HP HCPL-263A, HCPL-263N, HCPL-261N, HCPL-261A, HCPL-063N Datasheet

H

HCMOS Compatible, High CMR,

10 MBd Optocouplers

Technical Data

Features

•HCMOS/LSTTL/TTL Performance Compatible

•1000 V/μs Minimum Common Mode Rejection

(CMR) at VCM = 50 V (HCPL261A Family) and 15 kV/μs

Minimum CMR at VCM = 1000 V (HCPL-261N Family)

•High Speed: 10 MBd Typical

•AC and DC Performance

Specified over Industrial Temperature Range -40°C to +85°C

•Available in 8 Pin DIP, SOIC-8 Packages

•Safety Approval

UL Recognized per UL1577 2500 V rms for 1 minute and 5000 V rms for 1 minute (Option 020)

CSA Approved

VDE 0884 Approved with

VIORM = 630 V peak for

HCPL-261A/261N

Option 060

Applications

HCPL-261A HCPL-061A HCPL-263A HCPL-063A HCPL-261N HCPL-061N HCPL-263N HCPL-063N

•Computer-Peripheral Interface

•Digital Isolation for A/D, D/A Conversion

•Switching Power Supplies

•Instrumentation Input/Output Isolation

•Ground Loop Elimination

•Pulse Transformer Replacement

Description

The HCPL-261A family of optically coupled gates shown on this data sheet provide all the benefits of the industry standard 6N137 family with the added benefit of HCMOS

compatible input current. This allows direct interface to all common circuit topologies without additional LED buffer or drive components. The AlGaAs LED used allows lower drive currents and reduces degradation by using the latest LED technology. On the single channel parts, an enable output allows the detector to be strobed. The output of the detector IC is an open collector schottkyclamped transistor. The internal shield provides a minimum common mode transient immunity of 1000 V/μs for the HCPL-261A family and 15000 V/μs for the HCPL-261N family.

Functional Diagram

		HCPL-261A/261N
		HCPL-061A/061N
NC	1	8	VCC
ANODE	2	7	VE
CATHODE	3	6	VO
NC	4	5	GND
		SHIELD

ANODE 1

CATHODE 1

CATHODE 2

ANODE 2

	HCPL-263A/263N
	HCPL-063A/063N
1	8	VCC
2	7	VO1
3	6	VO2
4	5	GND
	SHIELD

•Low Input Current (3.0 mA) HCMOS Compatible Version of 6N137 Optocoupler

•Isolated Line Receiver

•Simplex/Multiplex Data Transmission

TRUTH TABLE (POSITIVE LOGIC)

LED	ENABLE	OUTPUT
ON	H	L
OFF	H	H
ON	L	H
OFF	L	H
ON	NC	L
OFF	NC	H

TRUTH TABLE (POSITIVE LOGIC)

LED	OUTPUT
ON	L
OFF	H

The connection of a 0.1 μF bypass capacitor between pins 5 and 8 is required.

CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD.

1-166

5965-3593E

Selection Guide

									Widebody
Minimum CMR			Input		8-Pin DIP (300 Mil)		Small-Outline SO-8		(400 Mil)	Hermetic
			On-		Single	Dual	Single	Dual	Single	Single and
dV/dt	VCM		Current	Output	Channel	Channel	Channel	Channel	Channel	Dual Channel
(V/μs)	(V)		(mA)	Enable	Package	Package	Package	Package	Package	Packages
NA	NA		5	YES	6N137[1]		HCPL-0600[1]		HCNW137[1]
				NO		HCPL-2630[1]		HCPL-0630[1]
5,000	50			YES	HCPL-2601[1]		HCPL-0601[1]		HCNW2601[1]
				NO		HCPL-2631[1]		HCPL-0631[1]
10,000	1,000			YES	HCPL-2611[1]		HCPL-0611[1]		HCNW2611[1]
				NO		HCPL-4661[1]		HCPL-0661[1]
1,000	50			YES	HCPL-2602[1]
3,500	300			YES	HCPL-2612[1]
1,000	50		3	YES	HCPL-261A		HCPL-061A
				NO		HCPL-263A		HCPL-063A
1,000[2]	1,000			YES	HCPL-261N		HCPL-061N
				NO		HCPL-263N		HCPL-063N
1,000	50		12.5	[3]						HCPL-193X[1]
										HCPL-56XX[1]
										HCPL-66XX[1]

Notes:

1.Technical data are on separate HP publications.

