ASUS ROG Strix B360-H Gaming Service Manual

ROG STRIX B360-H GAMING

Motherboard

E13782

First Edition

February 2018

Copyright© 2018 ASUSTeK COMPUTER INC. All Rights Reserved.

No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).

Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing.

ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.

SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.

Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe.

Offer to Provide Source Code of Certain Software

This product contains copyrighted software that is licensed under the General Public License (“GPL”), under the Lesser General Public License Version (“LGPL”) and/or other Free Open Source Software Licenses. Such software in this product is distributed without any warranty to the extent permitted by the applicable law. Copies of these licenses are included in this product.

Where the applicable license entitles you to the source code of such software and/or other additional data, you may obtain it for a period of three years after our last shipment of the product, either

(1)for free by downloading it from https://www.asus.com/support/

or

(2)for the cost of reproduction and shipment, which is dependent on the preferred carrier and the location where you want to have it shipped to, by sending a request to:

ASUSTeK Computer Inc.

Legal Compliance Dept.

15 Li Te Rd.,

Beitou, Taipei 112

Taiwan

In your request please provide the name, model number and version, as stated in the About Box of the product for which you wish to obtain the corresponding source code and your contact details so that we can coordinate the terms and cost of shipment with you.

The source code will be distributed WITHOUT ANY WARRANTY and licensed under the same license as the corresponding binary/object code.

This offer is valid to anyone in receipt of this information.

ASUSTeK is eager to duly provide complete source code as required under various Free Open Source Software licenses. If however you encounter any problems in obtaining the full corresponding source code we would be much obliged if you give us a notification to the email address [e-mail], stating the product and describing the problem (please DO NOT send large attachments such as source code archives, etc. to this email address).

ii

Contents

Safety information.......................................................................................................	v
About this guide..........................................................................................................	vi
ROG STRIX B360-H GAMING specifications summary.........................................	viii
Package contents.......................................................................................................	xi
Installation tools and components...........................................................................	xii

Chapter 1:		Product Introduction
1.1	Motherboard overview...............................................................................		1-1
	1.1.1	Before you proceed.....................................................................	1-1
	1.1.2	Motherboard layout......................................................................	1-2
	1.1.3	Central Processing Unit (CPU)....................................................	1-4
	1.1.4	System memory...........................................................................	1-5
	1.1.5	Expansion slots............................................................................	1-7
	1.1.6	Jumpers.......................................................................................	1-8
	1.1.7	Onboard LEDs.............................................................................	1-9
	1.1.8	Internal connectors....................................................................	1-10

Chapter 2:		Basic Installation
2.1	Building your PC system...........................................................................		2-1
	2.1.1	CPU installation...........................................................................	2-1
	2.1.2	Cooling system installation..........................................................	2-3
	2.1.3	Motherboard installation..............................................................	2-5
	2.1.4	DIMM installation.........................................................................	2-6
	2.1.5	ATX power connection.................................................................	2-7
	2.1.6	SATA device connection..............................................................	2-7
	2.1.7	Front I/O connector......................................................................	2-8
	2.1.8	Expansion card installation..........................................................	2-9
	2.1.9	M.2 installation...........................................................................	2-10
2.2	Motherboard rear and audio connections..............................................		2-11
	2.2.1	Rear I/O connection...................................................................	2-11
	2.2.2	Audio I/O connections................................................................	2-13
2.3	Starting up for the first time....................................................................		2-15
2.4	Turning off the computer.........................................................................		2-15

Chapter 3:		BIOS Setup
3.1	Knowing BIOS.............................................................................................		3-1
3.2	BIOS setup program...................................................................................		3-2
	3.2.1	EZ Mode......................................................................................	3-3
	3.2.2	Advanced Mode...........................................................................	3-4
	3.2.3	QFan Control...............................................................................	3-7

