Sherwood RD-705i Operating Instructions Manual

RD-705i

NETWORK AV RECEIVER

OPERATING INSTRUCTIONS

705i(A) cover_cover.qxp 2010-11-08 오후 4:31 페이지 1

ENGLISH

2

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings.
Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades
with one wider than the other.
A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not fit
into your outlet, consult an electrician for replacement of
the obsolete outlet.

10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.

11. Only use attachments/accessories specified by the
manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the
apparatus.
When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when
unused for long periods of time.

14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally,
or has been dropped.

PORTABLE CART WARNING

RD-705i(A)_ENG_101206_RD-705i(A)_ENG2010-12-06오후2:43페이지2

ENGLISH

3

Introduction

FOR YOUR SAFETY

CAUTION

: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

This symbol is intended to alert the user to the presence of
u

ninsulated "dangerous voltage" within the product's
enclosure that may be of sufficient magnitude to constitute
a

risk of electric shock to persons.

T

his symbol is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.

Caution regarding installation

Note : For heat dispersal, do not install this unit in a confined space such as a bookcase or similar enclosure.

: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).
N

O USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
P

ERSONNEL.

CAUTION

WARNING

Do not block ventilation openings or stack other equipment on the top.

O

N / STANDBY

A

UTO / MANUAL

S

URROUND

S

TEREO

V

IDEO

A

UDIO

S

OUNDINPUT

A

UDIO ASSIGNSPEAKER

O

N / OFF

T

ONE CH.LEVEL SETUP ENTER / MEMO BANDPRESETTUNE

P

HONES

SETUP MIC F.AUX

POWER

N

ETWORK AV RECEIVER

R

D-7

05i

B

luetooth IN

R

ETURN

M

AIN MENU

MASTER VOLUME

S

TANDBY

USB
5

V/1A

READ THIS BEFORE OPERATING YOUR UNIT

Note to CATV System Installer :

This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building, as
close to the point of cable entry as practical.

FCC INFORMATION

This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee
that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can
be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and
receiver.

• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV
technician for help.

Caution : Any changes or modifications in construction

of this device which are not expressly
approved by the party responsible for
compliance could void the user’s authority to
operate the equipment.

This Class B digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la Classe B est conforme à
la norme NMB-003 du Canada.

Units shipped to the U.S.A and CANADA are designed for
operation on 120 V AC only.
Safety precaution with use of a polarized AC plug.
However, some products may be supplied with a nonpolarized plug.

U.S.A

CANADA

120 V

• Leave a space around the unit for sufficient ventilation.

• Avoid installation in extremely hot or cold locations, or in an area
that is exposed to direct sunlight or heating equipment.

• Keep the unit free from moisture, water, and dust.

• Do not let foreign objects in the unit.

• The ventilation should not be impeded by covering the ventilation
openings with items, such as newspapers, table-cloths, curtains, etc.

• No naked flame sources, such as lighted candles, should be
placed on the unit.

• Please be care the environmental aspects of battery disposal.

• The unit shall not be exposed to dripping or splashing for use.

• No objects filled with liquids, such as vases, shall be placed on
the unit.

• Do not let insecticides, benzene, and thinner come in contact with
the set.

• Never disassemble or modify the unit in any way.

■Notes on the AC power cord and the wall outlet.

• The unit is not disconnected from the AC power source(mains) as
long as it is connected to the wall outlet, even if the unit has been
turned off.

• To completely disconnect this product from the mains, disconnect
the plug from the wall socket outlet.

• When setting up this product, make sure that the AC outlet you
are using is easily accessible.

• Disconnect the plug from the wall outlet when not using the unit
for long periods of time.

: To prevent electric shock, match wide blade of

plug to wide slot, fully insert.

: Pour éviter chocs électriques, introduire la lame la

plus large de la fiche dans la borne correspondante
de la prise et pousser jusqu’ au fond.

CAUTION

ATTENTION

RD-705i(A)_ENG_101206_RD-705i(A)_ENG2010-12-06오후2:43페이지3

ENGLISH

4

CONTENTS

IMPORTANT SAFETY INSTRUCTIONS | 2

Introduction

• READ THIS BEFORE OPERATING YOUR UNIT | 3

System Connections | 5

Front Panel Controls | 13

Remote Controls | 15

• REMOTE CONTROL OPERATION RANGE | 16

• LOADING BATTERIES | 16

Operations

• LISTENING TO A PROGRAM SOURCE | 17

• SURROUND SOUND | 19

• ENJOYING SURROUND SOUND | 21

• LISTENING TO RADIO BROADCASTS | 26

• LISTENING TO SIRIUS SATELLITE RADIO | 28

(SIRIUS Satellite Radio (only for North America))

• LISTENING TO INTERNET RADIO BROADCASTS, MUSIC FILES | 33

• RECORDING | 43

• OTHER FUNCTIONS | 44

• CONFIRMING THE HDMI FUNCTION | 45

System Setup | 46

• SETTING THE SYSTEM SETUP | 48

• SETTING THE INPUT SETUP | 50

• SETTING THE SPEAKER / ROOM EQ SETUP | 52

• SETTING THE CH LEVEL SETUP | 58

• SETTING THE MULTI ROOM SETUP | 60

• SETTING THE PARAMETER SETUP | 61

• SETTING THE HDMI SETUP | 63

Troubleshooting Guide | 65

Specifications | 66

RD-705i(A)_ENG_101206_RD-705i(A)_ENG2010-12-06오후2:43페이지4

ENGLISH

5

System Connections

• Please be certain that this unit is unplugged from the AC outlet before making any connections.

• Since different components often have different terminal names, carefully read the operating instructions of the component
connected.

• Be sure to observe the color coding when connecting audio, video and speaker cords.

• Make connections firmly and correctly. If not, it can cause loss of sound, noise or damage to the receiver.

C

OAX 2

(AUX)

C

OAX 1

(V2)

OPT 2
(CD)

O

PT 1

(

V1)

R

LRL RL

ASSIGNABLE

V

IDEO 3

VIDEO 2

V

IDEO 1

V

IDEO 1 AUXVIDEO 3

S

UBWOOFER

P

REOUT

R

OOM 2

RL

L

R

L

R

CD VIDEO 1

IN

IN

IN

I

N

OUT

OUT

VIDEO 1VIDEO 1

M

ONITOR
OUT

VIDEO

S

PEAKERS

ANTENNA

AUDIO

DIGITAL IN

H

DMI

M

ONITOR

OUT

FM 75

G

ND

AM
L

OOP

S

N.

