Canon XH G1S, XH A1S Instruction Manual

PUB. DIM-894

English

Français

Español

HD Video Camera Recorder

Instruction Manual

COPY

Caméscope et lecteur vidéo HD

Manuel d'instruction

Videocámara y grabadora HD

Manual de Instrucciones

NTSC

Introduction

Important Usage Instructions

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

WARNING:

TO REDUCE THE RISK OF ELECTRIC SHOCK AND TO REDUCE ANNOYING INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY.

COPYRIGHT WARNING: Unauthorized recording of copyrighted materials may infringe on the rights of copyright owners and be contrary to copyright laws.

HD Video Camera Recorder, XH G1S A / XH A1S A Systems. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and use in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules. Do not make any changes or modifications to the equipment unless otherwise specified in the manual. If such changes or modifications should be made, you could be required to stop operation of the equipment. Canon U.S.A. Inc. One Canon Plaza, Lake Success, NY 11042, U.S.A. Tel No. (516)328-5600

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

The Mains plug is used as the disconnect device. The Mains plug shall remain readily operable to disconnect the plug in case of an accident.

mportant Warning

COPY

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure, that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point, within an equilateral triangle, is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

IMPORTANT SAFETY INSTRUCTIONS

In these safety instructions the word “product” refers to the Canon HD Video Camera Recorder XH G1S A /

H A1S A and all its accessories.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

8. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

9. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

10. Only use attachments/accessories specified by the manufacturer.

11. Unplug this apparatus during lightning storms or when unused for long periods of time.

12. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

13. Read Instructions — All the safety and operating instructions should be read before the product is operated.

14. Retain Instructions — The safety and operating instructions should be retained for future reference.

15. Heed Warnings — All warnings on the product and in the operating instructions should be adhered to.

16. Follow Instructions — All operating and maintenance instructions should be followed.

COPY

17. Cleaning — Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. The product should be cleaned only as recommended in this manual.

18. Accessories — Do not use accessories not recommended in this manual as they may be hazardous.

19. Avoid magnetic or electric fields — Do not use the camera close to TV transmitters, portable communication devices or other sources of electric or magnetic radiation. They may cause picture interference, or permanently damage the camera.

20. Water and Moisture — Hazard of electric shock — Do not use this product near water or in rainy/moist situations.

21. Placing or Moving — Do not place on an unstable cart, stand, tripod, bracket or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

22. Power Sources — The CA-920 Compact Power Adapter should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. Regarding other power sources such as battery power, refer to instructions in this manual.

23. Polarization — The CA-920 Compact Power Adapter is equipped with a polarized 2-prong plug (a plug having one blade wider than the other). The 2-prong polarized plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug still fails to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

24. Power Cord Protection — Power cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them. Pay particular attention to plugs and the point from which the cords exit the product.

Introduction

25. Outdoor Antenna Grounding — If an outside antenna is connected to the product, be sure the antenna is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code, ANSI / NFPA No. 70—1984, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See figure 1.

Fig.1

EXAMPLE OF ANTENNA GROUNDING AS PER N AT IONAL ELECTRICAL CODE

ANTENNA LEAD IN WIRE

GROUND CLAMP

ELECTRIC SERVICE EQUIPMENT

NEC - NATIONAL ELECTRICAL CODE

26. Lightning — For added protection of this product during a lightning storm, or when it is left unattended and unused for long periods of time, disconnect it from the wall outlet and disconnect the antenna. This will prevent damage to the product due to lightning and power-line surges.

27. Power Lines — An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

28. Overloading — Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM

(NEC ART 250. PART H)

29. Objects and Liquid Entry — Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Be careful not to spill liquid of any kind onto the product.

30. Servicing — Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

31. Damage Requiring Service — Disconnect this product from the wall outlet and all power sources including battery, and refer servicing to qualified service personnel under the following conditions: a. When the power-supply cord or plug is damaged. b.If any liquid has been spilled onto, or objects have

fallen into, the product. c. If the product has been exposed to rain or water. d.If the product does not operate normally even if you

follow the operating instructions. Adjust only those

controls that are covered by the operation

instructions. Improper adjustment of other controls

may result in damage and will often require

extensive work by a qualified technician to restore

the product to its normal operation. e. If the product has been dropped or the cabinet has

been damaged. f. When the product exhibits a distinct change in

performance. This indicates a need for service.

32. Replacement Parts — When replacement parts are required, be sure the service technician has used replacement parts that are specified by Canon or that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.

33. Safety Check — Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in safe operating order.

34. Heat — The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

When replacement of power supply is required, please return it to the responsible nearest Canon Service Center and please replace it with the same type number CA-920.

The Adapter can be used with a power supply between 100 and 240 V AC. Contact your Canon dealer for information about plug adapter for overseas use.

COPY

The XH G1S / XH A1S - A Broad Range of Capabilities

Ultimate HD Quality

Improved lens with 20x zoom The lens features not only 20x zoom but also improved operability thanks to the knurled focus, zoom, and iris rings. In addition, you can now manually focus while using the zoom.

3CCD system By using three 1/3-in. CCDs (each with a total of 1.67 mega pixels and 1,440x1,080 effective pixels), the camcorder offers a horizontal resolution of 800 TV lines, the highest in HDV standard.

