LG OLED65W8PUA Owner’s Manual

0 (0)

Safety and Reference

Please read this manual carefully before operating your TV and retain it for future reference.

OLED65W8PUA

OLED77W8PUA

*MFL70409203*

www.lg.com

(1804-REV00)	Copyright 2018 LG Electronics Inc. All Rights Reserved.
	Printed in Korea

<![if ! IE]>

<![endif]>ENGLISH

Important Safety Instruction

•• Read these instructions.

•• Keep these instructions.

•• Heed all warnings.

•• Follow all instructions.

•• Do not use this apparatus near water.

•• Clean only with dry cloth.

•• Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

•• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

•• Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

•• Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

•• Only use attachments/accessories specified by the manufacturer.

•• Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

•• Unplug this apparatus during lightning storms or when unused for long periods of time.

•• Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

By using this product, you agree that all disputes between you and LG arising out of or relating in any way to this product (including but not limited to warranty disputes) shall be resolved exclusively through binding arbitration on an individual basis. The terms of the arbitration agreement

(including details on the procedure for resolving disputes) is available at www.lg.com/us/arbitration (USA) or www.lg.ca/arbitration (Canada).

Warning! Safety Instructions

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

The symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s

enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The symbol is intended to alert the user to the presence of important operating and maintenance (servicing)

instructions in the literature accompanying the device.

WARNING: TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

•• TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OTHER ITEMS WITH OPEN FLAMES AWAY FROM THIS PRODUCT AT ALL TIMES.

•• Do not place the TV and/or remote control in the following environments:

-- Keep the product away from direct sunlight.

-- An area with high humidity such as a bathroom

-- Near any heat source such as stoves and other devices that produce heat.

-- Near kitchen counters or humidifiers where they can easily be exposed to steam or oil.

-- An area exposed to rain or wind.

-- Do not expose to dripping or splashing and do not place objects filled with liquids, such as vases, cups, etc. on or over the apparatus (e.g., on shelves above the unit).

-- Near flammable objects such as gasoline or candles, or expose the TV to direct air conditioning.

-- Do not install in excessively dusty places.

Otherwise, this may result in fire, electric shock, combustion/ explosion, malfunction or product deformation.

•• Ventilation

-- Install your TV where there is proper ventilation. Do not install in a confined space such as a bookcase.

-- Do not install the product on a carpet or cushion.

-- Do not block or cover the product with cloth or other materials while unit is plugged in.

•• Take care not to touch the ventilation openings. When watching the TV for a long period, the ventilation openings may become hot.

•• Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the device.

•• Do not move the TV whilst the Power cord is plugged in.

•• Do not use a damaged or loosely fitting power cord.

•• Be sure do grasp the plug when unplugging the power cord. Do not pull on the power cord to unplug the TV.

•• Do not connect too many devices to the same AC power outlet as this could result in fire or electric shock.

•• Disconnecting the Device from the Main Power

-- The power plug is the disconnecting device. In case of an emergency, the power plug must remain readily accessible.

•• Do not let your children climb or cling onto the TV. Otherwise, the TV may fall over, which may cause serious injury.

•• Outdoor Antenna Grounding (Can differ by country):

-- If an outdoor antenna is installed, follow the precautions below. An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits as death or serious injury can occur.

Be sure the antenna system is grounded to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code (NEC) in the U.S.A. provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements for the grounding electrode. Antenna grounding according to the National Electrical Code, ANSI/NFPA 70

<![if ! IE]>

<![endif]>ENGLISH

<![if ! IE]>

<![endif]>ENGLISH

•• Grounding (Except for devices which are not grounded.)

-- TV with a three-prong grounded AC plug must be connected to a three-prong grounded AC outlet. Ensure that you connect the earth ground wire to prevent possible electric shock.

•• Never touch this apparatus or antenna during a lightning storm. You may be electrocuted.

•• Make sure the power cord is connected securely to the TV and wall socket if not secured damage to the Plug and socket may occur and in extreme cases a fire may break out.

•• Do not insert metallic or inflammable objects into the product. If a foreign object is dropped into the product, unplug the power cord and contact the customer service.

•• Do not touch the end of the power cord while it is plugged in. You may be electrocuted.

•• If any of the following occur, unplug the product immediately and contact your local customer service.

-- The product has been damaged.

-- If water or another substance enters the product (like an AC adapter, power cord, or TV).

-- If you smell smoke or other odors coming from the TV.

-- When lightning storms or when unused for long periods of time.

Even the TV is turned off by remote control or button, AC power source is connected to the unit if not unplugged in.

•• Do not use high voltage electrical equipment near the TV (e.g., a bug zapper). This may result in product malfunction.

