PRODUCT SPECIFICATION |
analog systems and controls |
|
|
CM9770 Series Matrix
MICROPROCESSOR-BASED SWITCHER/CONTROLLER; 2,048 INPUTS; 512 OUTPUTS
Product Features
•Microprocessor-Based, Full Cross-Point Video Matrix
•High-Density Architecture Supports up to 256 Cameras and 32 Monitors in Each Bay
•Control up to 2,048 Cameras and 512 Monitors in a Single Node or Expand Camera Capacity with a Multi-Node System (up to 24 Nodes)
•Full System Reports From CM9700-MGR Provide System Wiring and Configuration Details
•Sixteen RS-422 COM Ports (Expandable to 120) and Two RS-232 Full-Duplex Ports Available on the CPU
•System Diagnostic LEDs Displayed on Front Panel
•Flash Technology Eases System Maintenance and Upgrades
•Logical Camera Selection and Priority Level Operation
•Multiplexer and DVR Control Via Keyboard
•Built-in Video Loss Detection
•Windows®-Based System Management Software (Windows 2000, XP) Includes Multilanguage Menus and On-Screen Help
•Factory Tested Prepackaged Systems
•ASCII Data Input to Interface Access Control and Other External Computer-Based Systems
•Powerful Macro Programming
Optional Accessories
•“Hot Switch” and Backup CPU Ensure Uninterrupted Operation
•Redundant Power Supplies for Switching Bays
•Coaxitron® Translator Allows PTZ Communication Over Standard Coaxial Cable
•Responds to 5,000 Alarms
•Network Interface Unit Allows Multiple Systems to Share Video and Control
•DVR Management
All CM9770 Series systems require installation by a Pelco Certified Dealer/ Installer. This specification sheet may be used for purpose of information only and does not constitute approval or certification of receiving party. Proof of certification must be provided prior to shipment of CM9770 Systems contained herein.
The 9770 System is a full-featured video matrix switching control system that allows users to view and control up to 2,048 cameras and 512 monitors on a single node. Expanded monitor capacity in the matrix bay allows implementation of larger systems with a smaller footprint (less hardware) than other matrix systems.
The base configuration for the 9770 System is made up of a central processing unit (CC1), matrix switching bay(s) (MXBs) with video input/output modules, and keyboard controllers (KBDs). Optional components can be added to enhance system capabilities.
Preconfigured, prepackaged systems make installation fast and simple. The 9770 System features a user-friendly Windows-based management system, which allows for easy system programming and maintenance.
Macros allow activation of events based on schedule or alarm. Macros may call system-wide sequences (tours); activate preset positions on properly equipped cameras; and activate external relays to control auxiliary functions such as locking doors (additional equipment may be required).
The 9770 System also includes built-in video loss detection and system diagnostic features, indicated by LEDs on the front panel of the matrix bay. Flash technology incorporated into the system design allows for easier system maintenance and upgrades.
Optional DVR management allows DVRs to be controlled directly from the system keyboards. Suitable DVRs can be monitored for operational conditions ensuring continuous recording.
International Standards
Organization Registered Firm;
ISO 9001 Quality System
C1555 / REVISED 11-2-10
SYSTEM COMPONENTS/TECHNICAL SPECIFICATIONS
CENTRAL PROCESSING UNIT (CC1)
The central processing unit communicates with external devices and accepts commands from external computers, keyboards, graphical user interfaces (GUIs), access control systems, casino data systems, programmable logic controllers (PLCs), and lighting and intercom systems. An internal VGA card is included for displaying system diagnostics and for programming. RS-422 COM ports are provided for communication with external devices such as matrix switching bays, pan/tilt or dome receivers, and keyboards.
ELECTRICAL |
|
Input Voltage |
120 VAC, 60 Hz or 230 VAC, 50 Hz, autoranging |
Power Consumption |
57 W |
MATRIX SWITCHING BAY
Each bay includes a power supply and mounting baffle and will support modules for up to 256 camera inputs and 32 monitor outputs. Multiple bays can be used to expand a single CPU system to a maximum of 2,048 camera inputs and 512 monitor outputs. An optional backup power supply module (MPS) can be installed in each bay to provide redundancy.
ELECTRICAL |
|
Input Voltage |
100-240 VAC, 50/60 Hz, autoranging |
Power Consumption |
60 W maximum (fully populated) |
Communication |
Full duplex RS-422 using an RJ-45 connector |
VIDEO |
|
Bandwidth |
15 MHz |
Signal-to-Noise Ratio |
-70.5 dB |
Adjacent Channel Crosstalk |
-60.9 dB at 3.58 MHz |
Differential Gain |
0.51% |
Differential Phase |
0.38 degrees |
Line Tilt |
0.40% |
Field Tilt |
0.59% |
Switching Time |
16 mS |
Inputs |
Card slots support up to 256 inputs per bay |
Outputs |
Two output card slots for supporting 32 outputs |
|
per bay |
Video Input Level |
0.5 to 2 Vp-p, RS-170 composite video |
Impedance |
75 ohms terminating (looping versions |
|
available) |
Diagnostic Monitor Output |
One VGA |
I/O Ports |
Sixteen RS-422 ports (expandable to 32); total |
|
system capability is 120 ports* |
|
Two RS-232 ports |
|
One parallel printer port |
|
One VGA output port |
|
Two PC-AT compatible keyboard ports |
GENERAL |
|
Operating Temperature |
32° to 120°F (0° to 49°C) |
Dimensions |
19.50" D x 19.00" W x 7.00" H |
|
(49.53 x 48.26 x 17.78 cm) |
Mounting |
Fits 19-inch EIA-standard rack (4 RUs) |
Unit Weight |
29.7 lb (13.5 kg) |
Shipping Weight |
43 lb (19.5 kg) |
CERTIFICATIONS
•CE, Class A
•FCC, Class A
•UL/cUL Listed
•C-Tick
V-Sync |
The Pelco V-Sync signal (sent up the coax |
|
cable) provides a synchronization pulse which |
|
allows roll-free switching between cameras |
|
within the same matrix bay |
Vertical Drive |
Input connector available on rear panel |
Overall Frequency Response |
Flat to 8 MHz |
Luminance Nonlinearity |
20% |
GENERAL |
|
Operating Temperature |
32° to 122°F (0° to 50°C), non-condensing |
Dimensions |
|
Matrix Bay |
21.70" D x 19.00" W x 10.50" H |
|
(55.10 x 48.26 x 26.67 cm) |
Mounting Baffle** |
24.00" D x 19.00" W x 1.75" H |
|
(60.96 x 48.26 x 4.45 cm) |
Mounting |
Fits 19-inch EIA-standard rack (matrix bay: |
|
6 RUs; mounting baffle: 1RU) |
Unit Weight |
33 lb (14.99 kg) |
|
52 lb (23.59 kg), fully populated |
Shipping Weight |
44 lb (19.96 kg) |
|
62 lb (28.12 kg), fully populated |
CERTIFICATIONS
•CE, Class A
•FCC, Class A
•UL/cUL Listed
•C-Tick
*The CM9700-CC1 is equipped with 16 RS-422 COM ports; total capacity can be expanded to 32 ports by adding two CM9700-SER serial communication cards (8 ports each). Total system capability can be expanded to 120 RS-422 COM ports by adding three CM9700-SER-32 port expansion units (32 ports each) to the CC1.
**Included with each MXB unit. Total height of MXB with baffle installed is 12.25 inches (31 cm).