Page 1
D-Link
Wireless Print Server
Manual
DP-311UDP-311U
DP-311U
DP-311UDP-311U
Building Networks for People
Page 2
Contents
Package Contents ................................................................................3
Introduction............................................................................................4
Wireless Basics ....................................................................................8
Setting up the DP-311U ...................................................................... 10
Getting Started ....................................................................................12
Using the Web Configuration ...............................................................13
TCP/IP Printing for Windows XP ........................................................21
TCP/IP Printing for Windows 2000.....................................................29
TCP/IP Printing for Windows 98SE/Me ..............................................38
Unix/Linux Printing (See PS Admin Manual on CD-ROM) .................. 49
Setting up AppleTalk or LPR Printing in MAC OSX ..............................50
Setting up AppleTalk Printing in MAC OS9 ..........................................55
Networking Basics .............................................................................. 58
Technical Specifications ......................................................................70
Contacting Technical Support .............................................................. 71
Warranty and Registration ................................................................... 72
Appendix: DP-311U Printer Compatibility List ....................................75
2
Page 3
Package Contents
Contents of Package:
D-Link DP-311U
Fast Ethernet Print Server
Manual and Warranty on CD
Printed Quick Installation Guide
If any of the above items are missing, please contact your reseller.
A computer with an installed Ethernet adapter
Windows XP/2000/ME/98SE
Apple Mac OS with AppleTalk
Linux
Internet Explorer 6.0, or Netscape Navigator version 6.0 or
above, with JavaScript enabled
Printer must support required Operating System
System Requirements:
3
Page 4
Introduction
The D-Link DP-311U Print Server is an 802.11b wireless print server that also
connects to your Ethernet/Fast Ethernet network. Now you can locate USB
printer services virtually anywhere in your home or office. The DP-311U manages
the flow of print files from workstations or file servers to connected printers,
delivering print jobs to printers much faster than a file server on a PC acting as a
print server can. With one USB (v1.1) port, the DP-311U can connect to almost
any printer with a USB port.
The DP-311U includes easy-to-use software to install on most Windows-based
networks. Protocol support for TCP/IP, NetBEUI, and AppleTalk are provided to
ensure seamless connection to major networking Operating Systems.
The DP-311U has a built in Web-Based management feature that allows users to
easily configure and manage print queues through TCP/IP. The DP-311U also
supports Telnet as an alternative method to configure the unit.
The DP-311U improves network printing services in the following ways:
The DP-311U delegates print jobs to the connect USB printer. This
provides workload relief to your file servers and allows the file servers’ full
capacity to be used for file access or other direct services to network
users. On peer-to-peer networks, workstations can print directly to the
Print Server without increasing the load of another workstation or server.
The DP-311U’s USB port, version 1.1, can transmit to high-speed laser
printers much faster than a PC’s parallel printer port.
Because the DP-311U is very portable and inexpensive compared to a
PC-based print server, and the Print Server connects to your file servers
through the network, printers can be deployed to locations of maximum
convenience to users.
4
Page 5
The DP-311U offers extraordinary flexibility, operating with all major network
operating systems and protocols:
Windows-based setup and administration software, PS Admin, is supplied with
the Print Server, making configuration and management quick and easy. The
Print Server also supports configuration and management via the Telnet protocol
for networks without Windows-compatible systems.
TCP/IP
UNIX lpr/lpd
Windows NT/2000, Windows 95/98SE/ME, Windows XP
NetWare 5.x NDPS LPR Remote Printing
NetBEUI
Windows 2000/XP, Windows 95/98SE/ME, Microsoft LAN
Manager, IBM LAN Server
AppleTalk
MacOS EtherTalk
External Features
Port Connectors
The DP-311U’s USB port is located on its rear panel. The USB can be configured
using the PS Admin program or the print server’s Telnet interface. (See the PS
Admin User’s Guide, available on the CD that came with the DP-311U, for
information about configuring the print server’s ports.) The Print Server also
supports web configuration permitting users to configure settings through the web
browser. The default IP Address is as follows:
Default IP Address – 192.168.0.10
Subnet Mask – 255.255.255.0
Note:
The PC’s IP Address must be in the same subnet as the Print Server’s IP Address for the
two devices to communicate. (For example, if your Print Server’s IP Address is
192.168.0.10, with a subnet mask of 255.255.255.0, then your computer’s IP Address
should be 192.168.0.x, where x is a value between 1-254, excluding 10.)
5
Page 6
Front Panel LED Indicators
Power / USB
Steady or flashing green light confirms that the Print Server is
powered ON. The LED indicator lights up to show that the Print
Server is transferring print data through the USB port.
Ethernet/WLAN
Steady or flashing green light confirms that the Print Server has a good
connection to the Ethernet or Fast Ethernet network.
The indicator blinks off briefly to indicate that the Print Server is
receiving or transmitting from the network.
LED Indicators
The front panel of the Print Server features four LED indicators:
These four indicators are also used by the Print Server’s Power-ON Self Test
(POST) to indicate any hardware failures.
Power
USB
Ethernet
WLAN
6
Page 7
Rear Panel Connectors
Network Cable Connector
The Print Server’s rear panel features an RJ-45 connector for
connection to 10Base-T Ethernet cabling or 100Base-TX Fast
Ethernet cabling (which should be Category 5 twisted-pair cable).
The port supports the NWay protocol, allowing the Print Server to
automatically detect or negotiate the transmission speed of the
network.
DC Power Connector
The DC power input connector is located on the Print Server’s
rear panel and is labeled DC 5V.
Antenna
Power
Reset
USB
RJ-45
7
Page 8
Wireless Basics
D-Link wireless products are based on industry standards to provide easy-to-use
and compatible high-speed wireless connectivity within your home, business or
public access wireless networks. D-Link wireless products will allow you access to
the data you want, when and where you want it. You will be able to enjoy the
freedom that wireless networking brings.
A WLAN is a cellular computer network that transmits and receives data with radio
signals instead of wires. WLANs are used increasingly in both home and office
environments, and public areas such as airports, coffee shops and universities.
Innovative ways to utilize WLAN technology are helping people to work and
communicate more efficiently. Increased mobility and the absence of cabling and
other fixed infrastructure have proven to be beneficial for many users.
