IAN 289856
Bluetooth® Speaker Tower SSTB 10 B2
Bluetooth® Speaker Tower
Operating instructions and safety instructions
Bluetooth®-SoundTower
Bedienungsanleitung und Sicherheitshinweise
GB / IE / NI Operating instructions and safety instructions Page 1
DE / AT / CH Bedienungsanleitung und Sicherheitshinweise Seite 21
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of
the device.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen
Funktionen des Gerätes vertraut.
a
b C
GB│IE│NI
│
1 ■
SSTB 10 B2
Contents
Introduction ................2
Information concerning these
operating instructions ..............2
Copyright .......................2
Limitation of liability ...............2
Notes on trademarks ..............2
Warnings used ...................3
Intended use .....................3
Safety ..................... 4
Basic safety guidelines .............4
Notes on the radio interface ......... 5
Notes on batteries and
rechargeable batteries .............6
Initial operation ............. 7
Unpacking .......................7
Check the package contents ......... 7
Disposal of packaging materials ...... 7
Set-up location requirements .........8
Electrical connection ...............8
Inserting/changing the remote
control batteries ..................8
Operating components ....... 9
Handling and operation .....10
Operation using the buttons
on the device ....................10
Operation using the buttons
on the remote control .............10
Switch the device on/off ...........11
Connecting a playback device 12
Connecting a playback device
using a 3.5mm jack cable .........12
Connecting a playback device
using a cinch cable ...............12
Pairing the device with a
Bluetooth
®
playback device ......13
Troubleshooting ............14
Cleaning ..................15
Storage/disposal ........... 16
Storage when not in use ...........16
Disposal of the device .............16
Disposal of batteries ..............16
Appendix .................16
Notes on the EU Declaration of
Conformity .....................16
Technical data ...................17
Kompernass Handels GmbH warranty .18
Service ........................19
Importer. . . . . . . . . . . . . . . . . . . . . . . . 19
■ 2│GB
│IE│
NI
SSTB 10 B2
Introduction
Information concerning these operating instructions
Congratulations on the purchase of your new device.
You have selected a high-quality product. The operating instructions
are part of this product. They contain important information on
safety, usage and disposal. Before using the product, familiarise yourself with all
handling and safety guidelines. Use the product only as described and for the
range of applications specified. Keep these operating instructions as a reference
and store them near the product. Please also pass these operating instructions on to
any future owner(s).
Copyright
This documentation is protected by copyright.
Any copying or reproduction, including in the form of extracts, or any repro-
duction of images (even in a modified state), is permitted only with the written
authorisation of the manufacturer.
Limitation of liability
All the technical information, data and instructions regarding installation, connection and operation contained in these operating instructions correspond to the
latest information available to us at the time of printing and take into account
our previous experience and know-how.
No claims can be derived from the details, illustrations and descriptions in these
instructions.
The manufacturer assumes no responsibility for damage caused by failure to
observe these instructions, improper use, incompetent repairs, unauthorised
modifications or for the use of non-approved replacement parts.
Notes on trademarks
The Bluetooth® word mark and Bluetooth® logos are registered trademarks
owned by Bluetooth SIG, Inc. (Special Interest Group). Any use of the trademarks by Kompernaß Handels GmbH is made under the provisions of a licence.
The SilverCrest trademark and the retail name are the property of their respective
owner.
All other names and products may be trademarks or registered trademarks of
their respective owners.
GB│IE│NI
│
3 ■
SSTB 10 B2
Warnings used
The following warnings are used in these operating instructions:
DANGER
A warning at this hazard level indicates a potentially hazardous
situation.
Failure to avoid this hazardous situation could result in severe injuries or
even death.
► Follow the instructions in this warning notice to avoid the risk of serious
injuries or death.
CAUTION
A warning at this hazard level indicates potential property
damage.
Failure to avoid this situation could result in property damage.
► Follow the instructions in this warning to prevent property damage.
NOTE
► A note provides additional information that will assist you in using the device.
Intended use
This is a consumer electronics device and is exclusively for the playback of audio
files via Bluetooth®, cinch cable and 3.5 mm jack cable.
The device is intended for private use only and is not suitable for commercial
purposes. It is not intended for any other use or use beyond that specified.
Claims of any kind for damage arising as a result of incorrect use will not be
accepted. The risk shall be borne solely by the user.
■ 4│GB
│IE│
NI
SSTB 10 B2
Safety
In this section, you will find important safety instructions for using the device.
The device complies with the statutory safety regulations. Improper use may
result in personal injury and property damage.
Basic safety guidelines
To ensure safe operation of the device, follow the safety guidelines set out below:
■ Prior to use, check the device for visible external damage. Do not operate
a device that has been damaged or dropped.
■ If the cables or connections are damaged, have them replaced by an authorised
specialist or the Customer Service department.
■ Do not use the device if the mains power adapter or the connection cable are
damaged.
■ The mains adapter and the welded connection cable may not be repaired. In
the event of a defect, the entire mains adapter must be replaced with another
of identical design.
