MSI FM2-A85XA- G65 User Manual [ru]

FM2 -A85XA-G65

series MS-7793 (v1.x) Mainboard

Europe version

G52-77931X2

Preface

Copyright Notice

The material in this document is the intellectual property of MICRO-STAR INTERNA - TIONAL. We take every care in the preparation of this document, but no guarantee is given as to the correctness of its contents. Our products are under continual improvement and we reserve the right to make changes without notice.

Trademarks

All trademarks in this manual are properties of their respective owners.

MSI® is registered trademark of Micro-Star Int’l Co.,Ltd.

NVIDIA® is registered trademark of NVIDIA Corporation.

ATI® is registered trademark of AMD Corporation.

AMD® is registered trademarks of AMD Corporation.

Intel® is registered trademarks of Intel Corporation.

Windows® is registered trademarks of Microsoft Corporation.

AMI® is registered trademark of American Megatrends Inc.

Award® is a registered trademark of Phoenix Technologies Ltd.

Sound Blaster® is registered trademark of Creative Technology Ltd.

Realtek® is registered trademark of Realtek Semiconductor Corporation.

JMicron® is registered trademark of JMicron Technology Corporation.

Netware® is registered trademark of Novell, Inc.

Lucid® is trademark of LucidLogix Technologies, Ltd.

VIA® is registered trademark of VIA Technologies, Inc.

ASMedia® is registered trademark of ASMedia Technology Inc.

iPad, iPhone, and iPod are trademarks of Apple Inc.

Revision	History
Revision	Revision History	Date
V1.0	First release for PCB 1.X	2012/ 08

ii

MS-7793

Technical Support

If a problem arises with your system and no solution can be obtained from the user’s manual, please contact your place of purchase or local distributor. Alternatively, please try the following help resources for further guidance.

Visit the MSI website for technical guide, BIOS updates, driver updates, and other information:

http://www.msi.com/service/download

Contact our technical staff at:

http://support.msi.com

Safety Instructions

Always read the safety instructions carefully.

Keep this User’s Manual for future reference.

Keep this equipment away from humidity.

Lay this equipment on a reliable flat surface before setting it up.

The openings on the enclosure are for air convection hence protects the equipment from overheating. DO NOT COVER THE OPENINGS.

Make sure the voltage of the power source is at 110/220V before connecting the equipment to the power inlet.

Place the power cord such a way that people can not step on it. Do not place anything over the power cord.

Always Unplug the Power Cord before inserting any add-on card or module.

All cautions and warnings on the equipment should be noted.

Never pour any liquid into the opening that can cause damage or cause electrical shock.

If any of the following situations arises, get the equipment checked by service personnel:

The power cord or plug is damaged.

Liquid has penetrated into the equipment.

The equipment has been exposed to moisture.

The equipment does not work well or you can not get it work according to User’s Manual.

The equipment has been dropped and damaged.

The equipment has obvious sign of breakage.

DONOTLEAVETHISEQUIPMENTINANENVIRONMENTABOVE60oC(140oF), IT MAY DAMAGE THE EQUIPMENT.

Preface

iii

Preface

FCC -B Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the measures listed below.

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/television technician for help. Notice 1

The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Notice 2

Shielded interface cables and A.C. power cord, if any, must be used in order to comply with the emission limits.

VOIR LA NOTICE D’INSTALLATION AVANT DE RACCORDER AU RESEAU.

Micro-Star International

MS-7793

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1)this device may not cause harmful interference, and

2)this device must accept any interference received, including interference that may cause undesired operation.

CE Conformity

Hereby, Micro-Star International CO., LTD declares that this device is in compliance with the essential safety requirements and other relevant provisions set out in the European Directive.

iv

MS-7793

Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment and its antenna should be installed and operated with minimum distance 20 cm between the radiator and your body. This equipment and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.

European Community Compliance Statement

The equipment complies with the RF Exposure Requirement 1999/519/EC, Council Recommendation of 12 July 1999 on the limitation of exposure of the general public to electromagnetic fields (0–300GHz). This wireless device complies with the R&TTE Directive.

Taiwan Wireless Statements

率、加大功率或變更原設計之特性及功能。

電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之 干擾。

:

Japan VCCI Class B Statement

B

VCCIB

Korea Warning Statements

Preface

Preface

Battery Information

European Union:

Batteries, battery packs, and accumulators should not be disposed of as unsorted household waste. Please use the public collection system to return, recycle, or treat them in compliance with the local regulations.

Taiwan:

For better environmental protection, waste batteries should be collected separately for recycling or special disposal.

