Yamaha HTR-5590 User Manual

U

HTR-5590

AV Receiver

OWNER’S MANUAL

IMPORTANT

Please record the serial number of this unit in the space below.

MODEL:

Serial No.:

The serial number is located on the rear of the unit. Retain this Owner’s Manual in a safe place for future reference.

IMPORTANT SAFETY INSTRUCTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

•Explanation of Graphical Symbols

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

1Read Instructions – All the safety and operating instructions should be read before the product is operated.

2Retain Instructions – The safety and operating instructions should be retained for future reference.

3Heed Warnings – All warnings on the product and in the operating instructions should be adhered to.

4Follow Instructions – All operating and use instructions should be followed.

5Cleaning – Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

6Attachments – Do not use attachments not recommended by the product manufacturer as they may cause hazards.

7Water and Moisture – Do not use this product near water – for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.

8Accessories – Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.

9A product and cart combination should be moved with care. Quick stops, excessive

force, and uneven surfaces may cause the product and cart combination to overturn.

10Ventilation – Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

11Power Sources – This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.

12Grounding or Polarization – This product may be equipped with a polarized alternating current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

13Power-Cord Protection – Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

14Lightning – For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

15Power Lines – An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

16Overloading – Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

17Object and Liquid Entry – Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

18Servicing – Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

19Damage Requiring Service – Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a)When the power-supply cord or plug is damaged,

b)If liquid has been spilled, or objects have fallen into the product,

c)If the product has been exposed to rain or water,

I CAUTION

d)If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation,

e)If the product has been dropped or damaged in any way, and

f)When the product exhibits a distinct change in performance - this indicates a need for service.

20Replacement Parts – When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

21Safety Check – Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

22Wall or Ceiling Mounting – The unit should be mounted to a wall or ceiling only as recommended by the manufacturer.

23Heat – The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

IMPORTANTSAFETYINSTRUCTIONS

24Outdoor Antenna Grounding – If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

EXAMPLE OF ANTENNA GROUNDING

MAST	ANTENNA
	LEAD IN
	WIRE
GROUND
CLAMP
	ANTENNA
	DISCHARGE UNIT
	(NEC SECTION 810–20)
ELECTRIC
SERVICE
EQUIPMENT	GROUNDING CONDUCTORS
	(NEC SECTION 810–21)
	GROUND CLAMPS
	POWER SERVICE GROUNDING
	ELECTRODE SYSTEM
	(NEC ART 250. PART H)
NEC – NATIONAL ELECTRICAL CODE

FCC INFORMATION (for US customers)

1.IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

2.IMPORTANT : When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA.

3.NOTE : This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices.

Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by the interference.

Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA 90620.

The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.

CAUTION II

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

1To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2Install this sound system in a well ventilated, cool, dry, clean place — away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. Allow ventilation space of at

least 30 cm on the top, 20 cm on the left and right, and 20 cm on the back of this unit.

3Locate this unit away from other electrical appliances, motors, or transformers to avoid humming sounds.

4Do not expose this unit to sudden temperature changes from cold to hot, and do not locate this unit in a environment with high humidity (i.e. a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal injury.

5Avoid installing this unit where foreign object may fall onto this unit and/or this unit may be exposed to liquid dripping or splashing. On the top of this unit, do not place:

–Other components, as they may cause damage and/or discoloration on the surface of this unit.

–Burning objects (i.e. candles), as they may cause fire, damage to this unit, and/or personal injury.

–Containers with liquid in them, as they may fall and liquid may cause electrical shock to the user and/or damage to

this unit.

6Do not cover this unit with a newspaper, tablecloth, curtain, etc. in order not to obstruct heat radiation. If the temperature inside this unit rises, it may cause fire, damage to this unit,

and/or personal injury.

7Do not plug in this unit to a wall outlet until all connections

are complete.

8Do not operate this unit upside-down. It may overheat, possibly causing damage.

9Do not use force on switches, knobs and/or cords.

10When disconnecting the power cord from the wall outlet, grasp the plug; do not pull the cord.

11Do not clean this unit with chemical solvents; this might damage the finish. Use a clean, dry cloth.

12Only voltage specified on this unit must be used. Using this unit with a higher voltage than specified is dangerous and may cause fire, damage to this unit, and/or personal injury. YAMAHA will not be held responsible for any damage resulting from use of this unit with a voltage other than specified.

13To prevent damage by lightning, disconnect the power cord from the wall outlet during an electrical storm.

14Do not attempt to modify or fix this unit. Contact qualified YAMAHA service personnel when any service is needed. The cabinet should never be opened for any reasons.

15When not planning to use this unit for long periods of time (i.e. vacation), disconnect the AC power plug from the wall outlet.

16Be sure to read the “TROUBLESHOOTING” section on common operating errors before concluding that this unit is faulty.

17Before moving this unit, press STANDBY/ON to set this unit in the standby mode, and disconnect the AC power plug from the wall outlet.

18VOLTAGE SELECTOR (For China model only)

The VOLTAGE SELECTOR on the rear panel of this unit must be set for your local main voltage BEFORE plugging into the AC main supply.

Voltages are 220/240 V AC, 50 Hz.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

This unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this unit itself is turned off. This state is called the standby mode. In this state, this unit is designed to consume a very small quantity of power.

FOR CANADIAN CUSTOMERS

To prevent electric shock, match wide blade of plug to wide slot and fully insert.

This Class B digital apparatus complies with Canadian ICES-003.

We Want You Listening For A Lifetime

YAMAHA and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion – and, most importantly, without affecting your sensitive hearing.

Since hearing damage from loud sounds is often undetectable until it is too late, YAMAHA and the Electronic Industries Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels.

III CAUTION

INTRODUCTION

CONTENTS

INTRODUCTION
CONTENTS ............................................................	1
FEATURES .............................................................	2
GETTING STARTED ............................................	3
Checking the Package Contents ................................	3
Installing Batteries in the Remote Control ................	3
CONTROLS AND FUNCTIONS .........................	4
Front Panel ................................................................	4
Remote Control .........................................................	6
Using the Remote Control .........................................	7
Front Panel Display ...................................................	8
Rear Panel .................................................................	9
PREPARATION
SPEAKER SETUP ...............................................	10
Speakers to Be Used ................................................	10
Speaker Placement ..................................................	10
Connecting the Speakers .........................................	11
CONNECTIONS ..................................................	14
Before Connecting Components .............................	14
Connecting Video Components ...............................	14
Connecting Audio Components ..............................	17
Connecting the Antennas .........................................	19
Connecting to a Subwoofer .....................................	20
Connecting to the 6CH INPUT Jacks .....................	20
Connecting the Power Supply Cords ......................	21
Turning on the Power ..............................................	22
ON-SCREEN DISPLAY (OSD) ..........................	23
OSD Modes .............................................................	23
Selecting the OSD Mode .........................................	23
SPEAKER MODE SETTINGS ..........................	24
Summary of SPEAKER SET Items 1A through 1G ...	24
ADJUSTING THE SPEAKER OUTPUT
LEVELS ............................................................	25
Before You Begin ....................................................	25
Using the Test Tone (TEST DOLBY SUR.) ...........	25
BASIC OPERATION
BASIC PLAYBACK .............................................	27
Input Modes and Indications ...................................	29
Selecting a Sound Field Program ............................	30
Selecting PRO LOGIC, PRO LOGIC or Neo: 6 ...	31
DIGITAL SOUND FIELD PROCESSING
(DSP) .................................................................	34
Understanding Sound Fields ...................................	34
Hi-Fi DSP Programs ...............................................	34
CINEMA-DSP ........................................................	34
Straight Decode .......................................................	35
Sound Field Effect ...................................................	35
Features of DSP Programs ......................................	36
Table of Program Names for Each Input Format ....	38
TUNING ................................................................	39
Automatic and Manual Tuning ................................	39
Presetting Stations ...................................................	40
Tuning in to a Preset Station ...................................	42
Exchanging Preset Stations .....................................	42
BASIC RECORDING ..........................................	43

