ADB1400AWQ5
Amana ADB1400AWQ5, ADB1400AWB5, IUD8000WQ5, IUD8000WS5, IWU98665 Installation Instructions Manual
...
INSTALLATIONINSTRUCTIONS
UNDERCOUNTERDISHWASHER
PLASTICGIANT TUBMODELS
INSTRUCTIONSD'INSTALLATION
LAVE-VAISSELLESOUSCOMPTOIR
MODELESA TRESGRANDE CUVE EN PLASTIQUE
Table of Contents .............................................................. 2
Table des matieres .......................................................... 24
W10435039A
TABLEOF CONTENTS
DISHWASHER SAFETY ............................................................................... 2
INSTALLATION REQUIREMENTS ............................................................. 3
Tools and Parts ......................................................................................... 3
Location Requirements ............................................................................. 4
Drain Requirements .................................................................................. 6
Water Supply Requirements ..................................................................... 6
Electrical Requirements ............................................................................ 6
INSTALLATION INSTRUCTIONS ............................................................... 7
Prepare Cabinet Opening--Existing Utilities ............................................ 7
Prepare Cabinet Opening-- New Utilities ................................................. 7
Prepare and Route Water Line ................................................................. 8
Install Drain Hose ...................................................................................... 9
Prepare Dishwasher ................................................................................ 11
INSTALLATION INSTRUCTIONS (CONT.)
Make Power Supply Cord Connection .................................................. 12
Determine Cabinet Opening ................................................................... 14
Choose Attachment Option .................................................................... 15
Prepare Water Supply Line ..................................................................... 15
Move Dishwasher Close to Cabinet Opening ........................................ 16
Connect to Water Supply ....................................................................... 18
Connect to Drain ..................................................................................... 18
Make Direct Wire Electrical Connection ................................................. 19
Secure Dishwasher in Cabinet Opening ................................................ 20
Complete Installation .............................................................................. 22
Check Operation ..................................................................................... 23
If Dishwasher Does Not Operate ............................................................ 23
Additional Tips ........................................................................................ 23
DISHWASHERSAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
You Need to:
• Slowly open dishwasher door while someone grasps the rear
of the dishwasher. Remove shipping materials, drain hose and
lower rack. Close dishwasher door until latched.
• Observe all governing codes and ordinances.
• Install this dishwasher as specified in these instructions.
• Installation should be performed by a qualified service
technician. The dishwasher must be installed to meet all
Tip Over Hazard
Do not use dishwasher until completely installed.
electrical and plumbing national and local codes and
ordinances.
Do not push down on open door.
Doing so can result in serious injury or cuts.
2
INSTALLATIONREQUIREMENTS
Gather the recommended tools and parts before starting
installation. Read and follow the instructions provided with any
tools listed here.
All Installations
Tools needed:
Parts needed:
3 " 3 " " "
Y8Comprx _ hoseflttmg
For part or kit. see local
retailer or call Whirlpool
Parts: 1:800.442-9991, Part
Number W10273460
Pliers
Phillips
screwdriver
5A6"and 1A"
or ruler
Measuring tape
10" adjustable wrench _
that opens to _
11/8 (2.9 cm)
*Must be the proper size to connect your household wiring
to 16-gauge wiring in dishwasher.
Other useful items you may need:
Shal,ow __
pan _ I tOwel _ I
Parts supplied:
Drain hose Drain #10x ½,, 2. under]
Clamps (2)hose Phillips.head counter
! small)brackets
sCrews (2) mounting
Flat-bladescrewdriver
Utility knife
UL Listed/CSA
Approved twist-on _ _
wire connectors*
Small level S
%" open-end
wrench
Other parts you may also need:
for solid surface
4396277)
NOTE: Some parts available for purchase in plumbing supply
stores. Check local codes. Check existing electrical supply. See
"Electrical Requirements" section. It is recommended that
electrical connections be made by a licensed electrical installer.
In addition, for first-time installations
Toolsneeded:
with 1/2'!;¾"
Parts needed:
Copper tubing (%" See '_Electrical Requirements" section.
O.D.suggested) or
flexible bra'ded For D rect W re" For Power Supp y
r i lin useULLsted/ Cord'useUL
wate supp y e
CSA Approved Listed/CSA
(1 large and
Make sure all these parts are included in the literature package.
t®TORX and T20 are registered trademarks of Saturn Fasteners, Inc.
tt(._t... J)_)).) I tofit%' (2.2cm) supplyCord kit
I strain relief IApproved Power
I h01e I marked f0iUse with
' dishwasher
@rounded electrical supply required.