iii

3.3	My Favorites................................................................................................		3-9
3.4	Main menu.................................................................................................		3-11
3.5	Ai Tweaker menu......................................................................................		3-11
3.6	Advanced menu........................................................................................		3-12
	3.6.1	Platform Misc Configuration.......................................................	3-12
	3.6.2	CPU Configuration.....................................................................	3-12
	3.6.3	System Agent (SA) Configuration..............................................	3-12
	3.6.4	PCH Configuration.....................................................................	3-12
	3.6.5	PCH Storage Configuration.......................................................	3-13
	3.6.6	PCH-FW Configuration..............................................................	3-13
	3.6.7	Onboard Devices Configuration.................................................	3-13
	3.6.8	APM Configuration.....................................................................	3-14
	3.6.9	USB Configuration.....................................................................	3-14
	3.6.10	Network Stack Configuration.....................................................	3-14
	3.6.11	HDD/SSD SMART Information..................................................	3-15
3.7	Monitor menu............................................................................................		3-15
3.8	Boot menu.................................................................................................		3-15
3.9	Tool menu..................................................................................................		3-16
	3.9.1	ASUS EZ Flash 3 Utility.............................................................	3-16
	3.9.2	Secure Erase.............................................................................	3-17
	3.9.3	ASUS SPD Information..............................................................	3-17
	3.9.4	Graphics Card Information.........................................................	3-17
3.10	Exit menu...................................................................................................		3-18
3.11	Updating BIOS..........................................................................................		3-18
	3.11.1	EZ Update..................................................................................	3-18
	3.11.2	ASUS EZ Flash 3.......................................................................	3-19
	3.11.3	ASUS CrashFree BIOS 3..........................................................	3-21

Appendix

Notices .....................................................................................................................	A-1
ASUS contact information......................................................................................	A-5

iv

Safety information

Electrical safety

•To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system.

•When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.

•Before connecting or removing signal cables from the motherboard, ensure that all power cables are unplugged.

•Seek professional assistance before using an adapter or extension cord. These devices could interrupt the grounding circuit.

•Ensure that your power supply is set to the correct voltage in your area. If you are not sure about the voltage of the electrical outlet you are using, contact your local power company.

•If the power supply is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer.

Operation safety

•Before installing the motherboard and adding devices on it, carefully read all the manuals that came with the package.

•Before using the product, ensure all cables are correctly connected and the power cables are not damaged. If you detect any damage, contact your dealer immediately.

•To avoid short circuits, keep paper clips, screws, and staples away from connectors, slots, sockets and circuitry.

•Avoid dust, humidity, and temperature extremes. Do not place the product in any area where it may become wet.

•Place the product on a stable surface.

•If you encounter technical problems with the product, contact a qualified service technician or your retailer.

v

About this guide

This user guide contains the information you need when installing and configuring the motherboard.

How this guide is organized

This guide contains the following parts:

1.Chapter 1: Product Introduction

This chapter describes the features of the motherboard and the new technology it supports. It includes description of the switches, jumpers, and connectors on the motherboard.

2.Chapter 2: Basic Installation

This chapter lists the hardware setup procedures that you have to perform when installing system components.

3.Chapter 3: BIOS Setup

This chapter tells how to change system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.

Where to find more information

Refer to the following sources for additional information and for product and software updates.

1.ASUS website

The ASUS website (www.asus.com) provides updated information on ASUS hardware and software products.

2.Optional documentation

Your product package may include optional documentation, such as warranty flyers, that may have been added by your dealer. These documents are not part of the standard package.

vi

Conventions used in this guide

To ensure that you perform certain tasks properly, take note of the following symbols used throughout this manual.

DANGER/WARNING: Information to prevent injury to yourself when trying to complete a task.

CAUTION: Information to prevent damage to the components when trying to complete a task.

IMPORTANT: Instructions that you MUST follow to complete a task.

NOTE: Tips and additional information to help you complete a task.

Typography

Bold text	Indicates a menu or an item to select.
Italics	Used to emphasize a word or a phrase.
<Key>	Keys enclosed in the less-than and greater-than sign
	means that you must press the enclosed key.
	Example: <Enter> means that you must press the Enter or
	Return key.
<Key1> + <Key2> + <Key3>	If you must press two or more keys simultaneously, the key
	names are linked with a plus sign (+).

