Indesit K6G32-G User Manual
Cooker with electric
ventilated oven
Instructions for installation and use
K6G32/G
Cooker with electric ventilated oven
Instructions for installation and use
Important safety warnings
To maintain the EFFICIENCY and SAFETY of this appliance, we recommend:
• call only the Service Centers authorized by the manufacturer
• always use original Spare Parts
1 These instructions are only for those countries whose
symbols appear in the booklet and on the matriculation
plate of the appliance.
2 This appliance is intended for non-professional use
within the home.
3 Before using the appliance, read the instructions in this
owner’ s manual carefully since y ou should find all the
instruction you require to ensure safe installation, use
and maintenance. Always keep this owner’s manual
close to hand since you may need to refer to it in the
future.
4 When you have removed the packing, check that the
appliance is not damaged. If you have any doubts, do not
use the appliance, contact your nearest Ariston Service
Centre. Nev er leav e the packing components (plastic bags,
foamed polystyrene, nails , etc.) within the reach of children
since they are a source of potential danger .
5 The appliance must be installed only by a qualified person in
compliance with the instructions provided. The manufacturer
declines all responsibility for improper installation which may
harm persons and animals and damage property .
6 The electrical safety of this appliance can only be guaranteed
if the cooker is correctly and efficiently earthed, in compliance
with current regulations on electrical safety. Alw ays ensure
that the earthing is efficient; if you hav e any doubts call in a
qualified electrician to check the system. The manufacturer
declines all responsibility for damage resulting from a system
which has not been earthed.
7 Before plugging the appliance into the mains, chec k that the
specifications indicated on the date plate correspond to those
of the electrical and gas mains system of your home.
8 Check that the electrical capacity of the system and sockets
will support the maximum power of the hob, as indicated on
the data plate. If you have any doubts, call in a qualified
technician.
9 An omnipolar switch with a contact opening of at least 3 mm
or more, is required for the installation.
10 If the socket and hob plug are not compatib le, have the socke t
replaced with a suitable model by a qualified technician who
should also check that the cross-section of the socket cab le
is suited to the power absorbed by the appliance . The use of
adaptors, multiple sockets and/or extensions, is not
recommended. If their use can not be a voided, remember to
use only single or multiple adapters and extensions which
comply with current safety regulations. In these cases, nev er
exceed the maximum current capacity indicated on the single
adaptor or extension and the maximum po wer indicated on
the multiple adapter .
11 Do not leave the appliance plugged in if it is not in use . Switch
off the main switch and gas supply when you are not using
the cooker.
12 The openings and slots used for ventilation and dispersion
of heat on the rear and below the control panel must ne ver
be covered.
13 The user must not replace the supply cable of this appliance.
Always call an after-sales servicing centre authorised by the
manufacturer in the case of cable damage or replacement.
14 This appliance must be used for the purpose for which it was
expressly designed. Any other use (e.g. heating rooms) is
considered to be improper and consequently dangerous. The
manufacturer declines all responsibility f or damage resulting
from improper and irresponsible use.
15 A number of fundamental rules must be follow ed when using
electrical appliances. The following are of particular
importance:
· do not touch the appliance when your hands or feet are
wet
· do not use the appliance barefooted
· never allow the Mains Cable to be stretched, pulled or
damaged if the Cooker is mov ed for cleaning etc. Do not
use the cooker if the Mains Cable is damaged, consult a
qualified electrician.
· do not allow the cooker to be used unsupervised by
children or persons unfamiliar with it.
16 Always s witch off the electrical supply to the cooker and allow
it to cool down before carrying out any cleaning operations
etc.
17 If you are no longer using an appliance of this type , remember
to make it unserviceable by unplugging the appliance from
the mains and cutting the supply cable. Also make all
potentially dangerous parts of the appliance, safe, abov e all
for children who could play with the appliance .
18 T o avoid accidental spillage do not use cookw are with uneven
or deformed bottoms on the burners or on the electric plates.
19 Special care should be taken when using chip pans etc. in
order to avoid splashing or spillage of hot oil. The y should not
be used unattended since overheated oil may boil o ver and
could also ignite.
20 Par ts of this appliance, cooking surfaces, retain heat for
considerable periods after switching off. Care should,
therefore, be taken when touching these areas bef ore they
have completely cooled down.
21 Never use flammable liquids such as alcohol or gasoline,
etc. near the appliance when it is in use.
22 When using small electric appliances near the hob, keep the
supply cord awa y from the hot parts.