■ This appliance may be used by children aged 8 over and by persons with
reduced physical, sensory or mental capabilities or lack of experience and
knowledge, provided that they are under supervision or have been told how
to use of the appliance safely and are aware of the potential risks. Children
must not play with the appliance. Cleaning and user maintenance tasks must
not be carried out by children unless they are supervised.
■
DANGER! Do not allow children to play with the packaging material!
Keep all packaging materials out of the reach of children.
Risk of suffocation!
■ Never open the device housing. None of the components in the device can
be serviced or replaced by the user.
■ Do not make any unauthorised modifications or alterations to the device.
■ All repairs must be carried out by authorised specialist companies or by the
Customer Service department. Failure to make proper repairs can put the
user at risk. It will also invalidate any warranty claim.
■ Defective components must always be replaced with original replacement
parts. Compliance with safety requirements can only be guaranteed if original
replacement parts are used.
■ Use the device and the mains adapter only in dry rooms.
■ Protect the device from drips or splashes of water. Never submerge the
device in water, do not set up the device in the vicinity of water and do not
place any object filled with liquid (i.e. vases) on or next to the device.
GB│IE│NI
│
5 ■
SSTB 10 B2
■ Do not place any heavy objects on the device. The storage compartment is
used only for storage of connected playback devices.
■ Keep the device away from open flames (e.g. candles) at all times. Do not
place burning candles on or next to the product. This will help to prevent
fires.
■ Avoid exposing the device to direct sunlight.
■ If you move the device quickly from a warm to a cold room or vice versa,
allow the device at least 30minutes to acclimatise.
■ Operate the device only with the supplied mains adapter.
■ To avoid damage caused by improper warming, do not cover the mains
power adapter.
■ The
/ FUNC. button on this device does not completely disconnect the
device from the mains power supply. In addition, the mains adapter consumes power as long as it is connected to the power socket (standby mode).
To completely disconnect the device from the power supply, the plug must be
removed from the mains power socket.
■ To disconnect the mains adapter, always pull only on the plug itself, not on
the power cable.
■ Never touch the mains adapter or the connecting cable with wet hands!
■ The mains power socket that is used must be easily accessible at all times so
that the mains adapter can be quickly removed from the mains power socket
in the event of an emergency.
■ In the case of a malfunction, unusual noises or smoke or a thunderstorm, dis-
connect the mains adapter from the power socket. Have the device checked
by a qualified specialist before using it again.
Notes on the radio interface
■ Keep the device at least 20 cm away from a pacemaker, as the proper
functioning of the pacemaker could be affected by radio waves.
■ The transmitted radio waves can cause noise interference in hearing aids.
■ Do not use the device with the radio components switched on in the presence of
flammable gases or in a potentially explosive atmosphere (e.g. in a paint shop),
as the transmitted radio waves can cause an explosion or ignite a fire.
■ The range of the radio waves is dependent on the environment and the ambi-
ent conditions.
■ Data transmissions via a wireless connection can be intercepted by unauthor-
ised third parties.
■ 6│GB
│IE│
NI
SSTB 10 B2
Notes on batteries and rechargeable batteries
DANGER
Mishandling batteries can cause fires, explosions, leakages or
other hazards!
► Do not swallow the batteries; there is a danger of chemical burns.
► Keep new and used batteries away from children.
► If the battery compartment does not close securely, stop using the product
and keep it away from children.
► If you suspect batteries may have been swallowed or have got into any
part of the body, seek immediate medical help.
► Batteries must never be short-circuited, taken apart, deformed or thrown
into a fire. There is a risk of explosion!
► Chemicals from leaking or damaged batteries can cause skin irritations
when touched. Therefore, use suitable protective gloves. In the event of
contact with the skin, rinse with plenty of water. If the chemicals come into
contact with your eyes, rinse thoroughly with plenty of water, do not rub
and consult a doctor immediately.
► Do attempt to recharge non-rechargeable batteries. There is a risk of fire
and/or explosion!
► When inserting the batteries, note the correct polarity (plus/+ and minus/−).
► Do not mix different types of batteries. Empty batteries should be removed
because of the increased risk of leakage.
► During extended periods of non-use (e.g. during storage), remove the
batteries from the remote control to prevent damage caused by battery
leakage.
GB│IE│NI
│
7 ■
SSTB 10 B2
Initial operation
Unpacking
♦ Remove all parts of the device and the operating instructions from the box.
♦ Remove all packaging material.
Check the package contents
(For illustrations see the fold-out page)
The following components are included in delivery:
● Bluetooth
®
Speaker Tower SSTB 10 B2
● Mains adapter QXS24C-120200B
● Remote control
● 2 x 1.5 V batteries type AAA/micro
● These operating instructions
NOTE
► Check the package for completeness and for signs of visible damage.
► On delivery, the mains adapter and the remote control can be found in the
rigid foam packing directly under the lid of the box. Pull the rigid foam out
of the lid of the box to remove the mains adapter and the remote control.
► If the consignment is incomplete or damaged due to defective packaging
or carriage, contact the Service hotline (see the chapter Service).