A

VIS : RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR.

W

ARNING : SHOCK HAZARD-DO NOT OPEN.

P

OWER SOURCE

POWER CONSUMPTION

NETWORK AV RECEIVER

RD-705i

OUT

F

RONT

(

6 )

SURROUND

(6 )

CENTER

(6 )

S

URROUND BACK /

F

.HEIGHT / ROOM 2 / BiAMP

(

6 )

O

UT

VIDEO 2

(

iPod)

VIDEO 2

(iPod)

DIGILINK-i

120V 60Hz

2

.5 A

D

ESIGNED IN USA
M

ADE IN CHINA

C

lass 2 Wiring

S

IRIUS

M

anufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762;

6

,226,616; 6,487,535; 7,212,872; 7,333,929; 7,392,195; 7,272,567 & other U.S. and worldwide

p

atents issued & pending. DTS and the Symbol are registered trademarks & the DTS logos

a

re trademarks of DTS, Inc. © DTS, Inc. All Rights Reserved.

M

anufactured under license from Dolby Laboratories. Dolby, Pro Logic, and the double-D

s

ymbol are trademarks of Dolby Laboratories.

E308916 48W3

Audio

/

Video

Apparatus

U

SB

(WiFi)

5V / 1A

12 10 982 3

2 11 432 1 2 6 7 7, 8

5 11

1. CONNECTING ANTENNAS

ANTENNA

F

M 75

GND

AM
L

OOP

ANTENNA

FM 75

GND

A

M

LOOP

• Change the position of the FM indoor antenna until you get
the best reception of your favorite FM stations.

ANTENNA

FM 75

GND

AM

LOOP

• Place the AM loop antenna as far as possible from the receiver, TV set, speaker cords and the AC
input cord and set it to a direction for the best reception.

• If the reception is poor with the AM loop antenna, an AM outdoor antenna can be used in place of
the AM loop antenna.

• A 75Ω outdoor FM antenna may be used to further
improve the reception. D isconnect the indoor
antenna before replacing it with the outdoor one.

RD-705i(A)_ENG_101206_RD-705i(A)_ENG2010-12-06오후2:43페이지5

ENGLISH

6

OUT

VIDEO 1

MONITOR

OUT

VIDEO

HDMI

MONITOR
OUT

OUT

V

IDEO 2

VIDEO 1

VIDEO 1 AUXVIDEO 3

L

R

L

R

CD VIDEO 1

IN

IN

IN

I

N

OUT

VIDEO 1VIDEO 1

M

ONITOR

OUT

VIDEO

AUDIO

O

UT

VIDEO 2

(iPod)

VIDEO 2

(iPod)

2. CONNECTING VIDEO COMPONENTS

• The jacks of VIDEO 1 may also be connected to a DVD recorder or other digital video recording component.
For details, refer to the operating instructions of the component to be connected.

• The jacks of VIDEO 2/VIDEO 3 can also be connected to an additional video component such as a cable TV tuner or satellite

system.

• Connect the jacks of VIDEO 3 to the video component in the same way.

The VIDEO 3 INs can be connencted to an additional video component without (composite) video connection.

• There are (composite) VIDEO jacks for analog video connections and the HDMI connectors for digital video and audio

connections.

• For your reference, the excellence in picture quality is as follows : "HDMI” > "(composite) VIDEO".

■Notes :

• When recording video program sources through the (composite) VIDEO 1 OUT jack or viewing video program sources

through the (composite) MONITOR OUT jack, you must connect the (composite) VIDEO IN jack to the video playback
components such as BD player, DVD player, etc.

• You can connect Apple iPod to this receiver via Sherwood iPod dock. If Sherwood iPod dock is connected to DIGILINK-i jack

for system control, you should connect its video and audio jacks to the “VIDEO 2” jacks of this receiver. Because, when you
control your iPod with the unit’s remote control, the VIDEO 2/iPod is automatically selected as an input source and the
corresponding operation is performed.

RD-705i(A)_ENG_101206_RD-705i(A)_ENG2010-12-06오후2:43페이지6

ENGLISH

7

■HDMI (High Definition Multimedia Interface) connection : (*)

• You can connect the source component (DVD player, etc.) to the display component (TV, projector, etc.) through this receiver

with using a commercially available HDMI cord.

• The HDMI connection can carry uncompressed digital video signals and digital audio signals.

• The HDMI video stream signals (video signals) are theoretically compatible with DVI-D. When connecting to a TV monitor,

etc., equipped with DVI-D connector, it is possible to connect using a commercially available HDMI-DVI converter cord.

Since the HDMI-to-DVI connection cannot carry any audio signals, set the HDMI AUDIO OUT to AMP to hear the HDMI digital
audio signals on this receiver.(For details, refer to "When selecting the HDMI AUDIO OUT" on page 63.)

■Copyright protection system

• This unit supports HDCP (High-bandwidth Digital Contents Protection), technology to protect copyright of digital video signals

against illegal duplication. HDCP must also be supported on the components connected to this unit.

• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI licensing

LLC.

■Notes :

• For stable signal transfer, we recommend using HDMI cables that are a maximum of 5 meters in length.

• Among the components that support HDMI, some components can control other components via the HDMI connector.

For details on the HDMI function, refer to “CONFIRMING THE HDMI FUNCTION” on page 45 and “SETTING THE HDMI
SETUP” on page 63.

• The audio signals from the HDMI connector (including the sampling frequency and bit length) may be limited by the

component that is connected.

• The video signals will not be output properly if a component incompatible with HDCP is connected.

• If the resolutions of the video signals which are output from the MONITOR OUTs and your monitor TV are not matched, the

picture is not clear, natural or displayed. In this case, change the setting of the resolution on the source component (BD
player, etc.) to one which the monitor TV can handle. (For details, refer to the operating instructions of the source component.)