Wireless users can use the same applications they use on a wired network.
Wireless adapter cards used on laptop and desktop systems support the same
protocols as Ethernet adapter cards.
People use wireless LAN technology for many different purposes:
Mobility - Productivity increases when people have access to data in any location
within the operating range of the WLAN. Management decisions based on realtime information can significantly improve worker efficiency.
Low Implementation Costs – WLANs are easy to set up, manage, change and
relocate. Networks that frequently change can benefit from WLANs ease of
implementation. WLANs can operate in locations where installation of wiring may
be impractical.
Installation and Network Expansion - Installing a WLAN system can be fast and
easy and can eliminate the need to pull cable through walls and ceilings. Wireless
technology allows the network to go where wires cannot go - even outside the
home or office.
Scalability – WLANs can be configured in a variety of topologies to meet the needs
of specific applications and installations. Configurations are easily changed and
range from peer-to-peer networks suitable for a small number of users to larger
infrastructure networks to accommodate hundreds or thousands of users,
depending on the number of wireless devices deployed.
Inexpensive Solution - Wireless network devices are as competitively priced as
conventional Ethernet network devices.
8
Page 9
Wireless Basics (cont.)
Standards-Based Technology
Based on the IEEE 802.11b standard, the DP-311U is interoperable with existing
compatible 2.4GHz wireless technology with data transfer speeds of up to 11Mbps
when used with other D-Link Air devices.
Installation Considerations
The D-Link Air DP-311U lets you print through your network, using a wireless
connection, from virtually anywhere within its operating range. Keep in mind,
however, that the number, thickness and location of walls, ceilings, or other objects
that the wireless signals must pass through, may limit the range. Typical ranges
vary depending on the types of materials and background RF (radio frequency)
noise in your home or business. The key to maximizing wireless range is to follow
these basic guidelines:
Keep the antenna of the DP-311U in an upright position
1.
2.
Keep the number of walls and ceilings between the DP-311U and other
network devices to a minimum - each wall or ceiling can reduce your D-Link
wireless product’s range from 3-90 feet (1-30 meters.) Position your devices
so that the number of walls or ceilings is minimized.
3.
Be aware of the direct line between network devices. A wall that is 1.5 feet thick
(.5 meters), at a 45-degree angle appears to be almost 3 feet (1 meter) thick. At
a 2-degree angle it looks over 42 feet (14 meters). Position devices so that the
signal will travel straight through a wall or ceiling (instead of at an angle) for
better reception.
4.
Building Materials can impede the wireless signal - a solid metal door or
aluminum studs may have a negative effect on range. Try to position wireless
devices and computers with wireless adapters so that the signal passes
through drywall or open doorways and not other materials.
Keep your product away (at least 3-6 feet or 1-2 meters) from electrical
5.
devices or appliances that generate extreme RF noise.
9
Page 10
Setting up the DP-311U
Installing the Print Server
WARNING: Configuration problems may result if the Print Server is powered up without
first establishing its network connection. Follow this procedure to avoid complications at
the configuration stage.
1.
Confirm proper operation of the printer to be connected to the DP-311U,
When you have confirmed proper operation of the USB printer, switch it the
2.
power OFF.
Confirm that your network is operating normally.3.
Connect the DP-311U RJ-45 Connector to the network, using a straight
4.
through CAT5 cable..
While the printer is powered OFF, install the USB printer cable to connect the
5.
printer’s USB port to the USB port of the Print Server.
Switch on the connected printer.6.
7.
Plug the AC power adapter’s DC output plug into the DC 5V power socket on
the rear panel of the Print Server.
Plug the power adapter into a power outlet. This will supply power to the Print
8.
Server, as it has no external power switch. The green Power LED on the
Print Server’s front panel should illuminate steadily, and the Print Server’s
Self-Test will proceed.
10
Page 11
Power ON Self-Test
Every DP-311U has been factory-tested to operate properly.
When the DP-311U is powered ON, it also automatically performs a Self-Test on
each of its major components. The final result of the Self-Test is signaled by the
state of the USB LED indicator following the Self-Test. Preliminary to the actual
component tests, the LED indicators are tested to confirm their steady and
flashing operation.
Immediately after power-up, all three of the green LEDs should illuminate steadily
for several seconds. Then the USB LED should flash ON three times.
Irregularity of the LED during this LED test may mean there is a problem with the
LED itself.
The actual component tests immediately follow the LED tests. A normal (no fault)
result is signaled by a flashing of the USB LED, followed by a darkened LED.
If the Self-Test routine detects any component error, then following the LED tests
the Self-Test will halt and the LEDs will continuously signal the error according to
the following table. In the event of any such error signal, contact your dealer for
correction of the faulty unit.
USB LED
low speed flashing
steady ON
1 long 2 short
1 long 3 short
1 long 5 short
1 long 6 short
1 long 7 short
1 long 11 short
1 long 15 short
1 long 16 short
1 long 17short
1 long 18 short
Faulty Component
Need to reload firmware
DRAM error
Timer INT error
Flash Protected
Flash Erase/Program error
LAN Controller error
LAN memory error
LAN I/O base error
Wireless LAN card detect error
Wireless LAN card CIS error
Wireless LAN card I/O error
USB error
11
Page 12
Getting Started
Below is a sample network using the DP-311U. The DP-311U has a built- in
Web-based management feature that allows users to easily configure and
manage their print queue through TCP/IP.
Warning!
Only a USB printer may be connected to the USB port of the DP-311U. Do not
connect any other USB devices to the USB port of the DP-301U; to do so, may
damage the unit and will void the warranty for this product.
For a list of printers that are compatible with the DP-311U, please see the
Appendix in this manual. The compatibility list is not comprehensive. Even if it
is not included in the list, your printer may be compatible with the DP-311U.
12
Page 13
Using the Web Configuration
Open your web browser and type http://192.168.0.10 in the address box, and
press <Enter>. This set of numbers is the default IP Address of your Print Server.
Please note that the PC’s IP Address must correspond with the Print
Server’s IP Address in the same segment for the two devices to
communicate.
When you entered the default IP address, the main screen of the Print Server’s
configuration will appear (see below). In addition to the product information, you can
access and control the Print Server’s configuration through four links on the top of
this main screen: Home, Configuration, Network, Tools, and Help.
