergent usage.

Washing Machine / User’s Manual

23 / EN

Problem	Reason	Solution
Programme time does not	Timer may stop during water intake.	• Timer indicator will not countdown until the
countdown. (On models with		machine takes in adequate amount of water.
display) (*)		The machine will wait until there is sufficient
		amount of water to avoid poor washing
		results due to lack of water. Timer indicator
		will resume countdown after this.
	Timer may stop during heating step.	• Timer indicator will not countdown until the
		machine reaches the selected temperature.
	Timer may stop during spinning step.	• Automatic unbalanced load detection system
		might be activated due to the unbalanced
		distribution of the laundry in the drum.
Programme time does not	There might be unbalanced load in the machine.	• Automatic unbalanced load detection system
countdown. (*)		might be activated due to the unbalanced
		distribution of the laundry in the drum.
Machine does not switch to	There might be unbalanced load in the machine.	• Automatic unbalanced load detection system
spinning step. (*)		might be activated due to the unbalanced
		distribution of the laundry in the drum.
	The machine will not spin if water is not drained	• Check the filter and the draining hose.
	completely.
	Excessive foam might have occurred and	• Use recommended amount of detergent.
	automatic foam absorption system might have
	been activated due to too much detergent usage.
Washing performance is poor:	Insufficient amount of detergent has been used	• Use the recommended amount of detergent
Laundry turns gray. (**)	over a long period of time.	appropriate for water hardness and the laundry.
	Washing was made at low temperatures for a	• Select the proper temperature for the
	long time.	laundry to be washed.
	Insufficient amount of detergent is used with	• Using insufficient amount of detergent with
	hard water.	hard water causes the soil to stick on the cloth
		and this turns the cloth into gray in time. It is
		difficult to eliminate graying once it happens.
		Use the recommended amount of detergent
		appropriate for water hardness and the laundry.
	Too much detergent is used.	• Use the recommended amount of detergent
		appropriate for water hardness and the laundry.
Washing performance is poor:	Insufficient amount of detergent is used.	• Use the recommended amount of detergent
Stains persist or the laundry is		appropriate for water hardness and the laundry.
not whitened. (**)	Excessive laundry was loaded in.	• Donotloadthemachineinexcess.Loadwith
		amounts recommended in the "Programme
		and consumption table".
	Wrong programme and temperature were	• Select the proper programme and
	selected.	temperature for the laundry to be washed.
	Wrong type of detergent is used.	• Use original detergent appropriate for the
		machine.
	Too much detergent is used.	• Put the detergent in the correct
		compartment. Do not mix the bleaching
		agent and the detergent with each other.
Washing performance is poor: Oily	Regular drum cleaning is not applied.	• Clean the drum regularly. For this, please
stains appeared on the laundry. (**)		see 4.4.2.
Washing performance is poor:	Odours and bacteria layers are formed on the	• Leavethedetergentdraweraswellasthe
Clothes smell unpleasantly. (**)	drum as a result of continuous washing at lower	loading door of the machine ajar after each
	temperatures and/or in short programmes.	washing. Thus, a humid environment favorable
		for bacteria cannot occur in the machine.
Colour of the clothes faded. (**)	Excessive laundry was loaded in.	• Do not load the machine in excess.
	Detergent in use is damp.	• Keep detergents closed in an environment
		free of humidity and do not expose them to
		excessive temperatures.
	A higher temperature is selected.	• Select the proper programme and
		temperature according to the type and
		soiling degree of the laundry.