• When you want to enjoy only the picture on your TV, not the sound, you should set the HDMI AUDIO OUT to AMP not to

output the digital audio signal from the HDMI MONITOR OUT of this receiver. (For details, refer to "When selecting the HDMI
AUDIO OUT" on page 63.)

VIDEO 1 AUX

CD VIDEO 1

OUT

AUX Tape deck, MD player, etc.

CD player

3. CONNECTING AUDIO COMPONENTS

• The AUX INs can be connected to an additional audio component such as a tape deck, an MD player, etc.

• When recording audio signals, connect the AUDIO IN/OUT jacks of “VIDEO 1” to audio recording equipment such as a tape

deck, an MD recorder, etc.

Continued

RD-705i(A)_ENG_101206_RD-705i(A)_ENG2010-12-06오후2:43페이지7

ENGLISH

8

5. CONNECTING SUBWOOFER PREOUT

• To emphasize the deep bass sounds, connect a powered

subwoofer.

SUBWOOFER

P

REOUT

6. CONNECTING FOR SYSTEM CONTROL

• Connect this jack to the DIGILINK-i jack of Sherwood
iPod dock that allows you to control the iPod with the
unit’s remote control.

DIGILINK-i

4. CONNECTING DIGITAL INS

• The OPTICAL and the COAXIAL DIGITAL OUTs of the components

that are connected to this unit can be connected to these DIGITAL
INs.

• A digital input should be connected to the components such as a

CD player, DVD player, etc. capable of outputting DTS Digital
Surround, Dolby Digital or PCM format digital signals, etc.

• For details, refer to the operating instructions of the component

connected.

• When making the COAXIAL DIGITAL connection, be sure to use a

75Ω COAXIAL cord, not a conventional AUDIO cord.

• Some of the commercially available optical fiber cords cannot be

used for the equipment. If there is an optical fiber cord which cannot
be connected to your equipment, consult your dealer or nearest
service organization.

■Note :

• Be sure to make either a OPTICAL or a COAXIAL DIGITAL

connection on each component. (You don’t need to do both.)

■Digital input default settings

• If you connect the DIGITAL INs to your components, it is easier to do so following the default settings.

• If your DIGITAL connections are different from default settings, you should assign the DIGITAL INs you used with the “When

selecting the DIGITAL IN” procedure on page 51.

• The default settings are as follows :

OPTICAL IN1 : VIDEO 1, OPTICAL IN2 : CD, COAXIAL IN 1 : VIDEO 2/iPod, COAXIAL IN 2 : AUX

C

OAX 2

(AUX)

C

OAX 1

(

V2)

O

PT 2

(

CD)

OPT 1
(V1)

ASSIGNABLE

DIGITAL IN

RD-705i(A)_ENG_101206_RD-705i(A)_ENG2010-12-06오후2:43페이지8

ENGLISH

9

7. CONNECTING SPEAKERS

RLRL RL

SPEAKERS

F

RONT
(6 )

SURROUND

(6 )

CENTER

(6 )

S

URROUND BACK /

F.H EIGHT / ROOM 2 / BiAMP

(6 )

RLRL RL

SPEAKERS

FRONT

(6 )

SURROUND

(6 )

CENTER

(6 )

SURROUND BACK /

F.H EIGHT / ROOM 2 / BiAMP

(6 )

Class 2 Wiring

Class 2 Wiring

Surround back/

Front height/

ROOM 2 right

Surround back/
Front height/
ROOM 2 left

• Be sure to connect speakers firmly and correctly

according to the channel(left and right) and the
polarity(+ and -). If the connections are faulty, no sound
will be heard from the speakers, and if the polarity of
the speaker connection is incorrect, the sound will be
unnatural and lack bass.

• For installing the speakers, refer to "Speaker

placement" on page 10.

• After installing the speakers, first adjust the speaker

settings according to your environment and speaker
layout.
(For details, refer to "SETTING THE SPEAKER/ROOM
EQ SETUP" on page 52.)

※ The SURROUND BACK channels can be connected

to surround back speakers, front height speakers,
ROOM 2 speakers or bi-amp capable speakers as
follows.

• Depending on how to use the speakers, you should

assign the power amplifier correctly. (For details, refer
to “When selecting the AMP ASSIGN” on page 48.)

■Surround back speakers

• When using only one surround back speaker, you

should connect it to SURROUND BACK LEFT channel.

■Front height speakers

• When listening in Dolby Pro Logic IIz mode, connect

the front height speakers.

■ROOM 2 speakers

• For ROOM 2 playback, connect the ROOM 2

speakers. (For details, refer to “CONNECTING ROOM
2 OUT JACKS OR ROOM 2 SPEAKER TERMINALS”
on page 11.)

■Front Bi-Amp Connections.

• Some speakers are equipped with two sets of input

terminals, for bi-amplification.

• Connect the FRONT and the SURROUND BACK

channels to the bi-amp-capable speakers. (For details,
refer to the operating instructions of your bi-amp­capable speakers.)

■Note :

• Before making bi-amp connections, remove the short-

circuiting bars from the terminals of your speakers.

Caution :

• Be sure to use the speakers with the impedance of 6

ohms or above.

• Do not let the bare speaker wires touch each other or

any metal part of this unit. This could damage this unit
and/or the speakers.

• Never touch the speaker terminals while the AC input

cord is connected to the wall AC outlet. Doing so could
result in electric shocks.

RD-705i(A)_ENG_101206_RD-705i(A)_ENG2010-12-06오후2:43페이지9

ENGLISH

Ideal speaker placement varies depending on the size of
your room and the wall coverings, etc. The typical example
of speaker placement and recommendations are as follows :

■Front left and right speakers and center speaker

• Place the front speakers with their front surfaces as flush
with TV or monitor screen as possible.

• Place the center speaker between the front left and right
speakers and no further from the listening position than the
front speakers.

• Place each speaker so that sound is aimed at the location
of the listener’s ears when at the main listening position.

■Surround left and right speakers

• Place the surround speakers approximately 60 to 90 cm (2
to 3 feet) above the ear level of a seated listener on the
direct left and right of them or slightly behind.

■Surround back left and right speakers

• Place the surround back speakers at the back facing the
front at a narrower distance than front speakers.