•• Do not attempt to modify this product in any way without written authorization from LG Electronics. Accidental fire or electric shock can occur. Contact your local customer service for service or repair. Unauthorized modification could void the user’s authority to operate this product.

•• Use only an authorized attachments / accessories approved by LG Electronics. Otherwise, this may result in fire, electric shock, malfunction, or product damage.

•• Never disassemble the AC adapter or power cord. This may result in fire or electric shock.

•• Handle the adapter carefully to avoid dropping or striking it. An impact could damage the adapter.

•• To reduce the risk of fire or electrical shock, do not touch the TV with wet hands. If the power cord prongs are wet or covered with dust, dry the power plug completely or wipe dust off.

•• Batteries

-- Store the accessories (battery, etc.) in a safe location out of the reach of children.

-- Do not short circuit, disassemble, or allow the batteries to overheat. Do not dispose of batteries in a fire. Batteries should not be exposed to excessive heat.

•• Moving

-- When moving, make sure the product is turned off, unplugged, and all cables have been removed. It may take 2 or more people to carry larger TVs. Do not press or put stress on the front panel of the TV. Otherwise, this may result in product damage, fire hazard or injury.

•• Keep the packing anti-moisture material or vinyl packing out of the reach of children.

•• Do not allow an impact shock, any objects to fall into the product, and do not drop anything onto the screen.

•• Do not press strongly upon the panel with a hand or a sharp object such as a nail, pencil, or pen, or make a scratch on it. It may cause damage to screen.

•• Cleaning

-- When cleaning, unplug the power cord and wipe gently with a soft/dry cloth. Do not spray water or other liquids directly on the TV. Do not clean your TV with chemicals including glass cleaner, any type of air freshener, insecticide, lubricants, wax (car, industrial), abrasive, thinner, benzene, alcohol etc., which can damage the product and/or its panel. Otherwise, this may result in electric shock or product damage.

Preparing

•• When the TV is turned on for the first time after being shipped from the factory, initialization of the TV may take approximately one minute.

• Image shown may differ from your TV.

• Your TV’s OSD (On Screen Display) may differ slightly from that shown in this manual.

• The available menus and options may differ from the input source or product model that you are using.

• New features may be added to this TV in the future.

• The device must be easily accessed to a location outlet near the access. Some devices are not made by turning on / off button, turning off the device and unplugging the power cord.

• The items supplied with your product may vary depending upon the model.

• Product specifications or contents of this manual may be changed without prior notice due to upgrade of product functions.

•• For an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm (0.39 inches) thick and 18 mm (0.7 inches) width.

•• Use an extension cable that supportsif the USB cable or USB flash drive does not fit into your TV’s USB port.

•• Use a certified cable with the HDMI logo attached. If you do not use a certified HDMI cable, the screen may not display or a connection error may occur.

•• Recommended HDMI cable types (3 m (9.84 ft) or less) -- High-Speed HDMI®/™ cable

-- High-Speed HDMI®/™ cable with Ethernet

	B	B	*A =< 10 mm (0.39 inches)
	B
A	A
A	A		=
			*B < 18 mm (0.7 inches)

•• Make sure to wring any excess water or cleaner from the cloth.

•• Do not spray water or cleaner directly onto the TV screen.

•• Make sure to spray just enough of water or cleaner onto a dry cloth to wipe the screen.

Optional Extras

Optional extras can be changed or modified for quality improvement without any notification. Contact your dealer for buying these items. These devices work only with certain models. The model name or design may be changed due to the manufacturer’s circumstances or policies.

The manufacturer shall not be held responsible for any injuries, damages, or quality issues that may arise if an item that is not listed below is purchased separately and used.

Magic Remote Control

(Depending upon model)

AN-MR18BA

Check whether your TV model supports Bluetooth in the Wireless Module Specification to verify whether it can be used with the Magic Remote.

Companion Box (AV box) Wall mount

(Depending upon model)

W7AWB

<![if ! IE]>

<![endif]>ENGLISH

<![if ! IE]>

<![endif]>ENGLISH

Lifting and moving the TV

When moving or lifting the TV, read the following to prevent the TV from being scratched or damaged and for safe transportation regardless of its type and size.

• It is recommended to move the TV in the box or packing material that the TV originally came in.

• Before moving or lifting the TV, disconnect the power cord and all cables.

• When holding the TV, the screen should face away from you to avoid damage.

• Hold the top and bottom of the TV frame firmly. Make sure not to hold the transparent part, speaker, or speaker grill area.

• Use at least two people to move a large TV.

• When transporting the TV by hand, hold the TV as shown in the following illustration.