California, USA:

The button cell battery may contain perchlorate material and requires special handling when recycled or disposed of in California.

For further information please visit: http://www.dtsc.ca.gov/hazardouswaste/perchlorate/

CAUTION: There is a risk of explosion, if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the manufacturer.

Chemical Substances Information

Incompliancewithchemicalsubstancesregulations,suchastheEUREACHRegulation (Regulation EC No. 1907/2006 of the European Parliament and the Council), MSI provides the information of chemical substances in products at:

http://www.msi.com/html/popup/csr/evmtprtt_pcm.html

vi

MS-7793

WEEE (Waste Electrical and Electronic Equipment) Statement

ENGLISH

To protect the global environment and as an environmentalist, MSI must re-

mind you that...

Under the European Union (“EU”) Directive on Waste Electrical and Electron-

ic Equipment, Directive 2002/96/EC, which takes effect on August 13, 2005, products of “electrical and electronic equipment” cannot be discarded as municipal wastes anymore, and manufacturers of covered electronic equipment

will be obligated to take back such products at the end of their useful life. MSI will comply with the product take back requirements at the end of life of MSI-branded products that are sold into the EU. You can return these products to local collection points.

DEUTSCH

Hinweis von MSI zur Erhaltung und Schutz unserer Umwelt

Gemäß der Richtlinie 2002/96/EG über Elektround Elektronik-Altgeräte dürfen Elektro- und Elektronik-Altgeräte nicht mehr als kommunale Abfälle entsorgt werden. MSI hat europaweit verschiedene Sammelund Recyclingunternehmen beauftragt, die in die Europäische Union in Verkehr gebrachten Produkte, am Ende seines Lebenszyklus zurückzunehmen. Bitte entsorgen Sie dieses Produkt zum gegebenen Zeitpunkt ausschliesslich an einer lokalen Altgerätesammelstelle in Ihrer Nähe.

FRANÇAIS

En tant qu’écologiste et afin de protéger l’environnement, MSI tient à rappeler ceci...

Au sujet de la directive européenne (EU) relative aux déchets des équipement électriques et électroniques, directive 2002/96/EC, prenant effet le 13 août 2005, que les produits électriques et électroniques ne peuvent être déposés dans les décharges ou tout simplement mis à la poubelle. Les fabricants de ces équipements seront obligés de récupérer certains produits en fin de vie. MSI prendra en compte cette exigence relative au retour des produits en fin de vie au sein de la communauté européenne. Par conséquent vous pouvez retourner localement ces matériels dans les points de collecte.

РУССКИЙ

Компания MSI предпринимает активные действия по защите окружающей среды, поэтому напоминаем вам, что....

В соответствии с директивой Европейского Союза (ЕС) по предотвращению загрязнения окружающей среды использованным электрическим и электронным оборудованием (директива WEEE 2002/96/EC), вступающей в силу 13

августа 2005 года, изделия, относящиеся к электрическому и электронному оборудованию, не могут рассматриваться как бытовой мусор, поэтому производители вышеперечисленного электронного оборудования обязаны принимать его для переработки по окончании срока службы. MSI обязуется соблюдать требования по приему продукции, проданной под маркой MSI на территории EC, в переработку по окончании срока службы. Вы можете вернуть эти изделия в специализированные пункты приема.

vii

Preface

Preface

ESPAÑOL

MSI como empresa comprometida con la protección del medio ambiente, recomienda:

Bajo la directiva 2002/96/EC de la Unión Europea en materia de desechos y/o equipos electrónicos, con fecha de rigor desde el 13 de agosto de 2005, los productos clasificados como “eléctricos y equipos electrónicos” no pueden ser depositados en los contenedores habituales de su municipio, los fabricantes de equipos electrónicos, están obligados a hacerse cargo de dichos productos al termino de su período de vida. MSI estará comprometido con los términos de recogida de sus productos vendidos en la Unión Europea al final de su periodo de vida. Usted debe depositar estos productos en el punto limpio establecido por el ayuntamiento de su localidad o entregar a una empresa autorizada para la recogida de estos residuos.

NEDERLANDS

Om het milieu te beschermen, wil MSI u eraan herinneren dat….

De richtlijn van de Europese Unie (EU) met betrekking tot Vervuiling van Electrische en Electronische producten (2002/96/EC), die op 13 Augustus 2005 in zal gaan kunnen niet meer beschouwd worden als vervuiling. Fabrikanten van dit soort producten worden verplicht om producten retour te nemen aan het eind van hun levenscyclus. MSI zal overeenkomstig de richtlijn handelen voor de producten die de merknaam MSI dragen en verkocht zijn in de EU. Deze goederen kunnen geretourneerd worden op lokale inzamelingspunten.