• When using a single surround back speaker, place it at the
rear center facing the front at a slightly higher position (0 to
20 cm ) than the surround speakers.

• We recommend installing the surround back speaker(s) at
a slightly downward facing angle. This effectively prevents
the surround back channel signals from reflecting off the
TV or screen at the front center, resulting in interference
and making the sense of movement from the front to the
back less sharp.

■Subwoofer

• The subwoofer reproduces powerful deep bass sounds.

Place a subwoofer anywhere in the front as desired.

■Front height left and right speakers (Recomended for

Dolby Pro Logic IIz playback)

• Place the front height speakers at least 1 meter (3.3 feet)

directly above the front speakers.

■Notes :

• When using a conventional TV, to avoid interference with

the TV picture, use only magnetically shielded front
left and right and center speakers.

• To obtain the best surround effects, the speakers except

the subwoofer should be full range speakers.

Speaker placement

11 12

13

10

Continued

■

Connecting speaker wire

1. Strip away approx. 10 mm
(3/8 inch) of wire insulation,
then twist the wire ends
tight.

2. Loosen by turning the
speaker terminal counter­clockwise.

3. Insert the bare part of the
wire.

4. Tighten by turning it
clockwise.

1. TV or Screen

2. Front left speaker

3. Subwoofer

4. Center speaker

5. Front right speaker

6. Surround left speaker

7. Surround right speaker

8. Surround back left speaker

9. Surround back right speaker

10. Surround center speaker

11. Front height left speaker

12. Front height right speaker

13. Listening position

At least 1 m

Front height speaker

Point slightly
downward

• 5.1 channel speaker system :

- front(2,5), center(4), surround(6,7), subwoofer(3)

• 6.1 channel speaker system :

- 5.1 channel speaker system + surround center(10)

• 7.1 channel speaker system :

- 5.1 channel speaker system + surround back(8,9)

• 7.1 channel speaker system(for Dolby Pro Logic IIz
playback) :

- 5.1 channel speaker system + front height(11,12)

RD-705i(A)_ENG_101206_RD-705i(A)_ENG2010-12-06오후2:43페이지10

ENGLISH

11

• ROOM 2 playback feature allows you to play a different program source in another room as well as one source in the main
room at the same time.

• For ROOM 2 playback, connect the ROOM 2 OUT jacks to the amplifier installed in another room, or connect the ROOM 2
speaker terminals to the speakers.

• To drive the speakers connected to the ROOM 2 speaker terminals, you should assign the power amplifier to “ROOM 2”. (For
details, refer to “When selecting the AMP ASSIGN” on page 48.)

■Note :

• To minimize hum or noise, use high quality connection cords.

8. CONNECTING ROOM 2 OUT JACKS OR ROOM 2 SPEAKER TERMINALS

• To connect this unit to a broadband home network wirelessly to listen to internet radio broadcast, connect the supplied 11N
Wireless USB adapter to the USB connector either on the rear panel or on the front panel.

• This unit is equipped with an IEEE802.11n(2.4 GHz band only) wireless module, which also supports the 802.11 b/g
standards.

■Notes :

• For safe opertaion, turn the power off before connecting or disconnecting the supplied 11N Wireless USB adapter.

• After making a broadband internet connection, you should set the communication settings.
(For details, see “When selecting “Network”” on page 41.)

• When using a broadband internet connection, a contract with an internet service provider is required.
For more information, contact your nearest internet service provider.

• Refer to the operating instructions of the equipment because the connected equipment and connection method may differ
depending on your internet environment.

9. CONNECTING TO NETWORK

RL

SURROUND BACK /

F.H EIGHT / ROOM 2 / BiAMP

(6 )

ROOM 2

R

L

OUT

Another room(Room 2)

Class 2 Wiring

Router with

access point

USB

(WiFi)

5V / 1A

* An access point is a device that allows you to connect your home network wirelessly.

RD-705i(A)_ENG_101206_RD-705i(A)_ENG2010-12-06오후2:43페이지11

12

11. AC INPUT CORD

• Plug the cord into a wall AC outlet.

12. TERMINALS FOR UPGRADES

• These terminals may be used in the future to update the operating software so that it will be able to support new digital audio
formats, etc.

■Note :

• Programming for upgrades requires specialized programming knowledge and for that reason we recommend that it only be
done by qualified installers.

SIRIUS

• Connect the SIRIUS connector to the Sirius Connect
Home Tuner kit (sold separately).

• Position the Home Tuner antenna near a south-facing
window to receive the best signal.
When making connections, also refer to the operating
instructions of the SiriusConnect Home Tuner.

• To listen to SIRIUS Satellite Radio, refer to "SIRIUS
Satellite Radio (only for North America)" on page 28.

10. CONNECTING SIRIUS CONNECTOR (only for North America)

■Positioning the antenna

• For a consistent satellite signal, the antenna must be
positioned correctly. Use the following map to determine
which area you are in and position the antenna
accordingly.

• Area 1 : Point the antenna toward the sky in the east,
notrtheast, or southeast, either through a window or
outside.

• Area 2 : Point the antenna toward the sky in the north
or northeast, either through a window or outside.

• Area 3 : Point the antenna toward the sky in the north
or northwest, either through a window or outside.

• Area 4 : Point the antenna toward the sky in the west,
northwest, or southwest, either through a window or
outside.

• Area 5 : Put the antenna outside and point it straight
up. The antenna cannot be used indoors.