13
Page 14
Home
Click on Home tab from the tools bar of the main screen to display information of
the DP-311U’s System Status and Printer Status.
System Status and Printer Status
When you choose and enter the Home tab, it will show you the system information
(see below), providing general information regarding the Print Server. Click on the
<Refresh> button to acquire the most updated information. Once a printer is
connected to the Print Server, the Printer Status will show [Online].
Server Name: The name assigned to the Print Server.
Model: The model of the Print Server.
Hardware Version: The version of the hardware on the Print Server.
Firmware Version: The version of the firmware and release date on the
Print Server.
MAC Address: The MAC address of the Ethernet port.
IP Address: The IP Address of the Print Server.
Up Time: The length of time the Print Server has been up.
14
Page 15
Configuration
Click on Configuration tab from the tools bar of the main screen to enter the Configuration Page; it provides the configuration options that include System Device
and Port Setting
System Device and Port Setting
This option will show you settings required to configure the DP-311U Print Server.
Consult your printers owner manual for the PJL(Printer Job Language) and print
speed supported on your printer. Click the <Save> button on the bottom of the
configuration page to ensure the settings are updated and saved.
15
Page 16
Server Name: The name assigned to the Print Server.
Location: (optional) Input a comment indicating where the Print Server is
located.
Admin Contact: (Optional) Administrator name for the Print Server.
Password: By default the DP-311U does not have a password. This is a security
risk; it is recommended that you enter a password for the Print Server.
Port Name: This is the assigned name for the USB port.
Description: (Optional) A brief description for the USB port.
Speed: Printer port speed, High or Low.
PJL Printer: This feature is used to support Hewlett-Packard PJL (Printer Job
Language) standard for bi-directional printing.
Connection Mode: Ad-Hoc refers to two or more 802.11b wireless devices that
communicate directly with one another without using an access point or any
connection to a wired network. Infrastructure refers to an 802.11 network in which
wireless devices communicate with each other by first going through an Access
Point (AP) or wireless router.
ESS-ID: The workgroup name of your Wireless Network. All wireless devices must
all have the same SSID to communicate on the Wireless Network. All D-Link
Wireless devices have the default SSID of default, all lower case.
Wireless Channel: Displays the channel information. Make sure your the setting
here matches the setting on your access point.
Transmission Rate: You can adjust the transmission rate to get the best signal
possible depending on your usage and environment.
WEP Key Encryption: 64 bit WEP encryption uses a 10 hexidecimal character
key. 128 bit WEP uses a 26 hexidecimal character key. The WEP encryption key
must match the WEP settings on your AP or wireless router to connect properly.
WEP Encryption: Enter the WEP key that you wish to use in this field.
Confirm WEP Key: After typing in your WEP key, confirm the WEP Key in this
field.
16
Page 17
Network
Click on the Network tab from the tools bar of the main screen to enter the Network
Page; it provides network protocol configuration options that include TCP/IP,
NetBEUI and AppleTalk
TCP/IP Protocol
The TCP/IP Protocol section will show you the settings required to configure the
DP-311U Print Server for TCP/IP printing. If you forget your IP Address, you can use
the PS Admin program to configure the DP-311U Print Server. The default IP Address is 192.168.0.10. Click the <Save> button to ensure the settings are updated
and saved. NOTE: If you change and save the IP Address of the DP-311U, you
would have to make similar changes on your web browser to access the web
configuration again.
NetBEUI Protocol
The NetBEUI Protocol section will show you the settings required to configure the
DP-311U Print Server for NetBEUI printing. Click the <Save> button to ensure the
settings are updated and saved.
AppleTalk Protocol
The AppleTalk Protocol section will show you the settings required to configure the
DP-311U Print Server for AppleTalk printing. Click the <Save> button to ensure the
settings are updated and saved.
17
Page 18
Network
18
Page 19
Tools
Click on the Tools link from the tools bar of the main screen to enter the Tools
Page; it provides the control options that include Print Test and Reset.
Print Test
Print Test section will allow you to send an ASCII text page from the print server to
your printer. Your USB printer will have to support native DOS mode for the test
page to print.
Reset
Reset section will allow you to reset your print server. Click the <Yes> button to
activate the reset process. Reset will restart the print server. Factory reset will
reset all settings to factory default and restart the print server. Default IP address of
the print server will be 192.168.0.10 after factory reset.
19
Page 20
Help
Click on the Help link from the tools bar of the main screen to enter the Help Page,
it provides a link to D-Link’s support website. D-Link’s support website will provide
the most up to date information on your DP-311U Print Server. Please check the
website regularly for product and firmware updates.
20
Page 21
TCP/IP Printing for Windows XP
Open the web browser, and type in the IP Address of the DP-311U.
For example, type http://192.168.0.10 into the Location or Address field. Press
the Enter or (Return) Key.
Note:
The PC’s IP Address must be in the same subnet as the Print Server’s IP
Address for the two devices to communicate. (For example, if your Print
Server’s IP Address is 192.168.0.10, with a subnet mask of 255.255.255.0,
then your computer’s IP Address should be 192.168.0.x, where x is a value
between 1-254, excluding 10.) See Networking Basics: Assigning a Static IP
Address in this manual to find out how to change an IP Address.
D-Link DP-301U
21
Page 22
TCP/IP Printing for Windows XP (continued)
At the Configuration window, write down the Port Name for future reference.
You will need this information later in the configuration process.
Select your Connection Mode
Enter the ESS-ID of the remote access point or wireless router you wish to
connect to.
If you would like to set WEP Encryption, select the encryption level and the
key here.
Click Save
22
Page 23
TCP/IP Printing for Windows XP (continued)
When you select TCP/IP Protocol at the Network window, the screen below
appears. (We recommend that you keep the default settings as shown.) If you
need to make changes, make sure to click Save after you have made the
changes. (You may wish to make a note of the IP Address.)
23
Page 24
TCP/IP Printing for Windows XP (continued)
Go to Start > Settings >
Printers and Faxes >
Add a Printer
Click Next
24
Page 25
TCP/IP Printing for Windows XP (continued)
Select Local Printer
Deselect Automatically
detect and install my
Plug and Play printer.
Click Next
Select Create a new port. At the
pull-down menu, highlight
Standard TCP/IP Port.