ADVANCED OPERATION
REMOTE CONTROL FEATURES ...................	44
Control Area ............................................................	44
Setting the Manufacturer Code ...............................	45
Learn Feature ..........................................................	47
Changing the Source Name in the Display
Window ...............................................................	48
Clearing Learned Functions, Renamed Source
Names, and Setup Manufacturer Codes ..............	49
Each Component Control Area ...............................	50
SET MENU ...........................................................	55
Adjusting the Items on the SET MENU .................	55
1 SPEAKER SET (speaker mode settings) ............	56
2 LOW FRQ TEST ................................................	59
3 L/R BALANCE (balance of the left and right
main speakers) .....................................................	60
4 HP TONE CTRL (headphone tone control) ........	60
5 CENTER GEQ (center graphic equalizer) ..........	60
6 INPUT RENAME ...............................................	61
7 I/O ASSIGNMENT .............................................	61
8 INPUT MODE (initial input mode) ....................	62
9 PARAM. INI (parameter initialization) ..............	63
10LFE LEVEL ........................................................	63
11D-RANGE (dynamic range) ...............................	63
12SP DELAY ..........................................................	64
13DISPLAY SET ....................................................	65
14MEMORY GUARD ............................................	65
156CH INPUT SET ................................................	65
ADJUSTING THE LEVEL OF THE EFFECT
SPEAKERS .......................................................	66
SLEEP TIMER .....................................................	67
Setting the Sleep Timer ...........................................	67
Canceling the Sleep Timer ......................................	67
ZONE 2 (For U.S.A., Canada and Australia
models) ..............................................................	68
Remote Control in Zone 2 .......................................	69
ADDITIONAL INFORMATION
SOUND FIELD PROGRAM PARAMETER
EDITING ..........................................................	70
What is a Sound Field? ...........................................	70
Sound Field Program Parameters ............................	70
Changing Parameter Settings ..................................	71
Resetting a Parameter to the Factory-set Value .......	71
DIGITAL SOUND FIELD PARAMETER
DESCRIPTIONS ..............................................	72
TROUBLESHOOTING .......................................	76
GLOSSARY ..........................................................	81
SPECIFICATIONS ..............................................	83

INTRODUCTION
PREPARATION
OPERATION	BASIC
OPERATION	ADVANCED
INFORMATION	ADDITIONAL

English

1

FEATURES

Built-in 6-Channel Power Amplifier

Minimum RMS Output Power (0.04% THD, 20 Hz – 20 kHz, 8Ω)

Main:	100 W + 100 W
Center:	100 W
Rear:	100 W + 100 W
Rear center:	100 W

Multi-Mode Digital Sound Field

Processing

Dolby Pro Logic/Dolby Pro Logic Decoder

Dolby Digital/Dolby Digital EX Decoder

DTS/DTS ES Matrix 6.1, Discrete 6.1, DTS Neo: 6 Decoder

CINEMA DSP: Combination of YAMAHA DSP Technology and Dolby Pro Logic, Dolby Digital or DTS

Virtual CINEMA DSP

SILENT CINEMA DSP

Sophisticated AM/FM Tuner

40-Station Random Access Preset Tuning

Automatic Preset Tuning

Preset Station Shifting Capability (Preset Editing)

Other Features

96-kHz/24-bit D/A Converter

“SET MENU” which Provides You with 15 Items for Optimizing This Unit for Your Audio/Video System

Test Tone Generator for Easier Speaker Balance Adjustment

6-Channel External Decoder Input for Other Future Formats

BASS EXTENSION Button for Reinforcing Bass Response

On Screen Display Function Helpful in Controlling This Unit

S Video Signal Input/Output Capability

Component Video Input/Output Capability

Video Conversion (S Video → Composite Video)

Optical and Coaxial Digital Audio Signal Jacks

Sleep Timer

Remote Control with Preset Manufacturer Codes and “Learning” Capability

PROCESSOR DIRECT for no alteration of the original signal

Custom Installation Facility (U.S.A., Canada and Australia models only)

•yindicates a tip for your operation.

•Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button

names differ between the main unit and the remote control, the button name on the remote control is given in parentheses in this manual.

•This manual is printed prior to production. Design and specifications are subject to change in part for the purpose of the improvement in operativity and others. In this case the product has priority.

Manufactured under license from Dolby Laboratories.
	“DTS”, “DTS-ES Extended Surround” and “Neo: 6” are
	trademarks of Digital Theater System, Inc.
“Dolby”, “Pro Logic”, and the double-D symbol are trademarks
of Dolby Laboratories.

2

GETTING STARTED

Checking the Package Contents

Check your package to make sure it has the following items.

Remote control

TRANSMIT		RE–NAME CLEAR	LEARN
SYSTEM	STANDBY		6CH INPUT
POWER		SLEEP
A	PHONO	TUNER	CD
V-AUX	CBL/SAT	MD/TAPE	CD-R
D-TV/LD	VCR 1	VCR2/DVR	DVD

			SELECT
POWER		POWER	AMP
TV		AV
REC
		AUDIO	+
DISC SKIP
			VOL
			–
LEVEL	+	SET MENU	MUTE
TITLE		MENU
TV INPUT	TV VOL	A/B/C/D/E
CH	TV MUTE	CH
–	SELECT	+
PRESET		PRESET
TEST	TV VOL	ON SCREEN	STEREO
RETURN	–	DISPLAY
			EFFECT
HALL	CHURCH	JAZZ CLUB	ROCK
			CONCERT
1	2	3	4
ENTER-	MUSIC	TV	MOVIE
TAINMENT	VIDEO	THEATER	THEATER 1
5	6	7	8
MOVIE	/DTS		EX/ES
THEATER 2	SUR.	SELECT
9	10	11	12
	0	+10	CHP/INDEX

Batteries (4)	AM loop antenna
(AAA, R03, UM-4)

Indoor FM antenna

(For U.S.A., Canada and (For Australia model) China models)

INTRODUCTION

Installing Batteries in the Remote Control

2 1

3

1 Press the part and slide the battery compartment cover off.

2 Insert four supplied batteries (AAA, R03, UM-

4) according to the polarity markings on the inside of the battery compartment.

3 Slide the cover back until it snaps into place.

■ Notes on batteries

•Change the batteries periodically.

•Do not use old batteries together with new ones.

•Do not use different types of batteries (such as alkaline and manganese batteries) together. Read the packaging carefully as these different types of batteries may have the same shape and color.

■ Changing batteries

As the batteries lose power, the operating range of the remote control decreases and the indicator does not flash or its light becomes dim. When you notice any of these conditions, change all of the batteries.

Notes

•If the batteries have leaked, dispose of them immediately. Avoid touching the leaked material or letting it come into contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries.

•If the remote control is without batteries for more than 2 minutes, or if exhausted batteries remain in the remote

control, the contents of the memory may be cleared. When the memory is cleared, insert new batteries, set up the manufacturer code and program any acquired functions that may have been cleared.

