LINE LASER PLBS 2 A1
LINE LASER
Translation of the original instructions
ČIAROVÝ LASER
Preklad originálneho návodu na obsluhu
IAN 277698
LINIOVÝ LASER
Překlad originálního provozního návodu
LINIENLASER
Originalbetriebsanleitung
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of
the device.
Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.
Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen
Funktionen des Gerätes vertraut.
GB Translation of the original instructions Page 1
CZ Překlad originálního provozního návodu Strana 11
SK Preklad originálneho návodu na obsluhu Strana 21
DE / AT / CH Originalbetriebsanleitung Seite 31
Contents
Introduction ......................................................2
Intended use ................................................................ 2
Features ................................................................... 2
Package contents ............................................................ 2
Technical details ............................................................. 2
Safety information ................................................3
Safety in the workplace ....................................................... 3
Electrical safety ............................................................. 3
Personal safety and rules for working with lasers .................................... 3
Appliance use and handling ...................................................4
Battery use and care ......................................................... 4
Appliance-specific safety instructions ............................................. 5
Before use .......................................................5
Inserting/replacing the batteries ................................................ 5
Using the protective cover/wall bracket ........................................... 5
Getting started .............................................................. 6
Operation .......................................................6
Switching the line laser on and off ............................................... 6
Aligning the line laser ......................................................... 6
Using the drill dust collector ....................................................6
Emptying the drill dust collector ................................................. 6
Appliance suction function ..................................................... 7
Detaching the appliance ...................................................... 7
Troubleshooting ..................................................7
Maintenance and cleaning ..........................................8
Storage .........................................................8
Disposal .........................................................8
Kompernass Handels GmbH warranty ...............................8
Service .................................................................... 9
Importer ................................................................... 9
PLBS 2 A1
GB
│
1 ■
LINE LASER PLBS 2 A1
Introduction
Congratulations on the purchase of your
new appliance. You have selected a high-
quality product. The operating instructions
are part of this product. They contain important
information about safety, usage and disposal.
Before using the product, please familiarise yourself
with all operating and safety instructions. Use the
product only as described and for the range of
applications specified. Please also pass these operating instructions on to any future owner.
Intended use
This line laser with a drill dust collector is a batteryoperated appliance that uses vacuum technology
to create a suction mounting on standard interior
wall surfaces. The appliance can be used to project
a laser line onto a wall and collect the drill dust
created when drilling a hole of up to 10mm in
diameter. Do not use the appliance for overhead
work. Any other usage of or modification to the
appliance is deemed to be improper and carries a
significant risk of accidents. The manufacturer accepts no responsibility for damage(s) attributable
to misuse. The appliance is not intended for commercial use.
Features
Line laser
Horizontal level
Vertical level
ON/OFF switch for line laser
Vacuum button
Battery compartment vacuum pump
Drill dust collector/cover for drill dust collector
Protective plate/drill opening
Battery compartment for line laser
Vacuum pump seal
Release (drill dust collector)
ON/OFF switch for vacuum pump
Seal (drill dust collector)
Protective cover/wall bracket
Tab/centring rib
Package contents
1 line laser PLBS 2 A1
2 x 1.5 V AA batteries
3 x 1.5 V LR44 batteries
1 set of operating instructions
Technical details
Line laser:
Laser wavelength: 650 nm
Laser output: < 1 mW
Laser class: 2
Batteries: 3 x 1.5 V
(direct current)
, type LR44
■ 2
│
GB
Levels (horizontal and vertical)
Accuracy: 0.3°
Drill dust collector:
Max. drill diameter: 10 mm
Vacuum pump:
Battery: 2 x 1.5 V
(direct current)
, type AA
PLBS 2 A1
Safety information
WARNING!
► Read all safety warnings and all instructions.
Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious
injury.
WARNING!
■ Do not allow children to play with packaging
materials. There is a risk of suffocation.
NOTE
► Check the package for completeness and
signs of visible damage.
► If the delivery is incomplete or damage has
occurred as a result of defective packaging
or during transport, contact the Service
hotline (see section Service).
Save all warnings and instructions for future
reference.
Do not remove any identification marks or
labels from the appliance.