24 / EN

Washing Machine / User’s Manual

Problem	Reason	Solution
It does not rinse well.	The amount, brand and storage conditions of the	• Use a detergent appropriate for the washing
	detergent used are inappropriate.	machine and your laundry. Keep detergents
		closed in an environment free of humidity and
		do not expose them to excessive temperatures.
	Detergent is put in the wrong compartment.	• If detergent is put in the prewash
		compartment although prewash cycle is not
		selected, machine can take this detergent
		during rinsing or softener step. Put the
		detergent in the correct compartment.
	Pump filter is clogged.	• Check the filter.
	Drain hose is folded.	• Check the drain hose.
Laundry became stiff after	Insufficient amount of detergent is used.	• Using insufficient amount of detergent for
washing. (**)		the water hardness can cause the laundry to
		become stiff in time. Use appropriate amount
		of detergent according to the water hardness.
	Detergent is put in the wrong compartment.	• If detergent is put in the prewash
		compartment although prewash cycle is not
		selected, machine can take this detergent
		during rinsing or softener step. Put the
		detergent in the correct compartment.
	Detergent might be mixed with the softener.	• Do not mix the softener with detergent.
		Wash and clean the dispenser with hot water.
Laundry does not smell like the	Detergent is put in the wrong compartment.	• If detergent is put in the prewash
softener. (**)		compartment although prewash cycle is not
		selected, machine can take this detergent
		during rinsing or softener step. Wash and
		clean the dispenser with hot water. Put the
		detergent in the correct compartment.
	Detergent might be mixed with the softener.	• Do not mix the softener with detergent.
		Wash and clean the dispenser with hot water.
Detergent residue in the	Detergent is put in wet drawer.	• Dry the detergent drawer before putting in
detergent drawer. (**)		detergent.
	Detergent has gotten damp.	• Keep detergents closed in an environment
		free of humidity and do not expose them to
		excessive temperatures.
	Water pressure is low.	• Check the water pressure.
	The detergent in the main wash compartment got	• Check the holes and clean if they are clogged.
	wet while taking in the prewash water. Holes of
	the detergent compartment are blocked.
	There is a problem with the detergent drawer valves.	• Call the Authorised Service Agent.
	Detergent might be mixed with the softener.	• Do not mix the softener with detergent.
		Wash and clean the dispenser with hot water.
	Regular drum cleaning is not applied.	• Clean the drum regularly. For this, please
		see 4.4.2.
Too much foam forms in the	Improper detergents for the washing machine are	• Use detergents appropriate for the washing
machine. (**)	being used.	machine.
	Excessive amount of detergent is used.	• Use only sufficient amount of detergent.
	Detergent was stored under improper conditions.	• Store detergent in a closed and dry location.
		Do not store in excessively hot places.
	Some meshed laundry such as tulle may foam too	• Use smaller amounts of detergent for this
	much because of their texture.	type of item.
	Detergent is put in the wrong compartment.	• Put the detergent in the correct
		compartment.
	Softener is being taken early.	• There may be problem in the valves or in the
		detergent dispenser. Call the Authorised
		Service Agent.
Foam is overflowing from the	Too much detergent is used.	• Mix 1 tablespoonful softener and ½ l water
detergent drawer.		and pour into the main wash compartment of
		the detergent drawer.
		• Put detergent into the machine suitable
		for the programmes and maximum
		loads indicated in the “Programme and
		consumption table”. When you use additional
		chemicals (stain removers, bleachs and etc),
		reduce the amount of detergent.

Washing Machine / User’s Manual

25 / EN

CAUTION: If you cannot eliminate the problem although you follow the instructions in this section, consult your dealer or the Authorised Service Agent. Never try to repair a nonfunctional product yourself.

Problem	Reason	Solution
Laundry remains wet at the end	Excessive foam might have occurred and	• Use recommended amount of detergent.
of the programme. (*)	automatic foam absorption system might have
	been activated due to too much detergent usage.

(*) Machine does not switch to spinning step when the laundry is not evenly distributed in the drum to prevent any damage to the machine and to its surrounding environment. Laundry should be rearranged and re-spun.

(**) Regular drum cleaning is not applied. Clean the drum regularly. See 4.4.2

A

26 / EN

Washing Machine / User’s Manual

Waschmaschine

Bedienungsanleitung

WTV 7711 BW0

DE

Dokument Nummer= 2820526731_DE/12-03-18.(17:39)

1 Allgemeine Sicherheitshinweise

Dieser Abschnitt enthält Sicherheitsanweisungen, die bei der Verhinderung von Verletzungen und Materialschäden helfen können. Alle Arten von Garantien erlöschen, falls diese

Anweisungen nicht beachtet werden.

1.1 Vermeidung von Personenund Sachschäden

uStellen Sie das Produkt niemals auf einen Teppichboden. Elektrische Teile überhitzen, da Luft nicht unter dem Gerät zirkulieren kann. Dies kann zu Problemen mit Ihrem Gerät führen.

uZiehen Sie den Netzstecker, wenn Sie das Gerät nicht benutzen.

uLassenSieInstallations-undReparaturarbeitengrundsätzlichvom autorisierten Kundendienst ausführen. Der Hersteller haftet nicht bei Schäden, die durch Aktivitäten nicht autorisierter Personen entstehen.

uWasserzulaufund Wasserablaufschläuche müssen fixiert und dürfen nicht beschädigt werden. Andernfalls kann Wasser lecken.

uÖffnen Sie niemals die Tür des Gerätes, nehmen Sie niemals den Filter heraus, wenn sich noch Wasser im Produkt befindet. Andernfalls besteht Überschwemmungsgefahr und Verletzungsgefahr durch heißes Wasser.

uVersuchen Sie niemals, die Waschmaschinentür mit Gewalt zu öffnen. Die Tür lässt sich erst ein paar Minuten nach dem Ende des Waschzyklus öffnen. Falls Sie versuchen, die Tür gewaltsam zu öffnen, können Tür und Sperrmechanismus beschädigt werden.

Dieses Produkt wurde mit Hilfe neuester Technologie unter umweltfreundlichen Bedingungen hergestellt.

28 / DE

Waschmaschine / Bedienungsanleitung