Delta 36-755, 36-751 User Manual

10” Tilting Arbor Saw

High quality and feature loaded.

•Magnetic motor starter with overload and no-voltage

•Full cabinet with motor cover for sawdust containment.

•Built-in storage for miter gage, rip fence and blade wrench.

•Extra-large cast-iron table with extension wings provides ample support for large work.

•Integral T-slot grooves prevent miter gage from falling during cut-off operations.

•Convenient up-front blade tilting controls for safe, easy

Model 36-755 10” Tilting Arbor

Includes basic machine with Jet- Micro-Set® rip fence; see-thru blade splitter and anti-kickback attachment; graduated guide bar, rear guide bar, gage, 10” dia. saw blade, table

and motor pulleys, V-belt, (2) table

wings, motor cover; 2HP, 230V, single phase, 60 Hz., TEFC motor; motor starter and instruction manual.

®

Model 36-755 10” Tilting Arbor Saw

Model 36-751 10” Tilting Arbor Saw with 30” Unifence® Saw Guide. Same as Model 36-755 above less Jet-Lock® , Micro-Set® rip fence with front and rear guide bars and (1) table extension wing, but with Unifence® Saw Guide which includes fence, carriage assembly, front guide bar, table frame, legs and mounting hardware. Less table board.

Model 36-752 10” Tilting Arbor Saw with 52” Unifence® Saw Guide. Same as Model 36-755 above less Jet-Lock® , Micro-Set® rip fence with front and rear guide bars and (1) table extension wing, but with Unifence® Saw Guide which includes fence, carriage assembly, front guide bar, table frame, legs, shelf support brackets and mounting hardware. Less table and shelf boards.

Model 36-751 10” Tilting Arbor Saw with 30” Unifence Saw Guide and 34-914 Accessory Table Board.

Model 36-752 10” Tilting Arbor Saw with 52” Unifence Saw Guide

and 34-998 Accessory Table and Shelf Boards.

Cuts stock 31⁄8” thick; a full 21⁄8” at 45° blade tilt. 2 HP motor delivers plenty of power for fast, efficient cutting.

Unique “table top located” adjusting screws for accurate setting of 45° and 90° positive blade stops.

SPECIFICATIONS

Motor ...........................................	2 HP, 230V, 60 Hz., single phase
Blade:
Diameter ....................................................................		10” (254 mm)
Arbor .............................................................................		5⁄8” (16 mm)
Speed ...............................................................................		4000 rpm
Capacity:		31⁄8” (79 mm)
Max. depth of cut 90° .................................................
Max. depth of cut 45° .................................................		21⁄8” (54 mm)
Max. rip R of blade ....................................................		25” (635 mm)
Max. rip L of blade ..................................................		151⁄2” (394 mm)
Max. rip R of blade w/30” Unifence Saw Guide		........ 30” (762 mm)
Max. rip R of blade w/52” Unifence Saw Guide ......		52” (1321 mm)
Max. rip L of blade w/30” or		83⁄4” (222 mm)
52” Unifence Saw Guide .......................................
Table in front of saw blade at		121⁄4” (311 mm)
max. cutting height ..............................................
Max. width of dado .....................................................		13⁄16” (21 mm)

Table:
Size w/extension wings ..........................	36” x 27” (914 x 686 mm)
Size w/ext. wing and 30”	621⁄2” x 27” (1588 x 686 mm)
Unifence Saw Guide ......................
Size w/ext. wing and 52”	781⁄2” x 27” (1994 x 686 mm)
Unifence Saw Guide ......................
Height ......................................................................	341⁄4" (870 mm)
Miter gage groove ........................................	3⁄8” x 3⁄4” (10 x 19 mm)
Overall Dimensions:
Width .......................................................................	45” (1143 mm)
Width w/30” Unifence Saw Guide ........................	671⁄2” (1715 mm)
Width w/52” Unifence Saw Guide ...........................	83” (2108 mm)
Depth .........................................................................	32” (813 mm)
Height ........................................................................	39” (991 mm)
Weight: Model 36-755 .........................................	288 Ibs. (131 kg)
Model 36-751 .........................................	290 Ibs. (132 kg)
Model 36-752 .........................................	293 Ibs. (133 kg)

5	For accessories, see page 27

Model 36-445

10” Contractor’s Saw® with 30” Unifence Saw Guide

10” Contractor’s Saw®

New Series 2000 10˝ Contractor’s Saws take woodworking into the next century.

