Pioneer MVH-X580BS, MVH-X580BSXNUC, MVH-X580DAB, MVH-X580DABXNEW5, MVH-X580BT Service Manual

...

0 (0)

PIONEER CORPORATION 28-8, Honkomagome 2-chome, Bunkyo-ku, Tokyo 113-0021, Japan

PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 2 Jalan Kilang Barat, #07-01, Singapore 159346

PIONEER CORPORATION 2016

DIGITAL MEDIA RECEIVER

ORDER NO.

CRT5837

MVH-X580BS/XNUC

MVH-X

580BS

MVH-X580DAB/XNEW5 MVH-X580BT/XNEW5 MVH-X585BT/XNES

/XNUC

K-ZZZ MAY 2016 Printed in Japan

1234

SAFETY INFORMATION

CAUTION

Danger of explosion if battery is incorrectly replaced. Replaced only with the same or equivalent type recommended by the manufacturer. Discord used batteries according to the manufacturer's instructions.

CAUTION

Where in a manufacturer’s service documentation, for example in circuit diagrams or lists of components, a symbol is used to indicate that a specific component shall be replaced only by the component specified in that documentation for safety reasons, the following symbol shall be used:

This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so and refer the repair to a qualified service technician.

WARNING

This product may contain a chemical known to the State of California to cause cancer, or birth defects or other reproductive harm. Health & Safety Code Section 25249.6 - Proposition 65

MVH-X580BS/XNUC

5678

SAFETY INFORMATION .....................................................................................................................................2

1. SERVICE PRECAUTIONS ................................................................................................................................4

1.1 SAFETY PRECAUTIONS...........................................................................................................................4

1.2 NOTES ON DISASSEMBLY / ASSEMBLY .................................................................................................4

1.3 NOTES ON OPERATION CHECK / DIAGNOSIS.......................................................................................4

1.4 NOTES ON REPLACING PARTS ...............................................................................................................5

1.5 OTHERS.....................................................................................................................................................5

2. SPECIFICATIONS.............................................................................................................................................6

2.1 SPECIFICATIONS ......................................................................................................................................6

2.2 DISC/CONTENT FORMAT .........................................................................................................................6

3. BASIC ITEMS FOR SERVICE ..........................................................................................................................6

3.1 CHECK POINTS AFTER SERVICING .......................................................................................................6

4. BLOCK DIAGRAM ............................................................................................................................................7

4.1 BLOCK DIAGRAM......................................................................................................................................7

4.2 POWER BLOCK DIAGRAM .......................................................................................................................8

5. DIAGNOSIS ......................................................................................................................................................9

5.1 OPERATIONAL FLOWCHART ...................................................................................................................9

5.2 ERROR CODE LIST.................................................................................................................................10

5.3 CONNECTOR FUNCTION DESCRIPTION .............................................................................................12

5.4 FUSE (POLY SWITCH) CHECK...............................................................................................................14

6. SERVICE MODE.............................................................................................................................................15

6.1 DISPLAY TEST MODE 1..........................................................................................................................15

6.2 DISPLAY TEST MODE 2..........................................................................................................................16

6.3 SOFTWARE VERSION UP METHOD......................................................................................................17

7. DISASSEMBLY ...............................................................................................................................................18

8. EACH SETTING AND ADJUSTMENT............................................................................................................20

9. EXPLODED VIEWS AND PARTS LIST ..........................................................................................................21

1 PACKING ..................................................................................................................................................21

9.2 EXTERIOR ...............................................................................................................................................23

10. SCHEMATIC DIAGRAM................................................................................................................................26

10.1 TUNER AMP UNIT (VEHICLE I/F) .........................................................................................................26

10.2 TUNER AMP UNIT (SYSTEM REGULATOR ) .......................................................................................27

10.3 TUNER AMP UNIT (DDCON).................................................................................................................28

10.4 TUNER AMP UNIT (OTHER SUPPLY)...................................................................................................29

10.5 TUNER AMP UNIT (SYSCOM) ..............................................................................................................30

10.6 TUNER AMP UNIT (I/F iPod FLASH MEM)............................................................................................31

10.7 TUNER AMP UNIT (E-VOL(OPAL))........................................................................................................32