vii

ROG STRIX B360-H GAMING specifications summary

		Intel® Socket LGA1151 for 8th Generation Core™ Processors**
		Supports 14nm CPU
	CPU	Supports Intel® Turbo Boost Technology 2.0*
		* The support of these features depends on the CPU types.
		** Refer to www.asus.com for Intel® CPU support list.
	Chipset	Intel® B360 Chipset
		4 x DIMM, max. 64GB DDR4 2666** / 2400 / 2133 MHz non-ECC, un-buffered
		memory
		Dual channel memory architecture
	Memory	Supports Intel® Extreme Memory Profile (XMP)*
		* Hyper DIMM support is subject to the physical characteristics of individual CPUs.
		Please refer to Memory QVL(Qualified Vendors List) for details.
		** DDR4 2666MHz memory frequency is only supported by 8th Generation Intel®
		6-core processors. Higher memory modules will run at the maximum transfer rate
		of DDR4 2666MHz.
		Integrated Graphics Processor - Intel® HD Graphics support
		Multi-VGA output support: HDMI / DVI-D ports
	Graphics	- Supports HDMI with max. resolution 4096 x 2160@24Hz
		- Supports DVI-D with max. resolution 1920 x 1200@60Hz
		Maximum shared memory of 1024MB
	Multi-GPU	Supports AMD 2-Way CrossFireX Technology
	support
		1 x PCIe 3.0/2.0 x16 slot (x16 mode)
		1 x PCIe 3.0/2.0 x16 slot (max at x4 mode)*
	Expansion	4 x PCIe 3.0/2.0 x1 slots**
		* PCIe x16_2 slot shares bandwidth with PCIe x1_3 and PCIe x1_4 slots. When PCIe
	slots
		x1_3 and PCIe x1_4 slots are occupied, PCIe x16_2 slot runs at x2 mode.
		** When both PCIe x1_1 and PCIe x1_2 slots are occupied, only the device installed
		into the PCIe x1_1 slot can be detected. Adjust BIOS settings to use PCIe x1_2
		slot.
		Intel® B360 Chipset
		- 1 x M.2_1 Socket 3 with M key, type 2242/2260/2280 storage devices
		support (both SATA & PCIe modes)*
		- 1 x M.2_2 Socket 3 with M key, type 2242/2260/2280/22110 storage devices
		support (PCIe 3.0 x 4 mode)**
	Storage	- 6 x SATA 6Gb/s ports
		- Intel® Optane™ Memory Ready
		* The M.2_1 socket shares bandwidth with the SATA6G_2 port when using M.2
		SATA mode device. Adjust BIOS settings to use SATA device.
		** The M.2_2 socket supports Intel® Optane™ Technology. Intel® Optane™
		Technology is only supported when using 8th Generation Intel® processors.
		Before using Intel® Optane™ memory modules, ensure that you have updated your
		motherboard drivers and BIOS to the latest version from ASUS support website.
		Intel® I219-V Gigabit LAN - Dual interconnect between the integrated Media
	LAN	Access Controller (MAC) and physical layer (PHY)
		Anti-surge LANGuard
		ROG GameFirst Technology
		(continued on the next page)

viii

ROG STRIX B360-H GAMING specifications summary

ROG SupremeFX S1220A 8-Channel High Definition Audio CODEC

-Supports up to 32-Bit/192kHz playback

-Impedance sense for front and rear headphone outputs

-High quality 120dB SNR stereo playback output and 113dB SNR recording input

-SupremeFX Shielding Technology

	Audio	- Dual Op Amplifiers
		- Supports Jack-detection, Multi-streaming, and Front Panel Jack-retasking
		- Optical S/PDIF out port at back panel
		Audio Features:
		- Sonic Radar III
		- Sonic Studio III + Sonic Studio Link
		Intel® B360 Chipset
		- 2 x USB 3.1 Gen 2 ports (2 ports at back panel, red, Type-A)*
	USB	- 4 x USB 3.1 Gen 1 ports (2 ports at back panel [Blue], 2 ports at mid-board)
		- 6 x USB 2.0 ports (2 ports at back panel, 4 ports at mid-board)
		* Supports 3A power output, one at a time only.
		ROG RAMCache II
	ROG exclusive	ROG CPU-Z
		ROG CloneDrive
	features
		ROG Overwolf
		ROG GameFirst IV
		ASUS Exclusive Features
		- AI Suite 3
		- AI Charger
		ASUS EZ DIY
		- ASUS CrashFree BIOS 3
		- ASUS EZ Flash 3
		ASUS Q-Design
		- ASUS Q-Shield
		- ASUS Q-LED (CPU, DRAM, VGA, Boot Device LED)
	ASUS special	- ASUS Q-Slot
		- ASUS Q-DIMM
	features
		Gamer’s Guardian
		- SafeSlot
		- DIGI+ VRM
		- DRAM Overcurrent Protection
		- ESD Guards on LAN, Audio, KBMS and USB ports
		- Highly Durable Components
		- Stainless Steel Back I/O
		AURA
		- Aura Lighting Control
		- Aura Lighting Effects Synchronization with compatible ASUS ROG devices
		(continued on the next page)