2.15 kV/μs with VCM = 1 kV can be achieved using HP application circuit.

3.Enable is available for single channel products only, except for HCPL-193X devices.

Ordering Information

Specify Part Number followed by Option Number (if desired).

Example:

HCPL-261A#XXX

020 = 5000 V rms/1 minute UL Rating Option*

060 = VDE 0884 VIORM = 630 Vpeak Option** 300 = Gull Wing Surface Mount Option***

500 = Tape and Reel Packaging Option

Option data sheets available. Contact your Hewlett-Packard sales representative or authorized distributor for information.

*For HCPL-261A/261N/263A/263N (8-pin DIP products) only.
**For HCPL-261A/261N only. Combination of Option 020 and Option 060 is not available.
***Gull wing surface mount option applies to through hole parts only.					HCPL-263A/263N
					HCPL-063A/063N
Schematic						ICC		8
								VCC
	HCPL-261A/261N			1	IF1	IO1
	HCPL-061A/061N			+				VO1
IF		ICC	VCC	VF1				7
2+		8
		IO	VO	–
		6		2
					SHIELD
VF				3	IF2	IO2
				–				VO2
–
3		5	GND					6
	SHIELD			VF2
	IE	7
	VE			+
USE OF A 0.1 µF BYPASS CAPACITOR CONNECTED				4				GND
					SHIELD
BETWEEN PINS 5 AND 8 IS RECOMMENDED (SEE NOTE 16).								5
							1-167

OPTOCOUPLERS

HCPL-261A/261N/263A/263N Outline Drawing

Pin Location (for reference only)

		9.40 (0.370)
								9.90 (0.390)
		8						7	6					5			OPTION CODE*
TYPE NUMBER																											0.20 (0.008)
																												0.33 (0.013)
				HP				XXXXZ									DATE CODE			6.10 (0.240)
																				6.60 (0.260)
								YYWW										7.36 (0.290)										5°	TYP.
PIN ONE																		7.88 (0.310)
			1					2	3					4
															1.78 (0.070) MAX.
									1.19 (0.047) MAX.

	4.70	(0.185) MAX.
	0.51 (0.020) MIN.
	2.92 (0.115)	MIN.
0.76 (0.030)	0.65 (0.025) MAX.
1.40 (0.056)	2.28 (0.090)
	2.80 (0.110)

DIMENSIONS IN MILLIMETERS AND (INCHES).

* MARKING CODE LETTER FOR OPTION NUMBERS. "L" = OPTION 020

"V" = OPTION 060

OPTION NUMBERS 300 AND 500 NOT MARKED.

Figure 1. 8-Pin Dual In-Line Package Device Outline Drawing.

																																							PIN LOCATION (FOR REFERENCE ONLY)
										9.65 ± 0.25																																		1.02 (0.040)
							(0.380 ± 0.010)																																										1.19 (0.047)
						8					7								6					5
																																																												4.83 TYP.
																																																											(0.190)
																												6.350 ± 0.25
																												(0.250 ± 0.010)																															9.65 ± 0.25
																																																											(0.380 ± 0.010)
					1		2										3						4
																																																																			0.38 (0.015)
																																1.19 (0.05)																																			0.64 (0.025)
																																												1.78 (0.07)
																										1.780																				9.65 ± 0.25
																																									(0.380 ± 0.010)
1.19																							(0.070)
																												MAX.																		7.62 ± 0.25
(0.047)
																																												(0.300 ± 0.010)
MAX.
																																																												0.20 (0.008)
																												4.19				MAX.
																																																														0.33 (0.013)
1.080 ± 0.320																							(0.165)
																																											0.635 ± 0.25
(0.043 ± 0.013)																																														(0.025 ± 0.010)
							2.540																									0.635 ± 0.130																																12° NOM.
																																(0.025 ± 0.005)
(0.100)
								BSC
DIMENSIONS IN MILLIMETERS (INCHES).
TOLERANCES (UNLESS OTHERWISE SPECIFIED): xx.xx = 0.01
LEAD COPLANARITY																																			xx.xxx = 0.005
MAXIMUM: 0.102 (0.004)

Figure 2. Gull Wing Surface Mount Option #300.