DIGIC DV II image processor The next generation of Canon’s video processing engine ensures optimal video quality and color reproduction for high-definition video.

Versatile Artistic Expression

HDV native 1080/24p, 1080/30p recording Use the 24F or 30F mode for video recordings compliant with native recordings according to HDV specifications ( 42). Whatever your video needs –TV programs, commercials, music videos or movies– you can shoot it with the XH G1S / XH A1S.

Custom presets Enjoy unparalleled image control to deliver the “look” you want. The camcorder offers 23 customizable parameters you can easily save and exchange as custom preset files ( 89).

Introduction

Advanced Professional Features

Pro level connectivity An industry-standard HD/SD SDI terminal for uncompressed HD signal output, embedded audio and SMPTE time code (LTC) are just a few of the features of the XH G1S that give it the functionality of professional broadcast cameras.

Synchronization Genlock synchronization, as well as a TIME CODE terminal, allow the XH G1S to be part of any multi-camera shooting setup.

Enhanced customization Custom functions ( 97) and custom display ( 103) options give you even more freedom to control many aspects of the camcorder’s operation.

And More

Audio options The camcorder is equipped with two sets of XLR audio input terminals with phantom power supply. Record audio using both audio inputs or combine one audio input and the built-in microphone. You can also activate the audio peak limiter ( 51) to avoid distortions during manual audio level adjustment.

Reduced audio noise Unwanted audio noise due to vibrations has been reduced as a result of an improvement to the external microphone holder’s design.

Added and improved functionality Push AE ( 59) • Gain fine-tuning in 0.5 dB increments ( 64) • Focus limit ( 40) • Eye cup attachment ( 19) • Selective NR ( 71) • Audio output level selection (83) • and more!

COPY

About this Manual

LAY

SETUTUP/P/

ANGUAUAGEGE

NGL

ISH

SETUPUP

/TIMEME

T.Z

ONE/D/DSTST

YORKRK

Thank you for purchasing the Canon XH G1S / XH A1S. Please read this manual carefully before you use the camcorder and retain it for future reference. Should your camcorder fail to operate correctly, refer to Troubl es ho ot in g (145).

Conventions Used in this Manual

 : Precautions related to the camcorder’s operation.  : Additional topics that complement the basic operating procedures.  : Reference page number.  Capital letters are used to refer to buttons on the camcorder or the wireless controller.  Brackets [ ] and capital letters are used to refer to menu options as they are displayed on screen.

In tables in the manual, menu options in boldface indicate the default setting.

 “Screen” refers to the LCD screen and the viewfinder screen.  “Card” or “Memory card” refers to an SDHC memory card, an SD memory card or a MultiMedia Card

(MMC).

 Photographs in the manual are simulated pictures taken with a still camera.  : Text that applies only to the model shown in the icon.  Illustrations in the manual show

the XH G1S.

Operating modes

The availability of the various functions depends on the operating mode as indicated in the bar.

, : Function can be used in this mode.

, : Function cannot be used in this mode.

Menu item shown at its default position

Language and Date/Time Settings

Changing the Display Language

The default language for displays and menu items is English. The language can be changed to German, Spanish, French, Italian, Polish, Russian, simplified Chinese or Japanese.

DIDISPSPLAY

(27)

To change the display language, open the menu and select [DISPLAY SETUP/ ]. Select [LANGUAGE ], select a language and close the menu.

If you have mistakenly changed the language, follow the mark next to the menu item to change the setting. The displays and at the bottom of the screen refer to the names of buttons on the camcorder and will not change regardless of the language selected.

Setting the Time Zone/Daylight Saving Time

Set the time zone, date and time when you first start using your camcorder, or if the built-in rechargeable battery has discharged completely.

SYSYSTSTEMEMSET

/ D/TI

LANG

•••

T T.Z

ENGL

ISH

ONE

•••••NEWEW YO

COPY

Trademark Acknowledgements

• Canon is a registered trademark of Canon Inc.

• is a trademark.

• HDV and the HDV logo are trademarks of Sony Corporation and Victor Company of Japan, Ltd. (JVC).

• is a trademark.

• Other names and products not mentioned above may be trademarks or registered trademarks of their respective companies.

• ANY USE OF THIS PRODUCT OTHER THAN CONSUMER PERSONAL USE IN ANY MANNER THAT COMPLIES WITH THE MPEG-2 STANDAR FOR ENCODING VIDEO INFORMATION FOR PACKAGED MEDIA IS EXPRESSLY PROHIBITED WITHOUT A LICENSE UNDER APPLICABLE PATENTS IN THE MPEG-2 PATENT PORTFOLIO, WHICH LICENSE IS AVAILABLE FROM MPEG LA, L.L.C., 250 STEELE STREET, SUITE 300, DENVER, COLORADO 80206.

About the HD/HDV and SD/DV Specifications

In the manual, a distinction is made between video signal standards (camera section) and recording standards (recorder section). The video signal can be set to HD (high definition) or SD (standard definition) specifications; the recording standard on the tape will be HDV or DV, respectively.

