Installation and Assembly:
Straight Column Mount for 32" - 71" Flat Panel Displays
Model Max. Load Screen Size Range
PLCM-1CP 225 lb. (102.3 kg.) 32'' - 71''
PLCM-UNL-CP 200 lb. (90.7 kg.) 32'' - 65''
Max UL Load Capacity:
200 lb (90.7 kg)
NOTE: Read entire instruction sheet before you start installation and assembly.
WARNING
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US
customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact
your local distributor.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
• Never exceed the Maximum UL Load Capacity.
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of
an "edge to edge" stud fi nder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws fi rmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal
injury.
2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerlessmounts.com
ISSUED: 08-20-02 SHEET #: 200-9405-12 11-18-11
A
Before you begin, make sure all parts shown are included with your product.
Parts List
PLCM-1CP PLCM-UNL-CP
Description Qty
ceiling arm box
tilt bracket 1 200-1552 200-1552
B
33" support pipe 1 139-1088 139-1088
C
retaining collar 1 1800-375 1800-375
D
M5 x 10 mm penta-pin™ screw 4 505-9010 505-9010
E
.062" fiber washer 1 540-9432 540-9432
F
M10 x 15 mm penta-pin screw
G
M10 penta-pin tool 1 520-9260 520-9260
H
M5 penta-pin tool 1 520-9249 520-9249
I
M5 x 8 mm phillips Type F screw 4 520-1167 520-1167
J
ceiling plate 1 128-1039 128-1039
K
ceiling plate end cap 2 2PT-22CA01D 2PT-22CA01D
L
wood screw 4 5S1-015-C03 5S1-015-C03
M
Parts may appear slightly different than illustrated.
Part # Part #
1
201-1062 201-1062
8
520-9263 520-9263
DFA
B
GJEH
I
K
L
M
C
2 of 10
ISSUED: 08-20-02 SHEET #: 200-9405-12 11-18-11
A
Parts List
PLCM-1CP PLCM-UNL-CP
Description Qty
adapter plate
A
shallow vertical brackets 2 - 201-1511
BB
M5 x 10 mm socket pin screw 4 - 520-1063
CC
M10 x 15 mm socket screws 4 - 520-9262
DD
6 mm allen wrench 1 - 560-9716
EE
4mm allen wrench 1 - 560-9646
FF
Part # Part #
1
- 201-1110
AA
M4 x 12 mm (6)
510-1079
BB
EE
Security Adapter Bracket Fasteners
M5 x 12 mm (4)
520-1064
M6 x 12 mm (4)
520-1050
M8 x 15 mm (6)
520-1068
M6 x 20 mm (4)
FF
520-9554
CC
DD
M5 x 25 mm (4)
520-1122
M4 x 25 mm (4)
510-1082
M6 x 30 mm (4)
520-1067
I.D. .22" (5.6 mm) (4)
540-1057
M6 x 25 mm (4)
520-1211
I.D. .34" (8.7 mm ) (4)
540-1059
M8 x 25 mm (4)
520-1101
3 of 10
multi-washer (6)
580-1036
M8 x 40 mm (4)
520-1152
ISSUED: 08-20-02 SHEET #: 200-9405-12 11-18-11
Installing Adapter Brackets
WARNING
• Tighten screws so adapter brackets are fi rmly attached. Do not tighten with excessive force. Overtightening can
cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become
detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.
• If screws don't get three complete turns in the display inserts or if screws bottom out and bracket is still not tightly
secured, damage may occur to display or product may fail.
To prevent scratching the display, set a cloth on a fl at, level surface that will support the weight of the display.
1
Place display face side down. If display has knobs on the back, remove them to allow the adapter brackets to be
attached. Place adapter brackets (BB) on back of display, align to holes, and center on back of display as shown
below. Attach the adapter brackets to the back of the display using the appropriate combination of screws, multiwashers and spacers as shown in step 1-1 and step 1-2.
NOTE: Top and bottom holes on display must always be used.
Verify that all holes are properly aligned, and then tighten screws using a phillips screwdriver.
NOTE: Tighten using security allen wrench (FF).
X
BB
Notes:
• The number of fasteners used will vary,
depending upon the type of display.
• Multi-washers and spacers may not be
used, depending upon the type of display.
• Use the corresponding hole in the multi-
washer that matches your screw size as
shown.
CENTER BRACKETS
VERTICALLY ON BACK OF
DISPLAY
X
Note: "X" dimensions should be equal.
MULTI-WASHER
MEDIUM HOLE FOR M5 SCREWS
SMALL HOLE FOR M4 SCREWS
LARGE HOLE FOR M6 SCREWS
NOTE: For fl at back displays proceed to step 1-1. For bump-out or recessed back display skip to step 1-2.
4 of 10
ISSUED: 08-20-02 SHEET #: 200-9405-12 11-18-11
For Flat Back Display
1-1
Begin with the shortest length screw, hand thread through multi-washer and adapter bracket into display as
shown below. Screw must make at least three full turns into the mounting hole and fi t snug into place. Do not
over tighten. If screw cannot make three full turns into the display, select a longer length screw from the baffl ed
fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws.
NOTE: Spacers may not be used, depending upon the type of display.
If you have any questions, please call Peerless customer care at 1-800-865-2112.
