BLENDER SSM 600 B2
BLENDER
Operating instructions
STANDMIXER
Bedienungsanleitung
IAN 296694
ΜΠΛΈΝΤΈΡ
Οδηүίες χρήσης
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of
the device.
Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τη σελίδα με τις εικόνες και εξοικειωθείτε με όλες τις λειτουργίες
της συσκευής.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen
Funktionen des Gerätes vertraut.
GB / IE / NI / CY Operating instructions Page 1
GR / CY Οδηүίες χρήσης Σελίδα 19
DE / AT / CH Bedienungsanleitung Seite 37
Content
Introduction ...................................................2
Intended use ..................................................2
Package contents ..............................................2
Description of the appliance .....................................3
Technical data .................................................3
Safety instructions .............................................4
Unpacking ....................................................6
Setting up .....................................................6
Operation ....................................................7
Fitting and filling the blender ...............................................7
Selecting the speed setting ................................................. 8
Filling while in use ........................................................ 8
Removing the blender ..................................................... 9
Useful tips ....................................................9
Recipes ......................................................10
Banana shake .......................................................... 10
Vanilla shake ...........................................................10
Cappucino shake ........................................................ 10
Tropical mix ............................................................10
Nut nougat shake ....................................................... 11
Carrot shake ........................................................... 11
Blackcurrant mix ........................................................ 11
Hawaii shake ........................................................... 11
Fruity pineapple and strawberry mix ......................................... 12
Andalusian cold soup (gazpacho) .......................................... 12
Cleaning ....................................................13
Cleaning the blender ..................................................... 13
Cleaning the motor block .................................................15
After cleaning ..........................................................15
Storage .....................................................15
Disposal .....................................................16
Kompernass Handels GmbH warranty ............................16
Service ................................................................ 18
Importer ............................................................... 18
SSM 600 B2
GB│IE│NI│CY
│
1 ■
Introduction
Congratulations on the purchase of your new appliance.
You have selected a high-quality product. These operating instructions are a part
of this product. They contain important information on safety, usage and disposal.
Before using the product, familiarise yourself with all operating and safety instructions. Use the product only as described and only for the specified areas of
application. In addition, pass these documents on, together with the product,
to any future owner.
Intended use
This appliance is intended exclusively for...
■ mixing, puréeing and stirring foods as well as crushing ice cubes,
■ use exclusively in normal domestic amounts and only for private use in a
domestic environment in dry rooms.
This appliance is not intended for ...
■ the chopping of hard foodstuffs, such as nuts, seeds, large kernels or stalks,
■ the processing of materials that are not foodstuffs,
■ commercial or industrial use,
■ for use in damp environments or outdoors,
■ processing hot/boiling liquids.
Use only the accessories and spare parts that are specified for this appliance.
Other parts may not be adequately suitable or safe!
Package contents
After unpacking, check to ensure all items are available. The package contains:
▯ Motor block, with power cable and plug
▯ Blender
▯ Lid
▯ Measuring cap
▯ Operating instructions
■ 2 │ GB
│IE│NI│
CY
SSM 600 B2
Description of the appliance
1 Measuring cap
2 Lid
3 Blender
4 Cutting blades
5 Switch
6 Motor block
7 Cable retainer
8 Scale
9 Rubber lid seal
Technical data
Nominal voltage 220–240 V ∼ (AC), 50 - 60 Hz
Nominal power consumption
Max. capacity 1.75 litres
Protection class
CO time 3 Minuten
The CO time (continuous operation time) is the amount of time an appliance can
be operated without the motor overheating and becoming damaged. When the
specified CO time has been reached, the appliance must be switched off until
the motor has cooled down to room temperature.
600 W
II /
All of the parts of this appliance that come
into contact with food are food-safe.
(Double insulation)
SSM 600 B2
GB│IE│NI│CY
│
3 ■
Safety instructions
DANGER! ELECTRIC SHOCK!
► Ensure that the appliance, the power cable and the power
plug are never immersed in water or other liquids.
