Sherwood RD-6505 Operating Instructions Manual
RD-6505
AUDIO/VIDEO RECEIVER
OPERATING INSTRUCTIONS
6505(E) cover_cover.qxp 2010-05-24 오전 9:57 페이지 1
ENGLISH
2
:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
CAUTION
FOR YOUR SAFETY
Introduction
: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
This symbol is intended to alert the user to the
p
resence of uninsulated "dangerous voltage" within the
p
roduct's enclosure that may be of sufficient magnitude
t
o constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the
p
resence of important operating and maintenance
(servicing) instructions in the literature accompanying
the appliance.
Caution regarding installation
Note : For heat dispersal, do not install this unit in a confined space such as a bookcase or similar enclosure.
Do not block ventilation openings or stack other equipment on the top.
WARNING
Units shipped to Australia are designed for operation on 230 V AC only.
To ensure safe operation, the three-pin plug supplied must be inserted only into a standard three-pin power point
which is effectively earthed through the normal household wiring. Extension cords used with the equipment must
be three-core and be correctly wired to provide connection to earth.
Improper extension cords are a major cause of fatalities. The fact that the equipment operates satisfactorily
does not imply that the power point is earthed and that the installation is completely safe. For your safety, if
in any doubt about the effective earthing of the power point, consult a qualified electrician.
PAN-EUROPEAN UNIFIED VOLTAGE
All units are suitable for use on supplies 220-240 V AC.
EUROPE
AUSTRALIA
220 V
-
240 V
•
Leave a space around the unit for sufficient ventilation.
•
Avoid installation in extremely hot or cold locations, or in an area
that is exposed to direct sunlight or heating equipment.
•
Keep the unit free from moisture, water, and dust.
•
Do not let foreign objects in the unit.
•
The ventilation should not be impeded by covering the ventilation
openings with items, such as newspapers, table-cloths, curtains,
etc.
•
No naked flame sources, such as lighted candles, should be
placed on the unit.
•
Please be care the environmental aspects of battery disposal.
•
The unit shall not be exposed to dripping or splashing for use.
•
No objects filled with liquids, such as vases, shall be placed on
the unit.
• Do not let insecticides, benzene, and thinner come in contact
with the set
.
•
Never disassemble or modify the unit in any way.
■Notes on the AC power cord and the wall outlet.
•
The unit is not disconnected from the AC power source(mains)
as long as it is connected to the wall outlet, even if the unit has
been turned off.
•
To completely disconnect this product from the mains,
disconnect the plug from the wall socket outlet.
•
When setting up this product, make sure that the AC outlet you
are using is easily accessible.
•
Disconnect the plug from the wall outlet when not using the unit
for long periods of time.
Information for Users on Collection and Disposal of
Old Equipment and used Batteries
These symbols on the products, packaging, and/or
accompanying documents mean that used electrical
and electronic products and batteries should not be
mixed with general household waste. For proper
treatment, recovery and recycling of old products and
used batteries, please take them to applicable
collection points, in accordance with your national
legislation.
By disposing of these products and batteries correctly,
you will help to save valuable resources and prevent
any potential negative effects on human health and the
environment which could otherwise arise from
inappropriate waste handling.
For more information about collection and recycling of
old products and batteries, please contact your local
municipality, your waste diposal service or the point of
sale where you purchased the items.
[Information on Disposal in other Countries outside the
European Union]
These symbols are only valid in the European Union. If
you wish to discard these items, please contact your
local authorities or dealer and ask for the correct
method of diposal.
Note for the battery symbol (bottom two symbol examples):
The sign Pb below the symbol for batteries indicates
that this batteries contains lead.