English

3

CONTROLS AND FUNCTIONS

Front Panel

1 2

3

4

5

6

7

VOLUME

NATURAL SOUND AV RECEIVER

D I G I T A L

STANDBY

/ON

6CH

INPUT

MODE

PRESET/

PRESET

TUNING

BASS

TREBLE

A/B/C/D/E

TUNING

/TUNING FM/AM MEMORY MODE

TUNER

SPEAKERS

BASS

PROCESSOR

EDIT

MAN'L/AUTO FM AUTO/MAN'L MONO

A

B

EXTENSION

DIRECT

PHONES

S VIDEO

VIDEO

L AUDIO R

OPTICAL

STEREO

PROGRAM

DSP

EFFECT

SILENT

VIDEO AUX

–

+

–

+

	PRESET	TUNING
	/TUNING FM/AM MEMORY MODE
	EDIT	MAN'L/AUTO FM AUTO/MAN'L MONO
8 9 0	q w e r t y u i o p a		s
1 STANDBY/ON	6 Front panel display

Turns on and sets this unit in the standby mode. When you turn on this unit, you will hear a click and there will be a 4 to 5-second delay before this unit can reproduce sound.

Standby mode

In this mode, this unit consumes a small amount of power to receive infrared-signals from the remote control.

2 6CH (INPUT)

Selects the source connected to the 6CH INPUT jacks. The source selected by pressing 6CH (INPUT) takes priority over the source selected with INPUT (or the input selector buttons on the remote control).

3 INPUT selector

Selects the input source you want to listen to or watch.

4 (INPUT) MODE

Shows information about the operational status of this unit.

7 VOLUME

Controls the output level of all audio channels. This does not affect the REC OUT level.

8 SPEAKERS A/B

Turn on or off the set of main speakers connected to the A and/or B terminals on the rear panel at each time its corresponding button is pressed.

9 BASS EXTENSION

Turns on or off the BASS EXTENSION function at each time the button is pressed, this feature boosts the bass frequency of the left and right main channels by +6 dB (60 Hz) while maintaining overall tonal balance. This boost is useful if you do not use a subwoofer.

0 PROCESSOR DIRECT

Sets the priority for the types of input signals (AUTO, DTS, ANALOG) to receive when one component is connected to two or more input jacks of this unit (see page 29). Priority cannot be set when 6CH INPUT is selected as the input source.

5 Remote control sensor

Receives signals from the remote control.

Turns on or off the PROCESSOR DIRECT function at each time the button is pressed. When this is on, BASS, TREBLE, and BASS EXTENSION are bypassed, eliminating any alteration of the original signal.

4

q STEREO/EFFECT

Switches the normal stereo or DSP effect reproduction. When STEREO is selected, 2-channel input signals are directed to the main left and right speakers without effect sounds. All Dolby Digital and DTS audio signals except for the LFE channel are mixed down to the main left and right speakers.

w A/B/C/D/E

Selects one of the 5 preset station groups (A to E).

e PROGRAM l / h

Selects the DSP program.

r PRESET/TUNING l / h

Selects preset station number 1 to 8 when the colon (:) appears next to the band indication on the front panel display, and selects the tuning frequency when the colon

(:) does not appear.

t PHONES jack

Outputs audio signals for private listening with headphones. When you connect headphones, no signals are output to the OUTPUT jacks or to the speakers. (There is an exception depending on the “1G SP B SET” setting on the SET MENU.)

y VIDEO AUX jacks

Inputs audio and video signals from a portable external source such as a game console. To reproduce source signals from these jacks, select V-AUX as the input source.

u PRESET/TUNING (EDIT)

Switches the function of PRESET/TUNING l/ h(the colon (:) turns on or off) between selecting a preset station number and tuning.

This button is also used to exchange the assignment of two preset stations with each other.

i FM/AM

Switches the reception band between FM and AM.

o MEMORY (MAN’L/AUTO FM)

Stores a station in the memory. Hold down this button for more than 3 seconds to start automatic preset tuning.

CONTROLS AND FUNCTIONS

p TUNING MODE (AUTO/MAN’L MONO)

Switches the tuning mode between automatic and manual. To select the automatic tuning mode, press this button so that the “AUTO” indicator lights up on the front panel display. To select the manual tuning mode, press this button so that the “AUTO” indicator does not light up.

a BASS

Adjusts the low-frequency response for the left and right main channels.

Turn the control to the right to increase or to the left to decrease the low-frequency response.

s TREBLE

Adjusts the high-frequency response for the left and right main channels.

Turn the control to the right to increase or to the left to decrease the high-frequency response.

Note

•If you increase or decrease the high-frequency or the lowfrequency sound to an extreme level, the tonal quality from the center and rear speakers may not match that of the left and right main speakers.

■ Opening and closing the front panel door

When you want to use the controls behind the front panel door, open the door by gently pressing on the lower part of the panel. When you are not using them, close the door.

NATURAL	SOUND
		AV RE
		CEIVER	HTR-5990

To open, press gently on the lower part of the panel.

INTRODUCTION

English

5

CONTROLS AND FUNCTIONS

Remote Control

This section describes the controls and their functions of the remote control to operate this unit. Functions written in yellow are to operate this unit. Make sure that the AMP mode is selected before operating this unit.

The functions written in green and white vary depending on the input source selected.

1					r
2	TRANSMIT		RE–NAME CLEAR LEARN		t
					y
3
	SYSTEM				u
	POWER	STANDBY	SLEEP	6CH INPUT
4
	A	PHONO	TUNER	CD	i

5

3 STANDBY

Sets this unit in the standby mode.

4 SYSTEM POWER

Turns on the power of this unit.

5A

Sets the remote control to operate other components (not necessarily connected to this unit) without changing this unit’s input source (see page 54).

6 Input selector buttons

Select the input source and change the control area (see “REMOTE CONTROL FEATURES” on pages 44 to 54).

7 Display window

	V-AUX	CBL/SAT	MD/TAPE	CD-R		Shows the selected source component that you are
6	D-TV/LD	VCR 1	VCR2/DVR	DVD		controlling.
						8 TV POWER
						Turns on and off the power of the TV.
7				SELECT	o	9 Operation Section
	POWER		POWER	AMP	p	Provides functions such as play, stop, skip, etc. for
8						operating your other components.
	TV		AV		a
	REC					0 LEVEL (TITLE)

9	AUDIO	+	s
DISC SKIP

VOL

–

0

q

w

LEVEL

TITLE

TV INPUT

CH

–

PRESET

TEST

RETURN

+	SET MENU	MUTE
	MENU
TV VOL	A/B/C/D/E
TV MUTE	CH
	+
SELECT
	PRESET
	ON SCREEN	STEREO

TV VOL

–DISPLAY

EFFECT

d f

g h

	HALL	CHURCH	JAZZ CLUB	ROCK
				CONCERT
	1	2	3	4
	ENTER-	MUSIC	TV	MOVIE
e	TAINMENT	VIDEO	THEATER	THEATER 1
	5	6	7	8
	MOVIE	/DTS		EX/ES
	THEATER 2	SUR.	SELECT
	9	10	11	12
		0	+10	CHP/INDEX

1 Infrared window

Outputs infrared control signals. Aim this window at the component you want to operate (see “Using the Remote Control” on page 7).

2 TRANSMIT indicator

Flashes while the remote control is sending signals.

Selects the effect speaker channel to be adjusted and sets the level.

q Cursor buttons u / d/ j / i

Selects and adjusts DSP program parameters and SET MENU items.