Do not run drain lines, water lines or electrical wiring where they
can interfere with or contact dishwasher motor or legs.
The location where the dishwasher will be installed must provide
clearance between motor and flooring. Motor should not touch
the floor.
Do not install dishwasher over carpeted flooring.
Shelter dishwasher and water lines leading to dishwasher against
freezing. Damage from freezing is not covered by the warranty.
A side panel kit is available from your dealer for installing your
dishwasher at the end of your cabinetry.
A moisture barrier accessory (Part Number 4396277) is available
from your dealer for installing underneath the countertop.
Check location where dishwasher will be installed. The location
must provide:
• easy access to water, electricity and drain.
convenient access for loading and unloading dishes.
Corner locations require a 2" (5.1 cm) minimum clearance
between the side of the dishwasher door and the wall or
cabinet.
• square opening for proper operation and appearance.
• cabinet front perpendicular to floor.
• level floor. (If floor at front of opening is not level with floor
at rear of opening, shims may be needed to level
dishwasher.)
Helpful Tip: Be sure to accurately measure dimensions and
ensure dishwasher is level if the floor in the dishwasher opening is
uneven (example: Flooring extends only partway into opening).
NOTE: To avoid shifting during dishwasher operation, shims must
be securely attached to the floor.
If dishwasher will be left unused for a period of time or in a
location where it may be subject to freezing, have it winterized by
authorized service personnel.
Make sure pipes, wires and drain hose are within the shaded area
shown in the "Product and Cabinet Opening Dimensions" section.
_lnsulationmay
becompressed.
(notusedonallmodel
Check that all surfaces
have no protrusions that wpuld
rohibit dishwasher installation.
NOTE:Shadedareaofcabinetwallsshow
whereutilityconnectionsmay
beinstalled.
*Measuredfromthelowestpointonthe
undersideofthecountertop.Maybereduced
to33%"(86cm)byremovingrearlevelinglegs
fromdishwasher.
**Minimum,measuredfromnarrowestpointofopening.
A new drain hose is supplied with your dishwasher. If drain
hose is not long enough, use a new drain hose with a
maximum length of 12 ft (3.7 m) (Part Number 3385556) that
meets all current AHAM/IAPMO test standards, is resistant to
heat and detergent, and fits the 1" (2.5 cm) drain connector of
the dishwasher.
Make sure to connect drain hose to waste tee or disposer inlet
above drain trap in house plumbing and 20" (50.8 cm)
minimum above the floor. It is recommended that the drain
hose either be looped up and securely fastened to the
underside of the counter, or be connected to an air gap.
Make sure to use an air gap if the drain hose is connected to
house plumbing lower than 20" (50.8 cm) above subfloor or
floor.
Use 1/2"minimum I.D. drain line fittings.
If required, the air gap should be installed in accordance with
the air gap installation instructions. When you are connecting
the air gap, a rubber hose (not provided) will be needed to
connect to the waste tee or disposer inlet.
Be sure that the electrical connection and wire size are adequate
and in conformance with the National Electrical Code, ANSI/NFPA
70 - latest edition and all local codes and ordinances.
A copy of the above code standards can be obtained from:
National Fire Protection Association
1 Batterymarch Park
Quincy, MA 02269
You must have:
• 120-volt, 60 Hz, AC-only, 15- or 20-amp, fused electrical
supply.
• Copper wire only.
We recommend:
• A time-delay fuse or circuit breaker.
• Aseparate circuit.
If connecting dishwasher with a
power supply cord:
Use UL Listed power supply cord kit
(Part Number 4317824) marked for
use with dishwasher.
Power supply cord must plug into a grounded
3 prong outlet, located in the cabinet next to
the dishwasher opening. Outlet must meet all
local codes and ordinances.
If connecting dishwasher with direct wiring:
• Use flexible, armored or nonmetallic
sheathed, copper wire with
grounding wire that meets the
wiring requirements for your home
and local codes and ordinances.
• Use a UL Listed/CSA Approved strain relief.
pp)y 58eq(s emen s
A hot water line with 20 to 120 psi (188 to 862 kPa) water
pressure can be verified by a licensed plumber.
120°F (49°C) water at dishwasher.
3/8"O.D. copper tubing with compression fitting or flexible
braided water supply line (Part Number 4396897RP).
NOTE: 1/2"minimum plastic tubing is not recommended.
A 90° elbow with 3/4"hose connection with rubber washer.
Do not solder within 6" (15.2 cm) of the water inlet valve.
6
INSTALLATIONINSTRUCTIONS
Electrical Shock Hazard
Disconnect electrical power at the fuse box or circuit
breaker box before installing dishwasher.