•Series 2000 10˝ Contractor’s Saws are available with your choice of the UniRip Fence, Unifence® , Precision Saw Guide or Biesemeyer Saw Fence systems.

•New UniRip T-Square style fence (model 36-444 only) offers up to 30˝ of right-hand cutting capacity. Provides additional stock support in front of the blade and includes built-in T-slots for adding jigs or other accessories.

•Each Series 2000 10˝ Contractor’s Saw comes with a new sturdy steel stand that features an integral dust chute for improved dust collection and built-in storage for rip fence, miter gage and blade wrenches.

•Maximum 31⁄8” depth of cut at 90°; 21⁄8” at 45° for clean cutting of standard stock sizes.

•Patented Auto-Set® T-Slot miter gage with

adjustable stops at 90° and 45° positions for accurate straight and angle cutting.

• Integral T-slot table grooves prevent miter gage from falling during wide cut-off operations.

•Extra-large table provides ample support for large work.

•Unique “table top located” adjusting screws for accurate setting of 45° & 90° positive blade stops.

•Large on/off paddle switch is positioned near the top of the table for quick access.

•Convenient up-front blade raising and tilting controls for safe, easy operation.

•Heavy-duty 11⁄2 HP induction motor delivers plenty of extra power and speed for the toughest cutting jobs.

Model 36-444 10” Contractor’s Saw® . Includes basic machine with two table extension wings, stand, belt and pulley guard, see-thru blade guard with splitter and anti-kickback attachment, miter gage, UniRip fence with front and rear guide bars, 10” saw blade, V-belt, arbor and motor pulleys plus 11⁄2 HP, 115/230V, single phase motor.

Model 36-445 10” Contractor’s Saw® with 30” Unifence® Saw Guide. Same as model 36-444 but with one table extension wing and 30” Unifence® Saw Guide which includes front and rear guide bars, table support legs and mounting hardware. Less table board.

Model 36-440 10” Contractor’s Saw® with 29” Precision Saw Guide. Same as model 36-444 but with one table wing extension and 29” Precision Saw Guide which includes fence, carriage assembly, front guide rail, table frame and mounting hardware. Less table board and legs.

Model 36-450 10” Contractor’s Saw® with 50” Precision Saw Guide. Same as model 36-444,

but with one table extension wing and 50” Precision Saw Guide which includes fence, carriage assembly, front guide rail, table frame, table support legs and mounting hardware. Less table board.

®

Model 36-444

10” Contractor’s Saw®

Model 36-440 10” Contractor’s Saw® with

29” Precision Saw Guide

6	For accessories, see page 27

10” Contractor’s Saw®

Model 36-460 10” Contractor’s Saw® with 28” Biesemeyer T-Square® Home Shop Saw Fence System. Same as model 36-444, but with one table extension wing and 28” Biesemeyer T-Square® Home Shop Saw Fence System which includes T-Square fence, front and rear rails, guide tube and mounting hardware. Less table board and legs.

Model 36-470 10” Contractor’s Saw® with 40” Biesemeyer T-Square® Home Shop Saw Fence System. Same as model 36-444, but with one table extension wing and 40” Biesemeyer T-Square® Home Shop Saw Fence System which includes T-Square fence, front and rear rails, table support legs, guide tube and mounting hardware. Less table board.

Model 36-480 10” Contractor’s Saw® with 52” Biesemeyer T-Square® Home Shop Saw Fence System. Same as model 36-444, but with one table extension wing and 52” Biesemeyer T-Square® Home Shop Saw Fence System which includes T-Square fence, front and rear rails, table support legs, guide tube and mounting hardware. Less table board.