Camera Section HD/SD

Recorder Section HDV/DV

Playback Signal HDV/DV

HD/SD SDI Terminal HD/SD

HDV/DV Terminal HDV/D

( only)

Introduction

COPY

Introduction

The XH G1S / XH A1S - A Broad Range of Capabilities ................................................................................... 5

About this Manual .............................................................................................................................................6

Checking the Supplied Accessories................................................................................................................ 10

Components Guide ......................................................................................................................................... 11

Preparations

Preparing the Power Supply............................................................................................................................ 16

Preparing the Camcorder ................................................................................................................................19

Using the Wireless Controller ..........................................................................................................................24

Loading/Removing a Cassette ........................................................................................................................ 25

Inserting/Removing a Memory Card ............................................................................................................... 26

Changing Settings with the MENU Button ......................................................................................................27

Language and Date/Time Settings .................................................................................................................. 28

Recording

Recording ........................................................................................................................................................ 30

Selecting the Signal Standard and Aspect Ratio ............................................................................................34

Locating the End of the Last Scene ................................................................................................................ 34

Zooming .......................................................................................................................................................... 35

Adjusting the Focus......................................................................................................................................... 37

Using the ND Filter ..........................................................................................................................................41

Selecting the Frame Rate ................................................................................................................................42

Setting the Time Code.....................................................................................................................................44

Synchronizing the Camcorder’s Time Code....................................................................................... 46

Setting the User Bit .........................................................................................................................................48

Audio Recording.............................................................................................................................................. 49

Image Stabilizer ...............................................................................................................................................54

Using the Programmed AE Modes..................................................................................................................55

Recording in Manual Mode .............................................................................................................................58

Recording in Shutter-Priority (Tv) Mode .......................................................................................................... 60

Recording in Aperture-Priority (Av) Mode........................................................................................................ 61

Adjusting the Exposure ................................................................................................................................... 62

AE Shift............................................................................................................................................................ 62

Gain ................................................................................................................................................................. 63

White Balance .................................................................................................................................................65

Zebra Pattern...................................................................................................................................................67

Color Correction .............................................................................................................................................. 68

Skin Detail Function.........................................................................................................................................70

Selective Noise Reduction ..............................................................................................................................71

Clear Scan ....................................................................................................................................................... 72

Custom Keys ................................................................................................................................................... 73

Color Bars/Audio Reference Signal.................................................................................................................77

External Connections

Video Signal Output Standards ....................................................................................................................... 78

Connecting to a Monitor/TV ............................................................................................................................ 79

Audio Output ...................................................................................................................................................83

Digital Video Control........................................................................................................................................ 85

Recording an External Video Signal (HDV/DV In, Analog Line-In)................................................................... 86

Converting Analog Signals into Digital Signals (Analog-Digital Converter) ..................................................... 87

Connecting to a Computer ..............................................................................................................................88

COPY

Customization

Custom Preset Settings .................................................................................................................................. 89

Customized Functions .................................................................................................................................... 97

Customized On-Screen Displays .................................................................................................................. 103

Playback

Playing Back a Tape ...................................................................................................................................... 107

Returning to a Pre-marked Position.............................................................................................................. 109

Index Search ................................................................................................................................................. 109

Date Search................................................................................................................................................... 110

Data Code ..................................................................................................................................................... 110

Remote Sensor Mode ................................................................................................................................... 111

Using a Memory Card

Selecting the Still Image Quality/Size............................................................................................................ 112

File Numbers ................................................................................................................................................. 113

Recording Still Images on a Memory Card ................................................................................................... 114

Reviewing a Still Image Right After Recording.............................................................................................. 116

Drive Mode .................................................................................................................................................... 117

Metering Mode .............................................................................................................................................. 118

Using an Optional Flash ................................................................................................................................ 119

Playing Back Still Images from a Memory Card............................................................................................ 120

Erasing Still images ....................................................................................................................................... 122

Protecting Still images................................................................................................................................... 123

Initializing a Memory Card............................................................................................................................. 124

Print Order Settings....................................................................................................................................... 125

Additional Information

Menu Options and Default Settings .............................................................................................................. 126

Settings Memorized and Retained ................................................................................................................ 135

Screen Displays............................................................................................................................................. 136

List of Messages ........................................................................................................................................... 139

Maintenance/Others...................................................................................................................................... 140

Troubleshooting............................................................................................................................................. 145

System Diagram............................................................................................................................................ 147

Optional Accessories .................................................................................................................................... 148

Specifications................................................................................................................................................ 150

Index.............................................................................................................................................................. 152

Introduction

COPY

Checking the Supplied Accessories

CA-920 Compact Power Adapter DC-920 DC Coupler BP-950G Battery Pack WL-D5000 Wireless Controller

SD Memory Card HDVM-E63PR Digital

DTC-1000 Component Video Cable

Lens Cap Lens Hood Eye Cup

Videocassette

Adjustment Band (for the external microphone holder)

2 x AA (R6) Batteries (for the wireless controller)

Tripod Adapter Base SS-1100 Shoulder Strap

STV-290N Stereo Video Cable

COPY

The serial number of this product can be found at the battery attachment unit of the camcorder. Write down the number and other information here and retain this book as a permanent record of your purchase to aid identification in case of theft. Date of Purchase: Model Name: XH G1S A / XH A1S A Purchased From: Serial No.: Dealer Address Dealer Phone No.:

Components Guide

Left side view

dial

External control mode* VCR/PLAY mode Power off Manual Auto Shutter-Priority Aperture-Priority Spotlight Night Easy Recording

* Reserved mode for future software development.

