Congratulations on the purchase of your new appliance.
You have selected a high-quality product. The operating instructions are part of
this product. They contain important information on safety, usage and disposal.
Before using the product, familiarise yourself with all handling and safety guidelines. Use the product only as described and for the range of applications specified. Keep these operating instructions in a safe place Upon cession of the
product to a third party, also hand over all documents
Copyright
This documentation is subject to copyright protection.
Any reproduction, or any reprint, also in excerpted form, as well as the rendition
of figures, also in modified form, shall be permitted solely upon obtaining the
written consent of the manufacturer.
Limitation of liability
At the time of going to print, all the technical information, data and guidelines for
installation and handling contained in these operating instructions are consistent
with the state of the art, and - to the best of our knowledge - have been constituted
duly taking into account our experience and understanding.
No claims may be derived from the specifications, figures and descriptions in
these operating instructions.
The manufacturer assumes no liability for damages sustained in consequence of
non-adherence to the operating instructions, inappropriate use, improper repairs,
modifications undertaken without permission or the use of unauthorised spare
parts.
Intended use
The appliance is exclusively intended to dehumidify living spaces, basements or
storage areas with an ambient temperature of 5 °C to 35 °C. The appliance
may only be used indoors. The appliance is intended solely for personal use
and not for commercial deployment. Usage other than as described above is
impermissible and may result in injury and/or damage to the appliance.
The manufacturer shall assume no liability for damage attributable to misuse.
The risk shall be borne solely by the user.
■ 2 │ GB
│
CY
SLE 320 A2
Warnings used
The following warnings are used in these operating instructions:
DANGER
A warning at this risk level indicates an imminently hazardous
situation.
If the hazardous situation is not avoided, it could result in death or serious
physical injury.
► Follow the instructions in this warning to prevent a fatality or serious
personal injury.
WARNING
A warning at this risk level indicates a potentially hazardous
situation.
Failure to avoid this hazardous situation could result in physical injury.
► Follow the instructions in this warning to prevent physical injury.
CAUTION
A warning at this risk level indicates potential material
damage.
Failure to avoid this situation could result in material damage.
► Follow the instructions in this warning to prevent material damage.
SLE 320 A2
NOTE
► A note indicates additional information that eases appliance handling.
GB│CY
│
3 ■
Safety
In this section, you will receive important safety advice relating to appliance
handling. Improper use may result in personal injury and material damage.
Risk of electrocution
DANGER
Risk of fatal injury from electrocution!
Contact with live cables or components can result in
fatal injury!
Please observe the following safety guidelines to prevent
electrical hazards.
► Do not use the appliance if the power cable or the con-
necting plug is damaged.
► There is a risk of electrocution if live connections are
touched and the electrical and mechanical structure is
changed.
Risk of electrocution due to moisture
DANGER
► Do not place the appliance in water, nor in water pool-
ing areas or in puddles.
■ 4 │ GB
► The appliance may never be operated near a bath tub,
a shower, a filled wash basin or similar structures.
► The appliance, the connection cabling and the mains
plug may not be immersed in water or other fluids.
► Protect the appliance against drops or splashes of water.
► In the event that fluid should enter the appliance (apart
from in the water tank), immediately disconnect the mains
plug. Arrange to have the appliance checked before putting it into operation again after a period of remission.
► Do not handle the appliance with damp hands.
► Should the appliance have fallen into water, disconnect the
mains plug immediately. Remove the appliance only thereafter.
│
CY
SLE 320 A2
Risk of explosion
DANGER
► Do not use the appliance in a potentially explosive environ-
ment containing combustible liquids, gases or dusts. Electrical
appliances generate sparks that can ignite the dust or fumes.
Risk of disease
DANGER
► The stored water is not suitable for drinking or watering.
There are potential health hazards.
WARNING OF MATERIAL DAMAGE
► Do not use the appliance in swimming pools, wash rooms
or similar facilities.
► The appliance is not suitable for drying lagging. If, after
a pipe has burst, insulation or lagging materials become
damp, consult an expert under all circumstances.
► Never expose the appliance to temperatures of 0 °C
or lower. Residual water in the pipes could freeze and
damage the system.
► Do not use the appliance in a dusty or chlorinated envi-
ronment.
Basic safety guidelines
To ensure safe handling of the appliance, follow the safety
guidelines set out below
■ Prior to use, check the appliance for visible, external dam-
age. Do not operate an appliance that has been damaged
or dropped.
■ Should the connecting cable or the connections be damaged,
have them exchanged by authorised specialist staff or by the
Customer Service department in order to prevent hazards.
■ Do not operate the appliance outdoors.