Click Next
Click Next
25
Page 26
TCP/IP Printing for Windows XP (continued)
Type in the IP
address of the
Print Server (i.e.
192.168.0.10).
The Port Name
will automatically
be filled in.
Select “Custom”
Then click on Settings.
Select “LPR”
Input the port name of
the port being used by
the printer
Click OK
26
Page 27
TCP/IP Printing for Windows XP (continued)
Click Next
Click Finish
Highlight the printer, as shown.
If the desired printer is not on
the list, click Have Disk and
insert the printer driver disk that
came with your printer to install
the printer drivers.
Click Next
27
Page 28
TCP/IP Printing for Windows XP (continued)
At this screen, you can input a name
for the printer.
Click Next
Click Next
Click Finish
28
Page 29
TCP/IP Printing for Windows 2000
Open the web browser, and type in the IP Address of the DP-311U.
For example, type http://192.168.0.10 into the Location or Address field. Press
the Enter or (Return) Key.
Note:
The PC’s IP Address must be in the same subnet as the Print Server’s IP
Address for the two devices to communicate. (For example, if your Print
Server’s IP Address is 192.168.0.10, with a subnet mask of 255.255.255.0,
then your computer’s IP Address should be 192.168.0.x, where x is a value
between 1-254, excluding 10.)
D-Link DP-301U
29
Page 30
TCP/IP Printing for Windows 2000 (continued)
At the Configuration window, write down the Port Names for future reference.
You will need this information later in the configuration process.
Select your Connection Mode
Enter the ESS-ID of the remote access point or wireless router you wish to
connect to.
If you would like to set WEP Encryption, select the encryption level and the
key here.
Click Save
30
Page 31
TCP/IP Printing for Windows 2000 (continued)
When you select TCP/IP Protocol at the Network window, the screen below
appears. (We recommend that you keep the default settings as shown.) If you
need to make changes, make sure to click Save after you have made the
changes. (You may wish to make a note of the IP Address.)
31
Page 32
TCP/IP Printing for Windows 2000 (continued)
Go to Start > Settings >
Printers
Double-click on the Add
Printer icon.
Click Next
32
Page 33
TCP/IP Printing for Windows 2000 (continued)
Select Local Printer
Click Next
Select Create a new port at the
pull-down menu,
highlight Standard TCP/IP Port.
Click Next
33
Page 34
TCP/IP Printing for Windows 2000 (continued)
Click Next
Type in the IP Address of the Print
Server in the Printer
Name or IP Address field. The
Port Name field will
automatically be filled in.
Click Next
Select “Custom”
Then click on Settings.
34
Page 35
TCP/IP Printing for Windows 2000 (continued)
Select “LPR”
Input the port name of
the port being used by
the printer
Click OK
Click Next
Click Finish
35
Page 36
TCP/IP Printing for Windows 2000 (continued)
Highlight the printer, as shown.
If the desired printer is not on
the list, click Have Disk and
insert the printer driver disk that
came with your printer to install
the printer drivers.
Click Next
At this screen, you can input a
name for the printer.
Click Next
36
Page 37
TCP/IP Printing for Windows 2000 (continued)
Select Do not share this printer
.
Click Next
Select Yes to print a test page
Click Next
Click Finish
The printer is now ready for
printing with Windows
2000 on your network.
37
Page 38
TCP/IP Printing
for Windows 98SE/Me
Open the web browser, and type in the IP Address of the DP-311U.
For example, type http://192.168.0.10 into the Location or Address field. Press
the Enter or (Return) Key.
Note:
The PC’s IP Address must be in the same subnet as the Print Server’s IP
Address for the two devices to communicate. (For example, if your Print
Server’s IP Address is 192.168.0.10, with a subnet mask of 255.255.255.0,
then your computer’s IP Address should be 192.168.0.x, where x is a value
between 1-254, excluding 10.)
D-Link DP-301U
38
Page 39
TCP/IP Printing for Windows 98SE/Me (continued)
At the Configuration window, write down the Port Name for future reference.
You will need this information later in the configuration process. The Port Name
shown here is only an example.
Select your Connection Mode
Enter the ESS-ID of the remote access point or wireless router you wish to
connect to.
If you would like to set WEP Encryption, select the encryption level and the
key here.
Click Save
39
Page 40
TCP/IP Printing for Windows 98SE/Me(continued)
When you select TCP/IP Protocol at the Network window, the screen below
appears. (We recommend that you keep the default settings as shown.) If you
need to make changes, make sure to click Save after you have made the
changes. (You may wish to make a note of the IP Address.)
40
Page 41
TCP/IP Printing for Windows 98SE/Me (continued)
Go to Start > Settings >
Control Panel
Double-click on Network
Click Add
Highlight Client
Click Add
41
Page 42
TCP/IP Printing for Windows 98SE/Me (continued)
At this window,
click Have Disk.
Insert the DP-311U
1.
CD-ROM into your
CD-ROM drive.
Select the letter
representing the
CD-ROM drive on
your computer from
the pull-down menu.
2.
Double-click on
the folder lpr.
33
3
33
22
2
22
44
4
44
3. Highlight lpr.inf
4. Click OK
Click OK to accept the
location of the file.
42
11
1
11
Page 43
TCP/IP Printing for Windows 98SE/Me (continued)
Click OK
You should now be
back to the Network
Properties Page.
Highlight LPR for
TCP/IP Printing.
Click Properties
43
Page 44
TCP/IP Printing for Windows 98SE/Me (continued)
Click Add Port
Type in the IP Address of
the DP-301U. Make sure
the Port Name is accu-
rate. (The Port Name at
right is just an example.)
Click OK
The Port name and IP
Address will be displayed.
(The Port Name at right is
just an example.)
Click OK
44
Page 45
TCP/IP Printing for Windows 98SE/Me (continued)
Click OK
Windows will ask for
a restart.
Click Yes
45
Page 46
TCP/IP Printing for Windows 98SE/Me continued)
Once your computer has rebooted, click on
Start > Settings > Printers > Add Printer
When the Add Printer Wizard
screen appears, Click Next.
Select Network Printer.
Click Next
Type in the path if you know it,
or Click Browse.
