3M 60440273377, 60440273567, 60440273427, 60440273609, 60440273419 User Manual

3M™ Abrasive Products, Cubitron™ II 967A Flap Discs 06/27/14

Safety Data Sheet

Copyright,2014,3M Company.

All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.

Document Group:	31-7032-1	Version Number:	1.05
Issue Date:	06/27/14	Supercedes Date:	02/17/14

SECTION 1: Identification

1.1. Product identifier

3M™ Abrasive Products, Cubitron™ II 967A Flap Discs

1.2. Recommended use and restrictions on use

Recommended use

Abrasive Product

1.3. Supplier’s details	3M
MANUFACTURER:
DIVISION:	Abrasive Systems Division
ADDRESS:	3M Center, St. Paul, MN 55144-1000, USA
Telephone:	1-888-3M HELPS (1-888-364-3577)

1.4. Emergency telephone number

1-800-364-3577 or [phone] (24 hours)

SECTION 2: Hazard identification

2.1. Hazard classification

Not classified as hazardous according to OSHA Hazard Communication Standard, 29 CFR 1910.1200.

2.2. Label elements Signal word

Not applicable.

Symbols

Not applicable.

Pictograms

Not applicable.

2.3. Hazards not otherwise classified

None.

46% of the mixture consists of ingredients of unknown acute oral toxicity.

SECTION 3: Composition/information on ingredients

__________________________________________________________________________________________

Page 1 of 10

3M™ Abrasive Products, Cubitron™ II 967A Flap Discs 06/27/14

Ingredient	C.A.S. No.	% by Wt
Ceramic Aluminum Oxide (non-fibrous)	1344-28-1	5	- 20
Inorganic Fluoride	14075-53-7	2	-	15
Inorganic Fluoride	15096-52-3	1	-	10
Filler	13983-17-0	2	-	15
Filler	7727-43-7	1	-	5
Titanium Dioxide	13463-67-7	0	- 0.8
Cured Resin	Mixture	10 - 35
Cloth Backing	Mixture	15 - 30
Fiberglass plate	Mixture	20 -		30

SECTION 4: First aid measures

4.1. Description of first aid measures

Inhalation:

Remove person to fresh air. If you feel unwell, get medical attention.

Skin Contact:

Wash with soap and water. If signs/symptoms develop, get medical attention.

Eye Contact:

Flush with large amounts of water. Remove contact lenses if easy to do. Continue rinsing. If signs/symptoms persist, get medical attention.

If Swallowed:

No need for first aid is anticipated.

4.2.Most important symptoms and effects, both acute and delayed

See Section 11.1. Information on toxicological effects.

4.3.Indication of any immediate medical attention and special treatment required

Not applicable.

SECTION 5: Fire-fighting measures

5.1. Suitable extinguishing media

In case of fire: Use a fire fighting agent suitable for ordinary combustible material such as water or foam to extinguish.

5.2. Special hazards arising from the substance or mixture

None inherent in this product.

Hazardous Decomposition or By-Products
Substance	Condition
Carbon monoxide	During Combustion
Carbon dioxide	During Combustion
Hydrogen Fluoride	During Combustion

5.3. Special protective actions for fire-fighters

When fire fighting conditions are severe and total thermal decomposition of the product is possible, wear full protective clothing, including helmet, self-contained, positive pressure or pressure demand breathing apparatus, bunker coat and pants, bands around arms, waist and legs, face mask, and protective covering for exposed areas of the head.

__________________________________________________________________________________________

Page 2 of 10

3M™ Abrasive Products, Cubitron™ II 967A Flap Discs 06/27/14

SECTION 6: Accidental release measures

6.1.Personal precautions, protective equipment and emergency procedures

Observe precautions from other sections.

6.2.Environmental precautions

Not applicable.

6.3. Methods and material for containment and cleaning up

Not applicable.

SECTION 7: Handling and storage

7.1. Precautions for safe handling

Do not breathe thermal decomposition products. Avoid breathing of dust created by sanding, grinding or machining. Damaged product can break apart during use and cause serious injury to face or eyes. Check product for damage such as cracks or nicks prior to use. Replace if damaged. Always wear eye and face protection when working at sanding or grinding operations or when near such operations. Combustible dust may form by action of this product on another material (substrate). Dust generated from the substrate during use of this product may be explosive if in sufficient concentration with an ignition source. Dust deposits should not be allowed to accumulate on surfaces because of the potential for secondary explosions.

7.2. Conditions for safe storage including any incompatibilities

No special storage requirements.

SECTION 8: Exposure controls/personal protection

8.1. Control parameters Occupational exposure limits

Ingredient	C.A.S. No.	Agency	Limit type	Additional Comments
Aluminum, insoluble compounds	1344-28-1	ACGIH	TWA(respirable fraction):1
			mg/m3
Ceramic Aluminum Oxide (non-	1344-28-1	CMRG	TWA:1 fiber/cc
fibrous)
Ceramic Aluminum Oxide (non-	1344-28-1	OSHA	TWA(as total dust):15
fibrous)			mg/m3;TWA(respirable
			fraction):5 mg/m3
Titanium Dioxide	13463-67-7	ACGIH	TWA:10 mg/m3
Titanium Dioxide	13463-67-7	CMRG	TWA(as respirable dust):5
			mg/m3
Titanium Dioxide	13463-67-7	OSHA	TWA(as total dust):15 mg/m3
Aluminum, insoluble compounds	15096-52-3	ACGIH	TWA(respirable fraction):1
			mg/m3
FLUORIDES	15096-52-3	ACGIH	TWA(as F):2.5 mg/m3
FLUORIDES	15096-52-3	OSHA	TWA(as dust):2.5
			mg/m3;TWA(as F):2.5 mg/m3
Filler	7727-43-7	ACGIH	TWA(inhalable fraction):5
			mg/m3
Filler	7727-43-7	OSHA	TWA(as total dust):15
			mg/m3;TWA(respirable
			fraction):5 mg/m3

__________________________________________________________________________________________

Page 3 of 10