• When transporting the TV, do not expose the TV to jolts or excessive vibration.

• When transporting the TV, keep the TV upright; never turn the TV on its side or tilt towards the left or right.

• When handling the TV, be careful not to damage the protruding buttons.

• Avoid touching the screen at all times, as this may result in damage to the screen.

• Do not place the product on the floor with its front facing down without padding. Failure to do so may result in damage to the screen.

• Do not move the TV by holding the cable holders, as the cable holders may break, and injuries and damage to the TV may occur, (Depending upon model).

• When supported cable doesn’t have enough length to connect the TV set with the Companion Box (AV Box), you should use the extension cable.

• Please do not pile stuff up on or press down strongly on the speaker. This may result in product damage or degradation.

Mounting to the Wall

If you are attaching the TV to other building materials, please contact qualified personnel to install the wall mount.

• Do not apply foreign substances (oils, lubricants, etc.) to the screw parts when assembling the product. (Doing so may damage the product.)

• Do not use any unapproved items to ensure the safety and lifespan of the product.

• Any damages or injuries by using unapproved items are not covered by the warranty.

• Make sure that the screws are fastened tightly. (If they are not fastened securely enough, the TV may tilt forward after being installed.)

• Do not fasten the screws with excessive force otherwise they may strip and become loose.

Provided item


Wall mount	Punching Guide

Wall mounting screw

Wall mounting anchor

Ø5 x L65

Wall mounting screw for wood Ø3 x L18

•• Check the material of the wall and the thickness of the finishing.

•• Use the Wall mount anchor for wall material of concrete, light concrete, strong natural stone, soft natural stone masonry brick and hallow block that do not crack.

Wall Material	Tools	Wall Thickness

Concrete	Wall mounting anchor,	70 mm
	Wall mounting screw,	(2.7 inches)
Brick	Wall mounting screw,	(2.7 inches)
Brick	Drill bit (Ø 3 / 6 / 8)

Natural stone
Natural stone

Metal Panel

Plywood	Wall mounting screw,	30 mm
	Drill bit (Ø 1.8)	(1.1 inches)

EPS Panel		Penetrate the
		wall

Plasterboard +		30 mm
Plywood		(1.1 inches)

•• When installing on a gypsum board or medium-density fiberboard (MDF) wall, fasten the screws to the studs that support the wall. If there are no studs, check the distance from the inner wall before installing.

-- 30 mm (1.1 inches) or below: Install directly on the inner wall using a 65 mm (2.5 inches) screw.

-- 30 mm (1.1 inches) or above: Install using a separate hanger.

Wall

•• When installing the wall mount, check the positions of the wooden studs using a stud finder. Then, fasten the screws on at least two separate studs before proceeding.

Stud

Wall mount

•• When installing the product on wall material not designated, install the product so that each location can withstand the pull out load of 70 kg (154.3 lbs) and shear load of 100 kg (220.4 lbs) or above.

•• Use the Ø 8 mm (0.3 inches) drill bit for concrete and hammer (Impact) drill.

<![if ! IE]>

<![endif]>ENGLISH

Tools you will need

•• Phillips head + driver (manual or motorized) /

		Ø 8 mm (0.3 inches) Drill bit / Level / Stud finder / Drill
<![if ! IE]> <![endif]>ENGLISH	How to attach to masonry walls
<![if ! IE]> <![endif]>ENGLISH	Please follow the below direction.
	Please follow the below direction.
	1	Use a drill bit Ø 8 mm (0.3 inches) to drill a hole for the anchor
		location within a depth of 80 mm (3.1 inches) to 100 mm
		(3.9 inches).
	2	Clean the drilled hole.
	3	Insert the sealed wall mounting anchor to the hole. (When
		inserting the anchor, use a hammer.)
		Wall mounting
		anchor

4Set the wall mount on the wall by aligning to the location of the hole. And, set the angle adjusting part to face upward.

5Align the wall mounting screw to the hole and tighten it. Then, fasten the screws at torque of 45 kgf/cm (39.06 lbf/in) to 60 kgf/cm (52.08 lbf/in).

Wall mounting screw

• When mounting a TV on the wall, make sure not to install the TV by hanging the power and signal cables on the back of the TV.

• Do not install this product on a wall if it could be exposed to oil or oil mist. This may damage the product and cause it to fall.

• Make sure that children do not climb on or hang on the TV.

• Use a platform or cabinet that is strong and large enough to support the TV securely.

• When installing the product, first check that the wall is strong enough. Use the anchors and screws provided.

-- If you use anchors and screws that are not specified by the manufacturer, they may not hold the weight of the product, causing safety issues.