TV MUTE/SELECT button mutes your TV volume and selects menu items of your DVD player when their manufacture codes are set.

w TEST (RETURN)

Outputs the test tone to adjust the speaker levels.

e DSP program (Numeric) buttons

Select DSP programs.

r RE-NAME

Used for changing the input source name in the display window (see page 48).

t CLEAR

Used for clearing functions acquired when using the learn and rename features, and set manufacturer codes (see pages 48, 49).

y LEARN

Used for setting up the manufacturer code or for programming the functions of other remote controls (see pages 45-47).

u SLEEP

Sets the sleep timer.

i 6CH INPUT

Selects the source connected to the 6CH INPUT jacks.

6

o SELECT k/n

Selects the another component to control independently from the input that has been selected by pressing an input selector button.

p AV POWER

Turns on and off the power of the component selected by the input selector button.

a AMP

Selects AMP or other component selected by the input selector button.

s VOL +/–

Increases or decreases the volume level.

d MUTE

Mutes the sound. The MUTE indicator turns on when the MUTE function is on. Press again to restore the audio output to the previous volume level.

f SET MENU (MENU)

Selects the SET MENU mode.

g ON SCREEN (DISPLAY)

Displays the operation status of this unit and the parameter settings for DSP programs on the monitor (see page 23).

h STEREO/EFFECT

Switches the normal stereo or DSP effect reproduction. When STEREO is selected, 2-channel input signals are directed to the main left and right speakers without effect sounds. All Dolby Digital and DTS audio signals except for the LFE channel are also directed to the main left and right speakers.

CONTROLS AND FUNCTIONS

Using the Remote Control

	30°	30°	INTRODUCTION
			Approximately 6 m (20 feet)

The remote control transmits a directional infrared beam. Be sure to aim the remote control directly at the remote control sensor on the main unit during operation.

■ Handling the remote control

•Do not spill water or other liquids on the remote control.

•Do not drop the remote control.

•Do not leave or store the remote control in the following types of conditions:

–high humidity or temperature such as near a heater, stove or bath;

–dusty places; or

–in places subject to extremely low temperatures.

English

7

CONTROLS AND FUNCTIONS

Front Panel Display

1

2

3

4

5

6 78

9

V AUX

VCR2/DVR

VCR 1

CBL/SAT D TV/LD DVD MD/TAPE CD R

TUNER

CD

PHONO

MUTE

VOLUME

SLEEP

DSP

ES DISCRETE MATRIX

DTS Neo:6 DOLBY DIGITAL PRO LOGIC

STEREO

AUTO

BASS

MOVIE TV THEATER 12 ENTERTAINMENT

TUNED MEMORY

P. DIRECT

VIRTUAL

EX	DIGITAL				LFE
	SILENT			ft	L C	R
	PRO LOGIC/
PCM	SP			mS	RL RC	RR
	A B			dB
0	q w e	r	t y u i	o p a

1DSP indicator

Lights up when you select a digital sound field program.

2 Decoder indicators

When any of the decoders equipped on this unit functions, the indicator lights up.

3 VIRTUAL indicator

Lights up when using Virtual CINEMA DSP (see page 32).

4 Input source indicator

Shows the current input source with a cursor.

5 AUTO indicator

Shows that this unit is in the automatic tuning mode.

6 SLEEP indicator

Lights up while the sleep timer is on.

7 MUTE indicator

Flashes while the MUTE function is on.

8 BASS indicator

Lights up while BASS EXTENSION is on.

9 VOLUME level indicator

Indicates the volume level.

0 vindicator

Lights up when this unit is reproducing PCM (pulse code modulation) digital audio signals.

q SILENT indicator

Lights up when headphones are connected with the sound effect (see “SILENT CINEMA DSP” on page 32).

w SP A B indicator

Lights up according to which set of main speakers is selected. Both indicators light up when both sets of speakers are selected.

e Headphones indicator

Lights up when headphones are connected.

r DSP program indicators

The name of the selected DSP program lights up when the ENTERTAINMENT, MOVIE THEATER 1, MOVIE THEATER 2, TV THEATER or V/DTS SURROUND DSP program is selected.

t Multi-information display

Shows the current DSP program name and other information when adjusting or changing settings.

y STEREO indicator

Lights up when this unit is receiving a strong signal for an FM stereo broadcast while the “AUTO” indicator is lit.

u TUNED indicator

Lights up when this unit tunes in to a station.

i MEMORY indicator

Flashes to show a station can be stored.

o P. DIRECT

Lights up while PROCESSOR DIRECT is on.

p Input channel indicator

Indicates the channel components of input signals being received.

aLFE indicator

Lights up when the input signal contains the LFE signal.

8

CONTROLS AND FUNCTIONS

Rear Panel

1

2

3

*1

4

5

DIGITAL OUTPUT

AUDIO

AUDIO

VIDEO

COMPONENT VIDEO

REMOTE

CONTROL

OPTICAL

MD/TAPE

R

L

R

L

VIDEO

S VIDEO

PR/ CR

PB/ CB

Y

OUT

DVD

+12V

IN

DVD

IN

OUT

15mA MAX.

(PLAY)

CD-R

MD/TAPE

CBL

OUT

D-TV

/SAT

+

–

A

–

+

R

L

(REC)

/LD

CD

MONITOR

CBL

IN

OUT

(PLAY)

/SAT

CD-R

CD-R

OUTPUT

TUNER

+

–

MAIN

–

+

OUT

IN

(REC)

DVD

VCR 1

AM

ANT

SUB

CD

OUT

WOOFER

B

CBL

GND

REAR

/SAT

R

+

–

–

+

L

PHONO

IN

(SURROUND)

VCR 2

FM ANT

/DVR

CD

MAIN

OUT

75Ω

UNBAL.

SURROUND

+

–

–

+

D-TV

ZONE 2 OUT

/LD

COAXIAL

MONITOR OUT

REAR

CENTER

SPEAKERS

CENTER

SUB

DIGITAL

CENTER

WOOFER

VIDEO

S VIDEO

INPUT

GND

6CH INPUT

6

IMPEDANCE SELECTOR

SET BEFORE POWER ON

MAIN A OR B:		4ΩMIN. /SPEAKER
	A+B: 8ΩMIN. /SPEAKER
CENTER	:	6ΩMIN. /SPEAKER
REAR CENTER:		6ΩMIN. /SPEAKER
REAR	:	6ΩMIN. /SPEAKER
MAIN A OR B: 8ΩMIN. /SPEAKER
CENTER			: 8ΩMIN. /SPEAKER
REAR CENTER: 8ΩMIN. /SPEAKER
REAR			: 8ΩMIN. /SPEAKER

7

AC OUTLETS

INTRODUCTION

8 9 0

q w

1 DIGITAL OUTPUT jacks

2 Audio component jacks

See pages 17 and 18 for connection information.

3 Video component jacks

See pages 14 to 16 for connection information.

4 REMOTE IN/OUT jacks (U.S.A., Canada and Australia models only)

See page 69 details.

5 CONTROL OUT (U.S.A., Canada and Australia models only)

This is a control expansion terminal for commercial use.

6 AC power cord

Connect to a power outlet.

7 AC OUTLETS

Use these outlets to supply power to your other A/V components (see page 21).

8 DIGITAL INPUT jacks

9 6CH INPUT jacks

See page 20 for connection information.

0 ZONE 2 OUT jacks (U.S.A., Canada and Australia models only)

See page 68 for details.

er

(U.S.A. and Canada models)

q Antenna input terminals

See page 19 for connection information.

w SUBWOOFER jacks

See page 20 for connection information.

e Speaker terminals

See pages 11 and 12 for connection information.

r IMPEDANCE SELECTOR switch

Use this switch to match the amplifier output to your speaker impedance (see page 13). Set this unit in the standby mode before you change the setting of this switch.