► Use the appliance only in dry rooms; never use it outdoors
or in damp environments.
► Ensure that the power cable never becomes wet or damp
during operation. Route the power cable in such a way that
it cannot become trapped or damaged in any way.
► Arrange for defective power plugs and/or cables to be
replaced as soon as possible by a qualified technician or by
our Customer Service Department to avoid the risk of injury.
► Always remove the plug from the power socket after use.
Switching off the appliance is not sufficient because the
appliance receives power as long as the power plug is connected to the socket.
► Check to ensure that the appliance is in a serviceable con-
dition before use. The appliance may not be used if it shows
signs of damage, especially to the motor block or the blender
attachment.
► Remove the plug from the socket immediately if you notice
unexpected smells or noises coming from the appliance
while it is in use or if there is an evident malfunction.
WARNING! RISK OF INJURY!
► NEVER insert your hand or fingers into the blender, especially
when it is in use. The cutting blades are extremely sharp!
► DO NOT remove the lid when the appliance is in operation.
► To ensure you can react immediately in the event of danger,
never leave the appliance running unattended.
■ 4 │ GB
│IE│NI│
CY
SSM 600 B2
WARNING! RISK OF INJURY!
► Do not insert cutlery items or mixing tools into the blender while
the appliance is in use. There is a considerable risk of injury if
these come into contact with the swiftly rotating cutting blades!
► Children should be supervised to ensure that they do not
play with the appliance.
► Never use the appliance for purposes other than those described
in these instructions.
► Risk of injury if appliance is misused.
► The appliance should always be disconnected from the mains
when not supervised and before assembly, disassembly or
cleaning.
► This appliance is not to be used by children.
► The appliance and its mains cable must be kept away from
children.
► This appliance can be used by persons with reduced physical,
sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction
concerning safe use of the appliance, and if they are aware
of the potential risks.
► Do not allow children to play with the appliance.
► Be careful when handling the appliance. The cutting blades
are extremely sharp!
► Take care when emptying the blender! The cutting blades
are extremely sharp!
► Take care when cleaning the appliance! The cutting blades
are extremely sharp!
► Switch the appliance off and disconnect the plug from the
power supply before changing accessories or getting hold
of parts that move during operation.
SSM 600 B2
GB│IE│NI│CY
│
5 ■
WARNING! RISK OF INJURY!
► Always make sure that the blender is switched off before
removing the jug from the motor block!
► Use the blender only with the supplied motor block!
CAUTION! MATERIAL DAMAGE!
► Do not use the appliance in direct sunlight or near any heat-
generating appliances.
► NEVER fill the blender with boiling liquids or other foods!
Allow these to cool to a lukewarm temperature.
► NEVER operate the appliance when it is empty, i.e. without
ingredients in the blender attachment.
Unpacking
■ Remove all packaging materials or protective films from the appliance. Retain
the packaging, so that you can store the appliance safely or send it by post,
e.g. if it needs to be repaired.
■ Before using the appliance, check that it is free of damage; check also that
the power cable and plug as well as all accessories and appliance parts are
undamaged.
■ Clean all components carefully before using the appliance for the first time
(see “Cleaning”).
Setting up
Once all components have been cleaned as described in the section “Cleaning”:
■ Position the appliance so that, ...
■ 6 │ GB
│IE│NI│
– that the mains cable passes through the recess at the rear of the appli-
ance,
– the power plug is immediately accessible, so that it can be quickly
withdrawn in the event of danger,
– that it is stable and not liable to slip, and so that the sucker feet can
attach firmly and the appliance cannot tip over due to vibration,
– that the mains cable is not in the working area and thus does not present a
risk of being inadvertently snagged and tipping the appliance over.
CY
SSM 600 B2
Operation
WARNING!
► The motor switches off automatically as soon as the blender 3 is removed
from the motor block 6 or the lid 2 is opened. In such cases it may be
easy to forget that the machine is still switched on. The motor will then start
unexpectedly as soon as the blender attachment 3 is fitted or the lid 2 is
closed again:
Therefore:
– Do not insert the power plug into the wall socket until the blender 3 is
filled and mounted with its lid fitted and closed.