46
Page 47
TCP/IP Printing for Windows 98SE/Me (continued)
At the next screen, browse for the printer
port. Highlight the port as shown. (The Port
Name in this window is just an example.)
Click OK
If the network path is not specified, type in
the IP Address of the DP-311U and the Port
Name. (The Port Name shown at right is
just an example.)
Select Yes or No, to answer the question:
Do you print from MS-DOS based programs?
Click Next
Highlight the printer, as shown. If the desired
printer is not on the list, click Have Disk and
insert the printer driver disk that came with
your printer to install the printer drivers.
Click Next
Click Next
47
Page 48
TCP/IP Printing for Windows 98SE/Me (continued)
Select Yes to print
a test page.
Click Finish
Go to Start >
Settings > Printers
Check to see that your
printer is installed.
48
Page 49
Unix/Linux Printing
Please refer to the PS Admin Manual on the CD included with your purchase for
information on setting up the Print Server in Unix/Linux.
49
Page 50
Setting up Apple Talk or LPR
Printing in Mac OS X
Note: Mac OS printing with this print server is supported by Postscript printers only!
With Mac OSX you can use AppleTalk or LPR printers using IP protocols for printing
through Print Servers. Follow the instructions below for setting up the Print Server.
After attaching the Print Server to your network using the directions provided in the
Quick Installation Guide, change the IP Address of your Macintosh to access the
Print Server’s web configuration.
Open your System
Preferences
window and Click
Network.
At the Configure
pull-down menu,
select Manually
50
Page 51
Setting up Apple Talk or LPR Printing
in Mac OS X (continued)
The default IP
Address of the Print
Server is
192.168.0.10.
Manually change
your IP Address to
102.168.0.x, where
x is any number
between 1 and 254
(except 10 which is
the IP Address of
the Print Server.)
The IP Addresses
and Subnet Mask
shown here are
examples only.
Select the AppleTalk
tab in this window
and check Make
AppleTalk Active.
51
Page 52
Setting up Apple Talk or LPR Printing
in Mac OS X (continued)
To print, open a document
and select File > Print
from the menu.
Select Edit Printer
List from the Printer
dialog box.
Click Add Printer
52
Page 53
Setting up Apple Talk or LPR Printing
in Mac OS X (continued)
Select the printing
protocol preferred,
AppleTalk or LPR
Printers using IP.
In this example,
AppleTalk has been
selected.
AppleTalk protocol:
After selecting
AppleTalk the Port
Name of the Print
Server will be displayed. The Port
Name shown here is
an example only.
PS - 116688-U1 Laserwriter
PS - 116688-U1 Laserwriter
Click on the Port to
which the post-script
printer is connected.
Then select the printer model from the dialog box displayed here.
Click Add Printer and the Printer Port configuration is complete.
Select the Printer Port just configured in the Print window.
Click Print to print your document.
53
Page 54
Setting up Apple Talk or LPR Printing
in Mac OS X (continued)
LPR Printers using IP
protocol:
When you select LPR
Printers using IP Protocol, this window will ap-
pear.
Type the IP Address of the
Print Server into the LPR
Printer’s Address field.
In the Queue Name field, type in the Port Name of the post-script printer that is
connected to the Print Server. The Port Name illustrated here is only an example.
Select the printer model from the dialog box.
In the Queue Name field, type in the Port Name of the post-script printer that is
connected to the Print Server. The Port Name illustrated here is only an example.
Select the printer model from the dialog box.
Click Add and the process is complete.
Close all Print Center windows, select the Printer Port that was just selected.
Click Print to print the document.Click Add and the process is complete.
PS-116688 - U1
54
Page 55
Setting up Apple Talk Printing
in Mac OS 9
Note: Mac OS printing with this print server supports Postscript printers only!
The AppleTalk network protocol is used with computers using the MacOS operating
system. It can be used for network communications over standard Ethernet or Fast
Ethernet using the EtherTalk transport, or over a proprietary low-speed LocalTalk
transport.
Your Print Server can be used for network printing to PostScript printers. You can
print from any MacOS computer connected to your Ethernet network, either directly
using an EtherTalk connection, or indirectly through a LocalTalk-to-EtherTalk router.
NOTE: The Chooser name of a printer connected to one of the Print Server’s ports
is the same as its Port Name. If you are using AppleTalk printing, you will need to
make sure that every Port Name is unique among all of the network printers in your
AppleTalk zone. The Port Names shown in this manual are examples only.
Setting up the Print Server for AppleTalk Printing
To set up your Print Server so that it can be used for AppleTalk printing:
Make sure the AppleTalk protocol is enabled in your Macintosh.
Change the IP Address on one of the computers on your network to
192.168.0.x, where x is any number between 11-254.
Type 192.168.0.10 into the address field of your web browser. 192.168.0.10 is
the default IP Address of the DP-311U.
Select the Network tab and scroll to the bottom to the AppleTalk protocol
section
If your AppleTalk network is divided into AppleTalk zones, you will have to
specify which zone the Print Server should be in. You should locate the Print
Server in the same zone as most of the users who will be using it. If your
network is not divided into zones, the AppleTalk Zone field should contain a
single asterisk “*”.
55
Page 56
Printing from MacOS Client Workstations
The exact procedure for selecting a PostScript printer connected to your Print
Server may vary slightly, depending on what printer driver version you are using.
The procedure described below assumes you are using the LaserWriter 8.
To choose a printer connected to your Print Server as your MacOS
workstation’s default printer,
Open the Chooser by selecting Chooser from the Apple menu.
Select the LaserWriter 8 icon on the left. Make sure that AppleTalk is set
to Active.
A list of all networked PostScript printers will be displayed:
Double-click the name of
the Printer Port you wish
to use. The Printer Ports
shown are examples only.
56
PS-116688-U1
Page 57
Printing from MacOS Client Workstations (continued)
If you have not previously
set this printer as the
default, your computer
will prompt you for a
PostScript Printer
Description file. Choose
Select PPD.
Select the appropriate
printer description file for
your printer.
Click Open.
(If your printer is not listed,
click Generic to use a
generic printer
description.)
If you wish to access this setting in the future, you can use the Setup button in the
Chooser window.
The selected printer will become your computer’s default printer. You may need to
choose Page Setup in any applications you have open.