Safety in the workplace
■ Do not work with the appliance in areas where
there is a risk of explosions, or in the presence
of flammable liquids, gases or dusts.
■ Keep children and bystanders away while oper-
ating the appliance. Distractions can cause you
to lose control.
■ Observe all safety instructions, guidelines, work
safety and accident prevention regulations
relevant to your activity and workplace.
Electrical safety
■ Do not use this appliance in wet or moist environ-
ments.
■ Remove the batteries if you do not intend to use
the appliance for a long time.
Personal safety and rules for
working with lasers
■ Stay alert, watch what you are doing and use
common sense when operating the appliance.
Do not use the appliance while you are tired or
under the influence of drugs, alcohol or medication. A moment of inattention while operating
the appliance may result in serious personal
injury.
■ Caution! If operating and adjustment equipment
or procedures other than those specified here
are used, this may result in hazardous radiation
exposure.
■ A laser is an extremely intensive beam of light.
Improper use can lead to severe and permanent
injuries to the eyes and the retinas.
■ Do not aim the laser at people or animals!
■ Do not aim the laser at reflective surfaces. These
can deflect the laser beam and put people at
risk.
■ Do not work with the appliance at eye level.
■ Never look into the direct or reflected beam.
■ If the beam hits your eye, close your eyes im-
mediately and turn your head away from the
beam.
■ Do not use any optical instruments such as
magnifying glasses, binoculars, spectacles or
other optical lenses to observe the source of the
beam or to deflect the laser.
■ Manipulations (modifications) to the direction
of the laser are not permitted.
■ Store these operating instructions safely and
pass them on to any future owner of the laser
appliance.
■ Keep out of reach of children.
PLBS 2 A1
GB
│
3 ■
■ Do not allow persons unfamiliar with the appli-
ance or these instructions to operate the appliance. This appliance is not a toy and can be
dangerous in hands of inexperienced users.
■ Avoid any abnormal posture. Keep proper
footing and balance at all times. This enables
better control of the appliance in unexpected
situations.
There are warning labels by the laser discharge
opening and on the underside of the appliance
which draw attention to the dangers. To ensure
proper recognition of the potential dangers, these
warning labels may not be removed or defaced.
WARNING! Protect yourself from
laser radiation!
Appliance use and handling
■ No parts of this appliance need to be serviced
by the user. Do not dismantle the appliance.
■ Do not drop the appliance and do not use
force.
■ Do not expose the appliance to corrosive sub-
stances.
■ Check the appliance and accessories for dam-
age before each use.
■ Do not use any damaged parts. Replace dam-
aged parts only with replacement parts that are
equal to the original in function and quality.
■ Keep the appliance out of the reach of children.
■ Use the appliance, the accessories, etc. in
accordance with proper use and these instructions. Take into account the operating conditions
and the task to be performed. The use of electrical appliances for purposes other than those
intended can result in hazardous situations.
■ Keep the appliance away from electromagnetic
sources such as induction cookers or electric
welding machines. Avoid static charges and
also excessively high or low ambient temperatures. They can damage the appliance.
■ Treat the appliance with care. Check for mis-
alignment or binding of moving parts, breakage
of parts and any other damage that may impair
the appliance's operation. If damaged, have
the power tool repaired before use. Many accidents are caused by poorly maintained or
defective appliances.
Battery use and care
Please note the following safety instructions when
handling the batteries. Batteries can leak or explode. The poisonous or caustic substances they
contain may leak out. This can cause significant
property damage, personal injury or damage to
health.
■ Never try to charge non-rechargeable batteries.
There is a risk of explosion and damage due to
leaking acids.
■ Use only the supplied batteries with the electrical
appliances. The use of other battery units may
lead to a risk of injury or fire. Do not use any
other types of batteries and do not use any other
power sources.
■ When they are not being used, store batteries
away from paper clips, coins, keys, nails, screws
or other small metal objects that could cause
the contacts to be bridged. Short-circuiting the
contacts of a battery may result in burns and/
or fire.
■ Do not use batteries that are leaking, discol-
oured, deformed or damaged in any other way.
■ Leaking or damaged batteries must be properly
disposed of in compliance with the usual precautions (protective gloves).