1-168

HCPL-061A/061N/063A/063N Outline Drawing

8

7

6

5

5.842 ± 0.203

XXX

(0.236 ± 0.008)

3.937 ± 0.127

YWW

(0.155 ± 0.005)

TYPE NUMBER (LAST 3 DIGITS)

DATE CODE

PIN

1

2

3

4

0.381 ± 0.076

ONE

1.270

BSG

(0.016 ± 0.003)

(0.050)

5.080 ± 0.005

7°

45° X 0.432

(0.017)

(0.200 ± 0.005)

3.175 ± 0.127

(0.125 ± 0.005)

1.524

(0.060)

0.152 ± 0.051

(0.006 ± 0.002)

	0.305
DIMENSIONS IN MILLIMETERS AND (INCHES).				(0.012)MIN.

LEAD COPLANARITY = 0.10 mm (0.004 INCHES).

0.228 ± 0.025

(0.009 ± 0.001)

Figure 3. 8-Pin Small Outline Package Device Drawing.

Solder Reflow Temperature Profile (HCPL-06XX and Gull Wing Surface Mount Option 300 Parts)

	260
	240
	220																																																																				T = 145°C, 1°C/SEC
°C	200								T = 115°C, 0.3°C/SEC
	180
–	160
TEMPERATURE
	60
	140
	120
	100
	80
	40																		T = 100°C, 1.5°C/SEC
	20
	0
	0			1							2								3							4									5									6			7							8							9							10							11							12

TIME – MINUTES

Note: Use of Nonchlorine Activated Fluxes is Recommended.

Regulatory Information

The HCPL-261A and HCPL-261N families have been approved by the following organizations:

UL

Recognized under UL 1577, Component Recognition Program, File E55361.

CSA

Approved under CSA Component Acceptance Notice #5, File CA 88324.

VDE

Approved according to VDE 0884/06.92. (HCPL-261A/261N Option 060 only)

OPTOCOUPLERS

1-169

Insulation and Safety Related Specifications

		8-Pin DIP
		(300 Mil)	SO-8
Parameter	Symbol	Value	Value	Units	Conditions
Minimum External Air	L(101)	7.1	4.9	mm	Measured from input terminals to
Gap (External					output terminals, shortest distance
Clearance)					through air.
Minimum External	L(102)	7.4	4.8	mm	Measured from input terminals to
Tracking (External					output terminals, shortest distance
Creepage)					path along body.
Minimum Internal Plastic		0.08	0.08	mm	Through insulation distance, conductor
Gap (Internal Clearance)					to conductor, usually the direct
					distance between the photoemitter and
					photodetector inside the optocoupler
					cavity.
Tracking Resistance	CTI	200	200	Volts	DIN IEC 112/ VDE 0303 Part 1
(Comparative Tracking
Index)
Isolation Group		IIIa	IIIa		Material Group (DIN VDE 0110, 1/89,
					Table 1)

Option 300 – surface mount classification is Class A in accordance with CECC 00802.

VDE 0884 Insulation Related Characteristics

(HCPL-261A/261N Option 060 ONLY)

Description	Symbol		Characteristic	Units
Installation classification per DIN VDE 0110/1.89, Table 1
for rated mains voltage £ 300 V rms			I-IV
for rated mains voltage £ 450 V rms			I-III
Climatic Classification			55/85/21
Pollution Degree (DIN VDE 0110/1.89)			2
Maximum Working Insulation Voltage	VIORM		630	Vpeak
Input to Output Test Voltage, Method b*
VIORM x 1.875 = VPR, 100% Production Test with tm = 1 sec,	VPR		1181	Vpeak
Partial Discharge < 5 pC
Input to Output Test Voltage, Method a*
VIORM x 1.5 = VPR, Type and sample test, tm = 60 sec,	VPR		945	Vpeak
Partial Discharge < 5 pC
Highest Allowable Overvoltage*
(Transient Overvoltage, tini = 10 sec)	VIOTM		6000	Vpeak
Safety Limiting Values
(Maximum values allowed in the event of a failure,
also see Figure 18, Thermal Derating curve.)				°C
Case Temperature	TS		175
Input Current	IS,INPUT		230	mA
Output Power	PS,OUTPUT		600	mW
Insulation Resistance at T , V = 500 V	R	S	³ 109	W
S IO

*Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section (VDE 0884), for a detailed description.

Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application.

1-170