Recording programs

Introduction

DISP. (display) button ( 33) PEAKING button ( 39) MAGN. (magnification) button ( 39)

(record review) button ( 33) POSITION PRESET switch ( 36, 40) Focus mode switch ( 37) POSITION PRESET ON/SET switch ( 36, 40) ND FILTER switch ( 41) Iris ring ( 58, 61) POWER indicator Side panel ( 138) OPEN (open the LCD display) switch ( 20)

CH1/CH2 dials ( 51) AUDIO LEVEL LOCK switch ( 51) SELECT/SET dial ( 27)/ (volume) dial ( 108)

COPY

MENU button ( 27) Focus ring ( 37) Zoom ring ( 35) SHUTTER dial ( 60)/ dial ( 66) PUSH AF button ( 37) EXP. LOCK button ( 62)/PUSH AE button ( 59) GAIN switch ( 63) AGC (automatic gain control) switch ( 63) OUTPUT switch ( 77) AWB (automatic white balance) switch ( 65) WHITE BAL. (white balance) switch ( 65) WHITE BAL. button ( 65) CUSTOM KEYS ( 73) CUSTOM PRESET ON/OFF button ( 92) CUSTOM PRESET SELECT button ( 92)

Right side view

COPY

ZOOM SPEED switch ( 35)

/ (card/tape) switch ( 114) VIDEO 2 terminal ( 81) HD/SD SDI terminal* ( 79) GENLOCK terminal* ( 46) TIME CODE terminal* ( 46) MIC (external microphone) terminal ( 49)

switches ( 50)

*only.

switches ( 52) Lens hood ( 22) Lens hood locking screw ( 22)

switches ( 51) CH1 input terminal ( 50) CH2 input terminal ( 50) Cassette compartment ( 25) TIME CODE switch* ( 46)

Front view

Back view

Introduction

External microphone holder ( 50) Tally lamp ( 102) External sensor for the Instant AF ( 37) Grip belt ( 22) Attachment sockets for the optional TA-100 Tripod

Adapter ( 148) or the supplied tripod adapter base

Microphone lock screw ( 21) Remote sensor ( 24, 111) Tripod socket Viewfinder ( 19) OPEN (open the battery compartment) switch ( 16) CARD access indicator ( 114) Battery/memory card compartment ( 16)

, Using tripods

Do not use tripods with mounting screws longer than 5.5 mm (0.2 in.) as this may cause damage to the camcorder. To use tripods featuring 3/8" mounting screws, attach first the supplied tripod adapter base and attach the tripod to the adapter base.

About the Terminal

(LANC) stands for Local Application Control Bus System. The terminal allows you to connect and control connected devices. Connect

only devices with the mark to the terminal.

Operation cannot be guaranteed for connections with devices not bearing the mark. Some buttons of connected devices may not operate or may operate differently than the buttons on the camcorder.

COPY

Dioptric adjustment lever ( 19) VIEWFINDER COMPONENT OUT terminal ( 80)

terminal A/V1 terminal ( 79) HDV indicator HDV/DV terminal ( 81, 86, 88)

(headphones) terminal HD/SD COMPONENT OUT terminal ( 80) START/STOP button ( 30) Memory card slot ( 26) Battery attachment unit ( 16) BATT. RELEASE latch ( 16)

Top vi ew

(pause) button ( 107) /

DRIVE MODE button ( 117)

(stop) button ( 107) /

(metering mode) button ( 118)

(rewind) button ( 107) /

– button ( 120)

(play) button ( 107) /

SLIDESHOW button ( 120)

(fast forward) button ( 107) /

+ button ( 120)

REC (record) button ( 86) START/STOP button ( 30) LOCK switch ( 31) OPEN/EJECT switch ( 25) Grip zoom lever ( 35)

COPY

PHOTO button ( 114)/MAGN. button ( 39) Zoom speed adjustment dial ( 35) RESET button Speaker ( 108) MIC ATT. switch ( 51) WHITE BAL. PRESET switch ( 65) END SEARCH button ( 34) Strap mount ( 22) Microphone ( 49) Strap mount ( 22) Hot shoe ( 119) Handle zoom lever ( 35) PHOTO button ( 114)/MAGN. button ( 39) LCD panel ( 20)

WL-D5000 Wireless Controller

Introduction

PHOTO button ( 114) START/STOP button ( 30) MENU button ( 27) TV SCREEN button ( 74) SLIDESHOW button ( 120) DATA CODE button ( 110) INDEX WRITE button ( 74) AUDIO MONITOR button ( 83) END SEARCH button ( 34) SEARCH SELECT button ( 109, 110) REC PAUSE button ( 86) REW button ( 107) ZERO SET MEMORY button ( 109)

button ( 107)

PAUSE button ( 107)

COPY

REMOTE SET button ( 111) AV DV button ( 87) Zoom buttons ( 35) Menu selection buttons ( 27) SET button ( 27) CARD – button ( 120) CARD + button ( 120) MIX BALANCE buttons ( 83)

/ buttons ( 109, 110)

PLAY

button ( 107)

FF button ( 107)

button ( 107)

STOP

button ( 107)

SLOW

button ( 107)

Preparations

Preparing the Power Supply

Charging the Battery Pack

Disconnect the DC coupler from the compact power adapter before charging. Remove the terminal cover of the battery pack.