Model 36-490 10” Contractor’s Saw’ with 30” Biesemeyer T-Square® Commercial Saw Fence System. Same as model 36-444, but with one table extension wing and 30” Biesemeyer T-Square® Commercial Saw Fence System which includes T-Square fence, front and rear rails, guide tube and mounting hardware. Less table board and legs.

Model 36-490

10” Contractor’s Saw® with 30” Biesemeyer T-Square® Commercial Saw Fence System

Model 36-480

10” Contractor’s Saw® with 52” Biesemeyer T-Square® Home Shop Saw Fence System

Motor ...................	11⁄2 HP,115/230V, 60 Hz.,
		single phase
Blade:
Diameter.................................		10” (254 mm)
Arbor..........................................		5⁄8” (16 mm)
Speed ...........................................		3000 rpm
Capacities:
Max. depth of cut ....................		31⁄8” (79 mm)
Max. depth of cut at 45° .........		21⁄8” (54 mm)
Max. rip to right of blade for:
Model 36-444 ....................		30” (762 mm)
Model 36-445 ....................		30” (762 mm)
Model 36-440 ....................		29” (737 mm)
Model 36-450 ..................		50” (1270 mm)
Model 36-460 ....................		28” (711 mm)
Model 36-470 ..................		40” (1016 mm)
Model 36-480 ..................		52” (1321 mm)
Model 36-490 ....................		30” (762 mm)
Max. rip to left of blade for:
Model 36-444 .................		131⁄2” (343 mm)
Model 36-445 ...................		83⁄4” (222 mm)
Models 36-440, 36-450, 36-460, 36-470,
36-480 and 36-490 ........		12” (305 mm)
Table in front of saw at
max. depth of cut ..........		121⁄4” (311 mm)
Max. width of dado	.................	13⁄16” (21 mm)

SPECIFICATIONS

	Table:			Overall Dimensions:
	Size ...................	20” x 27” (508 x 686 mm)		Height (on steel stand) ...........	39” (991 mm)
	Size with extension wings		............ 40” x 27”	Width with wings and guide bar		..............57”
			(1016 x 686 mm)			(1448 mm)
	Size with extension wing and:			Width with wing and:
	Unifence table board ................		62” x 27”	Model 36-445 ..................	62” (1575 mm)
			(1575 x 686 mm)	Model 36-440 ..................	59” (1499 mm)
	29” Precision Saw Guide table			Model 36-450 ..................	80” (2032 mm)
	board ..........	54” x 27” (1372 x 686 mm)		Model 36-460 ..................	58” (1473 mm)
	50” Precision Saw Guide table			Model 36-470 ..................	70” (1778 mm)
	board ........	78” x 27” (1981 x 686 mm)		Model 36-480 ..................	82” (2083 mm)
	28” Biesemeyer T-Square Home Shop			Model 36-490 ..................	60” (1524 mm)
	Saw Fence System ..................		52” x 27”	Depth Model 36-444	42” (1067 mm)
			(1321 x 686 mm)
				Models 36-445, 36-440
	40” Biesemeyer T-Square Home Shop
				and 36-450	43” (1092 mm)
	Fence System		64” x 27”
		..........................		Models 36-460, 36-470
			(1626 x 686 mm)
				and 36-480	36” (914 mm)
	52” Biesemeyer T-Square Home Shop
				Model 36-490	42” (1067 mm)
	Fence System		76” x 27”
		..........................		Weight:
			(1930 x 686 mm)
				Model 36-444	220 lbs. (99 kg)
	30” Biesemeyer T-Square Commercial
				Model 36-445	248 lbs. (112 kg)
	Saw Fence System		54” x 27”
				Model 36-440	245 lbs. (111 kg)
			(1372 x 686 mm)
				Model 36-450	266 lbs. (120 kg)
	Miter gage groove ..........................		3⁄8” x 3⁄4”
			(10 x 19 mm)	Model 36-460 ................	267 lbs. (121 kg)
				Model 36-470	275 lbs. (125 kg)
	Height on steel stand .........		34 1 ⁄ 4 ” (185 mm)
				Model 36-480 ................	282 lbs. (128 kg)
				Model 36-490 ................	286 lbs. (130 kg)

7	For additional accessories, see page 28

10” Contractor’s Saw® II

Solid construction and quality features make this saw one smooth operator.