10.8 TUNER AMP UNIT (TUNER(LITHIO)) ...................................................................................................33

10.9 TUNER AMP UNIT (HD/DAB MODULE)................................................................................................34

10.10 TUNER AMP UNIT (BT) .......................................................................................................................35

10.11 TUNER AMP UNIT (S11.6 I/F) .............................................................................................................36

10.12 TUNER AMP UNIT (EXTERNAL I/F)....................................................................................................37

10.13 TUNER AMP UNIT (POWER AMP) .....................................................................................................38

10.14 KEYBOARD UNIT ................................................................................................................................39

11. PCB CONNECTION DIAGRAM....................................................................................................................40

11.1 TUNER AMP UNIT .................................................................................................................................40

11.2 KEYBOARD UNIT ..................................................................................................................................42

12. ELECTRICAL PARTS LIST ........................................................................................................................... 43

MVH-X580BS/XNUC

1234

1. SERVICE PRECAUTIONS

 You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and

should keep the safety during servicing by following the safety instructions described in this manual.

 area and a heat sink becomes hot areas. Be careful not to burn yourself.

TUNER AMP UNIT (Side B)

IC201

HEAT SINK

 Before disassembling the unit, be sure to turn off the power. Unplugging and plugging the connectors during power-on

mode may damage the ICs inside the unit.

 Please be sure to conduct line process to original status if you make assembling after repair.

 Resetting the microprocessor

1.Remove the front panel.

2.Press the RESET button with a pointed instrument longer than 8 mm.

RESET button

1.1 SAFETY PRECAUTIONS

1.2 NOTES ON DISASSEMBLY / ASSEMBLY

1.3 NOTES ON OPERATION CHECK / DIAGNOSIS

MVH-X580BS/XNUC

5678

 Be careful in handling ICs. Some ICs such as MOS type are so fragile that they can be damaged by electrostatic

induction.

 Please be careful of not to apply static charge onto integrated circuits, etc, when you conduct repair work. Especially, please use soldering iron with its tip grounded. Also, please use a pair of tweezers with static charge protection capability if there is the possibility of contacting to

device terminals, and avoid the use of metal-made tweezers.

 The part listed below is difficult to replace as a discrete component part. When the part listed in the table is defective, replace whole Assy.

 Notes about installation and pin number description of Power IC (IC1301: PA2032A) The Power IC, PA2032A used on the Tuner Amp Unit is a 25 pin IC. The same PCB of the Tuner Amp Unit is used for other models that use a 27 pin IC, too. So, the PCB has lands for a 27 pin IC. When you replace the Power IC, install the Power IC onto 25 pins (2- 26 pin) located in the center of 27 pins for IC301.

Therefore, when you check the Power IC on the schematic diagram and the PCB connection diagram, you have to pay attention as follows.

BGA BGA Heat pad Heat pad

IC501 U1001 IC201 IC751

STA1080 CWX4751 BD49101AEFS PM9015A

SYSTEM MICROCOMPUTER BT MODULE SYSTEM POWER SUPPLY E-VOL

SCHEMATIC DIAGRAM

The pin number of left side is a number on the PCB (silk printing).

The pin number of right side (in the IC frame) means the pin number of IC itself.

No conn ection

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

No conn ection

IC1301

For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit.

Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs accompanied by reworking of soldering.

Notes on soldering

1.4 NOTES ON REPLACING PARTS

1.5 OTHERS

MVH-X580BS/XNUC

1234

2. SPECIFICATIONS

For all items except the backup current, refer to the Owner's Manual.

Backup current......................... 5.0 mA or less

demrifnocebotmetIserudecorP.oN

1 Confirm whether the customer complain has

been solved. If the customer complain occurs with the specific media, use it for the operation check.

The customer complain must not be reappeared. Display, audio and operations must be normal.

2 FM/AM tuner Check FM/AM tuner action.

(Seek, Preset) Switch band to check both FM and AM.

Display, audio and operations must be normal.

receiving it for service.