• Be sure to use the accessory cable provided. Otherwise, friction between the product and the wall may cause damage to the connector.

• When drilling holes into the wall, make sure you use a drill and drill bit with the specified diameter. Ensure that you also follow the instructions regarding the depth of the holes.

-- Otherwise, the product may be installed incorrectly and cause safety issues.

• Wear safety gloves when installing the product. Do not use your bare hands.

-- Otherwise, it may cause personal injury.

• If some parts of the wall mount do not touch the wall after it is attached, in addition to the other mounting hardware, add the double sided tape included with the accessories to stick the mount to the wall.

• If some parts of the wall mount do not touch the wall after using the wall mounting screws for wood, use the remaining screws.

• Be sure to use only the exclusive wall mounting screws provided as accessories.

• If you want to connect the TV Cable that is connected to the back panel partition, please use the enclosed Punching Guide.

Using the kensington security system (optional)

(For OLED65W8*)

The Kensington security system connector is located at the rear of the Companion Box (AV Box). For more information of installation and using, refer to the manual provided with the Kensington security system or visit http://www.kensington.com.

Connections

You can connect various external devices to the TV. For more information on external device’s connection, refer to the manual provided with each device.

Antenna/Cable

Connect an antenna, cable, or cable box to watch TV while referring to the following. The illustrations may differ from the actual items and an RF cable is optional.

•• Make sure not to bend the copper wire of the RF cable.

Copper wire

•• Complete all connections between devices, and then connect the power cord to the power outlet to prevent damage to your TV.

•• Use a signal splitter to use 2 TVs or more.

•• DTV Audio Supported Codec: MPEG, Dolby Digital

•• This TV cannot receive ULTRA HD (3840 x 2160 pixels) broadcasts directly because the related standards have not been confirmed, (Depending upon model).

Other connections

Connect your TV to external devices. For the best picture and audio quality, connect the external device and the TV with the HDMI cable.

HDMI

•• Supported HDMI Audio format: (Depending upon model)

DTS (44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz),

DTS HD (44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz), True HD (48 kHz),

Dolby Digital / Dolby Digital Plus (32 kHz, 44.1 kHz, 48 kHz), PCM (32 kHz, 44.1 kHz, 48 kHz, 96 kHz, 192 kHz)

(Only UHD models)
•	)	Picture	Additional Settings

-- On: Support 4K @ 60 Hz (4:4:4, 4:2:2, 4:2:0) -- Off: Support 4K @ 60 Hz 8 bit (4:2:0)

If the device connected to Input Port also supports ULTRA HD Deep Color, your picture may be clearer. However, if the device doesn’t support it, it may not work properly. In that case, change the TV’s setting to off.

External Devices

Supported external devices are: Blu-ray player, HD receivers, DVD players, VCRs, audio systems, USB storage devices, PC, gaming devices, and other external devices.

•• If you record a TV program on a Blu-ray/DVD recorder or VCR, make sure to connect the TV signal input cable to the TV through a DVD recorder or VCR. For more information about recording, refer to the manual provided with the connected device.

•• The external device connections shown may differ slightly from illustrations in a manual.

•• Connect external devices to the TV regardless about the order of the TV port.

<![if ! IE]>

<![endif]>ENGLISH

<![if ! IE]>

<![endif]>ENGLISH

•• If you connect a gaming device to the TV, use the cable supplied with the gaming device.

•• Refer to the external equipment’s manual for operating instructions.

•• In PC mode, there may be noise associated with the resolution, vertical pattern, contrast or brightness. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the PICTURE menu until the picture is clear. Depending upon the graphics card, some resolution settings may not allow the image to be positioned on the screen properly.

•• Some USB Hubs may not work. If a USB device connected through a USB Hub is not detected, connect it directly to the USB port on the TV.

•• The TV may be capable of operating without a set-top-box from a multichannel video programming distributor (MVPD).

•• When connecting via a wired LAN, it is recommended to use a CAT 7 cable.

Remote RS-232C setup

To obtain the RS-232C external control setup information, please visit www.lg.com. Download and read the manual, (Depending upon model).

• Do not drop the product or let it fall over when connecting external devices. Otherwise, this may result in injury or damage to the product.

• When connecting external devices such as video game consoles, make sure the connecting cables are long enough. Otherwise, the product may fall over, which may cause injury or damage the product.

Using Button

You can simply operate the TV functions, using the button.

Basic functions

Power On (Press)

Power Off 1 (Press and hold)

Volume Control

Channels Control

1 All running apps will close.

Adjusting the menu

When the TV is turned on, press thebutton one time. You can adjust the Menu items pressing or moving the buttons.

