GAS RANGE
for residential use only
Model: DEFSGG 24 SS
•INSTALLATION INSTRUCTIONS
IMPORTANT - PLEASE READ AND FOLLOW
IMPORTANT - PLEASE READ AND FOLLOW
Before beginning, please read these instructions completely and carefully.
Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty.
Please observe all local and national codes and ordinances.
Please ensure that this product is properly grounded.
The installer should leave these instructions with the consumer who should retain for local inspector's use and for future reference.
The electrical plug should always be accessible.
Installation must conform with local codes or in the absence of codes, the National Fuel Gas Code ANSIZ223.1 - Iatest edition. Electrical installation must be in accordance with the National Electrical Code, ANSI/NFPA70 - latest edition and/or local codes. IN CANADA: Installation must be in accordance with the current CAN/CGA-B149.1 National Gas Installation Code or CAN/CGA-B149.2, Propane Installation Code and/or local codes. Electrical installation must be in accordance with the current CSA C22.1 Canadian Electrical Codes Part 1 and/or local codes.
INSTALLATION IN MANUFACTURED (MOBILE) HOME: The installation must conform with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 [formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD (Part 280)] or, when such standard is not applicable, the Standard for Manufactured Home Installations, ANSI/NCSBCS A225.1, or with local codes where applicable.
INSTALLATION IN RECREATIONAL PARK TRAILERS: The installation must conform with state or other codes or, in the absence of such codes, with the Standard for Recreational Park Trailers, ANSI A119.5.
Installation of any gas-fired equipment should be made by a Iicensed plumber. A manual gas shut-off valve must be installed in the gas supply line ahead of the appliance in the gas stream for safety and ease of service.
If an external electrical source is utilized, the appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the national Electrical Code, ANSI/NFPA 70.
This range is supplied with a protective film on steel and aluminium parts. This film must be removed before installing/using the appliance.
FOR INSTALLER ONLY
THIS RANGE IS FOR RESIDENTIAL USE ONLY
WARNING |
• ALL RANGES CAN TIP |
• INJURY TO PERSON COULD RESULT |
• INSTALL ANTI-TIP DEVICE PACKED |
WITH RANGE |
• SEE INSTALLATION INSTRUCTIONS |
WARNING: IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH.
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS:
•Do not try to light any appliance.
•Do not touch any electrical switch; do not use any phone in your building.
•lmmediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.
•lf you cannot reach your gas supplier, call the fire department.
Installation and service must be performed by a qualified installer, service agency, or the gas supplier.
2
DATA PLATE
CONVERSION LABEL
This appliance is designed and manufactured solely for the cooking of domestic (household) food and in not suitable for any none domestic application and therefore should not be used in a commercial environmement.
The appliance guarantee will be void if the appliance is used within a none domestic environnement i.e. a semi commercial, commercial or communal environment.
3
INSTALLATION INSTRUCTIONS
WARNING!
THIS APPLIANCE HAS TO BE INSTALLED BY A QUALIFIED INSTALLER.
Improper installation, adjustment, alteration, services, or maintenance can cause injury or property damage. Consult a qualified installer, service agent, or the gas supplier.
IMPORTANT: The use of suitable protective clothing/gloves is recommended when handling, installing of this appliance.
TOOLS NEEDED FOR INSTALLATION (NOT SUPPLIED WITH THE APPLIANCE)
|
|
T-handle |
|
Tape |
Screwdriver |
2 - Wrench |
wrench |
Pencil |
measure |
Suitable protective |
Hammer |
Adjustable |
Adjustable |
Drill |
gloves |
|
wrench |
pliers |
4
GENERAL INFORMATION
1.Installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1-Latest Edition.
2.Installation in manufactured (mobile) home: installation must conform with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 [formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD (Part 280)] or, when such standard is not applicable, the Standard for Manufactured Home Installations, ANSI/NCSBCS A225.1, or with local codes where applicable.
3.Installation in Recreational Park Trailers: installation must conforms with state or other codes or, in the absence of such codes, with the Standard for Recreational Park Trailers, ANSI A119.5.
4. 
WARNING!!
This appliance shall not be used for space heating. This information is based on safety considerations.
5.AlI openings in the wall behind the appliance and in the floor under the appliance shall be sealed.