SRPSKI

Da bi zaštitili prirodnu sredinu, i kao preduzeće koje vodi računa o okolini i prirodnoj sredini, MSI mora da vas podesti da…

Po Direktivi Evropske unije (“EU”) o odbačenoj ekektronskoj i električnoj opremi, Direktiva 2002/96/EC, koja stupa na snagu od 13. Avgusta 2005, proizvodi koji spadaju pod “elektronsku i električnu opremu” ne mogu više biti odbačeni kao običan otpad i proizvođači ove opreme biće prinuđeni da uzmu natrag ove proizvode na kraju njihovog uobičajenog veka trajanja. MSI će poštovati zahtev o preuzimanju ovakvih proizvoda kojima je istekao vek trajanja, koji imaju MSI oznaku i koji su prodati u EU. Ove proizvode možete vratiti na lokalnim mestima za prikupljanje.

POLSKI

Aby chronić nasze środowisko naturalne oraz jako firma dbająca o ekologię, MSI przypomina, że...

Zgodnie z Dyrektywą Unii Europejskiej (“UE”) dotyczącą odpadów produktów elektrycznych i elektronicznych (Dyrektywa 2002/96/EC), która wchodzi w życie 13 sierpnia 2005, tzw. “produkty oraz wyposażenie elektryczne i elektroniczne “ nie mogą być traktowane jako śmieci komunalne, tak więc producenci tych produktów będą zobowiązani do odbierania ich w momencie gdy produkt jest wycofywany z użycia. MSI wypełni wymagania UE, przyjmując produkty (sprzedawane na terenie Unii Europejskiej) wycofywane z użycia. Produkty MSI będzie można zwracać w wyznaczonych punktach zbiorczych.

viii

MS-7793

TÜRKÇE

Çevreci özelliğiyle bilinen MSI dünyada çevreyi korumak için hatırlatır:

Avrupa Birliği (AB) Kararnamesi Elektrik ve Elektronik Malzeme Atığı, 2002/96/EC Kararnamesi altında 13 Ağustos 2005 tarihinden itibaren geçerli olmak üzere, elektrikli ve elektronik malzemeler diğer atıklar gibi çöpe atılamayacak ve bu elektonik cihazların üreticileri, cihazların kullanım süreleri bittikten sonra ürünleri geri toplamakla yükümlü olacaktır. Avrupa Birliği’ne satılan MSI markalı ürünlerin kullanım süreleri bittiğinde MSI ürünlerin geri alınması isteği ile işbirliği içerisinde olacaktır. Ürünlerinizi yerel toplama noktalarına bırakabilirsiniz.

ČESKY

Záleží nám na ochraně životního prostředí - společnost MSI upozorňuje...

Podle směrnice Evropské unie (“EU”) o likvidaci elektrických a elektronických výrobků 2002/96/EC platné od 13. srpna 2005 je zakázáno likvidovat “elektrické a elektronické výrobky” v běžném komunálním odpadu a výrobci elektronických výrobků, na které se tato směrnice vztahuje, budou povinni odebírat takové výrobky zpět po skončení jejich životnosti. Společnost MSI splní požadavky na odebírání výrobků značky MSI, prodávaných v zemích EU, po skončení jejich životnosti. Tyto výrobky můžete odevzdat v místních sběrnách.

MAGYAR

Annak érdekében, hogy környezetünket megvédjük, illetve környezetvédőként fellépve az MSI emlékezteti Önt, hogy ...

Az Európai Unió („EU”) 2005. augusztus 13-án hatályba lépő, az elektromos és elektronikus berendezések hulladékairól szóló 2002/96/EK irányelve szerint az elektromos és elektronikus berendezések többé nem kezelhetőek lakossági hulladékként, és az ilyen elektronikus berendezések gyártói kötelessé válnak az ilyen termékek visszavételére azok hasznos élettartama végén. Az MSI betartja a termékvisszavétellel kapcsolatos követelményeket az MSI márkanév alatt az EU-n belül értékesített termékek esetében, azok élettartamának végén. Az ilyen termékeket a legközelebbi gyűjtőhelyre viheti.

ITALIANO

Per proteggere l’ambiente, MSI, da sempre amica della natura, ti ricorda che….

