|
|
|
ORDER NO. |
Front |
Center |
Rear |
RRV2359 |
SPEAKER SYSTEM
S-HS77-FXMA/NC
S-HS77-CR XMA/NC
FOR PRECAUTION OF
REASSEMBLY AND DISASSEMBLY
[ Front speaker ] [ Center speaker ]
The grille is attached to the cabinet by catches.
Detach by pulling it toward you.
The woofer is attached to the baffle by 4 external screws. To detach it, unfasten those screws.
When attaching it, face its terminal downward.
The midrange is attached to the flange lower side by 4 external screws. To detach it, unfasten those screws. When attaching it, face its terminal downward.
The tweeter is attached to the flange upper side by 2 external screws. To detach it, unfasten those screws. When attaching it, first reattach the packing around tweeter diaphragm, then face its terminal downward.
The flange is attached to the baffle by 4 external screws. To detach it, unfasten those screws. When attaching it, face it downward.
To detach the midrange or tweeter, first remove the flange. Then remove it.
The input terminal is attached to the back board by press-fitting and applied with adhesive. To detach it, pry it open by inserting a flat blade screwdriver into lower side.
The Network Assy is attached to the input terminal by soldaring.
The grille is attached to the cabinet by catches.
Detach by pulling it toward you.
The woofer is attached to the baffle by 4 external screws. To detach it, unfasten those screws.
When attaching it, first exchange the flange, then face its terminal downward.
The tweeter is attached to the baffle by 4 external screws.
The cosmetic packing is attached to the flange applied with adhesive.To detach the tweeter. First remove the cosmetic packing, then unfasten those screws. When attach it, do so that it will move vertical. The tweeter wires, connected in the middle of network Assy , are covered with the insulating tape.
The input terminal is attached to the back board by press-fit- ting. To detach it, pry it open by inserting a flat blade screwdriver into lower side.
The Network Assy is attached to the input terminal by soldaring.
[ Rear speaker ]
When exchange the rear speaker, do it with the CS Assy (R).
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS SERVICE, INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2000
T-ZZM JULY 2000 Printed in Japan
S-HS77-F, S-HS77-CR
PARTS LIST
NOTES: 
Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List. 
The 
mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation.
[S-HS77-F]
Mark |
No. |
|
|
Description |
|
Part No. |
NSP |
CS Assy |
|
SMW1608 |
|||
NSP |
|
|
|
Label Back |
|
SAN2869 |
|
|
|
|
|||
|
Packing (for Flange) |
|
SEC1454 |
|||
|
Packing (for Duct) |
|
SEC1455 |
|||
|
Packing (for Tweeter) |
|
SEC1457 |
|||
|
Input Terminal Board |
|
SKX1059 |
|||
|
Grille Assy |
|
SMG1676 |
|||
NSP |
|
|
|
Grille Frame |
|
SNK2444 |
|
|
|
||||
NSP |
Catch |
|
SNK-883 |
|||
|
Flange Assy |
|
SNX1140 |
|||
NSP |
|
|
|
Flange |
|
SNK2445 |
|
|
|
|
|||
|
Duct Flange Assy |
|
SNX1143 |
|||
NSP |
|
|
|
Badge |
|
SAM1443 |
|
|
|
||||
NSP |
|
|
|
Duct Flange |
|
SNK2446 |
|
|
|
|
|||
|
Network Ass'y |
|
SWN1644 |
|||
|
Speaker (Woofer) |
|
Q20EU92-51F |
|||
|
Speaker (Mid-range) |
|
SWS9021 |
|||
|
Speaker (Tweeter) |
|
SWS9022 |
|||
|
Screw (for WF and Flange Assy) |
|
SBA1176 |
|||
|
Screw (for Mid-range) |
|
BPZ30P060FZK |
|||
|
Screw (for Tweeter)) |
|
BPZ30P080FZK |
|||
For Packing
NSP |
Accessories Assy |
SME2997 |
|||
NSP |
|
|
|
Polyethylene Bag |
E11-024 |
|
|
|
|||
|
|
|
|
Speaker Wire (red) |
SDS1074 |
|
|
|
|
||
|
Operating Instructions |
SRD1221 |
|||
|
|
|
|
( English/Spanish/Chinese) |
|
|
Protector (L) |
SHA2204 |
|||
|
Protector (R) |
SHA2205 |
|||
|
Packing Case |
SHG2303 |
|||
|
Packing Bag |
SHL1243 |
|||
[S-HS77-CR]
Mark |
No. |
|
Description |
|
Part No. |
|
NSP |
CS Assy (C) |
|
SMW1609 |
|||
NSP |
|
|
|
Label Back |
|
SAN2870 |
|
|
|
||||
NSP |
CS Assy (R) |
|
SMW1610 |
|||
NSP |
|
|
|
Label Back |
|
SAN2871 |
|
|
|
|
|||
|
Packing |
|
SEC1507 |
|||
|
Felt |
|
|
|
SER1240 |
|
|
Input Terminal Board |
|
SKX1059 |
|||
|
Grille Assy (Center) |
|
SMG1677 |
|||
NSP |
|
|
|
Badge |
|
SAM1443 |
|
|
|
||||
NSP |
|
|
|
Grille Frame |
|
SMH1005 |
|
|
|
|
|||
|
Cosmetic Flange |
|
SNK2447 |
|||
NSP |
Catch |
|
SNK2499 |
|||
|
Speaker (Center) |
|
SWM9016 |
|||
|
Speaker (Tweeter) |
|
FK26AP02-63F |
|||
|
Network Assy (Center) |
|
SWN1657 |
|||
|
Screw (for rear speaker) |
|
BYC35P250FZB |
|||
|
Screw (for center speaker) |
|
SBA1177 |
|||
For Packing
NSP |
Accessories Assy |
SME2998 |
|||
NSP |
|
|
|
Polyethylene Bag |
E11-024 |
|
|
||||
|
|
|
|
Speaker Wire (orange) |
SDS1075 |
|
|
|
|
||
|
|
|
|
Speaker Wire (blue) |
SDS1076 |
|
|
|
|
||
|
|
|
|
Speaker Wire (yellow) |
SDS1077 |
|
|
|
|
||
|
Operating Instructions |
SRD1222 |
|||
|
|
|
|
( English/Spanish/Chinese) |
|
|
|
|
|
|
|
|
Protector |
SHA2206 |
|||
|
Packing Case |
SHG2304 |
|||
NSP |
Packing Bag (Center) |
SHL1242 |
|||
|
Packing Bag (Rear) |
SHL1244 |
|||
2
Loading...