•Powerful 11⁄2 HP, single phase induction motor provides the power to handle any cutting operation.

•Auto-Set® T-Slot miter gage has adjustable stops at 45° and 90° for precision straight and angle cutting jobs.

•Rack and worm gear blade elevating mechanism raises and lowers blade smoothly and easily.

•See-through blade guard with splitter and antikickback fingers promotes operator safety.

•Accessory dust collector connector mounts to saw carriage for attaching a dust collection system right at the source of dust and chips.

•Large on/off paddle switch.

Model 36-630 10” Contractor’s Saw® Il. Includes basic machine with 11⁄2 HP, single phase motor, blade guard, splitter and anti-kickback fingers, Jet-Lock® rip fence, guide bars, Auto-Set® miter gage, 10” saw blade, table insert, arbor pulley, motor pulley, V-belt, two extension wings, steel leg stand and instruction manual.

Model 36-640 10” Contractor’s Saw® Il with Precision Saw Guide. Same as above less Jet-Lock® rip fence with front and rear guide bars and one table extension wing, but with 29” Precision Saw Guide, carriage assembly, front guide rail, table frame, mounting hardware and

instruction manual. Less table board.

®

Model 36-630

10” Contractor's Saw® II

Cast iron 20” x 27” table with T-slotted miter gage grooves and two extension wings.

Self-aligning Jet-Lock® Micro-Set® rip fence glides on chrome-plated rails.

Model 36-640 10” Contractor’s Saw II with 29” Precision Saw Guide

SPECIFICATIONS

Motor .................................	11⁄2 HP, 115/230V, single phase, 60 Hz.
Blade:
Diameter ....................................................................		10” (254 mm)
Arbor .............................................................................		5⁄8” (16 mm)
Speed ...............................................................................		3000 rpm
Capacity:		31⁄8” (79 mm)
Maximum depth of cut at 90° .....................................
Maximum depth of cut at 45° .....................................		21⁄8” (54 mm)
Maximum rip to right of blade:
Model 36-630 .......................................................		24” (610 mm)
Model 36-640 .......................................................		29” (737 mm)
Maximum rip to left of blade	...................................	121⁄4” (311 mm)
Table in front of saw blade at max. cut ...................		121⁄4” (311 mm)
Maximum width of dado .............................................		13⁄16” (21 mm)

Table:
Size ........................................................	20” x 27” (508 x 686 mm)
Size with extension wings ....................	40” x 27” (1016 x 686 mm)
Height .....................................................................	351⁄2” (902 mm)
T-slotted miter gage grooves .......................	3⁄8” x 3⁄4” (10 x 19 mm)
Overall Dimensions:
Length:
Model 36-630 .....................................................	44” (1118 mm)
Model 36-640 .....................................................	42” (1067 mm)
Width:
Model 36-630 .....................................................	48” (1219 mm)
Model 36-640 .....................................................	59” (1499 mm)
Height:
Model 36-630 .....................................................	40” (1016 mm)
Model 36-640 ..................................................	401⁄2” (1029 mm)
Weight:
Model 36-630 .....................................................	188 lbs. (85 kg)
Model 36-640 .....................................................	202 lbs. (92 kg)

8	For accessories, see page 27

10” Table Saw

The home shop saw that combines power with precision T-square® accuracy.

•

•

Powerful 15 amp. motor provides 5500 rpm blade speed.

Full 221⁄4” x 383⁄8” table with extension wings provides ample work support for ripping large panels.

•Maximum 31⁄8” depth of cut at 90°, 21⁄8” at 45° blade tilt. Rips to the center of a 4’ panel.

•

•

•

•

T-Square® Fence System for precision accuracy.

See-thru blade guard with anti-kickback fingers.