Item to be checked regarding audio

Appearance check

No scratches or dirt on its appearance after

2.1 SPECIFICATIONS

2.2 DISC/CONTENT FORMAT

3. BASIC ITEMS FOR SERVICE

3.1 CHECK POINTS AFTER SERVICING

To keep the product quality after servicing, please confirm following check points.

See the table below for the items to be checked regarding audio:

Distortion Noise

Volume too low Volume too hi Volume fluctuatin Sound interrupted

MVH-X580BS/XNUC

5678

4. BLOCK DIAGRAM

Lithio

TEF6686HN-V102

E.VOL

OPAL

IC751

PM9015A

TUN3.3V

SYS+B5.7V

OPAL_3.3V

MUTE

SYS+B5.7V

MUTE

WIRED REMOTE PREOUT

MIC

BT MIC

FM/AM ANT

TUNL TUNR

RL RR

FL FR

STBY

H-SW

B.REM

Power IC

B.Up

JA201 CN1291

Power Connector

B.Up

ACC

1. FL+

2. FR+

3. FL-

4. FR-

5. RL+

6. RR+

7. RL-

8. RR-

9. NC

11. ILM

13. ACC

14. BREM

15. B.UP

16. GND

17. GND

18. B.UP

KEYAD1,KEYAD2

U951

DAB

Module

BTMICIN

ILM

SXI

DIPLAYOUT

SXIL SXIR

AUXL AUXR

DABSXI14V

SXIPW

SXITOSYS

SYSTOSXI

DABSXI14V

D0,D1,CLK,WS

DVCC3.3V

DVCC1.2V

RFVCC3.3V

JA1276

JA1241

JA1231JA851

ILMPW

DIMMER

VDDEN

DD1VON

IC851

EVOL_MCK,EVOL_DATA

EVOL_BCK,EVOL_LRCK

SYSTEM u-com

IC501

STA1080

361pin BGA

ACC

iPod CP

IC701

337S3959

CP_SCL,CP_SDA

CPPW,CPRST

CP_SW3.3V

EEPROM 64KB

(SYS DATA Memory)

IC731

M95512-RMN6P

TUNSCL,TUNSDA

EVOLtoSYS,SYSto,EVOL

EVOL_CS,EVOLCK

USB2_DP,USB2_DM

VDDIO3.3V

RESET

VDD1.2V

ECO

X851 36.48MHz

X502 24.0MHz

SYNC

VDD_SW 3.3V

VDDEN

VDDIO3.3V

A.SENS

VDD 3.3V

DDC2

STBREG

SWVDD 5V

REG5

VDD1.2

REG1

VDD1.2V

SWVDD5V

SYS5.78V

REG2

SYS+B5.7V

B.Up

TUN3.3V

367.347/439.024kHz

VD 6.0V

DDC1

VD6.0V

VDD3.3V

B.Up

BD49101AEFS

B.Up

I.SENS

BSENS

RESET IC

IC502

S-80827CNMC-B8M

PW_SCL,PW_SDA

QSPFDBSCK,

QSPCLK,QIO0,

QIO1,QIO2,QIO3,

QSSL

S-Quad Flash 4MB

(

ILM

TELIN

ROMSCK, ROMCSB

ROMSI,ROMSO

SXIPW

(Stand-by)

DTUNtoSYS,SYStoDTUN

DVCC3 3V

ADI,ADO,

ACLK,AWS

TUNRST

VDDIO_ON3.3V

DAB/SXI_PW

Q401

2SAR502UB

Q201,Q202

SSM3J332R

ANTPW

CP_SW 3.3V

Q701

LSAR523UB

CPPWR

CP_SW3.3V

VDD3.3V

SWVDD5V

DABSXI14V

RFVCC3.3V

IC421

S-1155B33

DD3VON

RFVCC3.3V

DDC5V

IC301

KBD9876EFJ

VDDEN

DDC5V

VDDIO3.3V

HIOUT8V

IC461

NJW4184DL3

HIOUT_EN

HIOUT8V

IC201

DD3VON

CPPWR

BT18EN

BTPW

ECO

SYNC USBCTL1 USBCTL2

MUTE

KYDT

DPDT

ROT0,ROT1

USB1_DP,USB1_DM

X501 32.768KHz

TUN3.3V

REG3

USB1_5V

ILM+B

Hiside SW

USB5V

REG4

BSENS

ILMPW

B.Up

SSENS

AUXL AUXR

BTTOSYS,SYSTOBT,

BTCTS,BTRTS

BTDATAIN,BTDATAOUT

BT_LRCK,BT_BCK

X100

BT MODULE

U1001

CWX4751

BT 3.3V

BT MODULE

BT 3.3V

Q441

2SAR502UB

BT1.8V

IC442

MM3479A18P

BT18EN

BT 3.3V

BT 1.8V

(SYS u-com software)