ix

ROG STRIX B360-H GAMING specifications summary

		1 x PS/2 keyboard/mouse combo port
		1 x HDMI port
		1 x DVI-D port
	Rear Panel I/O	2 x USB 3.1 Gen 2 ports Type-A [red]
		2 x USB 3.1 Gen 1 ports [blue]
	Ports
		2 x USB 2.0 ports [black]
		1 x Anti-surge LAN (RJ45) port
		5 x Audio jacks
		1 x Optical S/PDIF out
		1 x USB 3.1 Gen 1 connector supports additional 2 USB 3.1 Gen1 ports
		2 x USB 2.0 connectors support additional 4 USB 2.0 ports
		1 x M.2_1 Socket 3 with M key, type 2242/2260/2280 storage devices
		support (SATA & PCIe 3.0 x2 modes)
		1 x M.2_2 Socket 3 with M key, type 2242/2260/2280/22110 storage devices
		support (PCIe 3.0 x4 mode)
		6 x SATA 6Gb/s connectors
		1 x 4-Pin CPU_FAN connector
		1 x 4-Pin CPU_OPT fan connector
	Internal I/O	1 x 4-Pin AIO_PUMP connector
	connectors	2 x 4-Pin CHA_FAN connectors
		1 x 24-pin EATX power connector
		1 x 8-pin EATX 12V power connector
		1 x System panel connector
		1 x Clear CMOS jumper
		1 x Thermal sensor header
		1 x 14-1 pin TPM connector
		1 x Aura RGB Strip Header
		1 x Front panel audio connector (AAFP)
		1 x 128 Mb Flash ROM, UEFI AMI BIOS, PnP, SM BIOS 3.1, ACPI 6.1,
	BIOS Features	Multi-language BIOS, ASUS EZ Flash 3, CrashFree BIOS 3, Secure Erase,
		User Profile, F6 Qfan Control, F3 My Favorites, Last Modified log, F12
		PrintScreen, F4 AURA ON/OFF and F9 Search
	Manageability	WOL, PXE
		Drivers
	Support DVD	ASUS Utilities
	contents	EZ Update
		Anti-virus software (OEM version)
	Operating	Windows® 10 64-bit
	system support
	Form factor	ATX Form Factor, 12”x 9.6” (30.5cm x 24.4cm)

Specifications are subject to change without notice. Please refer to the ASUS website for the latest specifications.

x

Package contents

Check your motherboard package for the following items.

Motherboard	1 x ROG STRIX B360-H GAMING motherboard
Cables	4 x SATA 6Gb/s cables
	1 x Cable Ties set
	1 x ROG Strix Series sticker
Accessories	1 x ROG Strix Series Door Hanger
	2 x M.2 Screws Packages
	1 x Extension Cable for RGB strips (80 cm)
Application drive	1 x ROG motherboard support DVD
Documentation	1 x User guide

If any of the above items is damaged or missing, contact your retailer.

xi

Installation tools and components

Intel® LGA1151 CPU

Intel® LGA1151 compatible CPU Fan

PC chassis	SATA hard disk drive	Phillips (cross) screwdriver

1 bag of screws

DIMM

Power supply unit

SATA optical disc drive (optional)

Graphics card

The tools and components listed above are not included in the motherboard package.

xii

Product Introduction

1

1.1Motherboard overview

1.1.1Before you proceed

Take note of the following precautions before you install motherboard components or change any motherboard settings.

•Unplug the power cord from the wall socket before touching any component.

•Before handling components, use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, to avoid damaging them due to static electricity.

•Hold components by the edges to avoid touching the ICs on them.