SLE 320 A2
GB│CY
│
5 ■
■ During operation, always keep windows and doors closed
so that the appliance can work effectively.
■ Do not operate the appliance in the proximity of highly in-
flammable gases or materials, near naked flames or in areas
prone to oil and water splashing.
■ This appliance may be used by children aged 8 years and
above and by persons with limited physical, sensory or
mental capabilities or lack of experience and knowledge,
provided that they are under supervision or have been told
how to use the appliance safely and are aware of the potential risks. Children must not use the appliance as a plaything.
Cleaning and user maintenance tasks may not be carried
out by children unless they are supervised.
■ All repairs must be carried out by authorised specialist com-
panies or by the Customer Service department. Improper
repairs can pose significant risks to the user. Warranty entitlement shall also lapse.
■ This appliance should not be exposed to rain. Protect the ap-
pliance against moisture and the ingress of fluids and objects
into the casing. Never immerse the appliance in water and
do not place objects containing fluids (such as vases) on the
appliance. The appliance may be irreparably damaged.
■ 6 │ GB
■ Heavy objects are not to be placed on the appliance.
■ The appliance is not to be covered (e.g. with newspapers,
cushions or blankets).
■ No objects are to be inserted into the ventilation grille.
■ Avoid direct sunlight.
■ Naked flames, such as burning candles, may not be placed
upon or directly alongside the appliance.
■ In the event that malfunctions occur, and in bad weather,
disconnect the plug from the mains power socket.
■ Always ensure that the air inlet and air outlet apertures remain
free of soiling during operation. Never cover the appliance!
│
CY
SLE 320 A2
■ Always place the appliance on a solid, flat surface so that it
cannot tip over.
■ Do not mount the appliance. Position the appliance’s side
panels so as to allow a clearance of at least 20 cm from
walls or other objects, and ensure a clearance of at least 50
cm from the front, rear and top panels of the appliance in
order to ensure good air circulation.
■ The appliance may only be operated in rooms with an ambi-
ent temperature of 5 °C to 35 °C.
■ Use the appliance only in areas measuring a total of 20 m².
■ Clean the air filters before they become heavily soiled.
■ While draining the tube, ensure that it does not become
blocked and that the open end of the tube is positioned at a
lower level than the outlet aperture. The end of the tube must
be positioned above a drain.
■ Operate the appliance only with the integrated water tank
or with the tube installed.
■ Connect the earthing pin plug only to a properly installed,
easily accessible plug socket with protected contacts, the
voltage of which corresponds to the specifications on the
rating plate. The plug socket must remain easily accessible
even following connection.
■ Before cleaning, always disconnect the mains plug from the
mains power socket.
SLE 320 A2
GB│CY
│
7 ■
Initial operation
Consignment scope and carriage inspection
The appliance is supplied with the following components as standard:
▯ Dehumidifier
▯ Tube
▯ EU garden hose adapter
▯ These operating instructions
NOTE
►
Check the consignment for completeness and for signs of visible damage.
► If the consignment is incomplete or damaged due to defective packaging
or carriage, contact the Service hotline (see the chapter Service).
♦ Remove all packaging materials and all carriage braces from the appliance.
♦ Remove the film from the control panel.
Disposal of packaging materials
The packaging protects the appliance from damage during carriage. The
packaging materials have been selected in accordance with environmentally
congruent and disposal-specific parameters and are, therefore, recyclable.
Returning the packaging to the materials cycle conserves raw materials and
reduces the amount of waste that is generated. Dispose of packaging materials
that are no longer needed in accordance with applicable local regulations.
■ 8 │ GB
│
CY
SLE 320 A2
Appliance description
Air outlet valve
2
Carrying handle
3
Control panel
4
Grip recess for the water tank
5
Water tank
6
Rollers
7
Water level monitoring markers
8
Air inlet grille (removable)
9
Plastic filter
10
Carbon filter
11
Cable spool
12
Power cord
13
Drainage closure
14
Outlet
15
Securing brace
16
LED programmes
17
Display
18
TIMER LED
19
TANK FULL LED
20
OPERATION LED
21
STANDBY button
22
TIMER button
23
UP/DOWN arrow keys
24
MODE button
25
Tube
26
EU garden hose adapter
SLE 320 A2
GB│CY
│
9 ■
Before initial use
♦ Place the appliance on a flat, dry and solid surface.
♦ Allow the appliance to remain in the deployment position for approx.
30 minutes so that the coolant can pool.
♦ Check that the float, located on the right-hand side of the water tank
is able to move freely.
♦ Check whether the water tank
♦ Connect the mains plug into a mains power socket.