IC742

MX25L1636EM2I-08G

SDRAM 16MB or 8MB

IC702

M12L128168A-5TG2N

VDDIO3.3V

SWVDD5V

ILM+B

USB1_5V

BT 3.3V

BT_WAKE

DSENS

QSSL2

IC422

MM3411A33N

DVCC1.2V

IC423

S-1172B12-E6

DD3VON

DVCC3.3V

DVCC1.2V

USBCTL

/USBCTL2

USB Hiside SW

IC321

BD2232G-G

BT18EN

USB1_5V

USB HisideSW

IC202

BD2232G-G

SWVDD5V

DD1VON

CLK32KOUT

VDDIO3.3V

VDDIO_ON3.3V

USB2_5V

VDDIO3.3V

LCD

LCD Driver IC1801,IC1802 BU97540KV-M

key matrix

SWVDD5V

SOURCE

USB1_5V

X1801 4.97MHz

Digital Line

CommunicationLine

UART Communicationline

I2S communicationline

Audio Line

Controlline

I2C Communicationline

VBUS

D-

D+

GND

CN1941

1. DGND

2. ILMGND

3. SWVDD

4. ROT1

5. ILM+B

6. ROT0

7. USBGND

8. SDI

9. USBGND

10. SDO

11. USB5V

12. SCK

13. DM

14. SCE

15. DP

16. AUXGND

17. AUXR

18. SOURCE

19. AUXL

20. DSENS

ROTARY

AUX

CN1201

CN1941

ILM+B

RESET

USB1

D-

D+

JA1921 JA1901

BUS

GND

USB2

D-

D+

HIOUT

IC801

NJW1240V

HIOUT8V

VDDEN

USB_CTL1

Q481

EVOL3.3V_SW

LSAR523UB

OPAL_3.3V

HIOUT_EN

IC1301

PA2032A

ABC

PAL013B

DAB ANT

S-Quad Flash 2MB/32MB

(DATA Memory)

IC741 QWW4081 QWW4082 QWW4078

4. BLOCK DIAGRM

KEYBOARD UNIT

TUNER AMP UNIT

A MVH-X580BS/XNUC B MVH-X580DAB/XNEW5 C MVH-X580BT/XNEW5 D MVH-X585BT/XNES

A B

USB2_5V

ABC

4.1 BLOCK DIAGRAM

MVH-X580BS/XNUC

1234

4.2 POWER BLOCK DIAGRAM

B.UP

IC201

L101

BUP14.4V

BD49101AEFS

VDD 3.3V

DDC2

3.15 3.30 3.45

Voltage

1047.6 mA

Current

(

min 1000 mA)

VDD 3.3V STBREG

(

min 200 mA)

DDC1 : CD DDC2 : VDD3.3V LDO1 : VDD1.2V LDO2 : SYS5.8V LDO3 : TUN3.3V LDO4 : USB_H/S_SW LDO5 : SWVDD5V

VDD 1.2V

REG1

Voltage

1.20 1.25 1.30

Current

330.0 mA

(

min 500 mA)

SYS+B

REG2

5.78

Voltage

95.0 mA

Current

(

min 100mA)

SWVDD

REG5

5.00 5.25 5.50

Voltage Current

(min 50 mA)