SiriusConnect Home Tuner

To a wall AC
outlet

ENGLISH

RD-705i(A)_ENG_101206_RD-705i(A)_ENG2010-12-06오후2:43페이지12

13

Front Panel Controls

ON / STANDBY

A

UTO / MANUAL

SURROUND

S

TEREO

VIDEO

A

UDIO

S

OUND

I

NPUT

A

UDIO ASSIGNSPEAKER

O

N / OFF

T

ONE CH.LEVEL SETUP ENTER / MEMO BANDPRESETTUNE

PHONES

S

ETUP MIC F.AUX

P

OWER

NETWORK AV RECEIVER R

D-7

05i

Bluetooth IN

R

ETURN

M

AIN MENU

M

ASTER VOLUME

S

TANDBY

U

SB

5

V/ 1A

681 2

9

10 11 13 1514 16 17 18 19 20 21 22 23 24 25

73 4 12 5

■FLUORESCENT DISPLAY

12 345678910 11 12

1. Input, frequency, volume level, surround
mode, operating information, etc.

2. Surround mode indicators

3. AUTO indicator

4. DIGITAL INPUT indicator

5. HDMI indicator

6. DIRECT indicator

7. ROOM 2 indicator

8. REPEAT indicator

9. SHUFFLE indicator

10. FAVORITE indicator

11. SIGNAL STRENGTH OF INTENET RADIO indicator

12. SLEEP indicator

1. POWER switch

2. STANDBY indicator

3. POWER ON/STANDBY button

4. REMOTE SENSOR

5. FLUORESCENT DISPLAY
For details, see below.

6. VIDEO INPUT SELECTOR button

7. AUDIO INPUT SELECTOR button

8. MASTER VOLUME knob

9. HEADPHONE jack

10. SETUP MIC jack
For details, see next page.

11. FRONT AUX IN jack
For details, see next page.

12. AUTO/MANUAL button

13. SURROUND MODE UP/DOWN(▶/◀) buttons

14. STEREO button

15. SPEAKER button

16. AUDIO ASSIGN button

17. TONE MODE button

18. CHANNEL LEVEL button

19. SETUP button

20. ENTER/MEMORY button

21. TUNING UP/DOWN(+/-),

CURSOR LEFT/RIGHT(◀/▶) buttons

22. PRESET UP/DOWN(+/-),

CURSOR UP/DOWN(▲/▼) buttons

23. BAND button

24. USB connector
For details, see next page.

25. Bluetooth IN connector
For details, see next page.

ENGLISH

RD-705i(A)_ENG_101206_RD-705i(A)_ENG2010-12-06오후2:43페이지13

ENGLISH

14

SETUP MIC

Microphone

• To use Auto Setup function, connect the supplied microphone to the SETUP MIC jack.(For details, refer to "When
selecting the AUTO SETUP" on page 52.)

■Notes:

• Because the microphone for Auto Setup is designed for use with this receiver, do not use a microphone other than
the one supplied with this receiver.

• After you have completed the auto setup procedure, disconnect the microphone.

■SETUP MIC JACK

F.AUX

• The FRONT AUX IN jack can be connected to additional audio components such as an MP3 player, etc.

■Note :

• When connecting this jack to an MP3 player, etc., you should use the stereo mini cord, not a mono mini cord.

■FRONT AUX IN JACK

Bluetooth IN

U

SB

5V /1A

• An USB memory device can be connected to the USB connector either
on the front panel or on the rear panel to listen to MP3 or WMA files
stored on it through this unit. (For details, refer to “When selecting
“music library”” on page 37.)

■Note :

• After USB playback, remove the USB memory device in the stop mode
or the standby mode.

■USB CONNETOR

■Bluetooth IN CONNECTOR

Bluetooth IN

USB

5V /1A

• If the Bluetooth IN connector is connected to Sherwood Audio Receiver

BT-R7(sold separately) with Bluetooth wireless technology, you can enjoy
music wirelessly with a music player featuring Bluetooth wireless
technology such as MP3 player, mobile phone, etc..
(For information on Sherwood Audio Receiver BT-R7, contact your dealer.)

• The Bluetooth word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by Sherwood Corporation is
under license. Other trademarks and trade names are those of their
respective owners.

■Note:

• For safe operation, turn the power off before connecting or disconnecting
the Audio Receiver BT-R7.

USB memory device

RD-705i(A)_ENG_101206_RD-705i(A)_ENG2010-12-06오후2:43페이지14

ENGLISH

15

Remote Controls

CURSOR CONTROL( , , , ),
ENTER buttons

ROOM 2 button

NETWORK CONTROL
(NETWORK, RATING ( ),
PAUSE( ), PLAY( ), STOP( ),
REPEAT( ), SHUFFLE( ),
BACKWARD SKIP( ),
FORWARK SKIP( )) buttons

RD-705i(A)_ENG_101206_RD-705i(A)_ENG2010-12-06오후2:43페이지15

ENGLISH

16

O

N / STANDBY

A

UTO / MANUAL

S

URROUND

S

TEREO

V

IDEO

AUDIO

S

OUND

INPUT

A

UDIO ASSIGNSPEAKER

O

N / OFF

T

ONE CH.LEVEL SETUP ENTER / MEMO BANDPRESETTUNE

PHONES

SETUP MIC F.AUX

POWER

N

ETWORK AV RECEIVER

R

D-7

05i

B

luetooth IN

R

ETURN

M

AIN MENU

M

ASTER VOLUME

S

TANDBY

U

SB

5

V/1A

LOADING BATTERIES

REMOTE CONTROL OPERATION RANGE

• Use the remote control unit within a range of about 7 meters (23
feet) and angles of up to 30 degrees aiming at the remote sensor.

• Remove the batteries when they are not used for a
long time.

• Do not use the rechargeable batteries (Ni-Cd type).

1. Remove the cover. 2. Load two batteries ("AAA" size, 1.5 V) matching

the polarity.

RD-705i(A)_ENG_101206_RD-705i(A)_ENG2010-12-06오후2:43페이지16

ENGLISH

Operations

LISTENING TO A PROGRAM SOURCE

Before operation

• Enter the standby mode.

• The STANDBY indicator lights up.
This means that the receiver is not
disconnected from the AC mains and a small
amount of current is retained to support the
operation readiness.

• To switch the power off, push the POWER
switch again.

• Then the power is cut off and the STANDBY
indicator goes off.

• Each time the POWER ON/STANDBY button on the front

panel is pressed, the receiver is turned on to enter the
operating mode or off to enter the standby mode.

• On the remote control, press the POWER ON button to

enter the operating mode or press the STANDBY button to
enter the standby mode.

POWER

ON / STANDBY

1. In the standby mode, turn the power on.

3. Select the desired input source.

17

■Note : Before operating this receiver, first set this unit as desired for optimum performance, doing the system setup

procedures. (For details, refer to "System Setup" on page 46.)

• Then “SPEAKER ON” is displayed and the sound can be

heard from the speakers connected to the speaker
terminals.

