UAB
AV Receiver
Easy Setup Guide
English
This document explains how to set up a 5.1-channel system and play back surround sound from a BD/DVD on the unit.
To reduce the impact on natural resources, the Owner’s Manual for this product is
supplied on CD-ROM. For more information about this product, refer to the
Owner’s Manual on the supplied CD-ROM.
PDF versions of this guide and “Owner’s Manual” can be downloaded from the following website.
http://download.yamaha.com/
[For U.S. customers only]
Visit the following website for additional information, FAQ’s, downloads such as “Owner’s Manual” and product updates.
http://usa.yamaha.com/support/
Check that the following accessories are supplied with the product.
Remote control |
Batteries (AAA, R03, UM-4) (x2) |
*The supplied remote control varies depending on the model and the region of purchase.
|
|
Insert the batteries the right way round. |
AM antenna |
FM antenna |
YPAO microphone |
|
|
(HTR-3066 only) |
|
*The supplied FM antenna |
|
|
varies depending on the |
|
|
region of purchase. |
|
CD-ROM |
Safety Brochure |
Easy Setup Guide |
(Owner’s Manual) |
|
|
•The illustrations of the main unit and remote control used in this guide are of the HTR-3066 (U.S.A. model), unless otherwise specified.
•(HTR-3066 [Australia model] only)
For information on how to control external devices with the remote control, refer to “Supplement for Remote Control” on the supplied CD-ROM.
The following cables (not supplied) are required to build the system described in this document.
•Speaker cables (x5)
•HDMI cable (x2)
•Audio pin cable (x1)
•Digital optical cable (x1) (not required if your TV supports ARC [Audio Return Channel])
Set up the speakers in the room using the following diagram as a reference.
For information on other speaker systems, refer to “Owner’s Manual”.
1 2
9 3
4 5
10° to 30° |
|
|
|
10° to 30° |
|
|
1Front speaker (L)
2Front speaker (R)
3Center speaker
4Surround speaker (L)
5Surround speaker (R)
9Subwoofer
2En
•(U.S.A. and Canada models only)
Under its default settings, the unit is configured for 8-ohm
speakers. When connecting 6-ohm speakers, set the unit’s speaker impedance to “6 Ω MIN”. For details, see “Setting the speaker impedance” in “Owner’s Manual”.
•Use a subwoofer equipped with built-in amplifier.
•Before connecting the speakers, remove the unit’s power cable from the AC wall outlet and turn off the subwoofer.
•Ensure that the core wires of the speaker cable do not touch each other or come into contact with the unit’s metal areas. This may damage the unit or the speakers. If the speaker cables short circuit, “Check SP Wires” will appear on the front display when the unit is turned on.
■ Connecting speaker cables
Speaker cables have two wires. One is for connecting the negative (-) terminals of the unit and the speaker, and the other is for the positive (+) terminals. If the wires are colored to prevent confusion, connect the black wire to the negative and the other wire to the positive terminals.
(Connecting front speakers)
a Remove approximately 10 mm (3/8”) of insulation from the ends of the speaker cable and twist the bare wires of the cable firmly together.
b Loosen the speaker terminal.
c Insert the bare wires of the cable into the gap on the side (upper right or bottom left) of the terminal.
d Tighten the terminal.
c
+ (red) b
d a
- (black)
Using a banana plug
(U.S.A., Canada, Australia and General models only)
a Tighten the speaker terminal.
b Insert a banana plug into the end of the terminal.
a
Banana plug
b
1Connect the front speakers (1/2) to the FRONT (//\) terminals.
The unit (rear)
SPEAKERS
FRONT
SURROUND CENTER
SUBWOOFER
PRE OUT
(Connecting center/surround speakers)
a Remove approximately 10 mm (3/8”) of insulation from the ends of the speaker cable and twist the bare wires of the cable firmly together.
b Press down the tab.
c Insert the bare wires of the cable into the hole in the terminal.
d Release the tab.
|
OU |
|
|
|
ND |
C |
|
a |
|
ENTER |
|
d b + (red) |
|||
|
c
- (black)
1 2
9 3
4 5
En 3