In base alla Direttiva dell’Unione Europea (EU) sullo Smaltimento dei Materiali Elettrici ed Elettronici, Direttiva 2002/96/EC in vigore dal 13 Agosto 2005, prodotti appartenenti alla categoria dei Materiali Elettrici ed Elettronici non possono più essere eliminati come rifiuti municipali: i produttori di detti materiali saranno obbligati a ritirare ogni prodotto alla fine del suo ciclo di vita. MSI si adeguerà a tale Direttiva ritirando tutti i prodotti marchiati MSI che sono stati venduti all’interno dell’Unione Europea alla fine del loro ciclo di vita. È possibile portare i prodotti nel più vicino punto di raccolta

Preface

ix

Preface

Contents

Copyright	Notice	ii
Trademarks		ii
Revision	History	ii
Technical	Support	iii
Safety Instructions		iii
FCC-B Radio Frequency Interference Statement		iv
CE Conformity		iv
Radiation Exposure Statement		v
European Community Compliance Statement		v
Taiwan Wireless Statements		v
Japan VCCI Class B Statement		v
Korea Warning Statements		v
Battery Information		vi
Chemical Substances Information		vi
WEEE (Waste Electrical and Electronic Equipment) Statement		vii
English		En-1

Mainboard Specifications En-2

Connectors Quick Guide En-4

Back Panel Quick Guide En-6

APU (Accelerated Processing Units) En-8

Mounting Screw Holes En-11

Power Supply En-12

Memory En-13

Expansion Slot En-15

Internal Connectors En-16

Jumper En-25

Buttons En-26

Drivers and Utilities En-29

BIOS Setup En-30

Install Windows XP Notes En-40

MS-7793

Deutsch De-1

Spezifikationen De-2 Anschlussübersicht De-4 Rücktafel-Übersicht De-6 APU (Accelerated Processing Units) De-8 Schraubenlöcher für die Montage De-11 Stromversorgung De-12 Speicher De-13 Erweiterungssteckplätze De-15 Interne Anschlüsse De-16 Steckbrücken De-25 Tasten De-26 Treiber und Dienstprogramme De-29 BIOS Setup De-30 Hinweise zur Windows XP-Installation De-40

Français Fr -1

Spécifications Fr-2 Guide Rapide Des Connecteurs Fr-4 Guide rapide du panneau arrière Fr-6 Processeur APU (Accelerated Processing Units) Fr-8 Trous Taraudés de Montage Fr-11 Connecteurs d’alimentation Fr-12 Mémoire Fr-13 Emplacements d’extension Fr-15 Connecteurs internes Fr-16 Cavaliers Fr-25 Boutons Fr-26 Pilotes et Utilitaires Fr-29 Réglage BIOS Fr-30 Remarques d’Installion Windows XP Fr-40

Preface

xi

Preface

Русский Ru-1

Характеристики системной платы Ru-2 Краткое руководство по разъемам Ru-4 Краткое руководство по работе с задней панелью Ru-6 APU (Accelerated Processing Units) Ru-8 Отверстия под установочные винты Ru-11 Электропитание Ru-12 Память Ru-13 Слоты расширения Ru-15 Внутренние разъемы Ru-16 Перемычки Ru-25 Кнопки Ru-26 Драйверы и утилиты Ru-29 Настройка BIOS Ru-30 Установка Windows XP Примечания Ru-40

xii

English

FM2 -A85XA-G65

Series

MS-7793 Mainboard

Mainboard Specifications

Processor Support

■ AMD® A10/A8/A6/A4-series processors for the FM2 socket

Chipset

■ AMD® A85X chipset

Memory Support

■4x DDR3 DIMMs support for DDR3-1066/1333/1600/1866 MHz up to 32GB max

■Supports Dual-Channel mode

LAN

■ Supports LAN 10/100/1000 Fast Ethernet by Realtek® 8111E

Audio

■Integrated HD audio codec by Realtek® ALC892

■8-channel audio with jack sensing

■Compliant with Azalia 1.0 Spec

SATA

■ 8x SATA 6Gb/s ports by AMD® A85X

RAID

■ SATA1~8 support RAID 0/ 1/ 5/ 10 mode by AMD® A85X

USB 3.0

■2x USB 3.0 rear I/O ports by AMD® A85X

■1x USB 3.0 onboard connector by AMD® A85X

Multi-GPU

■ Supports AMD® CrossFire™ Technology

Dual-Graphics

■Supports AMD® Dual Graphics Technology

-Please visit the AMD official website to find the supported Dual Graphics combinations of APU and discrete GPU for achieving this technology.

-A4-series APU doesn't support Dual Graphics technology.

