Toyota Camry 2007-2009 Service Manual - Garage_Door_Opener

GARAGE DOOR OPENER – GARAGE DOOR OPENER SYSTEM

GARAGE DOOR OPENER SYSTEM

SYSTEM DIAGRAM

GD–1

Wiring Diagram

12

Garage Door Opener

LED

SW 3 SW 2 SW 1

DOME

Battery

Image

Garage Door, Gate or Other
Transmitter Code Based System

Signal

Garage Door Opener

Garage Door Opener Switch

Battery

1. DESCRIPTION

(a) A maximum of three codes for transmitter code

based systems such as garage doors, gates, and
entry gates can be registered to the vehicle's
garage door opener system. These stored codes
can then be used to activate the transmitter
controlled systems. It will not be necessary to keep
the original handheld transmitters in the vehicle.

B074550E01

GD

GD

GD–2

GARAGE DOOR OPENER – GARAGE DOOR OPENER SYSTEM

REGISTRATION

1. RESISTER TRANSMITTER CODE

HINT:

• The vehicle's garage door opener system records
transmitter codes for systems such as garage doors,
gates, door locks, home lighting systems, security
systems, or other transmitter-code based systems.

• The garage door opener system is built into the roof
console box assembly. If the roof console box
assembly is replaced, transmitter codes previously
registered in the garage door opener system must be
re-registered.

• Ensure that the customer is aware that existing codes
may be cleared from the garage door opener system
while performing diagnosis of the system. All remotes
required to reprogram the system should be made
available at the time of inspection or repair of the
garage door opener system.

(a) Re-registration of codes in the garage door opener

system. (registration mode)

NOTICE:

• When programming a garage door opener
system, you may operate a garage door or
other device. T o prevent injury , it is necessary
to make sure that people and objects are out
of the way of the garage door or other device.

• Before beginning programming of the garage
door opener system, turn off the engine and
remove the key from the ignition key cylinder .

• The garage door opener system cannot be
used with openers that:
(1) Were manufactured before April 1, 1982.
(2) Do not meet Federal Safety Standards (for
example, garage doors without a jam
protection function).

HINT:

• 3 transmitter codes can be registered with the
garage door opener system. It is possible to
register one handheld transmitter code (original
transmitter) for each of the three garage door
opener system switches.

• Disconnecting the vehicle's battery will not erase
the transmitter codes registered in the garage
door opener system.

• An attempt to overwrite a previously registered
code may fail. In this case, the previously
registered handheld transmitter code will not be
erased.

• To successfully program the garage door opener
system, it may be necessary to replace the
handheld transmitter battery before
programming.

GARAGE DOOR OPENER – GARAGE DOOR OPENER SYSTEM

These Switches

LED

E129941E01

GD–3

(1) Select one of the garage door opener system

switches to program.

(2) Press and hold the selected switch for 20

seconds. The garage door opener system will
enter registration mode. Continue to hold this
switch during steps 3 and 4.
HINT:
The garage door opener system LED should
stay on while holding the selected switch for the
20 second period. After entering registration
mode, the LED will flash approximately 1 time
per second (1 Hz). This indicates that the
garage door opener system has entered
registration mode and is listening for a code
from a handheld transmitter.

Press

Handheld Transmitter

E129943E01

(3) After the garage door opener system has

entered registration mode, bring the original
handheld transmitter within 2 to 9 cm (1 to 3 in.)
of the garage door opener system. Press and
hold the switch on the handheld transmitter. If
the flashing speed of the garage door indicator
light changes from the slow speed to a faster
speed, proceed to step 4.
HINT:
Some handheld transmitters stop transmitting
after 1 to 2 seconds. In this case, continue to
hold the selected garage door opener system
switch while pressing the handheld transmitter
switch for two seconds at a time. Repeat the
cycle of pressing and releasing the transmitter
switch while monitoring for a change of the
flashing speed of the indicator LED.

GD