1. Connect the power cord to the compact power adapter.

2. Plug the power cord into a power outlet.

3. Attach the battery pack to the compact power adapter.

• Press lightly and slide the battery pack in the

direction of the arrow until it clicks.

• The charge indicator starts flashing. The indicator

will stay on when the charging is completed.

4. When the charging is completed, remove the battery pack from the compact power adapter.

5. Unplug the power cord from the power outlet and disconnect it from the compact power adapter.

Attaching the Battery Pack

1. Turn the dial to OFF.

2. Push the OPEN switch in the direction of the arrow to open the battery compartment cover.

3. Insert the battery all the way into the compartment and press gently until it clicks.

4. Close the battery compartment cover.

Charge indicator

To Remove the Battery

1. Turn the dial to OFF.

2. Push the the arrow to open the battery compartment cover.

3. Press the BATT.RELEASE latch left and pull out the battery.

4. Close the battery compartment cover.

OPEN switch in the direction of

COPY

Using a Household Power Outlet

1. Turn the dial to OFF.

2. Attach the DC coupler to the camcorder.

Open the battery compartment cover and slide the DC coupler all the way into the compartment and press gently until it clicks.

3. Connect the power cord to the power adapter.

4. Plug the power cord into a power outlet.

5. Connect the DC coupler to the adapter.

6. Pass the cable through the special slot and close battery compartment cover.

7. Detach the DC coupler after use.

Open the battery compartment cover, press the BATT.RELEASE latch left and pull out the DC coupler.

About the Built-in Rechargeable Lithium Battery

This camcorder has a built-in rechargeable lithium battery to retain the date, time and other settings. The built-in battery is recharged every time you use the camcorder. However, when you use the camcorder for only short periods or do not use it for a period of over 3 months, it will discharge completely. In that case, recharge the built-in battery by powering the camcorder from a power outlet and leaving it with the dial set to OFF for at least 24 hours.

Preparations

 Disconnect the DC coupler from the compact power adapter when charging a battery pack.  Turn off the camcorder before connecting or disconnecting the compact power adapter.  If the compact power adapter is used close to a TV, it may cause picture interference. Move the

compact power adapter away from the TV or the antenna cable.

 Do not connect to the compact power adapter any products not expressly recommended for use

with this camcorder.

 If you connect a faulty compact power adapter or battery pack, the charge indicator turns off and

charging will stop.

 The charge indicator serves also as an indication about the charge status.

0-50%: Flashes once per second 50-75%: Flashes twice per second More than 75%: Flashes 3 times per second 100%: Continuously on

 We recommend charging the battery pack in temperatures between 10 °C and 30 °C (50 °F and

86 °F). The charging time will vary depending on the surrounding temperature and the battery’s initial charge condition.

 In cold places the effective usage time of the battery will decrease.  We recommend that you prepare battery packs 2 to 3 times longer than you think you might need.  To conserve battery power, turn off the camcorder instead of leaving it in record pause mode.  USA and Canada only: The Lithium ion/polymer battery that powers the product is

recyclable. Please call 1-800-8-BATTERY for information on how to recycle this battery.

COPY

 Charging, Recording and Playback Times

The following times are approximate and vary according to the charging, recording and playback conditions.

Battery Pack

Charging Time with the CA-920 Compact Power Adapter

BP-930 BP-945 BP-950G BP-970G

145 min. 220 min. 235 min. 320 min.

Recording and Playback Times

HDV

Maximum Recording Time Viewfinder [NORMAL]

Viewfinder [BRIGHT] LCD screen [NORMAL] LCD screen [BRIGHT]

Typical Recording Time* Viewfinder [NORMAL]

Viewfinder [BRIGHT] LCD screen [NORMAL] LCD screen [BRIGHT]

Playback Time LCD screen [NORMAL]

Recording and Playback Times

Maximum Recording Time Viewfinder [NORMAL]

Viewfinder [BRIGHT] LCD screen [NORMAL] LCD screen [BRIGHT]

Typical Recording Time* Viewfinder [NORMAL]

Viewfinder [BRIGHT] LCD screen [NORMAL] LCD screen [BRIGHT]

Playback Time LCD screen [NORMAL]

Recording and Playback Times

HDV

Maximum Recording Time Viewfinder [NORMAL]

Viewfinder [BRIGHT] LCD screen [NORMAL] LCD screen [BRIGHT]

Typical Recording Time* Viewfinder [NORMAL]

Viewfinder [BRIGHT] LCD screen [NORMAL] LCD screen [BRIGHT]

Playback Time LCD screen [NORMAL]

Recording and Playback Times

Maximum Recording Time Viewfinder [NORMAL]

COPY

Typical Recording Time* Viewfinder [NORMAL]

Playback Time LCD screen [NORMAL]

* Approximate times for recording with repeated operations such as start/stop, zooming, power on/off.