6.Keep appliance area clear and free from combustible materials, gasoline, and other flammable vapors.
7.Do not obstruct the flow of combustion and ventilation air.
8.Disconnect the electrical supply to the appliance before servicing.
9.When removing appliance for cleaning and/or service;
A.Shut off gas at main supply.
B.Disconnect AC power supply.
C.Disconnect gas line to the inlet pipe.
D.Carefully remove the range by pulling outward. CAUTION: Range is heavy; use care in handling.
10.Electrical Requirement
Electrical installation should comply with national and local codes.
11.Air Supply and Ventilation
The installer must refers to local/national codes.
12.Gas Manifold Pressure
Natural gas - 4.0” W.C.P. LP/Propane - 11.0” W.C.P.
13.The misuse of oven door (e.g. stepping, sitting, or leaning on them) can result in potential hazards and/or injuries.
14.When installing or removing the range for service, a rolling lift jack should be used. Do not push against any of the edges of the range in an attempt to slide it into or out of the installation. Pushing or pulling a range (rather than using a lift jack) also increases the possibility of bending the leg spindles or the internal coupling connectors.
WARNING!!
ELECTRICAL GROUNDING INSTRUCTIONS
The range must be electrically grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA No. 70-latest edition. Installation should be made by a Iicensed electrician.
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED.
If an external electrical source is utilized, the installation must be electrically grounded in accordance with local codes or, in the absence of local codes, with the national Electrical Code, ANSI/NFPA 70.
This appliance is equipped with a three-prong grounding plug for your protection against shock hazard and should be plugged directly into a properly grounded socket.
Do not under any circumstances cut or remove the third (ground) prong from the power plug.
REPLACEMENT PARTS
Only authorized replacement parts may be used in performing service on the range. Replacement parts are available from factory authorized parts distributors. Contact the nearest parts distributor in your area.
5
4" 7/16 |
(113 mm) |
MIN 35" 7/16 (900 mm) |
MAX 36" 7/32 (920 mm) |
|
|
24" |
|
(611. |
5/64 |
6 |
|
|
mm) |
Fig. 1.1
23" |
7/8 |
||
|
mm) |
||
.5 |
|||
|
|||
(606 |
|
|
|
installation
PROXIMITY TO SIDE CABINETS
1.This range may be installed directly adjacent to existing 36" (914 mm) high base cabinets.
Range dimensions:
•width: 23” 7/8 (606.5 mm)
•depth: 24” 5/64 (611.6 mm)
•height (without backguard): MIN 35” 7/16 (900 mm) - MAX 36” 7/32 (920 mm)
•backguard (height): 4” 7/16 (113 mm)
Gas line opening:
Wall - 5” 57/64 (150 mm) from the floor; 11” 15/16 (303 mm) from the rear left side of the range.
Grounded outlet: the electric cord with 3-prong ground plug has a length of 72” (1830 mm). Grounded outlet should be located 5” 57/64 (150 mm) from the floor and 11” 15/16 (303 mm) from the rear right side of the range.
2.The range CANNOT be installed directly adjacent to sidewalls, tall cabinets, tall appliances, or other side vertical surfaces above 36” (914 mm) high.
There must be a minimum of 3” (76 mm) side clearance from the range to such combustible surfaces TO THE LEFT above the 36” (914 mm) high countertop; or there must be a minimum of 11” 13/16 (300 mm) side clearance from the range to such combustible surfaces TO THE RIGHT above the 36” (914 mm) high countertop.
IMPORTANT: One side (left or right) above the 36” (914 mm) high countertop must always be kept clear.
3.The maximum upper cabinet depth recommended is 13” (330 mm). Wall cabinet above the range must be a minimum of 30” (762 mm) above the countertop for a width of minimum 24” (609.6 mm): it has to be centred with the range. Side wall cabinets above the range must be a minimum of 18” (457 mm) above the countertop.
GAS AND ELECTRIC CONNECTION
Dotted line showing the position of the range when installed
Area for GAS connection
11" 15/16 |
11" |
15/16 |
|||
(303 |
mm) |
||||
(303 |
mm) |
||||
|
|||||
|
|
||||
|
|
|
|
||
Area for ELECTRICAL connection
5" 57/64 (150 mm)
Fig. 1.2
6
Loading...