Connectors & Buttons

■Back panel

-1x PS/2 keyboard/ mouse combo port

-4x USB 2.0 ports

-1x LAN port

-1x VGA port**, supporting a maximum resolution of 1920x1200@60 Hz

-1x dual link DVI-D port**, supports a maximum resolution of 2560x1600@60 Hz

-1x Optical S/PDIF-out port

-1x HDMI port**, supporting a maximum resolution of 1920x1080@60 Hz

-1x DisplayPort**, supporting a maximum resolution of 2560x1600@60 Hz

-2x USB 3.0 ports

-6x audio ports

En-2

**This mainboard supports dual-display function by two onboard graphics output ports (HDMI+VGA, HDMI+DVI-D, VGA+DVI-D, VGA+DisplayPort & DVI-D+DisplayPort). **This mainboard also supports triple-display function by three onboard graphics output ports (HDMI+VGA+DVI-D & DisplayPort+VGA+DVI-D).

**Please note that, the HDMI port and DisplayPort can not be used simultaneously.

■On-Board

-3x USB 2.0 connector

-1x USB 3.0 connector

-1x TPM Module connector

-1x Front Panel Audio connector

-1x Chassis Intrusion connector

-1x Voice Genie connector

-1x MultiConnect Panel connector

-1x Power button

-1x Reset button

-1x OC Genie button

-1x Clear CMOS button

-1x Voltage Checkpoints connector

Slots

■2x PCIe 2.0 x16 slots

-PCI_E2 supports up to PCIe x16 speed (when PCI_E5 is empty) or PCIe x8 speed (when PCI_E5 is installed)

-PCI_E5 supports up to PCIe x8 speed

■3x PCIe 2.0 x1 slots

■2x PCI slots

Form Factor

■ ATX (30.5 cm X 24.5 cm)

Mounting Screw Holes

■ 9x mounting holes

For the latest information about processor, please visit http://www.msi.com/service/cpu-support

For more information on compatible components, please visit

http://www.msi.com/service/test-report

If you need to purchase accessories and request the part numbers, you could search the product web page and find details on our web address http://www.msi.com/index. php

Engl shi

En-3

MS-7793 Mainboard

Connectors Quick Guide

Back Panel

		DIMM1		SYSFAN3
SYSFAN2	APU		DIMM2
				DIMM3
JPWR2		CPUFAN		DIMM4

OC1

POWER1

RESET1

JTURBO1

FV1

JPWR1

	PCI_E1	SATA2
	PCI_E2	SATA7_8
	JCI1	SATA5_6
	PCI_E3
	PCI_E4	SATA3_4
	PCI_E5	SATA1
		JUSB4
	PCI1	SYSFAN1
		JBAT1
	PCI2	CLR_CMOS1
	JAUD1
		JFP1
	SYSFAN4	JFP2
	JTPM1	JUSB1
	JDLED3	JUSB2
		JUSB3

En-4

Connectors Reference Guide

Port Name	Port Type	Page
Back Panel	I/O Ports	En-6
APU	FM2 APU Socket	En-8
CLR_CMOS1	Clear CMOS Button	En-28
CPUFAN,SYSFAN1~4	Fan Power Connectors	En-17
DIMM1~4	DDR3 Memory Slots	En-13
FV1	Voltage Checkpoints Connector	En-24
JAUD1	Front Panel Audio Connector	En-21
JBAT1	Clear CMOS Jumper	En-25
JCI1	Chassis Intrusion Connector	En-22
JDLED3	Voice Genie Connector	En-23
JFP1, JFP2	Front Panel Connectors	En-18
JPWR1	ATX 24-pin Power Connector	En-12
JPWR2	ATX 8-pin Power Connector	En-12
JTPM1	TPM Module Connector	En-21
JTURBO1	MultiConnect Panel Connector	En-22
JUSB1~3	USB 2.0 Expansion Connectors	En-19
JUSB4	USB 3.0 Expansion Connector	En-20
OC1	OC Genie Button	En-26
PCI_E1, 3, 4	PCIe x1 Expansion Slots	En-15
PCI_E2, 5	PCIe x16 Expansion Slots	En-15
PCI1, 2	PCI Expansion Slots	En-15
POWER1	Power Button	En-27
RESET1	Reset Button	En-27
SATA1~8	SATA Connectors	En-16

Engl shi

En-5

MS-7793 Mainboard

Back Panel Quick Guide

Mouse/	LAN	VGA Port	Optical
Keyboard			S/PDIF-Out
			USB 3.0 Port	Line-In	RS-Out
				Line-Out CS-Out
			DisplayPort	Mic	SS-Out
USB 2.0 Port	USB 2.0 Port	DVI-D Port

HDMI Port

Mouse/Keyboard

A combination PS/2® mouse/keyboard DIN connector for a PS/2® mouse/keyboard.