< China model only >

FREQUENCY STEP switch

See page 19.

VOLTAGE SELECTOR

See page 21.

*1 As this terminal is used for an examination in the factory, do not connect any equipment to this terminal.

English

9

PREPARATION

SPEAKER SETUP

Speakers to Be Used

This unit has been designed to provide the best soundfield quality with a 6-speaker system, using left and right main speakers, left and right rear speakers, and a center and rear center speakers. If you use different brands of speakers (with different tonal qualities) in your system, the tone of a moving human voice and other types of sound may not shift smoothly. We recommend that you use speakers from the same manufacturer or speakers with the same tonal quality.

The main speakers are used for the main source sound plus the effect sounds. They will probably be the speakers from your present stereo system. The rear speakers are used for the effect and surround sounds, and the center speaker is for the center sounds (dialog, vocals, etc.). If for some reason it is not practical to use a center speaker, you can do without it. Best results, however, are obtained with the full system.

The main speakers should be high-performance models and have enough power-handling capacity to accept the maximum output of your audio system. The other speakers do not have to be equal to the main speakers. For precise sound localization, however, it is ideal to use the models of equivalent performance with the main speakers.

Speaker Placement

Refer to the following diagram when you place the speakers.

Center speaker	Main speaker (R)
	Rear speaker (R)
	Subwoofer
Main	1.8 m (6 feet)
speaker (L)
	Rear center
	speaker
	Rear speaker (L)

■ Main speakers

Place the left and right main speakers an equal distance from the ideal listening position. The distance of each speaker from each side of the video monitor should be the same.

■ Center speaker

Align the front face of the center speaker with the front face of your video monitor. Place the speaker as close to the monitor as possible, such as directly over or under the monitor and centrally between the main speakers.

■Use of a subwoofer expands your sound field

It is also possible to further expand your system with the addition of a subwoofer. The use of a subwoofer is effective not only for reinforcing bass frequencies from any or all channels, but also for reproducing the LFE (low-frequency effect) channel with high fidelity when the Dolby Digital signal or the DTS signal is played back. The YAMAHA Active Servo Processing Subwoofer System is ideal for natural and lively bass reproduction.

■ Rear speakers

Place these speakers behind your listening position, facing slightly inwards, nearly 1.8 m (6 feet) above the floor.

■ Rear center speaker

Place the rear center speaker in the center between the left and right rear speakers at the same height from the floor as the rear speakers.

■ Subwoofer

The position of the subwoofer is not so critical, because low bass sounds are not highly directional. But it is better to place the subwoofer near the main speakers. Turn it slightly toward the center of the room to reduce the wall reflections.

CAUTION

Use magnetically shielded speakers. If this type of speakers still creates the interference with a monitor, place the speakers away from the monitor.

Note

•If you do not use any effect speakers (rear, center and/or rear center), change the settings of SPEAKER SET items in the SET MENU to designate the signals to other terminals you connect speakers to.

10

SPEAKER SETUP

Connecting the Speakers

Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lack bass.

CAUTION

•Use speakers with the specified impedance shown on the rear panel of this unit.

•Do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit. This could damage this unit and/or speakers.

If necessary, use the SET MENU to change the speaker mode settings according to the number and size of the speakers in your configuration after you finish connecting your speakers.

■ Speaker cables

			A speaker cable is actually a pair of insulated cables
			running side by side. One of the cables is colored or
	10 mm (3/8”)		shaped differently, perhaps with a stripe, groove or ridge.
			1 Remove approximately 10 mm (3/8”) of
	1	2	insulation from each of the speaker cables.
			2 Twist the exposed wires of the cable
			together to prevent short circuits.
	■ Connecting to the SPEAKERS terminals
	Red: positive (+)	3	1 Unscrew the knob.
	Black: negative (–)		2 Insert one bare wire into the hole in the side
		2	of each terminal.
			3 Tighten the knob to secure the wire.
		1
		Banana plug	y
			(For U.S.A., Canada, Australia and China models)
			• Banana plug connections are also possible. First, tighten the
			knob and then insert the banana plug connector into the end of
			the corresponding terminal.

■ MAIN SPEAKERS terminals

One or two speaker systems can be connected to these terminals. If you use only one speaker system, connect it to either of the MAIN A or B terminals.

■ REAR SPEAKERS terminals

A rear speaker system can be connected to these terminals.

■ CENTER SPEAKER terminals

A center speaker can be connected to these terminals.

■ REAR CENTER SPEAKER terminals

A rear center speaker can be connected to these terminals.

PREPARATION

English

11

SPEAKER SETUP

	Subwoofer			Main A speaker		Main B speaker
				Right	Left	Right	Left
	system

1

2

3

DIGITAL OUTPUT

AUDIO

AUDIO

VIDEO

COMPONENT VIDEO

REMOTE

CONTROL

OPTICAL

MD/TAPE

R

L

R

L

VIDEO

S VIDEO

PR/ CR

PB/ CB

Y

OUT

+12V

IN

DVD

DVD

IN

OUT

15mA MAX.

(PLAY)

CD-R

MD/TAPE

CBL

OUT

D-TV

/SAT

+

–

–

+

R

A

L

(REC)

/LD

CD

MONITOR

IN

CBL

OUT

(PLAY)

/SAT

CD-R

CD-R

OUTPUT

+

–

MAIN

–

+

OUT

IN

TUNER

(REC)

DVD

VCR 1

AM

ANT

SUB

CD

OUT

WOOFER

B

CBL

GND

REAR

/SAT

R

+

–

–

+

L

PHONO

IN

(SURROUND)

VCR 2

FM ANT

/DVR

CD

MAIN

OUT

75Ω

UNBAL.

SURROUND

+

–

–

+

D-TV

ZONE 2 OUT

/LD

COAXIAL

MONITOR OUT

REAR

CENTER

SPEAKERS

CENTER

SUB

DIGITAL

CENTER

WOOFER

VIDEO

S VIDEO

INPUT

GND

6CH INPUT

IMPEDANCE SELECTOR

SET BEFORE POWER ON

MAIN A OR B:			4ΩMIN. /SPEAKER
	A+B: 8ΩMIN. /SPEAKER
CENTER	:		6ΩMIN. /SPEAKER
REAR CENTER:			6ΩMIN. /SPEAKER
REAR	:		6ΩMIN. /SPEAKER
MAIN A OR B: 8ΩMIN. /SPEAKER
CENTER			: 8ΩMIN. /SPEAKER
REAR CENTER: 8ΩMIN. /SPEAKER
REAR			: 8ΩMIN. /SPEAKER

AC OUTLETS

(U.S.A. and Canada models)

4	5	6		7
			Center
Right	Left		speaker	Rear Center
Rear speaker				speaker

6 2

1

3

4

7

5

The diagram above shows the speaker layout in the listening room.

■ SUBWOOFER jack

When using a subwoofer with built-in amplifier, including the YAMAHA Active Servo Processing Subwoofer System, connect the input jack of the subwoofer system to this jack. Low bass signals distributed from the main, center and/or rear channels are directed to this jack if they are assigned to this jack. (The cut-off frequency of this jack is 90 Hz.) The LFE (low-frequency effect) signals generated when Dolby Digital or DTS is decoded are also directed if they are assigned to this jack.

Note

•Depending on the settings of “1 SPEAKER SET” and “10 LFE LEVEL” on the SET MENU, some signals may not be output from the SUBWOOFER jack.