57
Page 58
Networking Basics
Using the Network Setup Wizard in Windows XP
In this section you will learn how to establish a network at home or work, using
Microsoft Windows XP.
Note: Please refer to websites such as
and http://www.microsoft.com/windows2000 for information about networking
computers using Windows 2000, ME or 98SE.
Go to Start>Control Panel>Network Connections
http://www.homenethelp.com
When this screen appears, Click Next
58
Page 59
Networking Basics (continued)
Please follow all
the instructions in
this window:
In this window,
select the
best description of
your computer.
If your computer
connects to the
internet through a
gateway/router,
select the second
option as shown.
Click Next
59
Page 60
Networking Basics
Enter a Computer
description and a
Computer name
(optional.)
Click Next
(continued)
Enter a Workgroup
name. All computers
on your network
should have the
same Workgroup
name.
Click Next
60
Page 61
Networking Basics
Please wait while
the Network
Setup Wizard
applies the
changes.
When the changes
are complete,
Click Next.
(continued)
Please wait while
the Network
Setup Wizard
configures the
computer.
This may take a
few minutes.
61
Page 62
Networking Basics
In this window, select
the best option. In
this example, Create
a Network
Setup Disk has been
selected.
You will run this disk
on each of the
computers on your
network.
Click Next
(continued)
Insert a disk into the
Floppy Disk Drive, in
this case drive A.
Format the disk if you
wish, and Click Next
62
Page 63
Networking Basics
Please wait while the Network Setup Wizard copies the files.
Please read the information under Here’s how in the screen below. After you
complete the Network Setup Wizard you will use the Network Setup Disk to run
the Network Setup Wizard once on each of the computers on your network. To
continue, Click Next.
(continued)
63
Page 64
Networking Basics
(continued)
The new settings will take effect when you restart the computer. Click Yes to
restart the computer.
You have completed configuring this computer. Next, you will need to run the Net-
work Setup Disk on all the other computers on your network. After running the
Network Setup Disk on all your computers, your new wireless network will be
ready to use.
64
Page 65
Networking Basics
(continued)
How to assign a Name to your computer
To name your computer, please follow these directions in Windows XP:
Click Start (in the lower left corner of the screen)
Right-click My Computer
Select Properties and Click
Select the Computer
Name tab in the System
Properties window.
You may enter a
Computer Description
(optional).
To rename the computer
and join a domain, Click
Change.
65
Page 66
Networking Basics
(continued)
How to assign a Name to your Computer
In this window, enter the
Computer name
Select Workgroup and enter
the name of the Workgroup
All computers on your network
must have the same
Workgroup name.
Click OK
How to find your IP Address in Windows XP
The adapter-equipped computers in your network must be in the same IP Address range. To verify the IP Address of the adapter, please do the following:
Right-click on the
Local Area Connection icon in
the task bar
Click on Status
66
Page 67
Networking Basics (continued)
How to find your IP Address in Windows XP
This window will appear.
Click the
Support tab
Click Close
Assigning a Static IP Address in Windows XP/2000
Note: Residential Gateways/Broadband Routers will automatically assign IP
Addresses to the computers on the network, using DHCP (Dynamic Host Configuration Protocol) technology. If you are using a DHCP-capable Gateway/
Broadband Router you will not need to assign Static IP Addresses.
If you are not using a DHCP capable Gateway/Broadband Router, or you need
to assign a Static IP Address, please follow these instructions:
Go to Start
Double-click
Control Panel
67
Page 68
Networking Basics (continued)
Assigning a Static IP Address in Windows XP/2000
Double-click
Network
Connections
Right-click Local Area
Connections
Double-click
Properties
68
Page 69
Networking Basics (continued)
Assigning a Static IP Address
in Windows XP/2000
Click Internet Protocol
(TCP/IP)
Click Properties
Select Use the
following IP Address in
the Internet Protocol
(TCP/IP)Properties
window.
Input your IP Address and
subnet mask. (The IP
Addresses on your network
must be within the same
range. For example, if one
computer has an IP
Address of 192.168.0.2, the
other computers should
have IP Addresses that are
sequential, like 192.168.0.3
and 192.168.0.4. The
subnet mask must be the
same for all the computers
on the network.)
Input your DNS server
addresses. (Note: If you
are entering a DNS server,
you must enter the IP
Address of the Default
Gateway.)
The DNS server information will be supplied
by your ISP (Internet Service Provider.)
Click OK
69
Page 70
Technical Specifications
Printer Connection
Printer Port: USB port (ver 1.1)
Bidirectional Communication:
Hewlett-Packard PJL (Printer Job Language) standard
for bidirectional communication.
Network Connection
Network Standards: IEEE 802.3 10Base-T Ethernet, IEEE 802.11b Wireless Standard
Network Data Transfer Rate: 10/100 Mbps (megabits per second)
Network Connector: RJ-45 connector for 10Base-T Category 5 twisted-pair connection
Network Protocols
Ethernet Frame Types: 802.2, 802.3, Ethernet II, SNAP (auto-switching)
Transport Protocols: TCP/IP, NetBEUI, AppleTalk/EtherTalk, LPR
TCP/IP Protocols Supported: BOOTP, SNMP, Telnet, TFTP, FTP, LPD, RARP, DHCP
Management and Diagnostics
Standard: SNMP
MIBs: MIB-II (RFC 1213)
Diagnostic LED Indicators: Pw, Lk/Act, USB
Environmental and Physical
Power Supply: External power supply providing 5V/ 2.5A
Dimensions: 3.54" x 3.19" x 1.57" (90mm x 81mm x 40mm)
Weight: approx. 5.19 oz. (147g)
Operating Temperature: 32 to122°F (0 to 50°C)
Storage Temperature: -13 to 131°F (-25 to 55°C)
Humidity: 5% to 95% non-condensing
Emissions: FCC Class B, CE Class B, VCCI Class B
70
Page 71
Technical Support
You can find software updates and user documentation on the D-Link website.
D-Link provides free technical support for customers within the United States and within
Canada for the duration of the warranty period on this product.
U.S. and Canadian customers can contact D-Link technical support through our website,
or by phone.
Tech Support for customers within the United States:
D-Link Technical Support over the Telephone:
(877) 453-5465
24 hours a day, seven days a week.