Actual time may be shorter.

Viewfinder [BRIGHT] LCD screen [NORMAL] LCD screen [BRIGHT]

BP-930 BP-945 BP-950G BP-970G

150 min. 220 min. 315 min. 430 min. 145 min. 215 min. 305 min. 430 min. 145 min. 215 min. 305 min. 430 min. 140 min. 210 min. 295 min. 420 min.

90 min. 135 min. 190 min. 260 min. 90 min. 130 min. 185 min. 260 min. 85 min. 130 min. 185 min. 255 min. 85 min. 125 min. 175 min. 245 min.

160 min. 240 min. 335 min. 475 min.

BP-930 BP-945 BP-950G BP-970G

165 min. 245 min. 345 min. 490 min. 160 min. 240 min. 340 min. 485 min. 160 min. 240 min. 335 min. 475 min. 155 min. 230 min. 325 min. 460 min.

95 min. 145 min. 205 min. 295 min. 95 min. 145 min. 205 min. 295 min. 95 min. 140 min. 200 min. 275 min. 90 min. 140 min. 195 min. 280 min.

175 min. 265 min. 370 min. 530 min.

BP-930 BP-945 BP-950G BP-970G

155 min. 230 min. 325 min. 465 min. 155 min. 230 min. 325 min. 460 min. 150 min. 225 min. 315 min. 445 min. 145 min. 215 min. 305 min. 430 min.

95 min. 140 min. 200 min. 285 min. 95 min. 140 min. 200 min. 285 min. 90 min. 140 min. 195 min. 275 min. 90 min. 135 min. 190 min. 260 min.

165 min. 250 min. 350 min. 505 min.

BP-930 BP-945 BP-950G BP-970G

170 min. 255 min. 360 min. 515 min. 170 min. 255 min. 355 min. 510 min. 165 min. 245 min. 350 min. 495 min. 160 min. 240 min. 335 min. 485 min. 105 min. 155 min. 225 min. 315 min. 105 min. 155 min. 220 min. 315 min. 100 min. 150 min. 215 min. 305 min.

95 min. 145 min. 205 min. 295 min.

185 min. 275 min. 390 min. 565 min.

Preparing the Camcorder

Attaching and Detaching the Eye Cup

Attaching the Eye Cup

Attach the eye cup so that it covers the rubber portion of viewfinder unit.

• The dioptric adjustment lever can be operated even with the eye cup attached.

• For left eye use, attach the eye cup so that the protruding portion faces the opposite side.

Viewfinder unit

Detaching the Eye Cup

Detach the eye cup as shown in the illustration.

Preparations

Dioptric Adjustment

Turn on the camcorder and adjust the dioptric adjustment lever.

COPY

Do not let the viewfinder be exposed to direct sunlight or other strong light sources. The viewfinder LCD may become damaged due to concentration of the light by the lens. Pay special attention when mounting the camcorder on a tripod, or during its transportation.

Using the LCD Display

1. Slide the OPEN switch in the direction of the arrow to unlock the LCD panel.

2. Pull out the LCD panel.

3. Rotate the LCD panel and adjust it to the desired position.

 You can change the LCD display to black & white ( 21).  By default, the viewfinder display is turned off while you use the LCD panel. However, you can

change the settings to be able to use both displays simultaneously ( 21).

Adjusting the Viewfinder/LCD Display

You can adjust the brightness, contrast, color, sharpness and backlight* of the viewfinder/LCD display. These adjustments will not affect your recording.

* The default value is [BRIGHT] while using the power adapter.

(27)

1. Press the MENU button.

2. Turn the SELECT/SET dial to select [DISPLAY SETUP/ ] and press the dial.

3. Select [CVF SETUP] (to adjust the viewfinder) or [LCD SETUP] (to adjust the LCD

4. Adjust the setting with the SELECT/SET dial and press the dial.

5. Press the MENU button to close the menu.

DISPLAY SETUP/ CVF SETUP BRIGHTNESS•••0

LCD SETUP CONTRAST•••••0

COLOR••••••••0

SHARPNESS••••2

BACKLIGHT••••NORMAL

display), and then select [BRIGHTNESS], [CONTRAST], [COLOR], [SHARPNESS] or [BACKLIGHT].

COPY

After the adjustment you will return to the previous submenu. Change additional settings in the same way as necessary.

Using the Viewfinder and the LCD Display Simultaneously

By default, the viewfinder display is turned off while you use the LCD display. Follow the procedure below to use both of them simultaneously.

(27)

1. Press the MENU button.

2. Turn the SELECT/SET dial to select [DISPLAY SETUP/ ] and press the dial.

3. Select [CVF+LCD ON], set it to [ON] and press the dial.

4. Press the MENU button to close the menu.

Changing the Viewfinder and the LCD Display to Black & White Display

The LCD display and the viewfinder are both color displays. Follow the procedure below to turn both of them to black & white display mode.