12

SPEAKER SETUP

■ IMPEDANCE SELECTOR switch

WARNING

Do not change the IMPEDANCE SELECTOR switch setting while the power of this unit is on, otherwise this unit may be damaged.

If this unit fails to turn on when STANDBY/ON (or SYSTEM POWER) is pressed, the IMPEDANCE SELECTOR switch may not be fully slid to either position. If so, slide the switch to either position fully when this unit is in the standby mode.

Select the left and right position according to the impedance of the speakers in your system. Be sure to move this switch only when this unit is in the standby mode.

IMPEDANCE SELECTOR switch

MAIN A OR B:			4ΩMIN. /SPEAKER
		A+B: 8ΩMIN. /SPEAKER
CENTER		:	6ΩMIN. /SPEAKER
REAR CENTER:			6ΩMIN. /SPEAKER
REAR		:	6ΩMIN. /SPEAKER
	MAIN A OR B: 8ΩMIN. /SPEAKER
	CENTER		: 8ΩMIN. /SPEAKER
	REAR CENTER: 8ΩMIN. /SPEAKER
	REAR		: 8ΩMIN. /SPEAKER

IMPEDANCE SELECTOR

SET BEFORE POWER ON

MAIN A OR B:

4ΩMIN. /SPEAKER

A+B: 8ΩMIN. /SPEAKER

CENTER

:

6ΩMIN. /SPEAKER

REAR CENTER:

6ΩMIN. /SPEAKER

REAR

:

6ΩMIN. /SPEAKER

MAIN A OR B: 8ΩMIN. /SPEAKER

CENTER

: 8ΩMIN. /SPEAKER

REAR CENTER: 8ΩMIN. /SPEAKER

REAR

: 8ΩMIN. /SPEAKER

(U.S.A. and Canada models)

Switch	Speaker	Impedance level
				PREPARATION
position		each speaker must be 8 Ω or higher.
		If you use one set of main speakers, the impedance of
	Main	each speaker must be 4 Ω or higher.
		If you use two sets of main speakers, the impedance of
Left	Center	The impedance must be 6 Ω or higher.
	Rear	The impedance must be 6 Ω or higher.
	Center
	Rear	The impedance of each speaker must be 6 Ω or higher.
	Main	If you use one set of main speakers, the impedance of
		each speaker must be 8 Ω or higher.
		If you use two sets of main speakers, the impedance of
		each speaker must be 16 Ω or higher.
		[U.S.A. and Canada models]
		The impedance of each speaker must be 8 Ω or higher.
Right
	Center	The impedance must be 8 Ω or higher.
	Rear	The impedance must be 8 Ω or higher.
	Center
	Rear	The impedance of each speaker must be 8 Ω or higher.

English

13

CONNECTIONS

Before Connecting Components

CAUTION

Never connect this unit and other components to mains power until all connections between components have been completed.

•Be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Some components require different connection methods and have different jack names. Refer to the operation instructions for each component to be connected to this unit.

•Use commercially available video pin cables when connecting to the S VIDEO and COMPONENT VIDEO jacks.

Connecting Video Components

■ About the video jacks

There are three types of video jacks.

VIDEO jack

VIDEO

VIDEO

S VIDEO jack

S VIDEO

VIDEO jacks transmit composite signals.

S VIDEO jacks transmit S-video signals. S-video signals are separated into luminance (Y) and color (C) video signals to achieve high-quality color reproduction.

COMPONENT VIDEO jacks

COMPONENT VIDEO	COMPONENT VIDEO jacks transmit
PR/ CR PB/ CB Y	component signals.
	Component signals are separated into
	luminance (Y) and color difference (PB /
	CB, PR/CR) to provide the best quality in
	picture reproduction.

Refer to the owner’s manuals for your monitor and other components being connected to reproduce these signals correctly.

You can connect an S-video output and component video output of your video components to this unit. Connect an S-video output to the S VIDEO jack and component video output to the COMPONENT VIDEO jack on this unit.

y

•The COMPONENT VIDEO jacks on this unit are independent of the S VIDEO and VIDEO jacks.

•Connection depends on the availability of input jacks on your monitor. The signals input through the S VIDEO jacks can be converted to composite signals inside of this unit and output through the VIDEO jacks on this unit as well.

•When signals input through both S VIDEO and VIDEO jacks, signals input through the S VIDEO jack has priority.

•You can designate the input for the COMPONENT VIDEO A and B jacks according to your component by using “7 I/O ASSIGNMENT” on the SET MENU (see pages 61 and 62 for details).

Note

•When you are using the COMPONENT VIDEO jacks, check the details in the owner’s manual that came with the component being connected.

■VIDEO AUX jacks (on the front panel)

These jacks are used to connect any video input source such as a game console and a camcorder to this unit.

S VIDEO

VIDEO

L AUDIO R OPTICAL

		VIDEO AUX
S	V	L	R	O

	OPTICAL OUT
	AUDIO OUT R
	AUDIO OUT L	Game
	VIDEO OUT	console or
		video camera
	S VIDEO OUT

14

CONNECTIONS

OPTICAL OUTPUT

DVD player

AUDIO OUTPUT

COMPONENT OUTPUT

VIDEO

S VIDEO

OUTPUT

OUTPUT

O

L

R

V

S

V

V

V

(U.S.A. and Canada

models)

DIGITAL OUTPUT

AUDIO

AUDIO

VIDEO

COMPONENT VIDEO

OPTICAL

MD/TAPE

R

L

R

L

VIDEO

S VIDEO

PR/ CR

PB/ CB

Y

DVD

IN

DVD

(PLAY)

CD-R

MD/TAPE

CBL

OUT

D-TV

/ SAT

+

–

R

(REC)

/LD

CD

MONITOR

CBL

IN

OUT

(PLAY)

/SAT

CD-R

CD-R

OUTPUT

+

–

OUT

IN

TUNER

(REC)

DVD

VCR 1

AM

ANT

SUB

CD

OUT

WOOFER

CBL

GND

/SAT

R

+

–

PHONO

IN

VCR 2

FM ANT

/DVR

CD

MAIN

OUT

75Ω

UNBAL.

SURROUND

+

–

D-TV

ZONE 2 OUT

/LD

COAXIAL

MONITOR OUT

CENTER

SUB

DIGITAL

CENTER

WOOFER

VIDEO

S VIDEO

INPUT

GND

6CH INPUT

PREPARATION

C

L

R

V

S

V

S

V

V

V

VIDEO	S VIDEO	VIDEO	S VIDEO
OUTPUT	OUTPUT
		INPUT	INPUT

AUDIO OUTPUT	TV/digital TV or	Video
	LD player	monitor
COAXIAL OUTPUT		COMPONENT
		INPUT

L

R

O

C

V

S

indicates signal direction

indicates left audio pin cables

indicates right audio pin cables indicates optical cables

indicates coaxial cables indicates video pin cables indicates S-video cables

V

V indicates component video cables

V

English

15

CONNECTIONS

OPTICAL OUTPUT

	Cable TV or
AUDIO OUTPUT	Satellite tuner	COMPONENT OUTPUT

			VIDEO OUTPUT
O	L	R	V

S VIDEO OUTPUT

S

V V V

DIGITAL OUTPUT		AUDIO			AUDIO	VIDEO		COMPONENT VIDEO
OPTICAL	MD/TAPE	R	L	R	L	VIDEO	S VIDEO	PR/ CR	PB/ CB	Y
								DVD
		IN
						DVD
		(PLAY)
	CD-R	MD/TAPE						CBL
		OUT				D-TV		/ SAT
		(REC)				/LD
	CD							MONITOR
						CBL
		IN						OUT
		(PLAY)				/SAT
	CD-R	CD-R
		OUT				IN			TUNER
		(REC)
	DVD					VCR 1			AM
		CD				OUT			ANT
	CBL								GND
	/SAT
		PHONO				IN
						VCR 2			FM ANT
						/DVR
	CD	MAIN				OUT			75Ω
								UNBAL.
		SURROUND
	D-TV					ZONE 2 OUT
	/LD
COAXIAL
					MONITOR OUT
			SUB
DIGITAL		CENTER	WOOFER			VIDEO	S VIDEO
INPUT	GND	6CH INPUT