•Whenever you uninstall any component, place it on a grounded antistatic pad or in the bag that came with the component.

•Before you install or remove any component, ensure that the ATX power supply is switched off or the power cord is detached from the power supply. Failure to do so may cause severe damage to the motherboard, peripherals, or components.

Chapter 1

ROG STRIX B360-H GAMING

1-1

1 Chapter

1.1.2Motherboard layout

1

2

3

2

4

24.4cm(9.6in)

KBMS_USB78

EATX12V

DIGI

CPU_FAN

+VRM

BOOT_DEVICE_LED

VGA_LED

CPU_OPT

DRAM_LED

CPU_LED

5

DVI

DIMMDDR4B1 (64bit, 288-pin module)

DIMMDDR4B2* (64bit, 288-pin module)

DIMMDDR4A1 (64bit, 288-pin module)

DIMMDDR4A2* (64bit, 288-pin module)

AUDIO

LANGuard

EATXPWR

56

30.5cm(12in)

34

LGA1151

1

HDMI

U31G1

ASM

1562

LAN_U31G2_12

ASM

1562

CONBACKIO

AIO_PUMP

2280

2260

2242

1(SOCKET3)

U31G1_

6

M.2_1(SOCKET3)

PCIE

SATA

IRST

X2

V

X

PCIEX1_1

M.2

Intel	PCIEX16_1								7
								1
I219V								SATA6G
	BATTERY				Intel®			2
		ASM1480	ASM1480					SATA6G
Super					B360			3
	PCIEX1_2							SATA6G4	8
I/O
	PCIEX16_2							SATA6G_
						2(SOCKET3)M.2		5
	STRIX B360-H GAMING							SATA6G6SATA6G
	PCIEX1_3	22110	2280	2260	2242
					M.2_2(SOCKET3)		128Mb
					PCIE SATA IRST		BIOS
					X4 X V

PCIEX1_4				T_SENSOR	SB_PWR
CHA_FAN1	TPM	USB1011	USB914	CHA_FAN2	PANEL
		RGB_HEADER
AAFP
				CLRTC

16

2

15

14

13

2

12

11

10

9

Refer to 1.1.8 Internal connectors and 2.2.1 Rear I/O connection for more information about rear panel connectors and internal connectors.

1-2	Chapter 1: Product Introduction

Layout contents

Connectors/Jumpers/Buttons and switches/Slots		Page
1.	ATX power connectors (24-pin EATXPWR; 8-pin EATX12V)	1-16
2.	CPU, CPU optional, and chassis fan connectors; AIO pump connector	1-14
	(4-pin CPU_FAN; 4-pin CPU_OPT; 4-pin CHA_FAN1-2; 4-pin AIO_PUMP)
3.	LGA1151 CPU socket	1-4
4.	DDR4 DIMM slots	1-5
5.	Q LEDs (CPU, DRAM, VGA, BOOT)	1-9
6.	USB 3.1 Gen 1 connector (20-1 pin U31G1_56)	1-12
7.	M.2 sockets (M.2_1; M.2_2)	1-15
8.	Intel® Serial ATA 6 Gb/s connectors (7-pin SATA6G_1-6)	1-10
9.	Standby Power LED (SB_PWR)	1-9
10.	System panel connector (20-5 pin PANEL)	1-17
11.	Thermal sensor connector (2-pin T_SENSOR)	1-15
12.	Clear RTC RAM jumper (2-pin CLRTC)	1-8
13.	USB 2.0 connectors (10-1 pin USB1011, USB914)	1-12
14.	AURA RGB header (4-pin RGB_HEADER)	1-13
15.	TPM connector (14-1 pin TPM)	1-11
16.	Front panel audio connector (10-1 pin AAFP)	1-11

Chapter 1

ROG STRIX B360-H GAMING

1-3

1.1.3Central Processing Unit (CPU)

The motherboard comes with a surface mount LGA1151 socket designed for the 8th Generation Intel® Core™ processors.

1 Chapter

STRIX B360-H GAMING

ROG STRIX B360-H GAMING CPU LGA1151

Ensure that you install the correct CPU designed for LGA1151 socket only. DO NOT install a CPU designed for LGA1150, LGA1155 and LGA1156 sockets in the LGA1151 socket.