5
has been correctly inserted.
Electrical connection
CAUTION
►
Before connecting the appliance, compare the specifications for the
required input voltage on the rating plate with the voltage source designated for operation. These data must be congruent so that no damage is
sustained by the appliance.
► The power cable must always be easily accessible, so that the appliance
can be swiftly removed from the mains in the event of an emergency.
► Ascertain that the power cable is undamaged and that it is not routed over
hot surfaces and/or sharp edges, otherwise it will become damaged.
► Ensure that the power cable is not taut or kinked.
Guidelines for operation
■ Should the air in your living spaces consistently evince excess relative humidity,
the cause should be identified and addressed. (Sustained - year-round - venting
is generally inappropriate.)
■ The optimal ambient temperature for dehumidifying the air is 5 °C to 35 °C.
Using a dehumidifier at temperatures below 5 °C is redundant, as there is little
humidity in the air.
■ During operation, room temperature can increase by between 1 °C and 4 °C,
depending on the size of the room. This is normal.
5
,
Automatic defrosting
To ensure that the appliance does not ice up during sustained operation, it defrosts
automatically. This involves activation of dehumidification, with the motor running
at the highest setting. The ranges involved vary.
■ 10 │ GB
│
CY
SLE 320 A2
Handling and operation
In this section, you will receive important information pertaining to appliance
handling and operation.
Switching the appliance on/off
♦ Press the STANDBY button 21 to switch the appliance on. The OPERATION
20
LED
lights up.
♦ Press the STANDBY button
LED 20 goes out.
NOTE
►
The appliance starts in the mode last selected.
► After a power failure, if the appliance is disconnected from the mains, or
after switching off owing to the overheating guard, the appliance starts in
the mode last selected.
♦ If a timer has been programmed, the appliance switches off definitively
upon lapse of the time specified (1-24 hour/s).
♦ If the relative humidity value has been defined in the TARGET HUMIDITY
programme, the appliance switches off once the value has been attained.
If the value is exceeded, the appliance switches on again.
♦ The appliance switches off if the water tank
If wrongly positioned, or if the water tank
FULL LED
signal is emitted.
19
lights up when the appliance is switched on and an audible
21
to switch the appliance off. The OPERATION
5
is full or has been removed.
5
has been removed, the TANK
NOTE
► The water tank
condensate cannot be collected properly.
Air outlet valve
Always open the air outlet valve, regardless of the appliance’s respective programme. If the valve is not opened, the overheating guard switches the appliance off after some time for approx. 3 minutes.
SLE 320 A2
5
must be fully inserted in the appliance; otherwise, the
GB│CY
│
11 ■
Operating status displays
The various operating statuses are indicated by means of LEDs ( 16, 18, 19, 20 )
and the display
LED indicators
LED glowsMeaning
TANK FULL
TIMER
19
18
AIR CLEAN
DRY CLOTHES
TARGET HUMIDITY
AUTOMATIC
OPERATION
Display indicators
IndicatorMeaning
HIGH
MID
LOW
HIGH
MID
LOW
HIGH
MID
LOW
17
.
The water tank is full or is not inserted.
A switch-off time has been activated.
16
Selected programme
20
The appliance is switched on.
This indicator is consistently visible during operation.
It indicates the room's humidity range:
LOW:
below 65%
MEDIUM:
HIGH:
65% to 75%
over 75%
■ 12 │ GB
│
CY
SLE 320 A2
Selecting programmes
NOTE
► The values defined for relative humidity (rh) are recognised, allowing for a
deviation of approx. ±3%. This is necessary so that the appliance does not
constantly switch itself on and off.
■ The appliance has 4 distinct programmes.
■ You switch between the programmes by pressing the MODE button
■ The LED programme
AUTOMATIC MODE
The relative humidity (rh) to be attained is permanently set to 55%. The compressor
effects dehumidification until this value has been attained, and then switches off.
If relative humidity again increases, the compressor switches on again.
In this programme, the appliance works at 3 distinct levels of intensity:
– rh above 70%: The appliance dehumidifies at the highest level.– rh between 55% and 70%: The appliance dehumidifies at standard
intensity.
– rh below 55%: No dehumidification; only the fan continues to run.
NOTE
► The rh values specific to AUTOMATIC mode are not identical to the values
HIGH/MEDIUM/LOW on the display
Select this programme for sustained dehumidification at a comfortable relative
humidity of 55%.
16
before the active programme glows.
17
.
24
.
TARGET HUMIDITY
In the TARGET HUMIDITY programme, you can select relative humidity in 5%
increments between 30% and 80% by pressing the arrow keys
ance dehumidifies at a low level of intensity until the defined value has been attained, and then switches off. If relative humidity again increases, the compressor
switches on again.