23 Make sure the knobs are in the “•”/”¡” position when the
appliance is not in use.
24 When the appliance is in use, the heating elements and
some parts of the oven door become extremely hot.
Make sure you don't touch them and keep children well
away.
25 Gas units need a regular air replacement for a correct
functioning. Make sure that the requirements requested
in the “Positioning” paragraph are all observed in the
owner’ s manual.
26 If the cooker is placed on a pedestal, take the necessary
precautions to prevent the same from sliding off the pedestal
itself.
27 Warning: ne ver place hot containers or items and flamma-
ble materials inside the dishwarmer drawer .
28 This owner’ s manual is for a c lass 1 appliance (installed
independently) or class 2, subclass 1 appliances (installed between two cabinets).
3
Installation
HOOD
420
Min.
min.
650
mm. with hood
min.
700
mm. without hood
mm.
600
Min. mm.
420
Min. mm.
The following instructions should be read by a qualified
technician to ensure that the appliance is installed,
regulated and technically serviced correctly in compliance
with current regulations.
Important: remember to unplug the appliance from
the mains before regulating the appliance or carrying
out any maintenance work.
Positioning
Important: this unit may be installed and used only in
permanently ventilated rooms according to the British
Standards Codes Of Practice: B.S. 6172/B.S. 5440, Par. 2
and B.S. 6891 Current Editions . The following requirements
must be observed:
a) The cooker should not be installed in a bed sitting room
3
with a volume of less than 20m
of volume less than 5m
2
110cm
between 5m
is required, if it is installed in a room of volume
3
and 10m3 a supplementary airvent area of
3
50cm2 is required, if the volume exceeds 11m
. If it is installed in a room
an air vent of effective area of
3
no airvent
is required. How ev er, if the room has a door or a windo w
which opens directly to the outside no air vent is required
3
even when the v olume is between 5m
and 11m3.
b) During prolonged use of the appliance you may consider
it necessary to open a window to the outside to improve
ventilation.
c) If there are other fuel burning appliances in the same
room, B.S.5440 Part 2 Current Edition, should, be
consulted to determine the requisite air vent requirements.
Levelling Y our Appliance (only on certain models)
4 support feet which are adjusted using screws are located
in the lower part of the cooker. These level off the oven
when necessary. It is essential that the cook er be standing
level.
Installation of the cooker
The cooker is prepared with protection degree against
excessive heating of type X, the appliance can therefore
be installed next to cabinets, pro vided the height does not
exceed that of the hob. If the cooker is placed touching
walls or sides of neighbouring cabinets, these must be
capable of withstanding a temperature rise of 50°C above
room temperature. For a correct installation of the cook er
the following precautions m ust be f ollo wed:
a) The cooker may be located in a kitchen, a kitonen/
diner or bed sitting room, but not in a bathroom or
shower room.
b) The fur niture units next to the cooker, that is higher
than the working boards, must be placed at least
600mm from the edge of the board. Curtains must not
be fitted immediately behind the cooker or within
600mm of the sides of the cooker.
c) The hoods must be installed according to the
requirements in the hood handbook.
d) Wall cabinets may be fitted in line with the sides of the
base units, providing that the lower edge of the wall
cabinet is a minimum of 420 mm. above the worktop.
The minimum distance combustible material kitchen
units can be fitted directly above the worktop is 700
mm (Fig. A).
e) The wall in contact with the back of the cooker must
be of flameproof material.
f) The cooker is fitted with a safety chain that must be
attached to a hook, secured to the wall behind the
appliance.
Note: some models can have their gas connection
inverted. It is important to make sure the safety chain
is always situated on the side which corresponds to
the hose holder (Fig. B).
Mounting the legs (only on certain models)
Press-fit legs are supplied which fit under the base of your
cooker.
Fig. A Fig. B
Gas connection
The cooker should be connected to the gas-supply by a
corgi registered installer . During installation of this product
it is essential to fit an approved gas tap to isolate the supply
from the appliance for the convenience of an y subsequent
removal or servicing. Connection of the appliance to the
gas mains or liquid gas must be carried out according to
the prescribed regulation in force, and only after it is
ascertained that it is adaptable to the type of gas to be
used. If not, follow the instructions indicated in the
paragraph headed “Adaptation to diff erent gas types”. On
some models the gas supply can be connected on the left
or on the right, as necessary; to change the connection,
reverse the position of the hose holder with that of the cap
and replace the gasket (supplied with the appliance). In
the case of connection to liquid gas, by tank, use pressure
4
regulators that conform to the regulation in force. The gas
GREEN &
YELLOW
BROWN
BLUE
13 amp fuse
CROSS-BAR
CORD GRIP
supply must be connected to the left of the appliance. Be
sure that the hose does not pass through the rear of the
cooker touching hot parts.