Turns the power off.

Accesses the settings menu.

Clears on-screen displays and returns to TV viewing.

Changes the input source.

Using Magic Remote

Control

(Depending upon model)

The descriptions in this manual are based on the buttons on the remote control. Please read this manual carefully and use the TV correctly.

When the message “Magic Remote battery is low. Please change the battery.” is displayed, replace the batteries.

To install batteries, open the battery cover, replace batteries (1.5 V AA) matching theandends to the label inside the compartment, and close the battery cover. Be sure to point the magic remote toward the remote control sensor on the TV. To remove the batteries, perform the installation actions in reverse. This remote uses infrared light. When in use, it should be pointed in the direction of the TV’s remote sensor.

(Some buttons and services may not be provided depending upon models or regions.)

* To use the button, press and hold for more than 3 seconds.

(POWER) Turns the TV on or off.

You can turn your set-top box on or off by adding the settop box to the universal remote control for your TV.

Number buttons Enters numbers.

(DASH) Inserts a (DASH) between numbers such as 2-1 and 2-2. Accesses the saved channels list.

(Screen Remote) Displays the Screen Remote.

-- Accesses the Universal Control Menu in some regions.

* (Screen Remote) SAP (Secondary Audio Program) Feature can be enabled by pressing the key.

* You can access apps or Live TV using the number buttons corresponding to the features.

Adjusts the volume level. (MUTE) Mutes all sounds.

* (MUTE) Accesses the Accessibility menu.

Scrolls through the saved channels.

* (Voice recognition)

Network connection is required to use the voice recognition function.

Once the voice display bar is activated on the TV screen, press and hold the button and speak your command out loud.

(HOME) Accesses the Home menu.

* (HOME) Shows the previous history. (Q. Settings) Accesses the Quick Settings.

* (Q. Settings) Displays the All Settings menu.

Wheel (OK) Press the center of the Wheel button to select a menu. You can change channels by using the wheel button.

(up/down/left/right) Press the up, down, left or right button to scroll the menu. If you pressbuttons while the pointer is in use, the pointer will disappear from the screen and Magic Remote will operate like a general remote control. To display the pointer on the screen again, shake Magic Remote to the left and right. Returns to the previous level.

* Clears on-screen displays and returns to last input viewing.

Displays the program event according to time scheduler.

1 2 Streaming Service buttons Connects to the Video Streaming Service.

(INPUT) Changes the input source.

* (INPUT) Displays a list of all the external inputs.

,	,	,	These access special functions in some menus.
Control buttons ( ,			) Controls media contents.
		By zooming in on the selected area, you can view it in

full screen.

* You can zoom in on the area where the remote control is pointed.

<![if ! IE]>

<![endif]>ENGLISH

<![if ! IE]>

<![endif]>ENGLISH

Registering Magic Remote Control

How to register the Magic Remote Control

To use the Magic Remote, first pair it with your TV.

1Put batteries into the Magic Remote and turn the TV on.

2Point the Magic Remote at your TV and press the Wheel (OK) on the remote control.

*If the TV fails to register the Magic Remote, try again after turning the TV off and back on.

How to deregister the Magic Remote Control

Press theand(HOME) buttons at the same time, for five seconds, to unpair the Magic Remote with your TV.

*Pressing and holding thebutton will let you cancel and reregister Magic Remote at the same time.

• It is recommended that an Access Point (AP) be located more than 0.2 m (0.65 ft) away from the TV. If the AP is installed closer than 0.2 m (0.65 ft), the Magic remote control may not perform as expected due to frequency interference.

• Do not mix new batteries with old batteries. This may cause the batteries to overheat and leak.

• Failure to match the correct polarities of the battery may cause the battery to burst or leak, resulting in fire, personal injury, or ambient pollution.

• This apparatus uses batteries. In your community there might be regulations that require you to dispose of these batteries properly due to environmental considerations. Please contact your local authorities for disposal or recycling information.

• Batteries inside or inside the product shall not be exposed to excessive heat such as sunshine, fire or the like.

Troubleshooting

Cannot control the TV with the remote control.

• Check if anything such as tape has been placed over the receiver. • Check if there is any obstacle between the product and the remote

control.

• Replace the batteries with new fresh ones. No image display and no sound is produced.

• Check if the product is turned on.

• Check if the power cord is connected to a wall outlet.

• Check if there is a problem in the wall outlet by connecting other products.

The TV turns off suddenly.

• Check the power control settings. The power supply may be interrupted.

• Check if the auto-off function is activated in the settings menu. • If there is no signal while the TV is on, the TV will turn off

automatically after 15 minutes of inactivity.