DISPLAY
MULTI-WASHER
SCREW
ADAPTER
BRACKET
(BB)
For Bump-out or Recessed Back Display
1-2
Begin with longer length screw, hand thread through multi-washer, adapter bracket and spacer in that order into
display as shown below. Screw must make at least three full turns into the mounting hole and fi t snug into place.
Do not over tighten. If screw cannot make three full turns into the display, select a longer length screw from the
baffl ed fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws.
DISPLAY
SPACER
If you have any questions, please call Peerless customer care at 1-800-865-2112.
MULTI-WASHER
SCREW
ADAPTER
BRACKET
(BB)
5 of 10
ISSUED: 08-20-02 SHEET #: 200-9405-12 11-18-11
For Wood Joist Finished Ceiling, Exposed Wood
2
Joists, or Wood Beam Ceiling. Drill four 5/32"
(4 mm) dia. holes to a minimum depth of 2.5"(64
mm) INTO JOIST CENTERS. Attach ceiling plate
(K) with four wood screws (M) using a 3/8"(10 mm)
socket wrench. Tighten wood screws (M) so ceiling
plate is fi rmly attached. Snap end caps (L) into
place.
WARNING
• Tighten wood screws so that ceiling plate is fi rmly
attached, but do not overtighten. Overtightening
can damage screws, greatly reducing their holding
power.
• Never tighten in excess of 80 in • lb (9 N.M.).
• Make sure that mounting screws are anchored into
the center of the joists. The use of an "edge to edge"
stud fi nder is highly recommended.
For Concrete Ceilings drill four 5/16"(8 mm) dia.
2
holes to a minimum depth of 1 3/4" (45 mm). Attach
ceiling plate (K) using concrete expansion anchors
as shown in 2-1 and 2-2. Then snap end caps (L)
into place.
Align hole in ceiling plate with hole in ceiling.
Gently hammer in concrete anchor.
Use a 10 mm wrench to tighten concrete anchor
to 80 in • lb (9 N.M.) maximum torque to expand
anchors.
FOR PRODUCT SAFETY USE ONLY RAWL
#5005 OR HILTI™ HL814 CONCRETE ANCHORS.
Order accessory kit #ACC210 which contains four
.312 x 1.625 concrete expansion anchors.
™
L
K
M
ACC210
2-1 2-2
WARNING
• Always attach concrete expansion anchors directly
to load-bearing concrete.
• Never attach concrete expansion anchors to
concrete covered with plaster, drywall, or other
fi nishing material.
6 of 10
PLASTER/
DRYWALL
CONCRETE
ISSUED: 08-20-02 SHEET #: 200-9405-12 11-18-11
Installing Adapter Bracket
Using the hole pattern shown below, attach adapter plate (AA) to tilt bracket (B) with four M10 x 15 mm screws (G).
3
Tighten screws using M10 penta-pin tool (H).
G
B
AA
7 of 10
ISSUED: 08-20-02 SHEET #: 200-9405-12 11-18-11
Thread support pipe (C) into threaded fi tting in ceiling plate (K). Align with one small hole in the side of the ceiling
4
plate threaded fi tting. Insert and tighten one M5 x 10 mm penta-pin screw (E) as shown. Tighten screw using M5
penta-pin tool (I). Insert four M10 x 15 mm penta-pin screws (G) into threaded holes in the sides of ceiling arm box
(A). Leave approximately 1/4" of exposed thread. Slide ceiling arm box (A) and fi ber washer (F) onto end of support
pipe. Thread retaining collar (D) onto support pipe. Allow ceiling arm box (A) to rest on top of retaining collar (D).
Insert and tighten one M5 x 10 mm penta-pin screw (E) into retaining collar (D) as shown. Insert one M5 x 10 mm
penta-pin screw (E) through the tab on the back of ceiling arm box (A). Use M5 penta-pin tool (I) to tighten screws.
Do not over tighten.
Note: UL Listed AEC or EXT extension column series can be used in combination with, or in place of support pipe
(C) to achieve different lengths.
K
D
C
F
A
E
E
BACK OF
CEILING
ARM BOX
G
G
1/4"
D
8 of 10
E
ISSUED: 08-20-02 SHEET #: 200-9405-12 11-18-11
Hang tilt bracket (B) onto ceiling arm box (A). Adjust tilt as desired and tighten four M10 x 15 mm penta-pin screws
5
(G) using M10 penta-pin tool (H).
WARNING
• For a safe assembly be sure to fully tighten four
screws (G).
B
A
9 of 10
G
ISSUED: 08-20-02 SHEET #: 200-9405-12 11-18-11
Mounting and Removing Flat Panel Display
WARNING
• Always use an assistant or mechanical lifting equipment to safely lift and position the plasma television.
Hook adapter brackets (BB) onto universal PLP plate (AA), then slowly swing display in as shown. Turn safety/
6
security screws clockwise at least six times to prevent display from being removed as shown in detail 1.
Tighten all fasteners using wrench (FF).
Display can be adjusted horizontally if desired as shown in fi gure 6.1.
NOTE: To lock the display down, tighten safety/security screws to adapter bracket as shown in detail 1.
To remove display from mount, loosen safety/security screws, swing display away from mount, and lift display off of
mount.
Fig. 6.1
SAFETY/SECURITY
SCREWS
BB
AA
AA
BB
DETAIL 1
10 of 10
All other brand and product names are trademarks or registered trademarks of their respective owners.
ISSUED: 08-20-02 SHEET #: 200-9405-12 11-18-11
© 2011, Peerless Industries, Inc. All rights reserved.
Loading...