3M 7048 User Manual
3M recommended for sanding, grinding, sawing, sweeping and insulating
(Keep these instructions for reference)
This respirator helps protect against certain particles. Misuse may result in sickness or death. For proper use, see supervisor, orUser Instructions, or call 3M in U.S.A.,
Before use, the wearer must read and understand these User Instructions. Keep these instructions for reference.
Particles such as those from grinding, sanding, sweeping, sawing, bagging, or processing minerals, coal, iron ore, flour, metal, wood, pollen, and certain other substances. Liquid or
Do Not Use For
Gases and vapors, oil aerosols, asbestos, arsenic, cadmium, lead,
This respirator can help reduce inhalation exposures to certain airborne biological particles (e.g. mold, Bacillus anthracis, Mycobacterium tuberculosis, etc.) but cannot eliminate the risk of contracting infection, illness or disease. OSHA and other government agencies have not established safe exposure limits for these contaminants.
1.Failure to follow all instructions and limitations on the use of this respirator and/or failure to wear this respirator during all times of exposure can reduce respirator effectiveness and may result in sickness or death.
2.Before occupational use of this respirator, a written respiratory protection program must be implemented meeting all the requirements of OSHA 29 CFR 1910.134 such as training, fit testing, medical evaluation, and applicable OSHA substance specific standards. In Canada, CSA standard Z94.4 requirements must be met and/or requirements of the applicable jurisdiction, as appropriate.
3.The particles which can be dangerous to your health include those so small that you cannot see them.
4.Leave the contaminated area immediately and contact supervisor if dizziness, irritation, or other distress occurs.
5.Store the respirator away from contaminated areas when not in use.
6.Filtering facepieces are to be inspected prior to each use to assure there are no holes in the breathing zone other than the punctures around staples and no damage has occurred. Enlarged holes resulting from ripped or torn filter material around staple punctures are considered damage. Immediately replace respirator if damaged. Staple perforations do not affect NIOSH approval. (For 8110S only)
7. Dispose of used product in accordance with applicable regulations.
1.This respirator does not supply oxygen. Do not use in atmospheres containing less than 19.5% oxygen.
2.Do not use when concentrations of contaminants are immediately dangerous to life and health, are unknown or when concentrations exceed 10 times the permissible exposure limit (PEL) or according to specific OSHA standards or applicable government regulations, whichever is lower.
3.Do not alter, abuse or misuse this respirator.
4.Do not use with beards or other facial hair or other conditions that prevent a good seal between the face and the sealing surface of the respirator.
5.Respirators can help protect your lungs against certain airborne contaminants, however, they will not prevent entry through other routes such as the skin, which would require additional personal protective equipment (PPE).
6.This respirator is designed for occupational/professional use by adults who are properly trained in their use and limitations. Respirators are not designed to be used by children.
7.Individuals with a compromised respiratory system, such as asthma or emphysema, should consult a physician and complete a medical evaluation prior to use.
Time Use Limitation
If respirator becomes damaged, soiled, or breathing becomes difficult, leave the contaminated area immediately and replace the respirator.
Must be followed each time respirator is worn.
1.Prestretch top and bottom straps before placing respirator on the face (8210 only).
2.Cup the respirator in your hand, with the nosepiece at your fingertips, allowing the headbands to hang freely below your hand.
3.Position the respirator under your chin with the nosepiece up. Pull the top strap over your head resting it high at the top back of your head. Pull the bottom strap over your head and position it around the neck below the ears.
4.Place your fingertips from both hands at the top of the metal nosepiece. Using two hands, mold the nose area to the shape of your nose by pushing inward while moving your fingertips down both sides of the nosepiece.
! Pinching the nosepiece using one hand may result in improper fit and less effective respirator performance. Use two hands.
5.Perform a User Seal Check prior to each wearing. To check the
See step 3 of Fitting Instructions and cup respirator in hand to maintain position on face. Pull bottom strap over head. Still holding respirator in position, pull top strap over head and remove respirator.
NIOSH Approved: N95
At least 95% filtration efficiency against solid and liquid aerosols that do not contain oil.
This respirator contains no components made from natural rubber latex.
FOR MORE INFORMATION
In United States, contact:
For other 3M products:
Exported by/Exporté par/Exportado por: 3M Occupational Health and Environmental Safety Division
3M Center, Building
P.O. Box 33010
St. Paul, MN
Made in U.S.A.