Disposal of packaging materials
The packaging protects the device from damage during shipment. The packaging
materials have been selected for their environmental friendliness and ease of
disposal, and are therefore recyclable.
Returning the packaging to the materials cycle conserves raw materials
and reduces the amount of waste that is generated. Dispose of
packaging materials which are no longer needed in accordance with
applicable local regulations.
NOTE
► If possible, keep the original packaging of the device during the warranty
period so that the device can be packed properly for returning in the event
of a warranty claim.
■ 8│GB
│IE│
NI
SSTB 10 B2
Set-up location requirements
For safe and trouble-free operation of the device , the set-up location must fulfil
the following requirements:
■ Place the device on a firm, flat and level surface.
■ Do not operate the device in a hot, wet or extremely damp environment.
■ Keep a minimum distance of 30 cm to heat-emitting devices such as heaters,
ovens, etc.
■ Only operate the device in locations with adequate ventilation.
Electrical connection
■ Before you connect the device, compare the connection data (voltage and
frequency) on the mains adapter type plate with that of the intended power
source. These data must agree so that no damage is sustained by the device.
■ Make sure that the mains adapter’s connection cable is not damaged and is
not laying over hot surfaces and/or sharp edges.
■ Connect the plug of the connecting cable into the connector for the power
supply on the rear of the unit and plug the mains adapter into a power
outlet. Ensure that the power cable is not stretched tightly or kinked.
■ Place the connecting cable such that no one can stumble over it.
■ Do not place the device, furniture or any other objects on the cable. Do not
kink the cable or knot it and do not connect it to other cables. Never wrap
the cable tightly around other objects otherwise the conductors inside the
cable could break and cause a malfunction.
Inserting/changing the remote control batteries
To insert/change the batteries, proceed as follows:
♦ Pull the cover off the battery compartment of the remote control.
♦ Remove any depleted batteries and insert two new type AAA/micro batteries
into the battery compartment. Be sure to insert the batteries with the correct
polarity.
♦ Slide the cover back onto the battery compartment until it clicks into place.
GB│IE│NI
│
9 ■
SSTB 10 B2
Operating components
(For illustrations see the fold-out page)
Figure A:
Display
Storage tray
Infrared sensor
/ PAIR button
button
button
button
button
/ FUNC. button
DC IN connection socket
AUX 1 connection socket (3.5 mm jack)
AUX 2 connection socket (audio input jack R/L)
Figure B:
button
Movie button
button
Flat button
button
VOL + button
/ PAIR button
button
TREBLE + button
TREBLE − button
Indiv. button
BASS − button
BASS + button
VOL − button
button
AUX button
Music button
Figure C:
Mains adapter
2 x 1.5 V batteries type AAA/micro
Operating instructions (symbol)
■ 10│GB
│IE│
NI
SSTB 10 B2
Handling and operation
This section provides you with important information on handling and using the
device.
NOTE
► Most of the device’s functions can be operated by the buttons on the
device as well as by the buttons on the remote control.
Operation using the buttons on the device
Button Function
/ FUNC.
– Press briefly to switch on the device and activate the
Bluetooth® function.
– With the device switched on, press to switch between the
operating modes (AUX and Bluetooth®).
– Press for 2 seconds to switch the device off and deacti-
vate the Bluetooth® function.
/ PAIR
– Press once to start/stop playback.
– Press for 2 seconds to stop the current Bluetooth
®
connection. The device is now ready to be paired with
another Bluetooth
®
device.
– Press to jump to the next track.
– Press to jump to the previous track.
– Press to increase the volume.
– Press to decrease the volume.
Operation using the buttons on the remote control
Button Function
– Press to switch the device on/off and to activate/
deactivate the Bluetooth
®
function.
/ PAIR
– Press to start/stop playback.
– Press for 2 seconds to stop the current Bluetooth
®
connection. The device is now ready to be paired with
another Bluetooth® device.
– Press to jump to the next track.
– Press to jump to the previous track.
VOL +
– Press to increase the volume.
VOL −
– Press to decrease the volume.
GB│IE│NI
│
11 ■
SSTB 10 B2
Button Function
– Press to mute playback.
AUX
– Press to activate the AUX mode.
– Press to switch on the Bluetooth® function.
Music
Movie
Flat
– Press to activate one of the three preset sound pro-
grammes. The
BASS +, BASS −, TREBLE + and
TREBLE −
buttons are inactive.
Indiv.
– Press to activate the individual sound programmes.
The
BASS +, BASS −, TREBLE + and TREBLE −
buttons are active.
BASS +
– Press to increase the bass tones.
BASS −
– Press to decrease the bass tones.
TREBLE +
– Press to increase the treble tones.
TREBLE −
– Press to decrease the treble tones.
Switch the device on/off
On the device
♦ Briefly press the / FUNC. button to switch the device on.
The message HIappears briefly on the display and then the most
recently used operating mode (AUX or bLUE) is shown.
♦ Press the
/ FUNC. button for about 2 seconds to switch off the
device. The message OFF appears briefly on the display .
With the remote control
♦ Press the button to switch on the device.
♦ Press the
button again to switch off the device.
Loading...