LAN
The standard RJ-45 LAN jack is for connecting to a Yellow				Green/ Orange
Local Area Network (LAN).
LED	Color	LED State	Condition
Left	Yellow	Off	LAN link is not established.
		On(Steady)	LAN link is established.
		On(flashing)	The computer is communicating with another computer on the network.
Right	Green	Off	10 Mbits/sec data rate
		On	100 Mbits/sec data rate
	Orange	On	1000 Mbits/sec data rate

USB 2.0 Port

The USB 2.0 port is for attaching USB 2.0 devices such as keyboard, mouse, or other USB 2.0-compatible devices.

USB 3.0 Port

USB 3.0 port is backward-compatible with USB 2.0 devices. It supports data transfer rate up to 5 Gbit/s (SuperSpeed).

Important

In order to use USB 3.0 devices, you must connect to a USB 3.0 port. If a USB cable is used, it must be USB 3.0 compliant.

En-6

VGA Port

The DB15-pin female connector is provided for monitor.

DVI-D Port

The DVI-D (Digital Visual InterfaceDigital) connector can be connected to a LCD monitor, or a CRT monitor with an adapter. To connect a monitor, please refer to the monitor’s manual for more information.

HDMI Port

The High-Definition Multimedia Interface (HDMI) is an all-digital audio-video interface that is capable of transmitting uncompressed streams. HDMI supports all types of TV formats, including standard, enhanced, or high-definition video, plus multi-channel digital audio on a single cable.

DisplayPort Connector

DisplayPort is a digital display interface standard. This connector is used to connect a monitor with DisplayPort inputs.

Important

This mainboard supports dual-display / triple-display function by 2 / 3 onboard graphics output ports.

	Dual-display mode	Triple-display mode
	HDMI+DVI /
	HDMI+VGA /	VGA+DVI+HDMI /
	DVI+VGA /
		VGA+DVI+DisplayPort
	DVI+DisplayPort /
	VGA+DisplayPort

	Extend mode
	(Extend the desktop to the other monitor(s))
	Clone mode
	(All monitors show the same screen)

Optical S/PDIF-Out

This S/PDIF (Sony & Philips Digital Interconnect Format) connector is provided for digital audio transmission to external speakers through an optical fiber cable.

Audio Ports

These connectors are used for audio devices. The color of the jack refers to the function of the connector.

■Blue-Line in: Used for connecting external audio outputting devices.

■GreenLine out: Used as a connector for speakers or headphone.

■PinkMic: Used as a connector for a microphone.

■Black- RS-Out: Rear surround sound line out in 4/ 5.1/ 7.1 channel mode.

■Orange- CS-Out: Center/ subwoofer line out in 5.1/ 7.1 channel mode.

■Gray- SS-Out: Side surround sound line out in 7.1 channel mode.

Engl shi

En-7

MS-7793 Mainboard

APU (Accelerated Processing Units)

Introduction to FM2 APU

The surface of APU. Remember to apply some thermal paste on it for better heat dispersion.

Gold arrow

Important

Overheating

Overheating can seriously damage the APU and mainboard. Always make sure the cooling fans work properly to protect the APU from overheating. Be sure to apply an even layer of thermal paste (or thermal tape) between the APU and the heatsink to enhance heat dissipation.

Replacing the APU

When replacing the APU, always turn off the system’s power supply and unplug the power supply’s power cord to ensure the safety of the APU.

Overclocking

This mainboard is designed to support overclocking. Before attempting to overclock, please make sure that all other system components can tolerate overclocking. Any attempt to operate beyond product specifications is not recommend. MSI does not guarantee the damages or risks caused by inadequate operation beyond product specifications.

En-8

APU & Cooler Installation

When you are installing the APU, make sure the APU has a cooler attached on the top to prevent overheating. Meanwhile, do not forget to apply some thermal paste on APU before installing the heat sink/cooler fan for better heat dispersion.

Follow the steps below to install the APU & cooler correctly. Wrong installation will cause the damage of your APU & mainboard.

1. Pull the lever sideways away from	2. Look for the gold arrow of the APU.
the socket. Make sure to raise the	The gold arrow should point as
lever up to a 90-degree angle.	shown in the picture. The APU can
	only fit in the correct orientation.

Engl shi

3.If the APU is correctly installed, the pins should be completely embedded into the socket and can not be seen. Please note that any violation of the correct installation procedures may cause permanent damages to your mainboard.

4.Press the APU down firmly into the socket and close the lever. As the APU is likely to move while the lever is being closed, always close the leverwithyourfingerspressingtightly on top of the APU to make sure the APU is properly and completely embedded into the socket.