Miter gage with 45° R&L and 90° stops for accurate angle cutting.

T-slot miter gage grooves hold miter gage beyond table.

Model 36-600 10” Table Saw. Includes
basic machine with 15 amp., 115V, sin-	®
gle phase motor, stand, miter gage, T-
Square rip fence, table insert,
see-thru blade guard with splitter
and anti-kickback fingers,
10” carbide-tipped saw blade,
wrench and instruction manual.

Full 221⁄4” x 383⁄8” table with extension wings and T-slot grooves provides ample work support for ripping large panels.

Miter gage has positive stops at 45° and 90° for accurate angle cutting. Compound angles can be achieved by tilting blade.

Saw can be converted for moulding operations with accessory cutterhead and table insert.

Cut dados in any width up to

13⁄16” simply by mounting accessory dado and table insert.

SPECIFICATIONS

Motor ...........................................................	15 amp., 115V, 60 Hz.
Blade:	5⁄8” (16 mm)
Diameter of Arbor .........................................................
Speed ...............................................................................	5500 rpm
Diameter of Blade ......................................................	10” (254 mm)
Capacity:	31⁄8” (79 mm)
Max. depth of cut at 90° .............................................
Max. depth of cut at 45° .............................................	21⁄8” (54 mm)
Table distance in front of blade at	113⁄4” (298 mm)
1” depth of cut ......................................................
Max. width of dado .....................................................	13⁄16” (21 mm)
Max. rip to right of blade ............................................	27” (686 mm)

Table:	221⁄4” x 203⁄8” (565 x 518 mm)
Size ..................................................
Size with both extension wings .................................	221⁄4” x 383⁄8”
	(565 x 975 mm)
Height on stand ......................................................	34 7⁄8” (886 mm)
Miter gage groove ........................................	3⁄8” x 3⁄4” (10 x 19 mm)
Overall Dimensions:
Height ......................................................................	40” (1016 mm)
Width .......................................................................	51” (1295 mm)
Depth ......................................................................	351⁄2” (902 mm)
Weight ....................................................................	145 Ibs. (66 kg)

9	For accessories, see page 27

Sidekick® 81⁄4” Builder’s Saw®

The Builder’s Saw that’s got it all.

•Cuts 21⁄4” at 90°; 15⁄8” at 45° blade tilt—enough capacity to cut dimensional 2 x 4 lumber.

•Diecast aluminum table, with integral outfeed work support and T-slot miter gage grooves, measures a full 26” x 20”.

•Miter gage with adjustable positive stops at 90° and 45° R&L for accurate straight and angle cutting.

•Self-aligning rip fence with single control handle and easy-to-read English/Metric rip scale.

•Carbide-tipped 81⁄4” dia. x 18 ATB saw blade included as standard equipment.

•Built-in holders and compartments for miter gage, cord, rip fence, blade guard, extra blade and wrench set storage.

Model 36-275 Sidekick® 81⁄4” Builder’s Saw® . Includes basic machine with

15 amp., 120V, 60 Hz. motor; rip fence, miter gage, see-through blade guard with splitter and anti-kickback fingers, carbidetipped 81⁄4” dia. x 18 ATB saw blade, table insert, wrenches and instruction manual.

®

Model 36-275

Sidekick® 81⁄4” Builder’s

Saw®

Integral outfeed work support handles large panels and long stock; slides in, out of the way, when not in use.

T-slot grooves hold miter gage securely beyond front of table, preventing it from falling during wide cut-off operations.

Built-in holders and compartments for out-of-the-way miter gage, rip fence, blade guard, extra blade and wrench set storage; easier accessibility when needed.

Convenient carrying handle and cord holder bracket for safe and easy transport from job to job.