• When using the headphones for private listening, press the

SPEAKER button again to switch the speakers
off(“SPEAKER OFF” is displayed).

2. Switch the speakers on.

• Each time the “VIDEO” button on the front panel is
pressed, the input source changes as follows:
→ VIDEO 1 → V2/iPOD → VIDEO 3

• Each time the “AUDIO” button on the front panel is
pressed, the input source changes as follows:
→CD→AUX→TV*→F.AUX→BT→NET/USB→Tuner

(Frequency display)

* : Only when the HDMI CONTROL is set to ON, you can

hear the digital audio signals from TV via a HDMI cable.
(For details, refer to “When selecting the HDMI

CONTROL” on page 63.)

• When selecting NET/USB, refer to “LISTENING TO
INTERNET RADIO BROADCASTS, MUSIC FILES” on
page 33.

• Each time the BAND button(or the TUNER button on the
remote control) is pressed, the band changes as follows:

→FM STEREO →FM MONO →AM → SIRIUS

When an input source other than TV, NET/USB, tuner
is selected

AUDIO ASSIGN

RETURN

4. Select the digital or the analog input connected as desired.

• Each time this button is pressed, the corresponding input
is selected as follows:

→ OPTI.1 → OPTI.2 → COAX.1 → COAX.2 → ANALOG

■Notes :

• When VIDEO 1 ~ 3 is selected and the corresponding HDMI IN
is connected, the digital input cannot be selected depending on
the AUDIO MODE setting (“AUTO”, “HDMI”).

• When TV, NET/USB or tuner is selected as an input source, the
digital input cannot be selected.

• The selected digital input or analog input is automatically
assigned to the corresponding input source on the INPUT setup
menu. (For details, refer to “SETTING THE INPUT SETUP” on
page 50.)

• The sound from the component connected to the selected digital
input can be heard regardless of the selected input source.

• When the selected digital input is not connected, this unit
operates as follows depending on the AUDIO MODE setting.

* If the AUDIO MODE is set to “AUTO”, the “D” or “HDMI” flickers

and the analog input is automatically selected.

* If it is set to “DIGITAL” or “HDMI”, “OPTI.1”, etc or “HDMI1”, etc

flickers, meaning no sound is heard.

INPUT

BAND

AUDIO

VIDEO

• To hear the sound from the selected digital input, you
should set the AUDIO MODE correctly on the INPUT
SETUP menu. (For details, refer to “SETTING THE
INPUT SETUP” on page 50.)

RD-705i(A)_ENG_101206_RD-705i(A)_ENG2010-12-06오후2:43페이지17

ENGLISH

18

TONE

TUNE

• Each time these buttons are pressed, the tone mode is
selected as follows :

OFF : To listen to a program source without the

↕ tone effect.("DIR" lights up.)
ON : To adjust the tone for your taste.("DIR" goes off.)

• Each time these buttons are pressed, the tone is selected as
follows:

→ BASS ↔ TREBLE ↔ TONE: ON ←

■When the TONE is set to ON to adjust the tone

(bass and treble).

• The tone level can be adjusted within the range of -10 ~
+10 dB.

• In general, we recommend the bass and treble to be
adjusted to 0 dB (flat level).

• Extreme settings at high volume may damage your
speakers.

• If the tone display disappears, start from the step 9 again.

Adjusting the tone (bass and treble)

TO O

FF

NE :

FM MH P 0 1

-30

z.

50

87

• The tone mode is
displayed for several
seconds.

9. Enter the tone mode.

10. Press the CURSOR LEFT(◀)/RIGHT(▶)

buttons to select the desired tone mode.

11. Press the CURSOR UP(▲)/DOWN(▼) buttons

to select the desired tone.

12. Press the CURSOR LEFT(◀)/RIGHT(▶)

buttons to adjust the selected tone as desired.

PRESET

• Be sure to switch the speakers off.

• When listening to a DTS or Dolby Digital program source,
if the headphones are plugged in and the SPEAKER
button is set to off, it enters the 2CH downmix mode
automatically. (For details, refer to “2CH downmix
mode”on page 22.)

■Note:

• Be careful not to set the volume too high when using
headphones.

• When playing back the program sources with surround
sound, refer to “ENJOYING SURROUND SOUND” on
page 21.

• “MUTING” is displayed.

• To resume the previous sound level, press it again.

MASTER VOLUME

DOWN UP

MUTE

PHONES

5. Operate the selected component for playback.

6. Adjust the (overall) volume.

7. To mute the sound.

8. To listen with the headphones.

RD-705i(A)_ENG_101206_RD-705i(A)_ENG2010-12-06오후2:43페이지18

ENGLISH

19

SURROUND SOUND

• This receiver incorporates a sophisticated Digital Signal Processor that allows you to create optimum sound quality and sound
atmosphere in your personal Home Theater.

■DTS Digital Surround

DTS Digital Surround(also called simply DTS) supports up to

5.1 discrete channels and uses less compression for high

fidelity reproduction. Use it with DVDs and CDs bearing the
DTS logo.

■DTS-ES™ Discrete 6.1

This is a 6.1 channel discrete digital audio format adding a
surround back channel to the DTS digital surround sound. The
seven totally separate audio channels provide better spatial
imaging and 360 degrees sound localization, perfect for
sounds that pan across the surround channels. Use it with
DVDs bearing the DTS-ES logo, especially those with a DTS­ES Discrete sound track.

■DTS - ES™ Matrix 6.1

This is a 6.1 channel discrete digital audio format inserting a
surround back channel to the DTS digital surround sound
through matrix encoding. Use it with DVDs bearing the DTS­ES logo.

■DTS Neo : 6™ surround

DTS Neo : 6 is a matrix decoding technology for achieving

7.1 channel surround playback with 2 channel sources. It

includes "DTS Neo : 6 Cinema" suited for playing movies and
"DTS Neo : 6 Music" suited for playing music.

■DTS 96/24

This is high resolution DTS with a 96 kHz sampling rate and
24 bit resolution, providing superior fidelity. Use it with DVDs
bearing the DTS 96/24 logo.