22.0 mA

VDD3.3V

USB HisideSW

BD2232G-G

2.97 3.30 3.63

252.6 mA

121.25 mW

SSM3J332R

2.97 3.30 3.63

795.0 mA

381.60 mW

VDDIO3.3V

VDD1.2V

SYS+B5.7V

SWVDD5V

IC202

Q202

VDDIO_ON3.3V

EVOL3.3V_SW

VDDEN

CPPWER_SW

Q441

BT 3.3V

2SAR502UB

BT 1.8V

MN3411A33

Q481

2SAR502UB

Q701

LSAR523UB

System u-com(Non SWD) Accordo2

Mecha VDD

BT_ON

BT 3.3V

BT_ON

BT 1.8V

HIOUTEN

E-Volume(Digital)

OPAL_3.3V

CPPWR

i-Pod

CP_SW3.3V

Mecha VDD

System u-con(SWD) Accordo2

RESET IC

S-FLASH(Quad

S-FLASH(Single 2MB)

EEP-ROM(64KB)

SDRAM(16MB)

5 --> 3 IC

System u-com(SWD) Accordo2

E-Volume (Analog)

Power Amp (Mute)

Power Amp (STBY)

Grill u-com

3 --> 5 IC

MAX TYP PART NO.

0.1 mA

97.5 mA 65.0 mA

60.0 mA 57.0 mA

67.0 mA PM9015A95.0 mA

7.5 mA

150.0 mA

0.0 mA 0.0 mA S-80827CNMC-B8M

4MB)

17.0 mA

35.0 mA

80.0 mA

717.6 mA

6.0 mA

10.0 mA MX25L1636EM2I-08G

330.0 mA

1047.6 mA

95.0 mA 72.0 mA PM9015A

0.018 mA

10.0 mA

3.0 mA

STA1080 S11.6 STD

BT HIC

337S3959

S11.6 STD171 mA

STA1080

MX25L1636EM2I-08G

M95512-RMN6P2.5 mA

M12L128168A-5TG2N

TC7SH126FU2.0 mA

STA1080

BU97540KV

TC7SET08FUS12.0 mA

ILM+B SW Hiside-SW

(

min 500 mA)

Current

220.0 mA

Mecha VD 6.0V

DDC1

Voltage

6.00 V

Current

2 715 mA

REG4

REG3

3.14 3.30 3.47

215.0 mA

6.00 8.00 9.00

20.0 mA

5.00 5.25 5.50 2 450.0 mA

Q401

REG4EN

HIOUTEN

VDDEN

ANTPW

DDC5V

USB LDO

(min 1500 mA)

BUP14.4V

BUP14.4V BUP14.4V

Voltage Current

(min 300 mA)

NJW4184DL3 Voltage Current

Voltage Current

DAB ANT PW

TUN 3.3V

IC461

HIOUT8V

IC301

DDC 5V

KBD9876EFJ

SXI PW

ILMPW

VD6.0V

USB1_5V

TUN3.3V

HIOUT8V

DABSXI14V

DVCC3.3V

MM3411A33N

S-1172B12-E6

RFVCC3.3V

S-1172B12-E6

USB HisideSW

BD2232G

IC422

IC423

HD1.2V

IC421

IC321

RGB model

DTUN3V_ON

DTUN1V_ON

USBCTL1

K/B Illumi (RGB)

Mecha VD

USB1/USB2

Si-Tuner

HIOUT

DVCC3.3V

DVCC1.2

RFVCC3.3V

USB1

DAB ANT SXI PWR

Power Amp

220 mA

1 000.0 mA 300.0 mA

1 500.0 mA 1 000.0 mA

215.0 mA 150.0 mA

2715.0 mA

S11.6 STD

USB1

Lithio

1450.0 mA

20.0 mA 12.0 mA NJW1240V

126 mA 50 mA

383 mA 225 mA

441 mA

1 500 mA 1 000 mA

414 mA

USB1

2 450 mA

400 mA

300 mA 185 mA

A MVH-X580BS/XNUC B MVH-X580DAB/XNEW5 C MVH-X580BT/XNEW5 D MVH-X585BT/XNES

MVH-X580BS/XNUC

5678

VDDIO_On : Pin E13

Signal on System ucom(IC501)

bsens : Pin A18 or IC201 Pin40

asens : Pin A15

dsens : Pin A17

VDDEN : Pin B15

VDDIO3.3V : Pin E6,E7,E8,F7,F8,M6-M14 VDD1.2V : Pin E9,E10,F6,F9,G5,N5,N6,N10-N13

SWVDD : IC201 Pin1

SYS+B5.7V : IC201 Pin16

VDDIO_On = 3.3V

bsens

asens

dsens

VDD1.2V = 1.2V

VDDIO3.3V = 3.3V

bsens = L

asens = L

Starts

communication

SOC

dsens = L

SWVDD = 5.2V

Source ON

SYS+B5.7V = 5.7V

Completes power-on operation.