HOT PARTS
Important: make sure the supply pressure conforms with
the values shown in the table entitled “Car acteristics of the
burners and nozzles”. When the cooker is installed
between cabinets (recessed), the gas connection must
be effected by an approved flexible hose with bayonet
fitting (BS 669 Current Edition). The gas inlet for the
cookers is a threaded G 1/2 gas female fitting.
Connecting the gas supply
To make the connection, a flexible hose should be used
corresponding to the current gas regulations which are:
• the hose must nev er be at any point in its lenght in contact
with the “hot” parts of the cooker;
• the hose must nev er be longer than 1,5 metre;
• the hose must not be subject to any tension or torsional
stress and it must not have any e xcessively narrow curves
or bottlenecks;
• the hose must be easy to inspect along its entire length
to check its condition;
• the hose must alwa ys be in good condition, never attempt
to repair.
Important: the installation must comply with gas safety
(installation and use) regulations 1984. In all cases for the
above, by low , a qualified, corgi approv ed engineer must be
called for installation.
Electrial connection
Pow er supply voltage and frequency: 230-240V a.c. 50/60 Hz.
Note: the supply cable must be positioned so that it never
reaches at any point a temperature 50°C higher than the
room temperature. The cable must be routed awa y from the
rear vents. Should you require it, you may use a longer cab le,
however, you must ensure that the cable supplied with the
appliance is replaced by one of the same specifications in
accordance with current standards and legislation.
Y our appliance is supplied with a 13 amp fused plug that can
be plugged into a 13 amp socket f or immediate use. Before
using the appliance please read the instructions below.
WARNING - THIS APPLIANCE MUST BE EARTHED.
THE FOLLOWING OPERA TIONS SHOULD BE CARRIED
OUT BY A QUALIFIED ELECTRICIAN.
Replacement fuse covers:
If a replacement fuse cover is fitted, it must be of the correct
colour as indicated by the coloured marking or the colour
that is embossed in words on the base of the plug.
Replacements can be obtained directly from your nearest
Service Depot.
Removing the plug:
If your appliance has a non-rewireable moulded plug and
you should wish to remove it to add a cable extension or to
re-route the mains cable through partitions, units etc., please
ensure that either:
• the plug is replaced by a fused 13 amp re-wireable plug
bearing the BSI mark of approval.
or:
• the mains cable is wired directly into a 13 amp cable outlet,
controlled by a switch, (in compliance with BS 5733) which
is accessible without moving the appliance.
Please note: for appliances with a rating greater than 13
amp (eg: electric hob, doub le ovens and freestanding electric
cookers etc.) the mains cable must be wired into a cooker
output point with a rating of 45 amp. In this case the cab le is
not supplied.
Disposing of the plug:
Ensure that before disposing of the plug itself, you mak e the
pins unusable so that it cannot be accidentally inserted into
a socket. Instructions for connecting cable to an alternative
plug:
Important: the wires in the mains lead are coloured in
accordance with the following code:
Green & Yellow - Earth
Blue - Neutral
Brown - Live
If the colours of the wires in the mains lead do not correspond
with the coloured markings identifying the terminals in your
plug, proceed as follows:
Connect Green & Yellow wire to terminal marked “E” or
or coloured Green or Green & Yellow .
Connect Brown wire to terminal marked “L” or coloured Red.
Connect Blue wire to terminal marked “N” or coloured Black.
If a 13 amp plug (BS 1363) is used it must be fitted with a 13
amp fuse. A 15 amp plug must be protected by a 15 amp
fuse, either in the plug or adaptor or at the distribution board.
If you are in any doubt about the electrical supply to your
machine, consult a qualified electrician before use.
How to connect an alternative plug:
The wires in this mains lead are coloured in accordance with
the following code:
BLUE “NEUTRAL” (“N”)
BRO WN “LIVE” (“L”)
GREEN AND YELLO W “EARTH” (“E”)
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA approved fuse
to BS 1362 should always be used, and the fuse cover refitted. If the fuse cov er is lost, the plug must not be used until
a replacement is obtained.
5
Loading...