– 30% – 80%: setting for the room’s desired relative humidity– CO: The appliance dehumidifies on a sustained basis.
Select this programme for sustained dehumidification or for dehumidification
specific to the value you have defined.
IndicatorMeaning
30 – 80, or CO
flashes for
5 seconds
SLE 320 A2
23
. The appli-
Adjust relative humidity during sustained operation.
Values between 30 and 80, or CO flashes for 5seconds
upon switching on the appliance.
CO: The appliance dehumidifies on a sustained basis.
GB│CY
│
13 ■
DRYING LAUNDRY
■ You use this programme to dry damp laundry or shoes faster. The appliance
dehumidifies at the highest level of intensity. Manipulate the air outlet valve
such that the air current is directed towards the articles of clothing to be dried.
AIR PURIFICATION
No dehumidification takes place in this programme. The air in the room is drawn
in via the filter in front of the air inlet aperture, where it is purified.
Timer
■ The timer can be combined with all 4 programmes.
■ One of 24 switch-off times, ranging from 1 to 24 hours, can be selected.
■ Once the time defined has elapsed, the appliance switches off definitively and
the timer is deactivated.
♦ Press the TIMER button
♦ Use the arrow keys
selected time flashes on the display
♦ In order to end timer activation prematurely, press TIMER
the appliance off by pressing STANDBY
IndicatorMeaning
1 - 24 flashes /
3 seconds
Timer for all programmes: These values (1 - 24 hours) flash for
5 seconds if you define a switch-off time using the arrow keys.
22
during operation. The TIMER LED 18 flashes.
23
to select a switch-off time of 1 to 24 hours. The
17
for 3 seconds and is then stored.
21
.
22
twice or switch
■ 14 │ GB
│
CY
SLE 320 A2
Water tank
■ The water tank 5 has a storage capacity of 7 litres.
■ The water level is indicated on the front of the water tank
■ The appliance may only be operated once the water tank
■ If the water tank
The appliance switches off after a few seconds. An alarm sounds for approx.
20 seconds. The TANK FULL LED 19 flashes until the tank has been emptied.
♦ To empty the water tank
then hold it by the carrying handle (see Figure 1).
55
5
is full, the TANK FULL LED 19 starts to flash.
5
, pull it out a little to the left and the right and
5
.
5
is inserted.
Fig. 1
SLE 320 A2
♦ Pour out the water and replace the water tank
5
.
GB│CY
│
15 ■
Tube drainage
In very damp rooms, it is often more appropriate for the water not to collect in
the water tank, but for it to be drained directly by means of a tube.You can use
the supplied hose
drainage system.
CAUTION
►
When draining via the hose, the appliance runs continuously. During hose
drainage, ensure that the hose is not kinked and that it runs downwards
over its entire length as the appliance does not have a pump for drainage.
► Check all connections in the system regularly for watertightness.
♦ Unscrew the closure
♦ Either connect the supplied hose
hose adapter 26 to the outlet 14 (see figs. 3 + 4).
♦ If you are using the EU garden hose adapter
the EU garden hose adapter 26 (see fig. 4).
♦
or the EU garden hose adapter 26 to set up a permanent
25
on the rear of the appliance (see fig. 2).
13
to the outlet 14 or screw the EU garden
25
, screw a garden hose onto
26
14
13
25
Fig. 2 Fig. 3 Fig. 4
CAUTION
► Screw the EU garden hose adapter
hand-tight only. Do not use a
26
wrench as this could damage the EU garden hose adapter 26.
NOTE
►
Depending on the garden hose system you use, you may need an additional
adapter. These are available from specialist stores.
■ 16 │ GB
│
CY
14
26
SLE 320 A2
♦ Pull the water tank 5 out of the appliance and remove the stopper which is
located in the lid of the water tank
(see fig. 5).
5
♦ Then insert the stopper into the outlet aperture for the water tank (see fig. 6).
5
Fig. 5 Fig. 6
♦ Replace the water tank 5 in the appliance.
♦ Set up the appliance such that the end of the hose is positioned over a
drain. The open end of the hose must be positioned lower than the appli-
ance‘s outlet (i.e. the hose must run downwards).
♦ Switch on the appliance as usual and select a programme.
♦ If you wish to drain into the water tank
again, switch off the appliance,
5
pull off the hose 25 or unscrew the EU garden hose adapter 26 together
with the garden hose.
♦ Screw the closure back onto the outlet
14
.