D-Link Technical Support over the Internet:
http://support.dlink.com
email:support@dlink.com
Tech Support for customers within Canada:
D-Link Technical Support over the Telephone:
(800) 361-5265
Monday to Friday 8:30am to 9:00pm EST
D-Link Technical Support over the Internet:
http://support.dlink.ca
email:support@dlink.ca
When contacting technical support, please provide the following information:
• Serial number of the unit
• Model number or product name
• Software type and version number
71
Page 72
Warranty and Registration
Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited
warranty for its product only to the person or entity that originally purchased the product from:
D-Link or its authorized reseller or distributor and
Products purchased and delivered within the fifty states of the United States, the District of
Columbia, U.S. Possessions or Protectorates, U.S. Military Installations, addresses with an APO or
FPO.
Limited Warranty: D-Link warrants that the hardware portion of the D-Link products described below will
be free from material defects in workmanship and materials from the date of original retail purchase of the
product, for the period set forth below applicable to the product type (“Warranty Period”), except as otherwise
stated herein.
1-Year Limited Warranty for the Product(s) is defined as follows:
Hardware (excluding power supplies and fans)One (1) Year
Power Supplies and Fans One (1) Year
Spare parts and spare kits Ninety (90) days
D-Link’s sole obligation shall be to repair or replace the defective Hardware during the Warranty Period at no
charge to the original owner or to refund at D-Link’s sole discretion. Such repair or replacement will be
rendered by D-Link at an Authorized D-Link Service Office. The replacement Hardware need not be new or
have an identical make, model or part. D-Link may in its sole discretion replace the defective Hardware (or any
part thereof) with any reconditioned product that D-Link reasonably determines is substantially equivalent (or
superior) in all material respects to the defective Hardware. Repaired or replacement Hardware will be
warranted for the remainder of the original Warranty Period from the date of original retail purchase. If a
material defect is incapable of correction, or if D-Link determines in its sole discretion that it is not practical to
repair or replace the defective Hardware, the price paid by the original purchaser for the defective Hardware
will be refunded by D-Link upon return to D-Link of the defective Hardware. All Hardware (or part thereof) that
is replaced by D-Link, or for which the purchase price is refunded, shall become the property of D-Link upon
replacement or refund.
Limited Software Warranty: D-Link warrants that the software portion of the product (“Software”) will
substantially conform to D-Link’s then current functional specifications for the Software, as set forth in the
applicable documentation, from the date of original retail purchase of the Software for a period of ninety (90)
days (“Warranty Period”), provided that the Software is properly installed on approved hardware and
operated as contemplated in its documentation. D-Link further warrants that, during the Warranty Period, the
magnetic media on which D-Link delivers the Software will be free of physical defects. D-Link’s sole obligation
shall be to replace the non-conforming Software (or defective media) with software that substantially
conforms to D-Link’s functional specifications for the Software or to refund at D-Link’s sole discretion. Except
as otherwise agreed by D-Link in writing, the replacement Software is provided only to the original licensee,
and is subject to the terms and conditions of the license granted by D-Link for the Software. Software will be
warranted for the remainder of the original Warranty Period from the date or original retail purchase. If a
material non-conformance is incapable of correction, or if D-Link determines in its sole discretion that it is not
practical to replace the non-conforming Software, the price paid by the original licensee for the nonconforming Software will be refunded by D-Link; provided that the non-conforming Software (and all copies
thereof) is first returned to D-Link. The license granted respecting any Software for which a refund is given
automatically terminates.
Non-Applicability of Warranty: The Limited Warranty provided hereunder for hardware and software of
D-Link’s products will not be applied to and does not cover any refurbished product and any product
purchased through the inventory clearance or liquidation sale or other sales in which D-Link, the sellers, or the
liquidators expressly disclaim their warranty obligation pertaining to the product and in that case, the product
is being sold “As-Is” without any warranty whatsoever including, without limitation, the Limited Warranty as
described herein, notwithstanding anything stated herein to the contrary.
Submitting A Claim: The customer shall return the product to the original purchase point based on its return
policy. In case the return policy period has expired and the product is within warranty, the customer shall
submit a claim to D-Link as outlined below:
The customer must submit with the product as part of the claim a written description of the
Hardware defect or Software nonconformance in sufficient detail to allow D-Link to confirm the
same.
72
Page 73
The original product owner must obtain a Return Material Authorization (“RMA”) number from the
Authorized D-Link Service Office and, if requested, provide written proof of purchase of the
product (such as a copy of the dated purchase invoice for the product) before the warranty service
is provided.
After an RMA number is issued, the defective product must be packaged securely in the original or
other suitable shipping package to ensure that it will not be damaged in transit, and the RMA number
must be prominently marked on the outside of the package. Do not include any manuals or
accessories in the shipping package. D-Link will only replace the defective portion of the Product
and will not ship back any accessories.
The customer is responsible for all in-bound shipping charges to D-Link. No Cash on Delivery
(“COD”) is allowed. Products sent COD will either be rejected by D-Link or become the property of
D-Link. Products shall be fully insured by the customer and shipped to D-Link Systems, Inc., 53
Discovery Drive, Irvine, CA 92618. D-Link will not be held responsible for any packages that are
lost in transit to D-Link. The repaired or replaced packages will be shipped to the customer via UPS
Ground or any common carrier selected by D-Link, with shipping charges prepaid. Expedited
shipping is available if shipping charges are prepaid by the customer and upon request.
D-Link may reject or return any product that is not packaged and shipped in strict compliance with the foregoing
requirements, or for which an RMA number is not visible from the outside of the package. The product owner
agrees to pay D-Link’s reasonable handling and return shipping charges for any product that is not packaged
and shipped in accordance with the foregoing requirements, or that is determined by D-Link not to be defective
or non-conforming.
What Is Not Covered: This limited warranty provided by D-Link does not cover: Products, if in D-Link’s
judgment, have been subjected to abuse, accident, alteration, modification, tampering, negligence, misuse,
faulty installation, lack of reasonable care, repair or service in any way that is not contemplated in the
documentation for the product, or if the model or serial number has been altered, tampered with, defaced or
removed; Initial installation, installation and removal of the product for repair, and shipping costs; Operational
adjustments covered in the operating manual for the product, and normal maintenance; Damage that occurs in
shipment, due to act of God, failures due to power surge, and cosmetic damage; Any hardware, software,
firmware or other products or services provided by anyone other than D-Link; Products that have been
purchased from inventory clearance or liquidation sales or other sales in which D-Link, the sellers, or the
liquidators expressly disclaim their warranty obligation pertaining to the product. Repair by anyone other than
D-Link or an Authorized D-Link Service Office will void this Warranty.