■DTS-HD High Resolution Audio

Developed for use with HDTV, including the new video disc
formats Blu-ray and HD DVD, this is the latest multi-channel
audio format from DTS. It supports up to 7.1 channels with
96 kHz/24 bit sampling rate and signal resolution.

■DTS-HD Master Audio

Designed to take full advantage of the additional storage
space offered by the new Blu-ray and HD DVD disc formats,
this new DTS format offers up to 7.1 discrete channels of
uncompressed digital audio with 96 kHz/24 bit sampling rate
and signal resolution.

Manufactured under license under U.S. Patent #'s: 5,451,942;
5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535; 7,212,872;
7,333,929; 7,392,195; 7,272,567 & other U.S. and worldwide patents
issued & pending.
DTS is a registered trademark and the DTS logos, Symbol, DTS-HD
and DTS-HD Master Audio are trademarks of DTS, Inc.

ⓒ1996-2008 DTS, Inc. All Rights Reserved.

■Dolby Digital

Dolby Digital is the multi-channel digital signal format
developed by Dolby Laboratories. Discs bearing the Dolby
Digital logo includes the recording of up to 5.1 channels of
digital signals. This will put you right in the middle of the
action, just like being in a movie theater or concert hall.

■Dolby Digital EX

This mode expands 5.1-channel sources for 6.1/7.1 channel
playback. It's especially suited to Dolby Digital EX
soundtracks that include a matrix-encoded surround back
channel. The additional channel adds an extra dimension
and provides an enveloping surround sound experience,
perfect for rotating and fly-by sound effects.

■Dolby Digital Plus

Developed for use with HDTV, including the new video disc
formats Blu-ray and HD DVD, this is the latest multichannel
audio format from Dolby. It supports up to 7.1 channels with
48 kHz/24-bit sampling rate and signal resolution.

■Dolby TrueHD

Designed to take full advantage of the additional storage
space offered by the new Blu-ray and HD DVD disc formats,
this new Dolby format offers up to 7.1 discrete channels of
lossless audio performance with 96 kHz/24 bit sampling rate
and signal resolution.

■Dolby Pro Logic IIz

This mode adds front height channels to surround sound,
creating a 7.1 channel palyback for music, movies and video
games. Dolby Pro Logic IIz brings enhanced spatial effects,
added depth, and an overall airiness to listening experience.

■Dolby Pro Logic IIx

This mode expands any 2-channel source for 7.1-channel
playback. It provides a very natural and seamless surround
sound experience that fully envelopes the listener. As well as
music and movies,video games can also benefit from the
dramatic spatial effects and vivid imaging. It includes "Dolby
Pro Logic IIx Movie" suited for playing movies, "Dolby Pro
Logic IIx Music" suited for playing music and "Dolby Pro
Logic IIx Game" suited for playing games.

■Dolby Pro Logic II

If you are not using any surround back speakers, Dolby Pro
Logic II surround will be used instead of Dolby Pro Logic IIx
surround. It incudes Dolby Pro Logic II Movie, Dolby Pro
Logic II Music and Dolby Pro Logic II Game like Dolby Pro
Logic IIx surround.

■Dolby Pro Logic

Dolby Pro Logic is a specially encoded two channel surround
format which consists of four channels (front left, center, front
right and surround). Sources bearing the “ ”
provide the theater-like surround sound. The surround
channel is monaural, but is played through both surround
speakers.

Manufactured under license from Dolby Laboratories.
Dolby, Pro Logic, and the double-D symbol are registered
trademarks of Dolby Laboratories.

Surround modes

RD-705i(A)_ENG_101206_RD-705i(A)_ENG2010-12-06오후2:43페이지19

20

• The following modes apply conventional 2-channel signals
such as digital PCM or analog stereo signals to high
performance Digital Signal Processor to recreate sound
fields artificially. Select one of the 11 provided surround
modes according to the program source you want to play.

■Theater

This mode provides the effect of being in a theater when
watching a play.

■Movie

This mode provides the effect of being in a movie theater
when watching a movie.

■Hall

This mode provides the ambience of a concert hall for
classical music sources such as orchestral, chamber music
or an instrumental solo.

■Game

This mode is suitable for video games.

■Stadium

This mode provides the expansive sound field to achieve the
true stadium effect when watching baseball or soccer games.

■Classic

This mode provides the acoustic effects of a large concert
hall for classical music.

■Rock

This mode provides the ambience of a live concert for rock or
pop music.

■Acoustic

This mode suitable for acoustic music sources.

■Auto Volume Level Control

This mode automatically equalizes playback sound levels if
each sound level varies with the music source recorded in a
portable audio player.

■Virtual

This mode creates a virtual surround sound field through two
front speakers.

■Multi CH Stereo

This mode is designed for playing background music. The
front, surround and surround back channels create a stereo
image that encompasses the entire area.

For your reference, the sound from each channel can be reproduced according to the surround modes as follows:

(*): Depending on the subwoofer setting, the sound from the subwoofer channel may be reproduced.

• Depending on the speaker settings and the number of the encoded channels, etc., the sound from the corresponding channels
cannot be reproduced.(For details, refer to "SETTING THE SPEAKER / ROOM EQ SETUP" on page 52.)

Modes Channels FRONT L/R CENTER SURROUND L/R SURROUND BACK/ SUBWOOFER

FRONT HEIGHT L/R

DTS-HD HIGH RESOLUTION AUDIO/MASTER AUDIO OO O O/

—

O

DTS, DTS 96/24 OO O

—

O

DTS ES DISCRETE/MATRIX OO O O O

DTS NEO: 6 CINEMA/MUSIC OO O O

—

(*)

DOLBY DIGITAL PLUS / DOLBY TRUEHD OO O O/

—

O

DOLBY DIGITAL OO O

—

O

DOLBY DIGITAL EX OO O O O

DOLBY PRO LOGIC IIz OO O O O

DOLBY PRO LOGIC IIx MOVIE/MUSIC/GAME OO O O O

DOLBY PRO LOGIC II MOVIE/MUSIC/GAME OO O

—

O

(MULTI) PCM OO O O/

—

O

AUTO VOLUME LEVEL CONTROL/VIRTUAL O

—— — —

(*)

DOLBY PRO LOGIC OO O

——

(*)

Other Surrounds OO O O

—

(*)

STEREO O

—— — —

(*)

ENGLISH

RD-705i(A)_ENG_101206_RD-705i(A)_ENG2010-12-06오후2:43페이지20

21

ENJOYING SURROUND SOUND

• Each time this button is pressed, the mode changes as follows :
Auto surround mode : The optimum surround mode will be

automatically selected depending on the signal
format being input.