(After that, proceed to each source operation)

Power ON

VDDENH

VDDEN = H

Starts

communication

LCD driver

5. DIAGNOSIS

5.1 OPERATIONAL FLOWCHART

MVH-X580BS/XNUC

1234

5.2 ERROR CODE LIST

Common

AMP ERROR

This unit fails to operate or the speaker connection is incorrect.

– Check the speaker connection. – Check the power IC and its peripheral circuit.

NO XXXX (NO TITLE, for example)

There is no embedded text information. – Switch the display or play another

track/file.

DAB tuner

ANTENNA ERROR

The antenna connection is incorrect. – Check the antenna connection. – Turn the ignition switch OFF and back

to ON again. If the message remains, contact your dealer or an authorized

Pioneer Service Station for assistance.

Bluetooth device

ERROR-10

The power failed for the Bluetooth module of the unit. – Turn the ignition switch OFF and back

to ACC or ON.

Apps

NO BT DEVICE GO TO BT MENU TO REGISTER

No Bluetooth device found. – Connect the unit and the device via

Bluetooth.

CONN. FAILED PRESS BAND KEY TO RETRY

Bluetooth connection failed.

DISCONNECTED PRESS BAND KEY TO RETRY

Bluetooth connection failed.

CHECK APP

Connection to the application failed. – Follow the instructions that appear on

the screen.

– Press BAND / to make a

connection again.

– Press BAND / to make a

connection again.

START UP APP

The application has not started running yet. –Operate the mobile device to start up

the application.

Spotify

NO BT DEVICE GO TO BT MENU TO REGISTER

No Bluetooth device found. – Connect the unit and the device via

Bluetooth.

CONN. FAILED PRESS BAND KEY TO RETRY

Bluetooth connection failed.

CHECK APP PRESS BAND KEY TO RETRY

Connection to the Spotify application failed.

DISCONNECTED PRESS BAND KEY TO RETRY

Bluetooth connection lost.

CHECK APP

Connection to the Spotify application failed. – Follow the instructions that appear on

the screen.

–Press BAND/ to make a

connection again.

–Press BAND/ to make a

connection again.

–Press BAND/ to make a

connection again.

Pandora

ERROR-19

Communication failed. – Disconnect the cable from the device.

Once the device’s main menu is displayed, reconnect the device and reset it.

START UP APP

The Pandora application has not started running yet. – Start up the Pandora application.

RATING ERROR

The thumb rating operation was disabled. – Run the same command for another

track.

CAN'T SKIP

The skip operation was disabled. – Run the same command for another

track.

TRY LATER

Unable to save thumb rating. Unable to save BookMark. Unable to add station. – Try again later.

MAINTENANCE

Pandora system is undergoing maintenance. – Try again later.

SKIP LIMIT

Due to music licensing restrictions, Pandora limits the total number of skips per hour. – Wait until Pandora allows you to skip

again.

UPDATE APP

This version of the Pandora application is not supported. – Connect a device that has a

compatible version of the Pandora application installed.

Your Pandora account is not logged in. – Disconnect the cable from the device,

and log in to your Pandora account. Then reconnect the device.

CHECK DEVICE

Device error message displayed in the Pandora application. – Check the connected device.

PLEASE CREATE A STATION ON THE PHONE

No station found. – Create a station in the Pandora

application on your connected device.

SELECT STN

No station selected. – Select a station.

NO BT DEVICE GO TO BT MENU TO REGISTER

No Bluetooth device found. – Connect the unit and the device via

Bluetooth.

CONN. FAILED PRESS BAND KEY TO RETRY

Bluetooth connection failed.

connection again.

CHECK APP PRESS BAND KEY TO RETR

Connection to the Pandora application failed.

connection again.