En-9

MS-7793 Mainboard

5.Position the cooling set onto the retention mechanism.

Hook one end of the clip to hook first.

7. Fasten down the lever.

6.Then press down the other end of the clip to fasten the cooling set on the top of the retention mechanism.

Locate the Fix Lever and lift up it .

8.Attach the APU Fan cable to the APU fan connector on the mainboard.

Important

•While disconnecting the Safety Hook from the fixed bolt, it is necessary to keep an eye on your fingers, because once the Safety Hook is disconnected from the fixed bolt, the fixed lever will spring back instantly.

•Confirm that the APU cooler has formed a tight seal with the APU before booting your system.

•Please refer to the documentation in the APU cooler package for more details about APU cooler installation.

En-10

Mounting Screw Holes

When installing the mainboard, first install the necessary mounting stands required for ngi a mainboard on the mounting plate in your computer case. If there is an I/O back plate that came withtowardthe computer case, please replace it with the I/O backplate that came

with the mainboard package. The I/O backplate should snap easily into the computer

case withouti the need for any screws. Align the mounting plate’s mounting stands with

the screw holes on the mainboard and secure the mainboard with the screws provided
	the
with your computer case. The locations of the screw holes on the mainboard are shown
	holesne
below. Forimore information, please refer to the manual that came with the computer
case.	thewonup
	I/O	the
	should		I/OThe
	backplate	the
	rear l
			ports
		of
	.		should
		computer
			be
			fac
		They .case

Engl shi

Important

•Install the mainboard on a flat surface free from unnecessary debris.

•To prevent damage to the mainboard, any contact between the mainboard circuitry and the computer case, except for the mounting stands, is prohibited.

•Please make sure there are no loose metal components on the mainboard or within the computer case that may cause a short circuit of the mainboard.

En-11

MS-7793 Mainboard

Power Supply

JPWR1: ATX 24-pin Power Connector

This connector allows you to connect an ATX 24-pin power supply. To connect the ATX 24-pin power supply, align the power supply cable with the connector and firmly press the cable into the connector. If done correctly, the clip on the power cable should be hooked on the mainboard’s power connector.

								12
							11				.
						7	10		. +3.
										+12V
						9 .						3V
						8	.
					6 .
				5 .
1			4		. +5
		3 .			Ground
2			. +5													24
		.GroundV
	.					V
. +3				3
+3
				.											23.
				V
		3																.
																			Ground
															. +5					V
															+5
															+5	V	V
													.Ground
												.		-
										13.		-		ON
											+3		12V		#
													3
													V

JPWR2: ATX 8-pin Power Connector

This connector provides 12V power to the APU.

			4
			.
		3	Ground
		.
	2	Ground
	.
1	Ground
.
Ground
						8
			5			.
					7	+12V
					.
				6	+12V
				.
				+12V
			.
			+12V

Important

Make sure that all the power cables are securely connected to a proper ATX power supply to ensure stable operation of the mainboard.

En-12

Memory

These DIMM slots are used for installing memory modules. For more information on compatible components, please visit http://www.msi.com/service/test-report

DDR3

240-pin, 1.5V

48x2=96 pin

72x2=144 pin

Dual-Channel mode Population Rule

In Dual-Channel mode, the memory modules can transmit and receive data with two data bus channels simultaneously. Enabling Dual-Channel mode can enhance system performance. The following illustrations explain the population rules for Dual-Channel mode.

1 DIMM1

DIMM2

DIMM3

DIMM4

2 DIMM1

DIMM2

DIMM3

DIMM4

Installed

Empty

Important

•DDR3 memory modules are not interchangeable with DDR2, and the DDR3 standard is not backward compatible. Always install DDR3 memory modules in DDR3 DIMM slots.

•To ensure system stability, memory modules must be of the same type and density.

•Due to chipset resource usage, the system will only detect up to 31+ GB of memory (not full 32 GB) when all DIMM slots have 8GB memory modules installed.

Engl shi

En-13

MS-7793 Mainboard

Installing Memory Modules

1.Unlock the DIMM slot by pushing the mounting clips to the side. Vertically insert the memory module into the DIMM slot. The memory module has an off-center notch on the bottom that will only allow it to fit one way into the DIMM slot.

2.Push the memory module deep into the DIMM slot. The plastic clips at each side of the DIMM slot will automatically close when the memory module is properly seated and an audible click should be heard.

3.Manually check if the memory module has been locked in place by the DIMM slot’s side clips.