•Ensure that all power cables are unplugged before installing the CPU.

•Upon purchase of the motherboard, ensure that the PnP cap is on the socket and the socket contacts are not bent. Contact your retailer immediately if the PnP cap is missing, or if you see any damage to the PnP cap/socket contacts/motherboard components.

•Keep the cap after installing the motherboard. ASUS will process Return Merchandise Authorization (RMA) requests only if the motherboard comes with the cap on the LGA1151 socket.

•The product warranty does not cover damage to the socket contacts resulting from incorrect CPU installation/removal, or misplacement/loss/incorrect removal of the PnP cap.

1-4	Chapter 1: Product Introduction

1.1.4System memory

The motherboard comes with four DDR4 (Double Data Rate 4) Dual Inline Memory Modules (DIMM) slots.

A DDR4 module is notched differently from a DDR, DDR2, or DDR3 module. DO NOT install a DDR, DDR2, or DDR3 memory module to the DDR4 slot.

DIMM B1 DIMM B2

DIMM A1 DIMM A2

STRIX B360-H GAMING

ROG STRIX B360-H GAMING 288-pin DDR4 DIMM sockets

Recommended memory configurations

Chapter 1

DIMM_B2*

DIMM_A2*

DIMM_A2*

DIMM_B1 DIMM_B2* DIMM_A1 DIMM_A2*

ROG STRIX B360-H GAMING

1-5

1 Chapter

Memory configurations

You may install 1 GB, 2 GB, 4 GB, 8 GB and 16 GB unbuffered and non ECC DDR4 DIMMs into the DIMM sockets.

You may install varying memory sizes in Channel A and Channel B. The system maps the total size of the lower-sized channel for the dual-channel configuration. Any excess memory

from the higher-sized channel is then mapped for single-channel operation.

•The default memory operation frequency is dependent on its Serial Presence Detect (SPD), which is the standard way of accessing information from a memory module. Under the default state, some memory modules for overclocking may operate at a lower frequency than the vendor-marked value.

•For system stability, use a more efficient memory cooling system to support a full memory load (4 DIMMs).

•Memory modules with memory frequency higher than 2133 MHz and its corresponding timing or the loaded X.M.P. Profile is not the JEDEC memory standard. The stability and compatibility of these memory modules depend on the CPU’s capabilities and other installed devices.

•Always install the DIMMS with the same CAS Latency. For an optimum compatibility, we recommend that you install memory modules of the same version or data code (D/C) from the same vendor. Check with the vendor to get the correct memory modules.

•ASUS exclusively provides hyper DIMM support function.

•Hyper DIMM support is subject to the physical characteristics of individual CPUs. Load the X.M.P. or D.O.C.P. settings in the BIOS for the hyper DIMM support.

•Visit the ASUS website for the latest QVL.

1-6	Chapter 1: Product Introduction

1.1.5Expansion slots

Unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components.

Chapter 1

PCIEX1_1

PCIEX16_1

PCIEX1_2

PCIEX16_2

STRIX B360-H GAMING

PCIEX1_3

PCIEX1_4

Slot No. Slot Description

1PCIe x1_1 slot

2PCIe x16_1 slot

3PCIe x1_2 slot 4 PCIe x16_2 slot 5 PCIe x1_3 slot

6PCIe x1_4 slot

		PCI Express 3.0 operating mode
	VGA configuration
		PCIe x16_1	PCIe x16_2
	Single VGA/PCIe card	x16 (single VGA	N/A
		recommended)
	Dual VGA/PCIe card	x16	x4

•We recommend that you provide sufficient power when running CrossFireX™ mode.

•Connect a chassis fan to the motherboard connector labeled CHA_FAN1-2 when using multiple graphics cards for better thermal environment.

ROG STRIX B360-H GAMING

1-7

1.1.6Jumpers

		1. Clear RTC RAM jumper (2-pin CLRTC)
		This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can
	1Chapter	clear the CMOS memory of date, time, and system setup parameters by erasing the
		CMOS RTC RAM data. The onboard button cell battery powers the RAM data in
		CMOS, which include system setup information such as system passwords.

STRIX B360-H GAMING

CLRTC

+3V_BAT GND

PIN 1

ROG STRIX B360-H GAMING Clear RTC RAM

To erase the RTC RAM:

1.Turn OFF the computer and unplug the power cord.