Failure to do so can result in death or electrical shock.
I DisconneCt electrical p0we[ at the fuSe box 0r ciicuit i
Yes _Follow instructionslin the ,,Prepare cabinet
openingmExisting utilities, section:
_Vo --Follow instructions in the !,Prepare cabinet
Opening--New Utilities" section,
hookups ity hookups
J
If the water line and the cable extend to the locations shown,
proceed to the "Install Drain Hose" section. If they do not reach far
enough, follow the instructions in the "Prepare Cabinet Opening--
New Utilities" section.
Prepare and route the electrical supply
What type of electrical
connection will you use?
Direct Wire:
Fo,oW OptionB instructions
Option A, Power Supply Cord:
NOTE: A grounded 3 prong outlet is required inside a cabinet next
to the dishwasher cabinet opening.
1J Power Supply Cord_Drill
Uptmonallocation
Drill a 1V#' (3.8 cm) hole in cabinet side or rear.
See "Product and Cabinet Opening Dimensions" section.
Woodcabinet:Sandtheholeuntilsmooth.
Metalcabinet:Coverholewithgrommetincludedwithpower
supplycordkit.
OptionB, Direct Wire:
Helpful Tip: Wiring the dishwasher will be easier if you route the
cable into the cabinet opening from the right-hand side.
Drill a 1V2"(3.8 cm) hole in right-hand cabinet side or rear.
See "Product and Cabinet Opening Dimensions" section.
Route cable from power supply through cabinet hole (cable must
extend to the right front side of cabinet opening). Tape cable to
the floor in area shown. This will prohibit cable from moving when
dishwasher is moved into cabinet opening.
Helpful Tip: Routing the water line through the left side of cabinet
opening will make water connection easier.
Direct Wire-Prepare
Wood cabinet: Sand the hole until smooth.
Metal cabinet: Cover hole with grommet (Part Number 302797 -
not provided).
8
Drill a 1/2"(1.3 cm) hole in the cabinet side or rear.
.... q
(copper tubing only)
J
Measure overall length of copper tubing for the water supply line.
J
Attach the water supply line (copper tubing or flexible braided line)
to the hot water line using a connection configuration that is in
compliance with local codes and ordinances. The water supply to
the dishwasher should have a manual shutoff valve located under
the sink.
Slowly route water supply line through hole in cabinet. (If you are
using copper tubing, it will bend and kink easily, so be gentle.) It
should be far enough into the cabinet opening to connect it to the
dishwasher inlet on the front left side of the dishwasher.
Route water line and tape it to the floor in area shown. This will
keep it from moving when dishwasher is moved into cabinet
opening.
IMPORTANT: Always use a new drain hose. Check local codes to
determine whether an air gap is required.
If needed, drill a 1V2"(3.8 cm) diameter hole in cabinet wall or side
of the opening closest to the sink.
Slowly turn water shutoff valve to "ON" position. Flush water into
a shallow pan until clear to get rid of particles that could clog the
inlet valve. Turn shutoff valve to "OFF" position.
Route drain hose as shown through hole in cabinet to the front
center of opening where drain connection will be made. Tape
drain hose to the floor in area shown. This will prohibit it from
moving when dishwasher is moved into cabinet opening.
connectdrainhosetoWastetee0rWastedisposer
uslngoneofthefollowingoptions:
[ Qpti0n A; Waste disposer,n0 airga p
No Waste disposer- no a rgaP
[ Opt On C,Waste disposer- with a
Option D, No waste disposer - with air gap
Tip Over Hazard
Do not use dishwasher until completely installed.
Do not push down on open door.
Doing so can result in serious injury or cuts.
__}!}_}%;;,;;_;}_ %}_
1. Connect rubber end of drain hose to
air gap and cut if needed.
NOTE: Do not cut ribbed section.
2.
Attach drain hose to air gap with
large blue drain hose clamp
(provided). Use pliers to squeeze
clamp open and move into position.
If the drain hose was cut, use a 1V2"
to 2" (3.8 to 5.1 cm) screw-type
clamp (not provided).
3.
Use a rubber hose (not provided)
with screw-type clamps (not
provided) to connect from waste tee
to air gap.
Excessive Weight Hazard
Use two or more people to move and install
dishwasher.
Failure to do so can result in back or other injury.
Attach insulation
Using the precut slots in the insulation, fasten the insulation over
the molded hooks on the tub. Be sure to fasten the insulation
down on both sides of the tub.
Helpful Tip: Place cardboard under dishwasher until installed in
cabinet opening to avoid damaging floor covering. Do not use
door panel as a worktable without first covering with a towel to
avoid scratching the door panel.