Abnormal Display

•• If the TV feels cold to the touch, there may be a small flicker when it is turned on. This is normal; there is nothing wrong with TV. Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the TV’s performance. Avoid touching the screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen.

•• This panel is an advanced product that contains millions of pixels. In a very few cases, you could see fine dots on the screen while you’re viewing the TV. Those dots are deactivated pixels and do not affect the performance and reliability of the TV.

•• A blue light blinks on the front of the Companion Box (AV Box). -- The TV may have a problem with the cooling fan or the

temperature in the TV may be too high. Contact an authorized service center.

•• A magenta light blinks on the front of the Companion Box (AV Box). -- The TV may have a problem in the moving speaker. Contact an

authorized service center.

•• An orange light blinks on the front of the Companion Box (AV Box). -- The cable from panel may not be properly connected to the

Companion Box (AV Box). Unplug the power cord and reconnect the cable from the panel. Then plug the power cord in and press the power button. If it still doesn’t work after the steps above, contact an authorized service center.

Generated Sound

• Cracking noise A cracking noise that occurs when watching or turning off the TV is generated by plastic thermal contraction due to temperature and humidity. This noise is common for products where thermal deformation is required.

•• Electrical circuit humming/panel buzzing A low level noise is generated from a high-speed switching circuit, which supplies a large amount of current to operate a product. It varies depending upon the product. This generated sound does not affect the performance and reliability of the product.

• Make sure to wring any excess water or cleaner from the cloth.

• Do not spray water or cleaner directly onto the TV screen. • Make sure to spray just enough of water or cleaner onto a

dry cloth to wipe the screen.

• To clean the top of the Companion Box (AV box), spray a soft cloth with water. Then, wipe the surface so that the product does not come in direct contact with water. Next, wipe it again so that no moisture remains.

<![if ! IE]>

<![endif]>ENGLISH

<![if ! IE]>

<![endif]>ENGLISH

Specifications

Product specifications may be changed without prior notice due to upgrade of product functions.

Estimated yearly energy consumption indicated on the FTC label is measured in accordance with the Test Procedures for Television Sets (USA only). The actual energy consumption depends on the usage environment (The content watched, TV settings, etc.).

		Broadcasting Specifications
Television system			ATSC, NTSC-M, 64 & 256 QAM

Program coverage		VHF 2-13, UHF 14-69, DTV 2-69, CATV 1-135, CADTV 1-135

External antenna impedance			75 Ω


	Wireless module (LGSBWAC72) Specifications
	Wireless LAN (IEEE 802.11a/b/g/n/ac)

Frequency Range			Output Power (Max.)

2400 to 2483.5 MHz			15 dBm
5150 to 5725 MHz			14.5 dBm
5725 to 5850 MHz			14.5 dBm

		Bluetooth

Frequency Range			Output Power (Max.)

2400 to 2483.5 MHz			8.5 dBm

As band channels can vary per country, the user cannot change or adjust the operating frequency. This product is configured for the regional frequency table.

For consideration of the user, this device should be installed and operated with a minimum distance of 20 cm (7.8 inches) between the device and the body.

FCC ID: BEJLGSBWAC72 / IC: 2703H-LGSBWAC72

	Environment condition
Operating Temperature		0 °C to 40 °C (32 °F to 104 °F)

Operating Humidity		Less than 80 %

Storage Temperature		-20 °C to 60 °C (-4 °F to 140 °F)

Storage Humidity		Less than 85 %

Open Source Software

Notice Information

To obtain the source code under GPL, LGPL, MPL, and other open source licenses, that is contained in this product, please visit http://opensource. lge.com.

In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download.

LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping, and handling) upon email request to opensource@lge.com.

This offer is valid for a period of three years after our last shipment of this product. This offer is valid to anyone in receipt of this information.

Licenses

Supported licenses may differ by model.

<![if ! IE]>

<![endif]>ENGLISH

<![if ! IE]>

<![endif]>ENGLISH

Important Information for Preventing Image Retention

OLED is a self-emissive technology, which brings many significant benefits to image quality and performance. As with any self-emitting display, it is possible for users of OLED TVs to experience temporary image retention under certain conditions, such as when displaying a static image on the screen for a long time. Even so, this phenomenon is rare under ordinary viewing conditions and is not a malfunction. Below sets forth helpful information you may refer to for using your OLED TV.

Examples of Images that may Cause Image Retention

• Still images or fixed images containing certain information that are displayed uninterrupted on the screen, such as channel numbers, station logos, program titles, news or movie subtitles, and headlines.