(U.S.A. and Canada models)

L R

L R

V

V

S

S

V

S

V V V

	VIDEO	VIDEO	VIDEO	S VIDEO
	OUTPUT	INPUT
			INPUT	INPUT

	AUDIO INPUT	VCR 1 or VCR 2/	S VIDEO	Video
		DVR (digital
			OUTPUT	monitor
		video recorder)
				COMPONENT
	AUDIO OUTPUT		S VIDEO INPUT
				INPUT
	indicates signal direction			V

L

R

O

V

V	indicates component video cables
indicates left audio pin cables
V
indicates right audio pin cables
indicates optical cables
indicates video pin cables

S	indicates S-video cables

16

CONNECTIONS

Connecting Audio Components

■ Connecting to digital jacks

This unit has digital jacks for direct transmission of digital signals through either coaxial or fiber optic cables. You can use the digital jacks to input PCM, Dolby Digital and DTS bitstreams. When you connect components to both the COAXIAL and OPTICAL jacks, priority is given to the input signals from the COAXIAL jack. All digital input jacks are acceptable for 96-kHz sampling digital signals.

y

•You can designate the input for each digital jacks according to your component by using “7 I/O ASSIGNMENT” on the SET MENU (see pages 61 and 62 for details).

About the dust protection cap

Pull out the cap from the optical jack before you connect the fiber optic cable. Do not discard the cap. When you are not using the optical jack, be sure to put the cap back in place. This cap protects the jack from dust.

Notes

•DIGITAL OUTPUT jacks and analog OUT (REC) jacks are independent. Only digital signals are output from DIGITAL OUTPUT jacks and analog signals from OUT (REC) jacks.

•The OPTICAL jacks on this unit conform to the EIA standard. If you use a fiber optic cable that does not conform to this standard, this unit may not function properly.

■ Connecting a CD player

y

•The COAXIAL CD and OPTICAL CD jacks are available for a CD player which has coaxial or optical digital output jacks.

•When you connect a CD player to both the COAXIAL CD and OPTICAL CD jacks, priority is given to the input signals from the COAXIAL CD jack.

■Connecting an MD recorder, tape deck or CD recorder

y

•DIGITAL OUTPUT jacks and analog OUT(REC) are independent. Only digital signals are output from DIGITAL OUTPUT jacks and analog signals from OUT(REC) jacks.

•When you connect your recording component to both the analog and digital input and output jacks, the priority is given to the digital signal.

Notes

•When you connect a recording component to this unit, keep its power on while using this unit. If the power is off, this unit may distort the sound from other components.

•When you record from a source component connected to this unit while this unit is set in the standby mode, the recorded sound may be distorted. To avoid this problem, turn on this unit.

■ Connecting a turntable

PHONO jacks are for connecting a turntable with an MM or high-output MC cartridge. If you have a turntable with a low-output MC cartridge, use an in-line boosting transformer or MC-head amplifier when connecting to these jacks.

y

•Connect your turntable to the GND terminal to reduce noise in the signal. However you may hear less noise without the connection to the GND terminal for some record players.

PREPARATION

English

17

CONNECTIONS

	INPUT
OPTICAL INPUT MD recorder or
tape deck	OUTPUT

	O				L	R	L	R
								OPTICAL INPUT
	DIGITAL OUTPUT			AUDIO				CD recorder
	OPTICAL	MD/TAPE		R	L
			IN					OUTPUT
			(PLAY)
		CD-R	MD/TAPE
								INPUT
			OUT
	OPTICAL		(REC)
								O
	OUTPUT	CD
CD player								L	R	O
	O		IN
			(PLAY)					L
		CD-R	CD-R					R
			OUT
	OUTPUT		(REC)
		DVD
								OPTICAL OUTPUT
	L		CD
		CBL
	R	/SAT
			PHONO
	C	CD	MAIN
COAXIAL OUTPUT			SURROUND
		D-TV
		/LD
	COAXIAL
					SUB
	DIGITAL			CENTER	WOOFER
	INPUT	GND		6CH INPUT

(U.S.A. and Canada models)

L	R
GND
OUTPUT

Turntable

	indicates signal direction
L	indicates left audio pin cables
R	indicates right audio pin cables
O	indicates optical cables
C	indicates coaxial cables

L

R

L

R

SURROUND
OUTPUT	MAIN OUTPUT

SUBWOOFER External decoder
OUTPUT	See page 20
CENTER OUTPUT

18

CONNECTIONS

Connecting the Antennas

Both AM and FM indoor antennas are included with this unit. In general, these antennas should provide sufficient signal

strength.

Connect each antenna correctly to the designated terminals.

FREQUENCY STEP switch (For China model)

100kHz/10kHz

50kHz/9kHz

FM AM

FREQUENCY

STEP

Because the interstation frequency spacing differs in different areas, set the FREQUENCY STEP switch (locating on the rear panel) according to the frequency spacing in your area.

North, Central and South America: 100 kHz/10 kHz

Other area: 50 kHz/9 kHz

Before setting this switch, disconnect the AC power plug of this unit from the AC outlet.

AM loop antenna

(included) Indoor FM antenna (included)

■ Connecting the AM loop antenna

1 Set up the AM loop antenna, then connect it.

2 Press and hold the tab to insert the AM loop antenna lead wires into the AM ANT and GND terminals.

COMPONENT VIDEO

PR/ CR

PB/ CB

Y

VD

BL

AT

ITOR

UT

TUNER

AM

ANT

GND

FM ANT

75Ω

UNBAL.

3 Orient the AM loop antenna for the beat reception.

y

•The AM loop antenna can be removed from the stand and attached to a wall, etc.

Ground (GND terminal)

Notes

For maximum safety and minimum interference, connect the antenna GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth.

■Connecting the indoor FM antenna

Connect the included indoor FM antenna to the 75Ω UNBAL. FM ANT terminal.

•The AM loop antenna should be placed away from this unit.

•The AM loop antenna should always be connected, even if an outdoor AM antenna is connected to this unit.

A properly installed outdoor antenna provides clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may improve the quality. Consult the nearest authorized YAMAHA dealer or service center about the outdoor antennas.

PREPARATION

English

19

CONNECTIONS

Connecting to a Subwoofer

OUTPUT

SUB

WOOFER

SUBWOOFER jack

When using a subwoofer with built-in amplifier, including the YAMAHA Active Servo Processing Subwoofer System, connect the input jack of the subwoofer system to this jack. Low bass signals distributed from the main, center and/or rear channels are directed to this jack if they are assigned to this jack. (The cut-off frequency of this jack is 90 Hz.) The LFE (low-frequency effect) signals generated when Dolby Digital or DTS is decoded are also directed if they are assigned to this jack.

Notes

•Adjust the volume level of the subwoofer with the control on the subwoofer. It is also possible to adjust the volume level by using the remote control of this unit (see ADJUSTING THE LEVEL OF THE EFFECT SPEAKERS on page 66).