2.Short-circuit pin 1-2 with a metal object or jumper cap for about 5-10 seconds.

3.Plug the power cord and turn ON the computer.

4.Hold down the <Delete> key during the boot process and enter BIOS setup to re-enter data.

Except when clearing the RTC RAM, never remove the cap on CLRTC jumper default position. Removing the cap will cause system boot failure!

1-8	Chapter 1: Product Introduction

1.1.7Onboard LEDs

1.Q LEDs (CPU, DRAM, VGA, BOOT)

Q LEDs check key components (CPU, DRAM, VGA card, and booting devices) in sequence during motherboard booting process. If an error is found, the corresponding LED remains lit until the problem is solved. This user-friendly design provides an intuitive way to locate the root problem within seconds.

BOOT (YELLOW GREEN)

VGA (WHITE)

DRAM (YELLOW)

CPU (RED)

STRIX B360-H GAMING

ROG STRIX B360-H GAMING

CPU/DRAM/BOOT_DEVICE/VGA LED

The Q LEDs provide the most probable cause of an error code as a starting point for troubleshooting. The actual cause may vary from case to case.

2.Standby Power LED

The motherboard comes with a standby power LED. The LED lights up to indicate that the system is ON, in sleep mode, or in soft-off mode. This is a reminder that you should shut down the system and unplug the power cable before removing or plugging in any motherboard component. The illustration below shows the location of the onboard LED.

Chapter 1

SB_PWR
STRIX B360-H GAMING
ON	OFF
Standby Power	Powered Off

ROG STRIX B360-H GAMING Standby power LED

ROG STRIX B360-H GAMING

1-9

1 Chapter

1.1.8Internal connectors

1.Intel® Serial ATA 6 Gb/s connectors (7-pin SATA6G_1-6)

These connectors connect to Serial ATA 6 Gb/s hard disk drives via Serial ATA 6 Gb/s signal cables.

SATA6G_1

SATA6G_2

GND

GND

RSATA_TXP1

RSATA_TXP2

RSATA_TXN1

RSATA_TXN2

GND

GND

RSATA_RXN1

RSATA_RXN2

RSATA_RXP1

RSATA_RXP2

GND

GND

SATA6G_3

SATA6G_4

GND

GND

RSATA_TXP3

RSATA_TXP4

RSATA_TXN3

RSATA_TXN4

GND

GND

RSATA_RXN3

RSATA_RXN4

RSATA_RXP3

RSATA_RXP4

GND

GND

SATA6G_5

SATA6G_6

GND

GND

RSATA_TXP5

RSATA_TXP6

RSATA_TXN5

RSATA_TXN6

STRIX B360-H GAMING

GND

GND

RSATA_RXN5

RSATA_RXN6

RSATA_RXP5

RSATA_RXP6

GND

GND

ROG STRIX B360-H GAMING Intel® SATA 6 Gb/s connectors

1-10	Chapter 1: Product Introduction

2.Front panel audio connector (10-1 pin AAFP)

This connector is for a chassis-mounted front panel audio I/O module that supports HD Audio standard. Connect one end of the front panel audio I/O module cable to this connector.

AGND NC SENSE1 RETUR	SENSE2 RETUR	Chapter 1
AAFP
PORT1 L PORT1 R PORT2 R	SENSESEND PORT2 L
STRIX B360-H GAMING
HD-audio-compliant
pin definition

ROG STRIX B360-H GAMING Front panel audio connector

We recommend that you connect a high-definition front panel audio module to this connector to avail of the motherboard’s high-definition audio capability.

3.TPM connector (14-1 pin TPM)

This connector supports a Trusted Platform Module (TPM) system, which securely stores keys, digital certificates, passwords and data. A TPM system also helps enhance network security, protect digital identities, and ensures platform integrity.

TPM

STRIX B360-H GAMING

F CLKRUN F SERIRQ F FRAME# F LAD3 F LAD2 F LAD1 F LAD0

PIN 1

+3VSB S PCIRST# TBD

GND C PCICLK TPM +3V +3V

ROG STRIX B360-H GAMING TPM connector

The TPM module is purchased separately.

ROG STRIX B360-H GAMING

1-11