• Fixed menu or icons for video game consoles or broadcasting set-top boxes.

• Black bars shown on the left, right, top, or bottom of the screen, such as in images with a 4:3 or 21:9 ratio.

Recommended Measures for Preventing Image Retention

• Avoid watching a video displaying an image as listed above for extended periods of time.

• Adjust your TV settings as below when turning on a video exhibiting an image as listed above for extended periods of time.

-- PicturePicture Mode SettingsPicture ModeAPS -- PicturePicture Mode SettingsOLED LIGHTAdjust

to lower value

-- PictureOLED Panel SettingsLogo Luminance

AdjustmentHigh

• Turn off the menu bar of an external device, such as a set-top box, to prevent long-term display of the menu bar of such device. (Please refer to the manual of the applicable external device for instructions.)

• Adjust the settings as below when watching a video constantly showing black bars on the left, right, top or bottom, in order to remove the black bars.

-- PictureAspect Ratio SettingsAspect Ratio Vertical Zoom or All-Direction Zoom

Information on Functions Supporting Image Quality in Relation to Temporary Image Retention

• OLED TV offers a function called Pixel Refresher, which helps to prevent temporary image retention. This function can be operated automatically or manually.

• The auto feature will activate when the TV power is turned off, but only after the TV has been turned on for a cumulated total of four

(4) hours or more, which need not be consecutive. Pixel Refresher will automatically run for several minutes after the screen is turned off. (Please note that failure to supply the AC power or disconnecting the power cord from the outlet will disable the auto feature.)

• To manually activate Pixel Refresher, you will have to select

PictureOLED Panel SettingsPixel Refresher in the settings. Once manually activated, the function will run for approximately one (1) hour. During this time, a horizontal line may appear on the screen; however, this is not a malfunction.

• If Pixel Refresher has not been manually activated for a certain period of time, a pop-up window advising to activate this function will appear on the screen. Please follow the instructions set forth in the pop-up window.

• In addition to Pixel Refresher, there are other functions available for protecting the screen from image retention. For example, a function that automatically reduces the screen brightness level, in part or in whole, will be activated when a static image is displayed uninterrupted on the screen. Once the static image disappears, the brightness level will automatically return to the previous level. This function is an intended function, and not a malfunction.

Regulatory

FCC NOTICE

(For USA)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used

in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and the receiver.

-- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC Radio Frequency Interference Requirements (for UNII devices)

High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and/or damage this device. This device cannot be co-located with any other transmitter.

FCC RF Radiation Exposure Statement

[For having wireless function (WLAN, Bluetooth,...)]

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be colocated or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 20 cm (7.8 inches) between the radiator and your body. Users must follow the specific operating instructions for satisfying RF exposure compliance.

Industry Canada Statement

(For Canada)

[For having wireless function (WLAN, Bluetooth,...)]

This device complies with Industry Canada’s applicable licence-exempt RSSs. Operation is subject to the following two conditions:

(1)This device may not cause interference; and

(2)This device must accept any interference, including interference that may cause undesired operation of the device.

IC Radiation Exposure Statement

(For Canada)

[For having wireless function (WLAN, Bluetooth,...)]

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm (7.8 inches) between the antenna & your body.

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

<![if ! IE]>

<![endif]>ENGLISH

<![if ! IE]>

<![endif]>ENGLISH

RSS-247 Requirement

(For Canada)

[For product having the wireless function using 5 GHz frequency bands]

•• The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

•• For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;

•• For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits as appropriate; and

•• [For devices operating in the band 5250-5350 MHz having an e.i.r.p. greater than 200 mW] antenna type(s), antenna models(s), and worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 of RSS-247 shall be clearly indicated.

Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.

NOTE TO CABLE/TV INSTALLER

(For USA and Canada)

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that

the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.

WARNING!

Never place a television set in an unstable location. A television set may fall, causing serious personal injury or death. Many injuries, particularly to children, can be avoided by taking simple precautions such as:

•• Using cabinets or stands recommended by the manufacturer of the television set.

•• Only using furniture that can safely support the television set.

•• Ensuring the television set is not overhanging the edge of the supporting furniture.

•• Not placing the television set on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and the television set to a suitable support.

•• Not placing the television set on cloth or other materials that may be located between the television set and supporting furniture.

•• Educating children about the dangers of climbing on furniture to reach the television set or its controls.

If your existing television set is being retained and relocated, the same considerations as above should be applied.

Symbols

Refers to alternating current (AC).

Refers to direct current (DC).

Refers to class II equipment.

Refers to stand-by.

Refers to “ON” (power).

Refers to dangerous voltage.