– Before fitting the blender, always check to see that the appliance is
switched off or that the power plug has been removed.
– Switch the appliance off first, pull the plug out and wait until the motor
has come to a standstill before removing the blender 3 or opening the
lid 2.
Fitting and filling the blender
1) Rotate the blender 3 anticlockwise until the arrow q under the blender
handle is located above the
motor block 6 in a vertical, upward motion.
2) Remove the lid 2 by rotating it anticlockwise towards position
until you can pull it upwards.
3) Fill the blender 3.
4) Press the lid 2 firmly down onto the blender 3. Close the lid 2 by turning
it clockwise to position
pouring spout on the blender 3 is closed. The motor cannot start until the lid
2 is fitted flush.
until it audibly engages (see Fig. 2). Ensure that the
position. Remove the blender 3 from the
(see Fig 1)
5) Press the measuring cap 1 into the lid as far as the stop.
SSM 600 B2
Fig. 1 Fig. 2
GB│IE│NI│CY
│
7 ■
6) Place the filled and closed blender 3 on the motor block 6. To do this,
use the recesses on the motor block 6 and ensure that the arrow q on the
blender is pointing to the
clockwise to position
the blender 3 is fitted flush.
until it audibly engages. The motor cannot start until
Selecting the speed setting
Once the blender 3 is filled and sitting completely closed on the motor block 6,
you can switch on the appliance.
Set the switch 5 to...
■ Level 1–3
for liquids or soft foodstuffs, for mixing, blending and stirring
■ Level 3–5
for more solid foods or for chopping
■ Level Ice Crush/Clean
for short, powerful impulse operation, e.g. for crushing ice cubes or when
cleaning. To prevent overloading the motor, the switch 5 does not lock in this
position. Therefore, hold the switch 5 in this position for short periods only.
NOTE
► Fill the blender 3 with a maximum of 180 g of ice cubes.
Otherwise, the ice cubes will not be crushed optimally.
Filling while in use
symbol while doing so. Turn the blender 3
■ 8 │ GB
WARNING!
► If you want to add additional foods during operation, use only the measuring
cap 1 provided for this purpose. Do NOT open the lid 2.
► Do not insert cutlery items or mixing tools into the blender 3 while the
appliance is in use. There is a considerable risk of injury if these come into
contact with the swiftly rotating cutting blades 4!
To add more food while the appliance is in use, ...
1) Remove the measuring cap 1 from the lid 2.
2) Add the ingredients.
3) Press the measuring cap 1 back into the lid.
│IE│NI│
CY
SSM 600 B2
Removing the blender
Once you have finished processing the food in the attachment:
1) Always start by setting switch 5 to the off position (“0”) and pulling out the
mains plug.
2) Wait until the motor has come to a complete standstill before lifting the
blender 3 off the motor block 6. Rotate the blender 3 anticlockwise until
the arrow q under the blender handle is located above the
Remove the blender 3 from the motor block 6 in a vertical, upward motion.
Useful tips
■ To achieve the best results when puréeing firm ingredients, add small amounts
one after the other into the blender 3 rather than a single large portion.
■ When processing firm ingredients, cut them into small pieces (2–3 cm).
■ When mixing liquid ingredients, start off with a small amount of liquid. Grad-
ually add more liquids to the mixture through the measuring cap.
■ The appliance can be stabilised by placing your hand on top of the closed
blender during operation.
■ When stirring firm or very viscous foods, it can be helpful to use the level Ice
Crush/Clean to avoid a blocking of the cutting blades 4.
NOTE
► Do not use the appliance to grind crystals of cooking salt, refined sugar or
white sugar. For example, to make powdered sugar.
position.