■ 4
│
GB
PLBS 2 A1
■ Do not open, dismantle, pierce, modify or throw
batteries and avoid unnecessary impacts.
■ Do not expose batteries to naked flames or
temperatures of above 50°C. Do not store batteries in hot locations and do not expose them
to direct sunlight.
■ Never immerse batteries in water or other liq-
uids.
■ Never place batteries in a microwave or high-
or low-pressure container.
■ Improper use may cause fluid to leak out of the
battery. If this happens, avoid contact with the
fluid. If contact occurs, flush the affected area
with water. Seek additional medical help if any
of the fluid gets into your eyes. Leaking battery
fluid can cause skin irritations or burns.
■ Incorrect use can cause vapours to escape that
can cause damage to health and respiratory
irritation. Ventilate the area immediately with
fresh air and obtain medical advice.
■ Incorrect handling can lead to a short-circuit or
an explosion!
■ Dispose of used batteries and defective appli-
ances in compliance with legal requirements.
Appliance-specific safety instructions
■ Keep the appliance away from wet or dampness.
Water getting into the appliance may lead to
an electric shock.
■ Do not work with this appliance in water or
other liquids.
■ Keep firm hold of the appliance and do not
drop it.
■ Avoid unintended switching on. Check that the
appliance is switched off when you insert a battery. Inserting batteries into the appliance while
it is switched on can cause accidents.
■ Do not block off the openings on the appliance.
Before use
Inserting/replacing the batteries
Vacuum pump
♦ To insert batteries, open the battery compart-
ment
by turning the cover anticlockwise and
removing it.
♦ Insert the supplied batteries or two equivalent
AA batteries. Observe correct polarity when
inserting batteries to avoid damage!
♦ Replace the cover and close it by turning it in
a clockwise direction until it clicks firmly into
place.
Line laser
♦ To insert the batteries, first remove the appli-
ance from the protective cover
♦ Open the battery compartment cover
underside of the line laser and remove it.
♦ Insert the supplied button cells or three equiva-
lent type LR44 button cells. Observe correct
polarity when inserting batteries to avoid damage.
♦ Replace the battery compartment cover
close it so that it clicks firmly into place.
Using the protective cover/wall
bracket
The protective cover is intended primarily to
protect the soft seals from damage when the
appliance is not in use.
♦ After use, always replace the protective cover
♦ You can attach the protective cover
determined attachment point on the wall with a
screw and use it as a wall bracket.
.
on the
and
to a pre-
.
PLBS 2 A1
GB
│
5 ■
Getting started
■ After inserting the batteries, the appliance is
ready for use.
■ Remove the protective cover/wall bracket
from the appliance.
■ Fully grip the appliance with one or, ideally,
both hands. The appliance is suitable for either
hand.
Operation
CAUTION!
► Use the appliance only for its intended use.
► Check the appliance for damage before use.
Do not use the appliance if its operational
safety cannot be guaranteed.
Switching the line laser on and off
♦ To switch the line laser on and off, press the
ON/OFF switch .
■ To make the levels
are illuminated.
♦ Switch the laser off again by pressing the
ON/OFF switch
Aligning the line laser
♦ Align the appliance using the horizontal and
vertical levels
the appliance. Centre the air bubble in one of
the levels between the two marking lines.
♦ For diagonal alignment of the laser, mark two
points in the desired alignment and line up the
laser with these markings.
♦ Switch on the vacuum pump (see section
Appliance suction function).
easier to read, these
.
by changing the tilt angle of
♦ To use the line laser
tion, you can release it from the mount by pulling
it in a horizontal direction.
♦ Replace the line laser on the guide and push it
in the direction of the battery compartment
until it clicks audibly into place.
without the suction func-
Using the drill dust collector
♦ Mark the spot on the wall where you want to
drill the holes.
♦ Push the loaded drill through the opening on
the protective plate
other side of the seal .
♦ Put the tip of the drill bit onto the marking.
♦ Hold the drill vertically to the wall.
♦ Push the drill dust collector
wall so that the seals lie up against the
wall.
NOTE
► To ensure that the drill dust collector
the dusts optimally, it should always be
aligned vertically.
♦ Switch on the vacuum pump (see section
Appliance suction function).