Disclaimer of Other Warranties: EXCEPT FOR THE LIMITED WARRANTY SPECIFIED HEREIN, THE
PRODUCT IS PROVIDED “AS-IS” WITHOUT ANY WARRANTY OF ANY KIND WHATSOEVER INCLUDING,
WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE
AND NON-INFRINGEMENT. IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN ANY TERRITORY WHERE
A PRODUCT IS SOLD, THE DURATION OF SUCH IMPLIED WARRANTY SHALL BE LIMITED TO NINETY (90)
DAYS. EXCEPT AS EXPRESSLY COVERED UNDER THE LIMITED WARRANTY PROVIDED HEREIN, THE ENTIRE
RISK AS TO THE QUALITY, SELECTION AND PERFORMANCE OF THE PRODUCT IS WITH THE PURCHASER OF
THE PRODUCT.
Limitation of Liability: TO THE MAXIMUM EXTENT PERMITTED BY LAW, D-LINK IS NOT LIABLE UNDER
ANY CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHER LEGAL OR EQUITABLE THEORY FOR ANY
LOSS OF USE OF THE PRODUCT, INCONVENIENCE OR DAMAGES OF ANY CHARACTER, WHETHER DIRECT,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR LOSS OF
GOODWILL, LOSS OF REVENUE OR PROFIT, WORK STOPPAGE, COMPUTER FAILURE OR MALFUNCTION,
FAILURE OF OTHER EQUIPMENT OR COMPUTER PROGRAMS TO WHICH D-LINK’S PRODUCT IS CONNECTED
WITH, LOSS OF INFORMATION OR DATA CONTAINED IN, STORED ON, OR INTEGRATED WITH ANY PRODUCT
RETURNED TO D-LINK FOR WARRANTY SERVICE) RESULTING FROM THE USE OF THE PRODUCT, RELATING
TO WARRANTY SERVICE, OR ARISING OUT OF ANY BREACH OF THIS LIMITED WARRANTY, EVEN IF D-LINK
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE SOLE REMEDY FOR A BREACH OF THE
FOREGOING LIMITED WARRANTY IS REPAIR, REPLACEMENT OR REFUND OF THE DEFECTIVE OR NONCONFORMING PRODUCT. THE MAXIMUM LIABILITY OF D-LINK UNDER THIS WARRANTY IS LIMITED TO THE
PURCHASE PRICE OF THE PRODUCT COVERED BY THE WARRANTY. THE FOREGOING EXPRESS WRITTEN
WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ANY OTHER WARRANTIES OR
REMEDIES, EXPRESS, IMPLIED OR STATUTORY.
73
Page 74
Governing Law: This Limited Warranty shall be governed by the laws of the State of California. Some states
do not allow exclusion or limitation of incidental or consequential damages, or limitations on how long an implied
warranty lasts, so the foregoing limitations and exclusions may not apply. This limited warranty provides
specific legal rights and the product owner may also have other rights which vary from state to state.
Trademarks: D-Link is a registered trademark of D-Link Systems, Inc. Other trademarks or registered
trademarks are the property of their respective manufacturers or owners.
Copyright Statement: No part of this publication or documentation accompanying this Product may be
reproduced in any form or by any means or used to make any derivative such as translation, transformation,
or adaptation without permission from D-Link Corporation/D-Link Systems, Inc., as stipulated by the United
States Copyright Act of 1976. Contents are subject to change without prior notice. Copyright© 2002 by D-Link
Corporation/D-Link Systems, Inc. All rights reserved.
CE Mark Warning: This is a Class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communication. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with a minimum distance of about 8 inches (20cm) between the
radiator and your body.
This transmitter must not be co-located or operated in conjunction with any other antenna or transmiter.
Register your D-Link product online at http://support.dlink.com/register/
74
(03/17/03)
Page 75
Appendix:
DP-311U Printer Compatibility List For Windows
The Canon Printer
Canon BJC-55, 85
Canon S100SP
Canon S200SP
Canon S300
Canon S330
Canon S400SP
Canon S450
Canon S520
Canon S600
Canon S750
Canon S4500
Canon S6300
Canon S9000
The Epson Printer
Epson Stylus Color 900
Epson Stylus Color 1160
Epson Stylus Color 2200
Epson Stylus Photo 720
Epson Stylus Photo 810, 820, 830, 890
Epson Stylus Photo 900
Epson Stylus Photo 1280, 1290
Epson Stylus C41UX, C405, C42UX
Epson Stylus C60, C61, C62
Epson Stylus C80, C82
The Lexmark Printer
Lexmark Z13
Lexmark Z25
Lexmark Z33
Lexmark Z35
Lexmark Z43
Lexmark Z45
Lexmark Z53
The HP Printer
HP DeskJet 640C, 656C
HP DeskJet 845C
HP DeskJet 920C
HP DeskJet 948C
HP DeskJet 960C
HP DeskJet 990Cxi, 995C
HP DeskJet 1125C, 1180C
HP DeskJet 1220C
HP DeskJet 3320
HP DeskJet 3420, 3425
HP Color Inkjet CP1700
HP LaserJet 1200
HP LaserJet 2200, 2200d
75
Page 76
Appendix: DP-311U Printer Compatibility List for Windows (continued)
The Lexmark Printer
Lexmark 4039 10R
Lexmark 5700
Lexmark Optra Color 45
Lexmark Optra C710
Lexmark Optra E, E+, E310
Lexmark Optra K1220
Lexmark Optra M410, M412
Lexmark Optra N
Lexmark Optra R+
Lexmark Optra S1250, S1855
Lexmark Optra SC-1275
Lexmark Optra SE-3455
Lexmark Optra T614
Lexmark Optra W810
Lexmark Z53
Other printers from the brands listed above may also be supported.
For an updated compatibility list please visit: http://www.support.dlink.com
76
Loading...