Ohaus Corporation
29 Hanover Road Florham Park NJ 07932-0900
DS Series
Electronic Digital
Bench Scales
Instruction Manual
Unauthorized changes or modifications to this equipment are not permitted. See manual for replacement parts.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
This Class A, digital apparatus meets all requirements of the Canadian Interference. Causing Equipment Regulations.
Cet appareil numerique de la classe A respecte toutes les exigences du Reglement sur le material broilleur du Canada.
This device corresponds to requirements stipulated in 90/384/EEC and features radio interference suppression in compliance with valid EC Regulation 89/336/EEC. Note: The displayed value may be adversely affected under extreme electromagnetic influences, eg. when using a radio unit in the immediate vicinity of the device. Once the interference has been
rectified, the product can once again be used for its intended purpose. The device may have to be switched on again.
Cet appareil correspond aux exigences selon la norme 90/384/CEE et est déparasité conformément à la directive de la CE 89/336/CEE en vigueur. Remarque: Dans des conditions d’influences électromagnétiques extrêmes, par exemple en cas d’exploitation d’un appareil radio à proximité immédiate de I’appareil la valeur d’affichage risque d’être influencée. Une fois que l’influence parasite est terminée, le produit peut être de nouveau utilisé de manière conforme aux prescriptions; le cas échéant, il est nécessaire de le remettre en marche.
Dieses Gerät entspricht den Anforderungen nach 90/384/EWG und ist funkentstört
..
entsprechend der geltenden EG-Richtlinie 89/336/EWG. Hinweis: Unter extremen
..
elektromagnetischen Einflüssen z.B. bei Betreiben eines Funkgerätes in unmittelbarer Nähe des Gerätes kann eine Beeinflussung des Anzeigewertes verursacht werden. Nach Ende des Störeinflusses ist das Produkt wieder bestimmungsgemäss benutzbar, ggfs. ist ein Wiedereinschalten erforderlich.
2
TABLE OF CONTENTS |
|
INTRODUCTION .................................................................................................. |
4 |
DESCRIPTION ..................................................................................................... |
4 |
UNPACKING ........................................................................................................ |
5 |
INSTALLATION .................................................................................................... |
5 |
Leveling ......................................................................................................... |
5 |
Power Options .............................................................................................. |
5 |
AC Adapter ................................................................................................... |
6 |
OPERATION ........................................................................................................ |
6 |
Turning the Scale ON ................................................................................... |
6 |
Turning the Scale OFF ................................................................................. |
6 |
Checking Calibration ..................................................................................... |
7 |
Weighing ....................................................................................................... |
7 |
Taring ............................................................................................................ |
8 |
Calibration ..................................................................................................... |
9 |
Changing Units kg/lb ................................................................................... |
10 |
CARE AND MAINTENANCE ............................................................................. |
11 |
TROUBLESHOOTING ....................................................................................... |
11 |
Error Messages .......................................................................................... |
12 |
SPECIFICATIONS ............................................................................................. |
12 |
SERVICE INFORMATION ................................................................................. |
13 |
PARTS INFORMATION ..................................................................................... |
13 |
REPLACEMENT PARTS ................................................................................... |
13 |
ACCESSORIES ................................................................................................. |
13 |
LIMITED WARRANTY ....................................................................................... |
14 |
3
INTRODUCTION
This manual covers installation, operation and troubleshooting for the Ohaus DS Series Bench Scales, Models DS4, DS10, DS10L, DS20L and DS44L. To ensure proper operation of the scale, please read this manual completely.
DESCRIPTION
The Ohaus DS Series Bench Scales are precision industrial weighing instruments which can be used for almost any application with capacities from 44 to 440 pounds or 20 to 200 kilograms. The scale is designed to provide years of service with virtually no maintenance. The DS series indicator is constructed using an extruded aluminum housing which is anodized, contains a one piece PC board, a five digit LCD display which is 0.8 inches in height. The indicator is connected to the platform by a coiled cord and can be positioned up to eight feet from the platform for ease of viewing. The platforms on Models DS4 and DS10 are constructed of stainless steel, and painted steel on Models DS10L, DS20L and DS44L. The platforms are rugged and easily cleaned. Power is supplied through an AC Adapter/Charger which is available in three configurations for world-wide usage. An internal Nickel Cadmium battery powers the indicator, is rechargable and provides up to eight hours operation. Typical recharge time is seven hours. Accessories include a tower to support the indicator at a higher position to permit easier viewing of the display on the indicator. An indicator wall mount is included with the DS Series Bench Scales.
DS Series Electronic Digital Bench Scale
4
Loading...