11
Using 2 or more people, grasp sides of dishwasher door frame
and place dishwasher on its back.
Remove panel and fasl
Using a flat-blade screwdriver, turn the plastic fasteners 1/4turn to
unlock them. Remove panel. Do not remove tech sheet from
access panel.
Install a UL Listed/CSA Approved strain relief. Make sure screw
heads are facing to the left when tightening conduit nut. Strain
relief is provided with the power supply cord kit.
..... /
connection will you use?
NOTE: If using Option B, proceed to "Determine Cabinet
Opening," to continue with the installation of your dishwasher.
Option A, Power Supply Cord:
Using a 1/4"hex head socket, nut driver or Torx T20 screwdriver,
remove terminal box cover. Retain for later use.
12
® ®
Route cord so that it does not touch dishwasher motor to lower
part of dishwasher tub. Pull cord through strain relief in terminal
box.
Select UL Listed/CSA Approved twist-on wire connectors rated to
connect your power supply cord to 16-gauge dishwasher wiring.
Connect wires black to black and white to white, using UL
Listed/CSA Approved twist-on wire connectors.
Electrical Shock Hazard
ElectricMly ground dishwasher.
Connect ground wire to green ground connector in
terminal box.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
If needed, see website for animated representation of this step.
Visit www.whirlpool.com/electrical under FAQ tab.
e)
Tighten strain relief screws to secure cord.
/
Remove the green grounding screw and place through the ring
terminal of the green ground wire. Reattach and tighten the green
screw.
Power Cord--Connect
remaining wires .........................................
NOTE: Do not pre-twist stranded wire. Twist on wire connector.
Gently tug on wires to be sure both are secured.
Place wires inside terminal box. Insert tabs on left side of cover.
Make sure wires are tucked inside box. Close cover ensuring
wires are not pinched. Use 1/4"nut driver or Torx®T20®
screwdriver and previously removed screw to secure cover.
NOTE: Do not plug into outlet until instructed to do so.
13
Your dishwasher has leveling legs• The following provides
instructions to adjust the leveling legs to set the dishwasher to the
correct height for your cabinet opening•
Measure height of cabinet opening from underside of countertop
to floor where dishwasher will be installed (you will need to
measure the lowest point on the underside of the countertop and
the highest point on the floor). Refer to "Dishwasher Height
Adjustment Chart" to adjust the leveling legs.
Cabinet Front legs Rear legs
opening height heightA I height B
NOTE: If the minimum cabinet opening height is less than
34" (86.4 cm), the rear leveling legs can be removed for additional
clearance. This will allow the dishwasher to fit into a 337/8'' (86 cm)
high cabinet opening, but the dishwasher will be more difficult to
move. (Measurements are approximate. Rear and front leveling
legs are preset at the factory for 34W' [87.6 cm].)
Turn front and rear leveling legs to the same height. Refer to
"Dishwasher Height Adjustment Chart."
34" (86.4 cm) %" (22 mm) ¾' (17.5 mm)
I
34_/2'' (87.6 cm) 1W' (28.8 mm) 1" (24.3 ram)
Front legs -
/
14
Built-up floors: If the kitchen floor is higher than the cabinet
opening's floor - for example, the kitchen floor tile does not
extend into the cabinet opening - add shims as needed in the area
shown to bring the dishwasher up to 34" (86.4 cm) below the
countertop.
NOTE: Shims must be securely attached to floor to avoid
movement when the dishwasher is in use.
Option 1, Countertop Attachment
Remove the brackets from the package and insert into the open
slots on the left and right-hand top of the dishwasher collar as
shown.
Excessive Weight Hazard
Use two or more people to move and install
dishwasher.
Failure to do so can result in back or other injury.
Using 2 or more people, stand the dishwasher up.
IMPORTANT: The dishwasher must be secured to the cabinet.
There are two brackets found in the parts bag. Attach the
brackets using Option Number 1 if the countertop is wood,
laminate or another similar surface. If your countertop is marble,
granite or another hard surface, install using Option Number 2.
Using a pair of pliers, bend the tab down to secure the bracket in
place. Repeat this step for the other side.
NOTE: Do not attach the dishwasher. This will be done later.
Option 2, Side Attachment
For marble, granite, or other hard surface countertops
Order Mounting Bracket Kit Part Number 8212560.
.J Slide nut and ferrule onto
tubing (copper tubing only)
Copper tubing only: Slide nut, then ferrule, about 1" (2.5 cm) onto
copper tubing.
NOTE: To avoid vibration during operation, route the water supply
line so that it does not touch the dishwasher base, frame or motor.
15
Loading...