♦ Hold the drill firmly in both hands and follow the
manufacturer's operating and safety instructions.
♦ Use only suitable drills up to a max. 10 mm in
diameter.
♦ Wear your personal protective equipment
(safety goggles)!
♦ Pull the drill out of the drill dust collector
before you switch off the vacuum pump.
until it comes out of the
Emptying the drill dust collector
♦ Point the drill dust collector downwards.
Press the release buttons together on both
sides between your thumb and index finger and
swing the cover of the drill dust collector
upwards.
♦ Empty the drill dust collector
up against the
collects
.
■ 6
│
GB
PLBS 2 A1
♦ Place the outer tab of the cover back on the
centring rib of the cover.
♦ Swing the cover back until the release buttons
click audibly into place on both sides.
♦ Ensure that the cover is firmly in place on the
drill dust collector. This is the only way to prevent dust escaping.
Appliance suction function
♦ After you have aligned the laser or put the drill
dust collector/drill against the wall, switch on
the vacuum pump at the switch .
♦ Push the appliance briefly firmly against the
wall. After a short time, the appliance will be
firmly sucked against the wall.
♦ Ensure that the seal
against the wall.
♦ Check that the appliance stays in place by
trying gently to pull it off or slide it across the
surface.
♦ Leave the vacuum pump switched on the whole
time you are working with the line laser and/or
the drill dust collector. Otherwise, the appliance
will not be able to maintain a sufficient vacuum
and the appliance could come off the wall.
♦ Do not use the appliance for overhead work.
♦ If the appliance does not remain on the wall,
it may be because the surface structure of the
wall is simply too rough, and the appliance is
unable to generate a sufficient vacuum. In this
case, you will need a second person to hold the
appliance in place.
♦ Ensure that the seal
by rough surfaces, edges or corners.
of the appliance is fully
is not damaged or cut
Detaching the appliance
♦ First, finish your work with the line laser and/
or the drill and then remove the drill from the
appliance.
♦ Hold the appliance firmly in place to prevent it
from falling down.
♦ Switch off the vacuum pump at the switch
and press the vacuum button .
♦ Remove the appliance from the surface.
♦ Use the protective cover
ance and the seals .
to protect the appli-
Troubleshooting
– The laser is not working
Battery is dead > replace battery.
– Appliance does not grip onto the surface
Battery is dead or too weak > replace battery.
Seal is damaged > Hold the appliance by
hand.
Wall structure is too rough > Hold the appli-
ance by hand.
PLBS 2 A1
GB
│
7 ■
Maintenance and cleaning
WARNING! RISK OF INJURY! Always
switch the appliance off and remove
the battery before carrying out any
work on the appliance.
■ The appliance is maintenance-free.
■ The appliance should only be opened for
repairs by a qualified technician.
■ Heed the safety instructions for batteries.
■ Keep the appliance clean to ensure fault-free
operation.
■ Remove any dirt from the housing with a soft
cloth.
■ Use only water with a little washing-up liquid,
to prevent any possible damage.
■ Do not allow any moisture to penetrate into the
appliance during cleaning.
■ Wear protective gloves when cleaning the
appliance.
■ If, despite careful manufacturing and examina-
tion procedures, the appliance does not function, contact Customer Service.
Storage
If you decide not to use the appliance for a long
period, remove the batteries and store them in a
clean, dry place away from direct sunlight.
Disposal
The packaging is made from environmen-
tally friendly material and can be disposed of at your local recycling plant.
Do not dispose of power tools in
your normal household waste!
European Directive 2012/19/EU requires that
worn-out power tools be collected separately and
recycled in an environmentally compatible manner.
Do not dispose of batteries with the
normal household waste!
Defective or worn-out batteries must be
recycled according to Directive 2006/66/EC.
Take the batteries and/or appliance to a nearby
collection facility for disposal.
Please consult your local authorities regarding suitable disposal of worn-out power tools.
Kompernass Handels GmbH
warranty
Dear Customer,
This appliance has a 3-year warranty valid from
the date of purchase. If this product has any faults,
you, the buyer, have certain statutory rights. Your
statutory rights are not restricted in any way by the
warranty described below.
Warranty conditions
The validity period of the warranty starts from the
date of purchase. Please keep your original receipt
in a safe place. This document will be required as
proof of purchase.