♦ Remove the stopper from the outlet for the water tank and replace it into the
lid of the water tank.
SLE 320 A2
GB│CY
│
17 ■
Cleaning
CAUTION
Potential appliance damage!
► Protect the appliance from moisture and from the ingress of fluids.
► To avoid irreparable damage to the appliance, never immerse it in water.
► Always remove the mains plug from the mains power socket before clean-
ing the appliance.
► Do not use aggressive or abrasive cleaning agents, as these may corrode
the surface of the casing.
► Do not clean the water tank
damaged.
♦ If required, wipe the casing with a slightly damp cloth.
♦ Remove the water tank
tank 5 thoroughly, both inside and out, before replacing it.
♦ In order to clean the inside of the water tank 5, you must remove the black
lid. To do this, release the carrying handle from the retainer while pressing
it out sideways. Ensure that the pins on the handle line up with the grooves
on the water container (see fig. 7).
5
in a dishwasher. Otherwise, it will be
5
and pour away the water; then dry the water
■ 18 │ GB
5
Fig. 7
♦ Now, remove the black lid from the water tank
♦ To insert, follow the reverse sequence.
♦ It is recommended that the water tank
weeks to prevent the build-up of mould and bacteria. To do this, fill the
water tank
repeatedly with lukewarm water. In addition, disinfection is recommended
following cleaning. To do this, use a standard, alcohol-based disinfecting
agent or high-proof alcohol. Both substances are completely harmless if
followed by repeated rinsing with lukewarm water.
│
CY
5
with lukewarm water, adding a standard detergent. Rinse
5
5
.
be cleaned regularly every two
SLE 320 A2
Cleaning and changing the filter
The performance of the appliance also depends upon how clean the filter is.
9
■ The plastic filter
■ The carbon filter
months.
NOTE
►
You can purchase new carbon filters in almost all shops selling household
goods. The carbon filter mats just need to be cut to size.
♦ Switch the appliance off and remove the mains plug.
♦ Remove the water tank
♦ To remove the air inlet grille
air inlet grille 8 must be pressed upwards slightly to allow release.
♦ Remove the air inlet grille
♦ To remove the plastic filter
plastic filter
♦ Now, remove the plastic filter
ance by pulling it downwards.
♦ The carbon filter
♦ Start by removing the plastic filter
fully out from under the retaining tabs in the plastic frame.
♦ Now remove the carbon filter 10.
♦ Wash down both filters with lukewarm water.
♦ Allow both filters to dry completely before re-inserting the filter in the
appliance.
♦ To insert, follow the reverse sequence.
should be washed every 2 weeks.
10
should be cleaned every 2 weeks and changed every 6
5
from the appliance.
8
, three plastic lugs located at the base of the
8
in a downwards motion.
9
9
must be pressed downwards slightly to allow release.
10
is also located behind the plastic filter 9.
, two plastic lugs located at the base of the
9
including the plastic frames from the appli-
9
from the plastic frame by lifting it care-
SLE 320 A2
10
9
8
GB│CY
│
19 ■
Protection against overheating
The appliance has an overheating guard.
■ The overheating guard switches the appliance off automatically if there is a risk
of overheating.
■ For approx. 3 minutes thereafter, the appliance cannot be re-started.
■ After approx 3 minutes, the appliance re-starts automatically.
■ Check whether external factors may have triggered the overheating guard.
(e.g. temperatures above 35 °C or a closed valve
obstructing the air outlet).
Storage
♦ Remove the mains plug from the mains power socket.
♦ Coil the power cord
plug to the power cord 12 using the securing brace 15 provided with
the cable.
♦ Empty the water tank
♦ Always store the appliance in an upright position and in a dry and dust-free
environment.
12
around the cable spool 11 and secure the mains
5
if not using the appliance for a prolonged period.
Troubleshooting
This section contains important information on fault identification and rectification.
Causes of malfunction and fault rectification
The following Table will help to identify and rectify minor faults:
FaultPossible causeRectification
Insert the mains plug into the mains
power socket.
Check the house's mains fuse.
Insert the water tank 5 correctly.
Empty the water tank
it.
The defrosting function is activated. This
is a normal feature of the appliance.
This is a normal feature of the appliance.
The appliance
will not switch
on.
The appliance
stops occasionally (the fan
switches off).
The mains plug is not plugged in.
The mains power socket is not
supplying power.
Safety stop due to the water
5
being missing or having
tank
been inserted incorrectly.
5
The water tank
Room temperature is below 15°C.
The humidity in the room is below
55%.
is full.
5
and re-insert
■ 20 │ GB
│
CY
SLE 320 A2
Loading...
+ 53 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.