MIC Series 400 Camera | 3
18x Optical Zoom Module
Lens F=4.1 mm (wide) to 73.8 mm (tele), F1.4 to
F3.0
Zoom 18x optical (12x digital)
Angle of view 48° (wide) to 2.8° (tele)
Minimum illumination 0.7 lux (F1.4, 1/60s NTSC, 1/50s PAL)
0.11 lux (F1.4, 1/4s NTSC, 1/3s PAL)
0.01 lux (F1.4, 1/4s NTSC, 1/3s PAL ICR on)
Shutter speed 1/1 to 1/10,000 s (22 steps) NTSC, PAL
36x Optical Zoom Module
Lens F=3.4 mm (wide) to 122.4 mm (tele), F1.6 to
F4.5
Zoom 36x optical (12x digital)
Angle of view 57.8° (wide) to 1.7° (tele)
Minimum illumination 1.4 lux (1/60 s NTSC, 1/50 s PAL, typical,
F1.6, 50IRE);
0.1 lux (1/4 s NTSC, 1/3 s PAL, typical, F1.6,
50IRE)
ICR-ON mode: 0.01 lux (1/4 s NTSC, 1/3 s
PAL)
Shutter speed 1/4 to 1/10,000 s (20 steps) NTSC, 1/3 to
1/10,000 s (20 steps) PAL
Operational
Auto flip Yes
Manual flip Yes
Dynamic privacy zones 3D privacy masking with infinite zones, (some
models, see ordering guide)
Presets 64 telemetry presets utilizing resolver technol-
ogy (using FV protocol, 10 camera set-up presets to allow ANPR, color correction etc.)
Preset tours 6 tours each with up to 32 presets
Sector titles Yes (64 sectors) 20 characters per title
Preset titles 20 character caption for each of the 64 pre-
sets
Home position Yes (preset 1 or tour)
Communication and Protocols
Communication RS485 / RS422
Control protocol Bosch or FV protocol cameras available, addi-
tional supported protocols are Pelco D, Kalatel, 360 Vision, American Dynamics, Panasonic, Molynx, VCL, and Vicon.
These can be loaded using the MICUSB485CVTR signal converter and Cam-set
via a PC.
Biphase control requires a Biphase to RS485
converter (MIC-BP4, available separately) to
connect to Bi-phase equipment.
Connectivity
Video Co-axial via composite cable
Telemetry control card Built-in
Telemetry Twisted pair. Simplex, half and full duplex op-
eration via composite cable
MIC Universal Camera
Setup Software Utility
(Cam-set)
Supplied with each camera, Cam-set allows direct connection to a USB equipped PC via the
MIC Series PSU or over a full duplex or IP network to provide access to all camera functions
and useful diagnostic tools.
USB to RS485 signal converter
Allows MIC Series cameras to connect to a PC
(supplied free with MIC Series 400 camera or
available separately).
Power Via composite cable
Alarms
Alarm inputs 1 tamper input (additional inputs possible with
optional alarm card in PSU)
Alarm communication Tamper switch (ground connection)
Mechanical
Drive unit Brushless, integral pan/tilt motor drive
Pan angle 360° continuous rotation
Pan speed 6° to 90° per second (variable)
Tilt angle 270°
Tilt speed 0.2° to 90° per second (variable)
Speed control Closed loop electronics
Preset accuracy ±0.56° (typical)
Proportional Pan/Tilt to
Zoom
Yes
Construction
Construction material Machined aluminum
Viewing window Tempered flat glass
Window wiper Standard, long-life silicone wiper
Heater Standard
Standard colors Black( RAL9005), Gray (RAL7001) or White
(RAL9003)
Standard finish Alodine 5200 surface treatment with powder
coat paint
Dimensions (WxHxD) 205 x 360 x 165 mm
(8.07 x 14.17 x 6.50 in.)
(upright and inverted)
Weight 5.5 kg (12 lb) including 4-in. pitch circle diam-
eter (PCD) base
Configurations available Upright mount or upright canted at 45° mount.
(Inverted mount is possible using software setting and upright camera.)
Environmental
Operational temperature -40 °C to +50 °C (-40 °F to +122 °F)
Weather proofing IP68
MTBF 73,817 hours
www.boschsecurity.com