Notch

Volt

En-14

Expansion Slot

Thismainboardcontainsnumerousportsforexpansioncards,suchasdiscretegraphics or audio cards.

PCIe Slot

The PCIe slot supports the PCIe interface expansion card.

PCIe 2.0 x16 Slot

PCIe 2.0 x1 Slot

PCI Slot

The PCI slot supports additional LAN, SCSI, USB, and other add-on cards that comply with PCI specifications.

32-bit PCI Slot

Important

When adding or removing expansion cards, always turn off the power supply and unplug the power supply power cable from the power outlet. Read the expansion card’s documentation to check for any necessary additional hardware or software changes.

PCI Interrupt Request Routing

IRQ, or interrupt request lines, are hardware lines over which devices can send interrupt requests to the processor. The PCI IRQ pins are typically connected to the PCI bus pins as followed:

	Order1	Order2	Order3	Order4
PCI1	INT E#	INT F#	INT G#	INT H#
PCI2	INT F#	INT G#	INT H#	INT E#

Engl shi

En-15

MS-7793 Mainboard

Internal Connectors

SATA1~8: SATA Connector

This connector is a high-speed SATA interface port. Each connector can connect to one SATA device. SATA devices include disk drives (HDD), solid state drives (SSD), and optical drives (CD/ DVD/ Blu-Ray).

SATA8

SATA6

SATA4

SATA2 SATA7

SATA5

SATA3

SATA1

* The MB layout in this figure is for reference only.

Important

•Many SATA devices also need a power cable from the power supply. Such devices include disk drives (HDD), solid state drives (SSD), and optical drives (CD / DVD / Blu-Ray). Please refer to the device’s manual for further information.

•Many computer cases also require that large SATA devices, such as HDDs, SSDs, and optical drives, be screwed down into the case. Refer to the manual that came with your computer case or your SATA device for further installation instructions.

•Please do not fold the SATA cable at a 90-degree angle. Data loss may result during transmission otherwise.

•SATA cables have identical plugs on either sides of the cable. However, it is recommended that the flat connector be connected to the mainboard for space saving purposes.

En-16

CPUFAN,SYSFAN1~4: Fan Power Connectors

The fan power connectors support system cooling fans with +12V. If the mainboard has a System Hardware Monitor chipset on-board, you must use a specially designed fan with a speed sensor to take advantage of the APU fan control. Remember to connect all system fans. Some system fans may not connect to the mainboard and will instead connect to the power supply directly. A system fan can be plugged into any available system fan connector.

CPUFAN

				1
		2 .
3			. G
				+ r
4	.					1 o
		S						2 u
.			e							n
C					n V						d
		o					s
			n					o
				t					r
						r
							o
								l

SYSFAN1/ 2

								1
2 .
								+12VGround
3 .
4 .
							Sensor
.
							No	Us
								e

SYSFAN3/ 4

		1
2 .
3	. G
		+ r
.		1	o
			u
N 2				n
		o			d
		U V
		s
		e

Important

•Please refer to your processor’s official website or consult your vendor to find recommended APU cooling fans.

•The CPUFAN connector supports Smart Fan Control with linear mode. The Control Center II utility can be installed to automatically control the fan speeds according to the APU’s temperature.

•If there are not enough ports on the mainboard to connect all system fans, adapters are available to connect a fan directly to a power supply.

•Before first boot up, ensure that there are no cables impeding any fan blades.

Engl shi

En-17

MS-7793 Mainboard

JFP1, JFP2: Front Panel Connectors

These connectors connect to the front panel switches and LEDs. The JFP1 connector is compliant with the Intel® Front Panel I/O Connectivity Design Guide. When installing the front panel connectors, please use the enclosed mConnectors to simplify installation. Plug all the wires from the computer case into the mConnectors and then plug the mConnectors into the mainboard.

Speaker			6			+
Buzzer
					8
					.
	4		.
				-
2	.
		+
.
-

JFP2

				7
	3		5 .
				. No
		.		Power
				Pi		D
1		Suspend
.					n
Ground					LE
					LE
						D

	P
P	ower		S	10
			witch					No
ower
							.				Pi
		LE						8
			D			6				-
			4					.	.
								+
			2	.
					-
			.
			+

JFP1

								9
1									.
					7					Reserve
			5			.
							+
	3		.
				-
		.
.		-								Reset				d
+
						HDD
											LE		S
												D		witch

Important

•On the connectors coming from the case, pins marked by small triangles are positive wires. Please use the diagrams above and the writing on the mConnectors to determine correct connector orientation and placement.

•The majority of the computer case’s front panel connectors will primarily be plugged into JFP1.

En-18