•Depending on the settings of “1 SPEAKER SET” and “10 LFE LEVEL” on the SET MENU, some signals may not be output from the SUBWOOFER jack.

Connecting to the 6CH INPUT

Jacks

This unit is equipped with 6 additional input jacks (left and right MAIN, CENTER, left and right SURROUND and SUBWOOFER) for discrete multi-channel input from an external decoder, sound processor or pre-amplifier.

Connect the output jacks on your external decoder to the 6CH INPUT jacks. Be sure to match the left and right outputs to the left and right input jacks for the main and surround channels.

Notes

•When 6CH INPUT is selected, the signals input to the 6CH INPUT jacks have priority over any other input source.

•When you select 6CH INPUT as the input source, this unit automatically turns off the digital sound field processor, and you cannot listen to DSP programs.

•When you select 6CH INPUT as the input source, settings of “1 SPEAKER SET (1A to 1E)” on the SET MENU do not apply.

•When headphones are used, only main L/R channels are output.

•Setting for “15 6CH INPUT SET” on the SET MENU will be applied when 6CH INPUT is selected.

20

CONNECTIONS

Connecting the Power Supply Cords

■ Connecting the AC power cord

Plug this unit into the wall outlet.

Plug in the other components connected to this unit to the wall outlet.

EDANCE SELECTOR

T BEFORE POWER ON

A OR B:		4ΩMIN. /SPEAKER
	A+B: 8ΩMIN. /SPEAKER
ER	:	6ΩMIN. /SPEAKER
CENTER: 6ΩMIN. /SPEAKER
	: 6ΩMIN. /SPEAKER
AIN A OR B: 8ΩMIN. /SPEAKER
ENTER		: 8ΩMIN. /SPEAKER
EAR CENTER: 8ΩMIN. /SPEAKER
EAR		: 8ΩMIN. /SPEAKER

AC OUTLETS

(U.S.A. and Canada models)

■ AC OUTLET(S) (SWITCHED)

U.S.A., Canada and China models ...............	2 OUTLETS
To AC outlet	1 OUTLET
Australia model ..............................................

Use these outlets to connect the power cords from your components to this unit. The power to the AC OUTLET(S) is controlled by this unit’s STANDBY/ON (or SYSTEM POWER and STANDBY). These outlets will supply power to any connected component whenever this unit is turned on. The maximum power (total power consumption of components) that can be connected to the

AC OUTLET(S) is:
U.S.A. and Canada models	...................................... 80 W
China model .............................................................	50 W
Australia model ......................................................	100 W

PREPARATION

VOLTAGE SELECTOR

PEDANCE SELECTOR

T BEFORE POWER ON

N A OR B: 4ΩMIN. /SPEAKER A+B: 8ΩMIN. /SPEAKER TER : 6ΩMIN. /SPEAKER R CENTER: 6ΩMIN. /SPEAKER

R: 6ΩMIN. /SPEAKER

MAIN A OR B:			8ΩMIN. /SPEAKER
		A+B: 16ΩMIN. /SPEAKER
CENTER		:	8ΩMIN. /SPEAKER
REAR CENTER:			8ΩMIN. /SPEAKER
REAR		:	8ΩMIN. /SPEAKER

VOLTAGE SELECTOR

AC OUTLETS

■ VOLTAGE SELECTOR

(China model only)

The VOLTAGE SELECTOR on the rear panel of this unit must be set for your local main voltage BEFORE plugging into the AC main supply. Voltages are 110/120/ 220/240 V AC, 50/60 Hz.

(China model)

English

21

CONNECTIONS

Turning on the Power

When all connections are completed, turn on the power of this unit.

	1
										VOLUME
		NATURAL SOUND AV RECEIVER
	STANDBY
	/ON
		6CH	INPUT	MODE
					PRESET/	PRESET		TUNING	BASS		TREBLE
				A/B/C/D/E	TUNING	/TUNING	FM/AM MEMORY	MODE
				TUNER
SPEAKERS		BASS	PROCESSOR				MAN'L/AUTO FM	AUTO/MAN'L MONO
A	B	EXTENSION	DIRECT
				STEREO	PROGRAM
				DSP
						SILENT		VIDEO AUX	+	–	+
								–

	TRANSMIT		RE–NAME CLEAR	LEARN
1	SYSTEM
	POWER	STANDBY	SLEEP	6CH INPUT
	A	PHONO	TUNER	CD
	V-AUX	CBL/SAT	MD/TAPE	CD-R
	D-TV/LD	VCR 1	VCR2/DVR	DVD
				SELECT
	POWER		POWER	AMP
	TV		AV

REC

1 Press STANDBY/ON (SYSTEM POWER on the remote control) to turn on the power of this unit.

SYSTEM

POWER

STANDBY /ON

or

Front panel

Remote control

2 Turn on the video monitor connected to this unit.

22

ON-SCREEN DISPLAY (OSD)

You can display the operation information for this unit on a video monitor. If you display the SET MENU and DSP program parameter settings on a monitor, it is much easier to see the available options and parameters than it is by reading this information on the front panel display.

y

•If a video source is being reproduced, the OSD is superimposed over the image.

•The OSD signal is not output to the REC OUT jack, and will not be recorded with any video signal.

•You can set the OSD to turn on (gray background) or off when a video source is not being reproduced (or the source component is turned off) by using “13 DISPLAY SET” on the SET MENU (see page 65).

OSD Modes

You can change the amount of information the OSD shows.

Full display

This mode always shows the DSP program parameter settings on the video monitor.

Short display

This mode briefly shows the same contents as the front panel display at the bottom of the screen and then disappears.

Display off

This mode briefly shows the “DISPLAY OFF” message at the bottom of the screen and then disappears. Afterwards, no changes to operations appear on the monitor except those of the ON SCREEN button.

P01 CONCERT HALL

≥D S P L E V E L … … … … 0 d B I N I T . D L Y … … … … 4 5 m s R O O M S I Z E … … … … 1 . O L I V E N E S S … … … … … … … 5

P 0 1 C O N C E R T H A L L

Selecting the OSD Mode

			SELECT
POWER		POWER	AMP	2
TV		AV
REC
		AUDIO	+
DISC SKIP
			VOL
			–
LEVEL	+	SET MENU	MUTE
TITLE		MENU
TV INPUT	TV VOL	A/B/C/D/E
CH	TV MUTE	CH
–	SELECT	+		3
PRESET		PRESET
TEST	–	ON SCREEN	STEREO
RETURN		DISPLAY
	TV VOL

EFFECT

1 Turn on the video monitor connected to this unit.

2 Press AMP to select the	AMP
AMP mode.
AMP appears in the display
window on the remote control.
3 Press ON SCREEN on the	ON SCREEN
remote control repeatedly	DISPLAY

to change the display mode.

The OSD mode changes in the following order: full display, short display, and display off.

Notes

•If your video monitor is connected only to the COMPONENT VIDEO jacks of this unit, the OSD is not shown. Make sure to connect your video monitor to the COMPONENT VIDEO jacks and either VIDEO or S VIDEO jacks if you want to see the OSD.

•Playing back video software that has an anti-copy signal or video signals with a lot of noise may produce unstable images.

PREPARATION

Full display

Short display

y

•When you choose the full display mode, INPUT, VOLUME and some other types of operation information are displayed at the bottom of the screen in the same format as that for the front panel display.

•The SET MENU and test tone display appear regardless of the OSD mode.

English

23