Manual surround mode : You can select the desired of different

surround modes selectable for the signal
being input with using the SURROUND
MODE UP/DOWN (>/<) buttons.

• Depending on surround back speaker setting(“SURR B”) or front height speaker setting(“F.HEIGHT”), some surround modes can be selected or
not as follows :
( ) : Possible only when “SURR B” is set to 2 channel(“L2”, “S2”). (Refer to “When selecting the SPEAKER CONFIGURATION” on page 55.)
[ ] : Possible only when “F.HEIGHT” is set to “LARGE” or “SMALL”.
< > : Possible only when “SURR B” or “F.HEIGHT” is set to “NO” and the digital signals from Dolby Digital 2ch source are played.
*

1

: When these sources are recorded at 192 kHz, only the corresponding mode(DOLBY DIGITAL+, DOLBY TrueHD, DTS-HD MASTER or

DTS-HD HI RES, PCM) can be selected.

*

2

: Stand for THEATER, MOVIE, HALL, GAME, STADIUM, CLASSIC, ROCK, ACOUSTIC, AUTO VOLUME LEVEL CONTROL, VIRTUAL,

MULTI CH STEREO.

■Notes :

• Even when the auto surround mode is selected and the same type of digital signal format is being input, the optimum
surround mode may vary depending on whether the speaker type is set to "NO" or not.

• When the auto surround mode is selected, the surround modes other than the optimum surround mode cannot be selected.

■When selecting the manual surround mode with pressing the AUTO/MANUAL button on the front panel

Select the desired surround mode.

■Note: Before surround playback, first perform the speaker setup procedure, etc. on the SETUP menu for optimum performance.

(For details, refer to "SETTING THE SPEAKER / ROOM EQ SETUP" on page 52.)

Depending on how to select a surround mode, select the auto surround mode or the manual surround mode.

(

"AT" lights up.)

("AT" goes off.)

• Each time the SURROUND MODE UP/ DOWN (>/<)
buttons are pressed, the surround mode changes
depending on the input signal format as follows :

A

UTO/MANUAL

SOUND

SURROUND

(DOLBY D+ +PLIIx MOVIE), DOLBY DIGITAL +, DOLBY D++ EX,
DOLBY D+ +PLIIx MUSIC, DSP Surround modes*

2

DOLBY DIGITAL+
(DOLBY HD+PLIIx MOVIE), DOLBY TrueHD, DOLBY HD+ EX,
DOLBY HD+ PLIIx MUSIC, DSP Surround modes*

2

DOLBY TrueHD
(DOLBY D+PLIIx MOVIE), DOLBY DIGITAL, DOLBY DIGITAL EX,
DOLBY D+PLIIx MUSIC, DSP Surround Modes*

2

(DTS-HD+PLIIx MOVIE), DTS-HD MASTER or DTS-HD HI RES,
DTS-HD+NEO:6, DTS-HD+PLIIx MUSIC, DSP Surround modes*

2

DTS-HD MASTER or DTS-HD HI RES

(DTS+PLIIx MOVIE), DTS ES DISCRETE, DTS+PLIIx MUSIC
(DTS+PLIIx MOVIE), DTS, DTS ES MATRIX, DTS+PLIIx MUSIC,
DSP Surround modes*

2

(DTS+PLIIx MOVIE), DTS or DTS 96/24, DTS+NEO:6, DTS+PLIIx
MUSIC, DSP Surround modes*

2

PCM
(PCM+PLIIx MOVIE), PCM, PCM+EX, PCM+PLIIx MUSIC,
DSP Surround modes*

2

DOLBY PRO LOGIC, DOLBY PLIIx MOVIE, DOLBY PLIIx MUSIC,
DOLBY PLIIx GAME, NEO:6 CINEMA, NEO:6 MUSIC, DSP
Surround modes*

2

DOLBY DIGITAL+,
[DOLBY D++PLIIz HEIGHT]

DOLBY TrueHD,
[DOLBY HD+PLIIz HEIGHT]

DOLBY DIGITAL,
[DOLBY D+PLIIz HEIGHT]
DTS-HD MASTER or DTS-HD HI RES,
[DTS-HD+ PLIIz HEIGHT]

DTS, [DTS+PLIIz HEIGHT]

DTS or DTS 96/24, [DTS+PLIIz HEIGHT]

PCM, [PCM+PLIIz HEIGHT]

DOLBY PRO LOGIC, DOLBY PLII MOVIE,
DOLBY PLII MUSIC, DOLBY PLII GAME,
NEO:6 CINEMA, NEO:6 MUSIC, DSP
Surround modes*

2

, <DOLBY DIGITAL>,

[DOLBY PLIIz HEIGHT]

Dolby Digital Plus 5.1 ch*

1

Dolby Digital Plus 7.1 ch
Dolby TrueHD 5.1 ch*

1

Dolby TrueHD 7.1 ch
Dolby Digital 5.1 ch,
Dolby Digital EX 6.1 ch
DTS-HD Master Audio 5.1 ch*

1

,

DTS-HD High Resolution Audio 5.1 ch*

1

DTS-HD Master Audio 7.1 ch,
DTS-HD High Resolution Audio 7.1 ch
DTS ES Discrete 6.1 ch
DTS ES Matrix 6.1 ch

DTS 5.1 ch,
DTS 96/24 5.1 ch
PCM 7.1 ch
PCM 5.1 ch*

1

Dolby Digital 2 ch,
PCM 2 ch ,
Analog 2 ch

Signal format being input

Selectable surround mode

“SURR B” : “L2”, “S2”, “L1”, “S1”

“SURR B”/”F.HEIGHT” “NO” or

“F.HEIGHT”:“LARGE”/”SMALL”

ENGLISH

RD-705i(A)_ENG_101206_RD-705i(A)_ENG2010-12-06오후2:43페이지21