SPECIFICATIONS

Motor .....................................	15 amp., 120V, single phase, 60 Hz.
Blade:		81⁄4” (210 mm)
Diameter ...................................................................
Arbor .............................................................................		5⁄8” (16 mm)
Speed ...............................................................................		4500 rpm
Capacity:		21⁄4” (57 mm)
Maximum depth of cut at 90° .....................................
Maximum depth of cut at 45° .....................................		15⁄8” (41 mm)
Maximum rip to right of blade ....................................		12” (305 mm)
Table in front of blade at 1” depth of cut		..................... 8” (203 mm)
Maximum width of dado .............................................		13⁄16” (21 mm)

Table:
Size ........................................................	26” x 20” (660 x 508 mm)
with accessory extension wing ............	32” x 20” (813 x 508 mm)
Height .....................................................................	121⁄8” (308 mm)
T-slot ............................................................	3⁄8” x 3⁄4” (10 x 19 mm)
Overall Dimensions:	157⁄8” (403 mm)
Height .....................................................................
Width .........................................................................	26” (660 mm)
Depth ......................................................................	253⁄8” (645 mm)
Weight ...................................................................	481⁄2 Ibs. (22 kg)

10	For accessories, see page 29

10” Bench Saw

Big saw capacity in an economical package.

•Lightweight for portability; goes where you go, when you need it.

•Ample capacity to cut 3” at 90°; 21⁄2” at 45°.

•Powered by a heavy duty 13 amp., 115V motor for dependability.

•Rip fence locks front and rear to maintain accuracy at the cut.

•Blade tilting and height control knobs are up-front for convenience.

•Self-aligning rip fence aligns and locks itself parallel to blade with single control lever.

•Big 171⁄4” x 26” table provides ample support for large ripping operations.

•Removable on-off switch to prevent unauthorized use.

•Convenient holder for out-of-the-way miter gage storage.

•See-thru blade guard with integral splitter and anti-kickback fingers for oper-

ator safety.	®	Model 36-540
Model 36-540 Type 2 10” Bench Saw. Includes		10” Bench Saw
basic machine with 13 amp., 115V, 60 Hz. motor;
rip fence, miter gage, see-thru blade guard with
splitter and anti-kickback fingers, 10” carbide-
tipped saw blade, standard table insert, blade
wrenches and instruction manual.

Cuts stock 3” thick at 90°, offers full 21⁄2” cutting capacity at 45° blade tilt.

T-slot table groove prevents miter gage	Model 36-545 10” Bench Saw
from falling during wide cut-off operations.	with Stand. Same as above, but with
	steel stand.

SPECIFICATIONS

Motor .......................................	13 amp., 115V, single phase, 60 Hz.
Blade:
Diameter ......................................................................	10” (254 mm)
Arbor .............................................................................	5⁄8” (16 mm)
Speed .................................................................................	4700 rpm
Capacity:
Max. depth of cut at 90° .................................................	3” (76 mm)
Max. depth of cut at 45° ...............................................	21⁄2” (64 mm)
Max. rip to right of blade.............................................	97⁄8” (252 mm)
Max. width of cut-off at 1” depth of cut
with T-slot miter gage................................................	10” (254 mm)
Max. width of dado .........................................................	1⁄2” (13 mm)

Table:	171⁄4” x 26” (438 x 660 mm)
Size.......................................................
T-slot ...............................................................	3⁄16” x 5⁄8” (5 x 16 mm)
Overall Dimensions:
Model 36-540 ...........	15”H x 26”W x 24”D (381 x 660 x 610 mm)
Model 36-545 ...........	39”H x 26”W x 24”D (991 x 660 x 610 mm)
Weight:
Model 36-540........................................................	40 Ibs. (18 kg)
Model 36-545........................................................	51 Ibs. (23 kg)

11	For accessories, see page 29

Sidekick® Saw Stand

Adds sturdy support and complete job-site mobility.

•Holds Delta 81⁄4” and 10” Bench Saws as well as most other competitive models.

•Storage slots hold rip fence out of the way when not in use.

•Two-year limited warranty.

Model 50-170 Sidekick® Saw Stand.

Includes stand, folding legs, fence guide rail, 13” diameter wheels, hardware and instruction manual.

Model 50-170 Sidekick® Saw Stand.

Sidekick 81⁄4” Builder’s Saw not included.