–Press BAND / to make a

DISCONNECTED PRESS BAND KEY TO RETRY

Bluetooth connection lost.

connection again.

STATION FULL

A new station cannot be added. – Delete an old station to open a spot

for a new one.

CAN.T DELETE

The station could not be deleted. – Run the same command for another

station.

NO NETWORK

The connected device is out of area. –Connect the device to a network.

NO SERVICE IN THIS COUNTRY

The connected device is out of area. –Connect the device to a network.

STN DELETED

The operation was disabled. – Run the same command for another

station.

MVH-X580BS/XNUC

5678

SiriusXM Satellite Radio

CHECK ANTENNA

The antenna cable may be either disconnected or damaged. – Check the antenna connection or

replace if damaged.

CHECK TUNER

The radio is having difficulty communicating with the SiriusXM Connect Vehicle Tuner. The tuner may be disconnected or damaged. – Verify that the SiriusXM Connect

Vehicle Tuner cable is securely connected to the radio.

NO SIGNAL

The SiriusXM Connect Vehicle Tuner is having difficulty receiving the SiriusXM satellite signal. – Move your vehicle outdoors with a

clear view of the southern sky.

– Make sure that the SiriusXM magnetic

mount antenna is mounted on a metal surface on the outside the vehicle.

– Move the SiriusXM antenna away from

any obstructions.

SUBSCRIPTION UPDATED

This unit has detected a change in your SiriusXM subscription status. – Press any key to clear the message.

CH UNAVAIL

The channel that you have requested is not available. – Check the SiriusXM channel lineup.

CHAN UNSUB

The channel that you have requested is not included in your SiriusXM subscription package. – Check the content of your SiriusXM

subscription package.

CH LOCKED

The channel has been locked by the Parental Control function. – Set [LOCKED CH] to [OFF] or [CLEAR

ALL] to [YES] in the FUNCTION settings.

NO TUNEMIX CH

There is only one music in the band. – Select a band with two or more

channels.

– Add more music channels to the

current band.

MVH-X580BS/XNUC

1234

5.3 CONNECTOR FUNCTION DESCRIPTION

1 SXiL 2 SXiTX 3 NC 4 SXiR 5 SXiG 6 SXiRX 7 NC 8 GND 9 SXi PW 10 SXiPW

Sirius XM BUS

FM/AM ANTENNA INPUT

Sirius XM BUS (MVH-X580BS/XNUC)

WIRED

REMOTE

CONTROL

MICROPHONE

INPUT

SUBWOOFER OUTPUT

FRONT

OUTPUT

REAR

OUTPUT

10 8

1 FL+ 2 FR+ 3 FL4 FR5 RL+ 6 RR+ 7 RL8 RR-

9 NC 10 NC 11 ILL 12 NC 13 ACC 14 B.REM 15 B.UP 16 GND

MVH-X580BS/XNUC MVH-X580DAB/XNEW5 MVH-X580BT/XNEW5

DAB ANTENNA INPUT (MVH-X580DAB/XNEW5)

MVH-X580BS/XNUC

5678

FM/AM ANTENNA

INPUT

WIRED

REMOTE

CONTROL

MICROPHONE

INPUT

SUBWOOFER OUTPUT

FRONT

OUTPUT

REAR

OUTPUT

10 8

123

214

1 FL+ 2 FR+ 3 FL4 FR5 RL+ 6 RR+ 7 RL8 RR-

1 VBUS 2 D− 3 D+ 4 GND

9 NC 10 NC 11 ILL 12 NC 13 ACC 14 B.REM 15 B.UP 16 GND

MVH-X585BT/XNES

USB PORT

MVH-X580BS/XNUC

1234

5.4 FUSE (POLY SWITCH) CHECK

*Q1243

1234

*Q1242

1234

*Q1241

123 4

*R1246

C1248

100p/50

R1247

22k

R1248

22k

C1247

100p/50

C1250

100p/50

R1249

22k

R1250

22k

C1249

100p/50

R1252

22k

C1251

100p/50

C1252

100p/50

R1251

22k

GND

*R1243

*R1244

*R1241

*R1242

C1254

0.1u/10

C1253

0.01u/16

*R1245

P1243

FSMD075

JA1241

CKB1113

R1256

R1254

R1255

R1253

L1292

VTL1126-A

L1293

VTL1126-A

L1294

VTL1126-A

L1296

VTL1126-A

L1297

VTL1126-A

L1295

VTL1126-A

R1284

1608

L1298

GND

3P/O

SWR

GND

SWL

2P/O

3P/O

PREOUT

- No sounds and display output of external unit (the condition when the fuse is blown (poly switch is working))