READ THIS BEFORE OPERATING YOUR UNIT
RD-6505(E)_ENG_100517_RD-6505(E)_ENG 2010-05-24 오전 9:59 페이지 2
ENGLISH
3
CONTENTS
Introduction
• READ THIS BEFORE OPERATING YOUR UNIT | 2
System Connections | 4
Front Panel Controls | 10
Remote Controls | 12
• REMOTE CONTROL OPERATION RANGE | 13
• LOADING BATTERIES | 13
Operations
• LISTENING TO A PROGRAM SOURCE | 14
• SURROUND SOUND | 16
• ENJOYING SURROUND SOUND | 17
• LISTENING TO RADIO BROADCASTS | 22
• RECORDING | 24
• OTHER FUNCTIONS | 26
System Setup | 27
• SETTING THE SYSTEM | 29
• SETTING THE INPUT | 31
• SETTING THE SPEAKER SETUP | 32
• SETTING THE CH LEVEL | 36
• SETTING THE PARAMETER | 38
Troubleshooting Guide | 40
Specifications | 41
RD-6505(E)_ENG_100517_RD-6505(E)_ENG 2010-05-24 오전 9:59 페이지 3
4
System Connections
ENGLISH
• Please be certain that this unit is unplugged from the AC outlet before making any connections.
• Since different components often have different terminal names, carefully read the operating instructions of the
component connected.
• Be sure to observe the color coding when connecting audio, video and speaker cords.
• Make connections firmly and correctly. If not, it can cause loss of sound, noise or damage to the receiver.
N
1. CONNECTING ANTENNAS
• Change the position of the FM indoor antenna until you get
the best reception of your favorite FM stations.
• Place the AM loop antenna as far as possible from the receiver, TV set, speaker cords and the AC
input cord and set it to a direction for the best reception.
• If the reception is poor with the AM loop antenna, an AM outdoor antenna can be used in place of
the AM loop antenna.
• A 75Ω outdoor FM antenna may be used to further
impro ve the reception. Discon nect the indo or
antenna before replacing it with the outdoor one.
RD-6505(E)_ENG_100517_RD-6505(E)_ENG 2010-05-24 오전 9:59 페이지 4
5
ENGLISH
2. CONNECTING VIDEO COMPONENTS
• The jacks of VIDEO 1 may also be connected to a DVD recorder or other digital video recording component.
For details, refer to the operating instructions of the component to be connected.
• The jacks of VIDEO 2 can also be connected to an additional video component such as a cable TV tuner or satellite
system.
• There are (composite) VIDEO jacks for analog video connections and the HDMI connectors for digital video and audio
connections.
• For your reference, the excellence in picture quality is as follows : "HDMI” > "(composite) VIDEO" .
■Note :
• When recording video program sources through the (composite) VIDEO 1 OUT jack or viewing video program sources
through the (composite) MONITOR OUT jack, you must connect the (composite) VIDEO IN jack to the video playback
components such as BD player, DVD player, etc.
RD-6505(E)_ENG_100517_RD-6505(E)_ENG 2010-05-24 오전 9:59 페이지 5
6
ENGLISH
■HDMI (High Definition Multimedia Interface) connection : (*)
• You can connect the source component (DVD player, etc.) to the display component (TV, projector, etc.) through this
receiver with using a commercially available HDMI cord.
• The HDMI connection can carry uncompressed digital video signals and digital audio signals.
• The HDMI video stream signals (video signals) are theoretically compatible with DVI-D. When connecting to a TV
monitor, etc., equipped with DVI-D connector, it is possible to connect using a commercially available HDMI-DVI
converter cord.
Since the HDMI-to-DVI connection cannot carry any audio signals, set the HDMI to OFF to hear the HDMI digital audio
signals on this receiver.(For details, refer to "When selecting the HDMI" on page 30.)
■Copyright protection system
• This unit supports HDCP (High-bandwidth Digital Contents Protection), technology to protect copyright of digital video
signals against illegal duplication. HDCP must also be supported on the components connected to this unit.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
licensing LLC.
■Notes :
• For stable signal transfer, we recommend using HDMI cords that are a maximum of 5 meters in length.
• Among the components that support HDMI, some components can control other components via the HDMI connector.
However, this unit cannot be controlled by another component via the HDMI connector.
• The audio signals from the HDMI connector (including the sampling frequency and bit length) may be limited by the
component that is connected.
• The video signals will not be output properly if a component incompatible with HDCP is connected.