<![if ! IE]>

<![endif]>ENGLISH

Declaration of Conformity

Trade Name	LG
Responsible Party	LG Electronics Inc.
Address	1000 Sylvan Ave. Englewood
	Cliffs NJ 07632 U.S.A
TEL	201-266-2534

LG Customer Information Center

For inquires or comments, visit www.lg.com or call;

1-888-542-2623 CANADA

1-800-984-6306 USA

The model and serial numbers of the TV are located on the back and on one side of the TV. Record them below should you ever need service.

MODEL

SERIAL NO.

OWNER’S MANUAL

EXTERNAL CONTROL DEVICE SETUP

Please read this manual carefully before operating the set and retain it for future reference.

www.lg.com

<![if ! IE]>

<![endif]>ENGLISH

2 KEY CODES

KEY CODES

• This feature is not available for all models.

Code	Function	Note	Code	Function	Note
(Hexa)	Function	Note	(Hexa)	Function	Note
(Hexa)			(Hexa)

00	CH +, PR +	R/C Button	53	List	R/C Button

01	CH -, PR -	R/C Button	5B	Exit	R/C Button

02	Volume +	R/C Button	60	PIP(AD)	R/C Button

03	Volume -	R/C Button	61	Blue	R/C Button

06	> (Arrow Key / Right Key)	R/C Button	63	Yellow	R/C Button

07	< (Arrow Key / Left Key)	R/C Button	71	Green	R/C Button

08	Power	R/C Button	72	Red	R/C Button

09	Mute	R/C Button	79	Ratio / Aspect Ratio	R/C Button

0B	Input	R/C Button	91	AD (Audio Description)	R/C Button

0E	SLEEP	R/C Button	9E	LIVE MENU	R/C Button

0F	TV, TV/RAD	R/C Button	7A	User Guide	R/C Button

10 - 19	* Number Key 0 - 9	R/C Button	7C	Smart / Home	R/C Button

1A	Q.View / Flashback	R/C Button	7E	SIMPLINK	R/C Button

1E	FAV (Favorite Channel)	R/C Button	8E	►► (Forward)	R/C Button

20	Text (Teletext)	R/C Button	8F	◄◄ (Rewind)	R/C Button

21	T. Opt (Teletext Option)	R/C Button	AA	Info	R/C Button

28	Return (BACK)	R/C Button	AB	Program Guide	R/C Button

30	AV (Audio / Video) Mode	R/C Button	B0	► (Play)	R/C Button

39	Caption/Subtitle	R/C Button	B1	(Stop / File List)	R/C Button

40	Λ (Arrow Key / Cursor Up)	R/C Button	B5	RECENT	R/C Button

41	V (Arrow Key / Cursor	R/C Button	BA	(Freeze / Slow Play /	R/C Button
	Down)			Pause)
42	My Apps	R/C Button	BB	Soccer	R/C Button

43	Menu / Settings	R/C Button	BD	(REC)	R/C Button

44	OK / Enter	R/C Button	DC	3D	R/C Button

45	Q.Menu	R/C Button	99	AutoConfig	R/C Button

4C	List, - (ATSC Only)	R/C Button	9F	App / *	R/C Button

4D	PICTURE	R/C Button	9B	TV / PC	R/C Button

52	SOUND	R/C Button

*Key code 4C (0x4C) is available on ATSC/ISDB models which use major/minor channel. (For South Korea, Japan, North America, Latin America except Colombia models)

EXTERNAL CONTROL DEVICE SETUP 3

EXTERNAL CONTROL DEVICE SETUP

• Image shown may differ from your TV.

Connect the USB to Serial converter/RS-232C input jack to an external control device (such as a computer or an A/V control system) to control the product’s functions externally.

Note: The type of control port on the TV can be different between model series.

*Please be advised that not all models support this type of connectivity.

*Cable is not provided.

USB to Serial converter with USB Cable

USB Type

(PC)

<![if ! IE]>

<![endif]>USB IN

(TV)

•LGTV supports PL2303 chip-based (Vendor ID : 0x0557, Product ID : 0x2008) USB to serial converter which is not made nor provided by LG.

•It can be purchased from computer stores that carry accessories for IT support professionals.

RS-232C With RS232C Cable

DE9 (D-Sub 9pin) Type

•You need to purchase the RS-232C (DE9, D-Sub 9pin female-to-female type) to RS-232C cable required for the connection between the PC and the TV, which is specified in the manual.

	RS-232C IN
(PC)	(CONTROL & SERVICE)	(TV)

The connection interface may differ from your TV.

<![if ! IE]>

<![endif]>ENGLISH

+ 52 hidden pages