(27)

1. Press the MENU button.

2. Turn the SELECT/SET dial to select [DISPLAY SETUP/ ] and press the dial.

3. Select [CVF+LCD BW], set it to [ON] and press the dial.

4. Press the MENU button to close the menu.

Attaching an External Microphone

1. Loosen the microphone lock screw on the

2. Tighten the lock screw.

3. Plug the microphone cable to the

DISPLAY SETUP/ CVF+LCD ON•••OFF

DISPLAY SETUP/ CVF+LCD BW•••OFF

viewfinder unit, open the microphone holder and insert the microphone.

camcorder’s XLR terminal or MIC terminal.

Preparations

COPY

 The microphone must have a diameter of 25 mm or less.  To use an external microphone with a diameter too small for the microphone holder to close

securely, attach first the supplied adjustment band to the microphone holder and then insert the microphone.

MIC terminal

Fastening the Grip Belt

Adjust the grip belt so that you can reach the zoom lever with your index and middle finger, and the START/STOP button with your thumb.

Attaching the Shoulder Strap

Pass the ends through the strap mount and adjust the length of the strap.

Be careful not to drop the camcorder when adjusting the strap or the grip belt.

Attaching the Lens Hood

Attach the lens hood to protect the lens and shade it from stray light.

1. Place the lens hood on the front of the lens so that the window for the external Instant AF sensor faces down and turn it 90 degrees clockwise.

• Be careful not to deform the lens hood.

• Make sure that the lens hood is aligned with the

thread.

2. Tighten the locking screw.

COPY

Window for Instant AF sensor

Opening and Closing the Terminal Covers

Open the covers for the following terminals in order to access them.

HD/SD SDI terminal* GENLOCK terminal* TIME CODE terminal* VIEWFINDER COMPONENT OUT terminal

* only.

Opening the Terminal Covers

1. Open the terminal cover and pull it out.

2. Grasp the strip connecting the cover to the camcorder and pull.

This step is not necessary for the HD/SD SDI terminal and VIDEO 2 terminal.

Closing the Terminal Covers

Insert into the opening the strip connecting the cover to the camcorder and close the terminal.

HD/SD COMPONENT OUT terminal A/V1 and terminals HDV/DV and (headphones) terminals VIDEO 2 terminal

Preparations

If the connecting strip is difficult to grasp, use a pair of tweezers or similar tool.

COPY

Using the Wireless Controller

When you press the buttons on the wireless controller, point it at the camcorder’s remote sensor.

Inserting the Batteries

The wireless controller operates with two AA (R6) batteries.

1. Open the battery cover.

2. Insert the batteries following the + and – markings.

3. Close the battery cover.

 The camcorder and wireless controller are equipped with 2 remote sensor modes ( 111). If the

wireless controller does not work, verify that the camcorder and wireless controller are set to the same mode.

 When the camcorder cannot be operated with the wireless controller, or when it can only be

operated at very close range, replace the batteries. Make sure to replace both batteries at the

same time.

 The wireless controller may not work properly when the remote sensor is located under strong

light sources or direct sunlight.

COPY

Loading/Removing a Cassette

Use only videocassettes marked with the logo. For recording in HDV we recommend you use videocassettes designed for HDV recording.

1. Slide the OPEN/EJECT switch to open the cassette compartment cover.

The cassette compartment opens automatically.

2. Load/remove the cassette.

• Insert the cassette straight, fully into the

compartment with the window facing out.

• Remove the cassette by pulling it straight out.

Preparations

3. Close the cassette compartment by pressing on the mark on the cover.

The cassette compartment will retract automatically.

4. Close the cassette compartment cover.

COPY

 Do not interfere with the cassette compartment while it is opening or closing automatically.  Be careful not to get your fingers caught in the cassette compartment.

If the camcorder is connected to a power source, cassettes can be loaded/removed even if the

dial is set to OFF.

Inserting/Removing a Memory Card

You can use only SDHC (SD High Capacity) memory cards, SD memory cards or MultiMedia Cards (MMC) with this camcorder.

Inserting the Card

1. Set the dial to OFF.

2. Push the OPEN switch in the direction of the arrow to open the battery/memory card compartment cover.

3. Insert the memory card straight, all the way into the memory card slot.

4. Close the compartment.

Do not force the cover closed if the card is not correctly inserted.

Removing the Card

Do not forcefully remove the memory card without first pushing it in to release it.

1. Make sure that the CARD access indicator is not flashing and set the dial to OFF.

2. Push the OPEN switch in the direction of the arrow to open the battery/memory card compartment cover.

3. Push the memory card once to release it and then remove the memory card.

4. Close the compartment.

 If you use memory cards other than the supplied one, make sure to initialize them with the

camcorder ( 124).

 Turn off the camcorder before inserting or removing the memory card. Inserting/removing the

memory card with the camcorder on may result in permanent data loss.

 SDHC and SD memory cards have a write-protect switch to prevent their accidental erasure.

When this switch is set to the LOCK position, images cannot be recorded on or deleted from the memory card.

 Proper operation cannot be guaranteed for all memory cards.

COPY

CARD access indicator

Changing Settings with the MENU Button

Many of the camcorder’s functions can be changed from the on-screen menu.