• If the resolutions of the video signals which are output from the MONITOR OUTs and your monitor TV are not
matched, the picture is not clear, natural or displayed. In this case, change the setting of the resolution on the source
component (BD player, etc.) to one which the monitor TV can handle. (For details, refer to the operating instructions of
the source component.)
• When you want to enjoy only the picture on your TV, not the sound, you should set the HDMI to OFF not to output the
digital audio signal from the HDMI MONITOR OUT of this receiver. (For details, refer to "When selecting the HDMI" on
page 30.)
CD player, BD player, Video game player, etc.
3. CONNECTING AUDIO COMPONENTS
• The TAPE IN/OUT jacks can be connected to audio recording equipment such as a tape deck, an MD recorder, etc.
• The CD INs can be connected to an additional video component without analog video jacks.
Continued
RD-6505(E)_ENG_100517_RD-6505(E)_ENG 2010-05-24 오전 9:59 페이지 6
7
ENGLISH
5. CONNECTING SUBWOOFER PRE OUT
• To emphasize the deep bass sounds, connect a powered
subwoofer.
4. CONNECTING DIGITAL INS
• The OPTICAL and the COAXIAL DIGITAL OUTs of the
components that are connected to CD and VIDEO 1~VIDEO 2
of this unit can be connected to these DIGITAL INs.
• A digital input should be connected to the components such as
a CD player, DVD player, etc. capable of outputting DTS Digital
Surround, Dolby Digital or PCM format digital signals, etc.
• For details, refer to the operating instructions of the component
connected.
• When making the COAXIAL DIGITAL connection, be sure to
use a 75Ω COAXIAL cord, not a conventional AUDIO cord.
• Some of the commercially available optical fiber cords cannot
be used for the equipment. If there is an optical fiber cord which
cannot be connected to your equipment, consult your dealer or
nearest service organization.
■Note :
• Be sure to make either a OPTICAL or a COAXIAL DIGITAL connection on each component.
(You don’t need to do both.)
■Digital input default settings
• If you connect the DIGITAL INs to your components, it is easier to do so following the default settings.
• If your DIGITAL connections are different from default settings, you should assign the DIGITAL INs you used with the
“When selecting the DIGITAL IN” procedure on page 31.
• The default settings are as follows : OPTICAL IN : VIDEO 1, COAX-1 IN : VIDEO 2, COAX-2 IN : CD
RD-6505(E)_ENG_100517_RD-6505(E)_ENG 2010-05-24 오전 9:59 페이지 7
ENGLISH
8
6. CONNECTING SPEAKERS
• Be sure to connect speakers firmly and correctly
according to the channel(left and right) and the polarity(+
and -). If the connections are faulty, no sound will be
heard from the speakers, and if the polarity of the speaker
connection is incorrect, the sound will be unnatural and
lack bass.
• For installing the speakers, refer to "Speaker placement"
on page 9.
• After installing the speakers, first adjust the speaker
settings according to your environment and speaker
layout.
(For details, refer to "SETTING THE SPEAKER SETUP"
on page 32.)
Caution :
• Be sure to use the speakers with the impedance of 6
ohms or above.
• Do not let the bare speaker wires touch each other or any
metal part of this unit. This could damage this unit and/or
the speakers.
• Never touch the speaker terminals while the AC input
cord is connected to the wall AC outlet. Doing so could
result in electric shocks.
■Connecting speaker wire
1. Strip away approx. 10 mm
(3/8 inch) of wire insulation,
then twist the wire ends
tight.
2. Lossen by turning the
speaker terminal counterclockwise.
3. Insert the bare part of the
wire.
4. Tighten by turning it
clockwise.
7. AC INPUT CORD
• Plug the cord into a wall AC outlet.
RD-6505(E)_ENG_100517_RD-6505(E)_ENG 2010-05-24 오전 9:59 페이지 8
ENGLISH
9
Ideal speaker placement varies depending on the size of your
room and the wall coverings, etc. The typical example of
speaker placement and recommendations are as follows :
■Front left and right speakers and center speaker
• Place the front speakers with their front surfaces as flush
with TV or monitor screen as possible.