SSM 600 B2
GB│IE│NI│CY
│
9 ■
Recipes
Banana shake
▯ 2 bananas
▯ approx. 2 tbsp. sugar
(depending on the ripeness of the bananas and personal taste)
▯ ½ l milk
▯ 1 dash of lemon juice
Peel the bananas and liquidise them at level 2. Gradually add the milk, then the
sugar and the lemon juice. Keep mixing everything until you have a smooth and
uniform liquid. Serve the shake chilled.
Vanilla shake
▯ ¼ l milk
▯ 250 g vanilla ice cream
▯ 125 ml ice cubes
▯ 1½ tsp. sugar
Crush the ice cubes using the level Ice Crush/Clean. Place the remaining ingredients
into the mixer. Mix everything at Level 2 until the liquid has a smooth consistency.
Cappucino shake
▯ 65 ml cold espresso (or a very strong coffee)
▯ 65 ml milk
▯ 15 g sugar
▯ 65 ml vanilla ice cream
▯ 100 ml ice cubes
Crush the ice cubes using the level Ice Crush/Clean. Add the espresso, milk and
sugar. Mix everything together at level 2 until the sugar has dissolved. Finally,
add the vanilla ice cream and then briefly mix everything together at level 1.
Tropical mix
▯ 125 ml pineapple juice
▯ 60 ml papaya juice
▯ 50 ml orange juice
▯ ½ small tin of peaches with juice
▯ 125 ml ice cubes
Crush the ice cubes using the level Ice Crush/Clean. Place all ingredients into the
mixer and blend them together at level 3.
■ 10 │ GB
│IE│NI│
CY
SSM 600 B2
Nut nougat shake
▯ ½ l milk
▯ 200 g nut nougat spread
▯ 1 scoop of vanilla ice cream
▯ 50 ml cream
Add all the ingredients to the blender and mix at level 3 until everything is evenly
blended together.
Carrot shake
▯ 300 ml apple juice
▯ 500 ml carrot juice
▯ 4 tbsp. cooking oil (wheatgerm oil or rapeseed oil)
▯ 4 tbsp. of lemon juice
▯ Powdered ginger
▯ Pepper
Add the apple juice, cooking oil and lemon juice into the blender and mix
everything together at level 2. Then add the carrot juice and mix everything
together at level 2. To finish, add the powdered ginger and pepper to taste.
Blackcurrant mix
▯ 2 tsp. honey
▯ 2 bananas
▯ ¼ l buttermilk
▯ ¼ l blackcurrant juice
Place all ingredients into the mixer and blend them together at level 3.
Hawaii shake
▯ 4 bananas
▯ ¼ l pineapple juice
▯ ½ l milk
▯ 2 tbsp. honey
▯ ¼ l rum
Peel the bananas and liquidise them at level 2. Then add the other ingredients
and mix everything together at level 1.
SSM 600 B2
GB│IE│NI│CY
│
11 ■
Fruity pineapple and strawberry mix
▯ 250 ml pineapple juice
▯ 200 g strawberries
▯ 300 ml apple juice
▯ 4 ice cubes
Crush the ice cubes using the level Ice Crush/Clean. Wash the strawberries and
remove the green parts. Liquidise them at level 2. Then add the other ingredients
and mix everything together at level 1.
Andalusian cold soup (gazpacho)
▯ ½ cucumber
▯ 1 large tomato
▯ 1 green pepper
▯ ½ onion
▯ 1 garlic clove
▯ ½ white bread roll
▯ ½ tsp. salt
▯ 1 tsp. red wine vinegar
▯ 1 tbsp. olive oil
Cut the vegetables into pieces approx. 2 cm in size. Start by adding the first the
tomatoes and then the cucumber to the blender. Liquidise them at level 3. Add
the remaining ingredients and then liquidise/blend them all together at level 3
until a smooth soup is created. Serve the soup with bread.
■ 12 │ GB
NOTE
► These recipes are provided subject to change. All ingredients and prepara-
tion information are guiding values. Adapt these recipe suggestions based
on your personal experience.