Selecting Menus and Settings

1. Press the MENU button to open the menu.

2. Turn the SELECT/SET dial to select a submenu and press the dial.

3. Turn the SELECT/SET dial to select a menu item and press the dial.

4. Turn the SELECT/SET dial to select a setting option and press the dial.

5. Press the MENU button to close the menu.

 The , and icons displayed at the bottom of the screen will give you additional

indications about the function of these controls in specific situations.

 You may find it more convenient to use the wireless controller to operate the menu. Press the

MENU button on the wireless controller to open or close the menu. Use the menu selection buttons of the wireless controller instead of the SELECT/SET dial, and press the SET button on the wireless controller to save the settings or make a selection.

 Unavailable items will appear grayed out.  Pressing the MENU button at any time closes the menu.

MENU button

SELECT/SET dial

Preparations

COPY

Language and Date/Time Settings

Changing the Display Language

The default language for displays and menu items is English. The language can be changed to German, Spanish, French, Italian, Polish, Russian, simplified Chinese or Japanese.

(27)

To change the display language, open the menu and select [DISPLAY SETUP/ ]. Select [LANGUAGE ], select a language and close the menu.

Setting the Time Zone/Daylight Saving Time

Set the time zone, date and time when you first start using your camcorder, or if the built-in rechargeable battery has discharged completely.

(27)

1. Press the MENU button.

2. Turn the SELECT/SET dial to select [SYSTEM SETUP/ ] and press the dial.

3. Select [D/TIME SET ] and then select [T.ZONE/DST] and press the dial.

4. Turn the SELECT/SET dial to select the setting option that matches your time zone

DISPLAY SETUP/ LANGUAGE

 If you have mistakenly changed the language, follow the mark next to the menu item to change

the setting.

 The displays and at the bottom of the screen refer to the names of buttons on the

camcorder and will not change regardless of the language selected.

SYSTEM SETUP/ D/TIME SET T.ZONE/DST•••NEW YORK

The time zone setting appears. The default setting is New York.

and press the dial.

To adjust for daylight saving time, select the time zone marked with a .

•••

ENGLISH

Setting the Date and Time

(27)

5. Select [DATE/TIME] and press the dial.

6. Turn the SELECT/SET dial to select the year, and press the dial.

7. Press the MENU button to close the menu and start the clock.

SYSTEM SETUP/ D/TIME SET

The year display starts flashing.

• The month starts flashing.

• Set the rest of the date and time in the same way.

If you do not use the camcorder for a period of approximately 3 months, the built-in rechargeable battery will discharge completely and the date and time settings will be lost. In that case, recharge the built-in battery ( 17) and set the time zone, date and time again.

COPY

DATE/TIME••• JAN.1,2008 12:00 AM

Displaying the Date and Time while Recording

You can display the date and time in the lower left corner of the screen.

(27)

Open the menu and select [DISPLAY SETUP/ ]. Select [GUIDE INFO], set it to [D/T DISPLAY] and close the menu.

Changing the Date Format

You can select between three date formats: [JAN. 1, 2008], [1. JAN. 2008] and [2008. 1. 1].

(27)

Open the menu and select [SYSTEM SETUP/ ]. Select the [D/TIME SET ] submenu and then select [DATE FORMAT]. Select a date format and close the menu.

DISPLAY SETUP/ GUIDE INFO•••OFF

SYSTEM SETUP/ D/TIME SET DATE FORMAT

••

JAN. 1,2008

Preparations

COPY

Recording

Before You Begin Recording

Make a test recording first to check if the camcorder operates correctly. If necessary, clean the video heads ( 143).

The default recording standard is HDV. About the audio recording, refer to the relevant chapter ( 49).

Recording

1. Remove the lens cap.

2. Move the / (card/tape) switch to .

3. Press the lock button and set the

dial to a recording program.

4. Press the START/STOP button to begin recording.

• The tally lamp lights up and the recording

indicator appears on the screen.

• Press the START/STOP button again to pause

recording.

/ switch

Tally lamp

When You Have Finished Recording

1. Set the dial to OFF.

2. Replace the lens cap.

3. Remove the cassette.

4. Disconnect the power source.

The end search, date search and index search functions may not work correctly if you mix recordings in HDV and DV standards on the same tape. We recommend not mixing recordings in different standards on the same tape.

 After inserting a cassette, wait until the tape counter stops completely before you start recording.  Turn the dial to OFF if you do not intend to use the camcorder for a long time.  If you do not remove the cassette, you can record the next scene without any noise or blank

sections between recordings even if you turn the camcorder off.

COPY

+ 125 hidden pages

Canon XH G1S, XH A1S Instruction Manual

Introduction

Important Usage Instructions

IMPORTANT SAFETY INSTRUCTIONS

The XH G1S / XH A1S - A Broad Range of Capabilities

About this Manual

Contents

Checking the Supplied Accessories

Components Guide

Preparations

Preparing the Power Supply

Preparing the Camcorder

Using the Wireless Controller

Loading/Removing a Cassette

Inserting/Removing a Memory Card

Changing Settings with the MENU Button

Language and Date/Time Settings

Recording

Recording