Precision fence and guide rail included for ripping operations to the right and left of saw blade.

Folds flat for storing or transporting from job to job.

The Sidekick Saw Stand helps		Large 13” diameter wheels
you move your bench saw quickly		for quick, easy movement —
and easily.		even up steps.

	SPECIFICATIONS			ACCESSORIES
Overall Dimensions:				No. 50-171 Rear Outfeed Work Support. Provides an additional
Length .......................................................................		73” (1854 mm)		12” of stock support.
Width ...........................................................................		27” (686 mm)
Height ......................................................................		351⁄2” (902 mm)
Opening Size: .....................................	221⁄4” x 23” (565 x 584 mm)
Weight: (without saw)	..............................................	65 lbs. (29 kg)
Rip Capacity (to right of blade):
With Model 36-275 Sidekick 81⁄4” Builder’s Saw ........		27” (686 mm)
Note: Rip capacity may vary according to your bench saw model.

12

Deluxe Sawbuck® Frame and Trim Saw

Try it once and you won’t be able to get along without it.

•Perfect for crosscuts up to 16” at 90°, 12” at 45° on hard and soft woods, vinyl and aluminum siding.

•Saw head miters and tilts for angle and compound cutting operations.

•Large 2913⁄16” miter scale has 1⁄4” between degree markings for easy reading with positive stops at 0°, 221⁄2° and 45° R and L including a special 31.62° position for cutting crown mouldings.

•Exclusive SMC construction eliminates table rust and corrosion; steel guide bars are Nitrotec™ treated for rust-free, smooth gliding operation.

•Powerful 15 amp. gear driven motor features an electric brake that automatically stops blade in seconds after the switch trigger is released.

Model 33-055 Deluxe Sawbuck® Frame and Trim Saw. Includes basic machine with 15 amp., 115V, 25-60 Hz., AC motor with electric automatic brake, 6 foot cord, leg set, blade guard with retractable leaf guard, 8” diameter crosscut saw blade, blade wrench and instruction manual.

Model 33-055

Deluxe Sawbuck®

Frame and Trim Saw

Table is made of an entirely new reinforced polyester resin		Set-up is simple and fast.
compound that prevents warping, springing and rusting. Cutting		Table rotates with track arm for
head is supported at both ends by corrosion-proof steel guide rails.		mitering. Motor tilts around
		common table-level pivot point
		for beveling.

Special 31.62° miter stop and 33.85° bevel setting facilitates compound cutting standard 52°/38° crown moulding.

Deluxe Sawbuck accommodates accessory 6” diameter stackable type dado head to cut grooves up to 13⁄16” wide.

SPECIFICATIONS

Motor ...............................................	15 amp., 115V, 25-60 Hz., AC
Brake ..................................................................	Electric, automatic
Blade:
Diameter ......................................................................	8” (203 mm)
Arbor .............................................................................	5⁄8” (16 mm)
Speed ...............................................................................	5500 rpm
Capacity:
Cut-Off at 90° ............................................................	16” (406 mm)
Cut-Off at 45° ............................................................	12” (305 mm)
Depth of cut at 90° .....................................................	23⁄4” (70 mm)
Depth of cut at 45° .....................................................	13⁄4” (44 mm)
Dado .......................................................	13⁄16” (21 mm) Width using
	6” Diameter Stackable Type

Cutting Head Height Adj. ................................	11⁄4” (32 mm) max.
Table:	281⁄2” (724 mm)
Diameter of cutting surface ....................................
Extension on both sides of table ............................	113⁄4” (298 mm)
Overall length ..........................................................	52” (1321 mm)
Height .....................................................................	351⁄4” (895 mm)
Fences ..............................................	23” (584 mm) R & L of Blade
Positive Stops:	0°, 221⁄2°, 31.62° & 45° R & L
Miter ...............................................
Overall Dimensions ...........................................	37” x 671⁄2” x 47”
	(940 x 1715 x 1194 mm)
Weight ......................................................................	96 Ibs. (44 kg)

13	For accessories, see page 29