NOTE
► In cases of lactose intolerance, we recommend you use a lactose-free milk.
Keep in mind, however, that lactose-free milk is a little sweeter.
│IE│NI│
CY
SSM 600 B2
Cleaning
RISK OF ELECTRIC SHOCK!
Before starting to clean the blender and its components:
► Ensure that the motor is switched off and the power plug removed from the
socket.
Do not immerse the motor block 6 in water or other liquids. This could
result in you receiving a fatal electric shock and cause damage to the
appliance.
► Never open the housing of the appliance. Otherwise, there is a risk of a
fatal electric shock.
WARNING! RISK OF INJURY!
► Never disassemble the cutting blades 4 and never reach into the blender 3.
The cutting blades 4 are extremely sharp!
CAUTION – PROPERTY DAMAGE!
► Do not use solvents or abrasive cleaners on the plastic surfaces, they could
be damaged by them.
Cleaning the blender
■ To prevent injuring yourself on the cutting blades 4, clean the blender 3 only
with a long-handled washing-up brush.
■ Clean the measuring cap 1 and the lid 2 in mild soap solution. Ensure that
the rubber seal 9 is correctly fitted before using the lid 2 again.
NOTE
SSM 600 B2
You can also clean the lid 2, the measuring cap 1 and the blender
3 with the cutting blade 4 in your dishwasher.
■ If you clean the blender directly after use, you can often achieve a satisfacto-
ry and hygienic level of cleaning by doing the following:
Fill the blender 3 with 750 ml of water and add a few drops of mild
detergent. Close the lid 2 and fit the blender 3 onto the motor block 6.
Insert the plug into a mains power socket and activate the Ice Crush/Clean
operation a few times, so that the cutting blades 4 churn through the water
at full speed.
Afterwards, rinse out the blender 3 with lots of clean water to ensure that
all detergent residues have been removed.
GB│IE│NI│CY
│
13 ■
■ To remove stubborn dirt, you can remove the lower plastic part of the blend-
er 3 with the cutting blade 4 from the upper plastic part of the blender 3:
C
B
A
Fig. 3
A upper plastic part
B blade
C lower plastic part
1) Remove the blender 3 from the motor block 6. To ensure improved stability,
remove the lid 2 by rotating it anticlockwise towards position
until you can pull it upwards.
2) Turn the appliance upside down and turn the lower plastic part C of the
blender 3 anticlockwise so that it can be removed from the upper plastic part
A of the blender 3 (see fig. 3).
(see Fig 1)
■ 14 │ GB
WARNING! RISK OF INJURY!
► Always handle the blades B carefully. They are very sharp.
Risk of injury!
3) Clean both parts thoroughly in a mild soap solution.
│IE│NI│
CY
SSM 600 B2
NOTE
You can also clean the upper plastic part A of the blender 3 and
the cutting blade 4 with the lower plastic part C in your dishwasher.
4) Dry all parts thoroughly before reassembling them.
5) Re-attach the lower plastic part C of the blender 3 to the upper plastic part
A of the blender 3 and turn it clockwise.
Cleaning the motor block
1) Use a dry or no more than slightly moistened cloth to clean the plastic
surfaces.
2) When cleaning, always check that the contact switch in the fitting for the
blender 3 is not blocked by soiling residues. If you cannot dislodge any
blockages with the corner of a piece of paper, make contact with Customer
Services. Do not use any hard objects, these could damage the contact
switch.
3) Remove any possible residues on the underside of the motor block 6 with a
dry cloth or a stiff-bristled brush only. Ensure that nothing can get in through
the ventilation openings of the appliance.
After cleaning
Allow all parts to dry well before reassembling and reusing the liquidiser.
Storage
1) If you do not intend to use the blender for an extended period, clean it
thoroughly (see chapter “Cleaning”).
2) Wrap the power cable around the cable retainer 7 on the base of the
motor block 6.
3) Store the blender in a cool and dry location.
SSM 600 B2
GB│IE│NI│CY
│
15 ■
Loading...