If any material or production fault occurs within
three years of the date of purchase of the product,
we will either repair or replace the product for you
at our discretion. This warranty service is dependent on you presenting the defective appliance and
the proof of purchase (receipt) and a short written
description of the fault and its time of occurrence.
If the defect is covered by the warranty, your product
will either be repaired or replaced by us. The repair
or replacement of a product does not signify the
beginning of a new warranty period.
Warranty period and statutory
claims for defects
The warranty period is not prolonged by repairs
effected under the warranty. This also applies to
replaced and repaired components. Any damage
and defects present at the time of purchase must
be reported immediately after unpacking. Repairs
carried out after expiry of the warranty period shall
be subject to a fee.
■ 8
│
GB
PLBS 2 A1
Scope of the warranty
This appliance has been manufactured in accordance with strict quality guidelines and inspected
meticulously prior to delivery.
The warranty covers material faults or production
faults. The warranty does not extend to product
parts subject to normal wear and tear or fragile
parts such as switches, batteries, baking moulds or
parts made of glass.
The warranty does not apply if the product has
been damaged, improperly used or improperly
maintained. The directions in the operating instructions for the product regarding proper use of
the product are to be strictly followed. Uses and
actions that are discouraged in the operating
instructions or which are warned against must be
avoided.
This product is intended solely for private use and
not for commercial purposes. The warranty shall be
deemed void in cases of misuse or improper handling,
use of force and modifications/repairs which have
not been carried out by one of our authorised
Service centres.
Warranty claim procedure
To ensure quick processing of your case, please
observe the following instructions:
▯ Please have the till receipt and the item number
(e.g. IAN 12345) available as proof of purchase.
▯ You will find the item number on the type plate,
an engraving on the front page of the instructions
(bottom left), or as a sticker on the rear or bottom
of the appliance.
▯ If functional or other defects occur, please
contact the service department listed either by
telephone or by e-mail.
▯ You can return a defective product to us free of
charge to the service address that will be provided
to you. Ensure that you enclose the proof of
purchase (till receipt) and information about
what the defect is and when it occurred.
You can download these instructions
along with many other manuals,
product videos and software on
www.lidl-service.com.
Service
Service Great Britain
Tel.: 0871 5000 720 (£ 0.10/Min.)
E-Mail: kompernass@lidl.co.uk
PLBS 2 A1
IAN 277698
Importer
Please note that the following address is not the
service address. Please use the service address
provided in the operating instructions.
KOMPERNASS HANDELS GMBH
BURGSTRASSE 21
44867 BOCHUM
GERMANY
www.kompernass.com
│
GB
9 ■
■ 10
│
GB
PLBS 2 A1
Obsah
Úvod ..........................................................12
Použití vsouladu surčením .................................................... 12
Vybavení .................................................................12
Rozsah dodávky ............................................................ 12
Technické údaje ............................................................12
Bezpečnostní pokyny .............................................13
Bezpečnost na pracovišti .....................................................13
Elektrická bezpečnost ........................................................13
Bezpečnost osob a pravidla chování, specifická pro laser ...........................13
Použití přístroje a nakládání s ním ..............................................14
Použití baterií a manipulace s nimi .............................................. 14
Bezpečnostní pokyny specifické pro přístroj ....................................... 15
Před uvedením do provozu ........................................16
Vložení/výměna baterií ...................................................... 16
Použití ochranného krytu / nástěnného držáku ....................................16
Příprava přístroje ...........................................................16
Uvedení do provozu ..............................................16
Zapnutí a vypnutí čárového laseru .............................................. 16
Vyrovnání čárového laseru .................................................... 16
Použití lapače prachu při vrtání ................................................17
Vyprázdnění lapače prachu při vrtání ...........................................17
Přisátí přístroje ............................................................. 17
Uvolnění přístroje ...........................................................18
Odstranění závad ................................................18
Údržba a čištění .................................................18
Skladování .....................................................18
Likvidace .......................................................18
Záruka společnosti Kompernass Handels GmbH .......................19
Servis .................................................................... 20
Dovozce .................................................................. 20
PLBS 2 A1
CZ
│
11 ■
Loading...