• Place the center speaker between the front left and right
speakers and no further from the listening position than the
front speakers.
• Place each speaker so that sound is aimed at the location of
the listener’s ears when at the main listening position.
■Surround left and right speakers
• Place the surround speakers approximately 1 meter (40
inches) above the ear level of a seated listener on the direct
left and right of them or slightly behind.
■Subwoofer
• The subwoofer reproduces powerful deep bass sounds.
Place a subwoofer anywhere in the front as desired.
■Notes :
• When using a conventional TV, to avoid interference with the
TV picture, use only magnetically shielded front left and right
and center speakers.
• To obtain the best surround effects, the speakers except the
subwoofer should be full range speakers.
Speaker placement
1. TV or screen
2. Front left speaker
3. Front right speaker
4. Center speaker
5. Subwoofer
6. Surround left speaker
7. Surround right speaker
RD-6505(E)_ENG_100517_RD-6505(E)_ENG 2010-05-24 오전 9:59 페이지 9
Front Panel Controls
6
8
13
12
1
2
9
10 14 15 16 17 18 19 20 21 22 23
73 4 11 5
ENGLISH
■FLUORESCENT DISPLAY
10 9
1. Input, frequency, volume level, operating
information, etc.
2. Surround mode indicators
3. AUTO indicator
4. DIGITAL INPUT indicator
5. DIRECT indicator
6. Preset number, sleep time display
7. MEMORY indicator
8. PRESET indicator
9. SLEEP indicator
10. TUNED indicator
11. STEREO indicator
12. HDMI indicators
10
1. POWER switch
2. STANDBY indicator
3. POWER ON/STANDBY button
4. REMOTE SENSOR
5. FLUORESCENT DISPLAY
For details, see below.
6. VIDEO INPUT SELECTOR button
7. AUDIO INPUT SELECTOR button
8. MASTER VOLUME knob
9. HEADPHONE jack
10. AUX 1, 2 IN jacks
For details, see next page.
11. AUTO/MANUAL button
12. SURROUND MODE UP/DOWN(▶/◀) buttons
13. STEREO button
14. SPEAKER button
15. AUDIO ASSIGN button
16. TONE MODE button
17. CHANNEL LEVEL button
18. SETUP button
19. ENTER/MEMORY button
20. TUNING UP/DOWN(+/-),
CURSOR LEFT/RIGHT(◀/▶) buttons
21. PRESET UP/DOWN(+/-),
CURSOR UP/DOWN(▲/▼) buttons
22. BAND button
23. VIDEO 3 IN jacks
For details, see next page.
RD-6505(E)_ENG_100517_RD-6505(E)_ENG 2010-05-24 오전 9:59 페이지 10
11
ENGLISH
• The AUX 1, 2 IN jacks can be connected to additional audio components such as an MP3 player, etc.
■Note :
• When connecting these jacks to an MP3 player, etc., you should use the stereo mini cord, not a mono mini
cord.
■AUX IN JACK
■VIDEO 3 IN JACKS
VIDEO 3
• The VIDEO 3 IN jacks may be also connected to an additional video
component such as a camcorder, a video game player, etc.
RD-6505(E)_ENG_100517_RD-6505(E)_ENG 2010-05-24 오전 9:59 페이지 11
ENGLISH
12
Remote Controls
CURSOR CONTROL( , , , ),
ENTER buttons
RD-6505(E)_ENG_100517_RD-6505(E)_ENG 2010-05-24 오전 9:59 페이지 12
ENGLISH13ENGLISH
O
NOFF
LOADING BATTERIES
REMOTE CONTROL OPERATION RANGE
• Use the remote control unit within a range of about 7 meters (23
feet) and angles of up to 30 degrees aiming at the remote
sensor.
• Remove the batteries when they are not used for a
long time.
• Do not use the rechargeable batteries (Ni-Cd type).
1. Remove the cover. 2. Load two batteries ("AAA" size, 1.5 V) matching
the polarity.
RD-6505(E)_ENG_100517_RD-6505(E)_ENG 2010-05-24 오전 9:59 페이지 13
Loading...