This product may receive excessive current if the power line connection of the external product is incorrect, such as Ground connection failure. The poly switch P1243 on TUNER AMP UNIT is used to protect this product from this excessive current. Even though poly switch is working to cut the circuit, the sounds of Pre-out output and AUX input are output properly and also other functions work correctly. However, you cannot turn on the external product connected to this product as the power is not supplied if the poly switch is working to cut the circuit. (The symptom in this case is the sounds of external product are not output on this product when the external product is connected on a vehicle.)

If you find the symptoms above, check whether or not the poly switch is working to cut the circuit. If there is any problem (you cannot turn on the power of external unit), check the power connection (Ground) of external unit.

MVH-X580BS/XNUC

5678

ROTARY 3

LISTSOURCE

PHONE

Grille condition

Confirmation item Operate LCD ILM

All light up PHONE + LIST States 1 Red All light off SOURCE States 2 (No light) No light

Button feeling

(and ILM light)

Button 3 States 3 Blue

LCD States

Status 1: All light up. Refer to "Draw 1" below for detail. States 2: All light off Status 3: Refer to "Draw 2" below for deference among the models.

Draw 1

Draw 2

Press and hold "PHONE" and "LIST" buttons together, and turn BUP and ACC on.

[How to enter Test mode]

6. SERVICE MODE

6.1 DISPLAY TEST MODE 1

MVH-X580BS/XNUC

1234

6.2 DISPLAY TEST MODE 2

* Initial condition

$ PD number

For Ver.7.01, "701" is displayed

For PEA010A, "010A" is displayed

# System microcomputer version

$$$$

###

1 + 3

On (state when entering test mode)

Press and hold "1" and "3" buttons together, and turn BUP and ACC on.

[Operation key]

[How to enter Test mode]

[Test items]

Start display test mode. Press and hold "1" and "3" buttons together, and turn BUP and ACC on.

Display is normally updated

Display update is stopped

Product operation is performed as usual, in appearance.

The screen gets still when entering this item.

On (an initial value)

On (lighting condition of normal times)

On (an initial value or setting value of default menu)

Off

All off

Remarks

Key Illumination

Operation key Processing

Icon

Enter display test mode Switch to next test mode

The information such as the system microcomputer version is checked.

Switching to next display by pressing “ 1 ” + “ 3 ” buttons together.

System Version information is displayed.

MVH-X580BS/XNUC

+ 35 hidden pages

Pioneer MVH-X580BS, MVH-X580BSXNUC, MVH-X580DAB, MVH-X580DABXNEW5, MVH-X580BT Service Manual

SAFETY INFORMATION

CONTENTS

1. SERVICE PRECAUTIONS

1.1 SAFETY PRECAUTIONS

1.2 NOTES ON DISASSEMBLY / ASSEMBLY

1.3 NOTES ON OPERATION CHECK / DIAGNOSIS

1.4 NOTES ON REPLACING PARTS

1.5 OTHERS

2. SPECIFICATIONS

2.1 SPECIFICATIONS

2.2 DISC/CONTENT FORMAT

3. BASIC ITEMS FOR SERVICE

3.1 CHECK POINTS AFTER SERVICING

4. BLOCK DIAGRAM

4.1 BLOCK DIAGRAM

4.2 POWER BLOCK DIAGRAM

5. DIAGNOSIS

5.1 OPERATIONAL FLOWCHART

5.2 ERROR CODE LIST

5.3 CONNECTOR FUNCTION DESCRIPTION

5.4 FUSE (POLY SWITCH) CHECK

6. SERVICE MODE

6.1 DISPLAY TEST MODE 1

6.2 DISPLAY TEST MODE 2