Bosch GSR 7,2-2, GSR 9,6-2, GSR 12-2, GSR 14,4-2, GSR 18-2 User Manual

OBJ_BUCH-593-004.book Page 1 Monday, December 12, 2016 2:41 PM

Robert Bosch Power Tools GmbH

70538 Stuttgart

GERMANY

www.bosch-pt.com

GSR Professional

7,2-2 | 9,6-2 | 12-2 | 14,4-2 | 18-2

1 609 92A 2VM (2016.11) AS / 40 ASIA

en Original instructions cn tw

ko

th id Petunjuk-Petunjuk untuk

Penggunaan Orisinal

vi Bản gốc hướng dẫn sử dụng

OBJ_BUCH-593-004.book Page 2 Monday, December 12, 2016 2:41 PM

2 |

English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 5

. . . . . . . . . . . . . . . . . . . . . . 10

. . . . . . . . . . . . . . . . . . . . . . 14

. . . . . . . . . . . . . . . . . . . . . . . .

18

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Bahasa Indonesia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Halaman 28

Tiếng Việt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Trang 33

	1 609 92A 2VM | (12.12.16)				Bosch Power Tools

OBJ_BUCH-593-004.book Page 3 Monday, December 12, 2016 2:41 PM

| 3

5

1

4

3

2

10

9

8

7 6

11

GSR 18-2

	Bosch Power Tools				1 609 92A 2VM | (12.12.16)

OBJ_BUCH-593-004.book Page 4 Monday, December 12, 2016 2:41 PM

4 |

A	B
	8

12
8
	13
C	D
14	14
E
9
	9
1 609 92A 2VM | (12.12.16)	Bosch Power Tools

OBJ_BUCH-593-004.book Page 5 Monday, December 12, 2016 2:41 PM

English

Safety Notes

General Power Tool Safety Warnings

WARNING Read all safety warnings and all instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mainsoperated (corded) power tool or battery-operated (cordless) power tool.

Work area safety

Keep work area clean and well lit. Cluttered or dark areas invite accidents.

Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

Electrical safety

Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.

Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators.

There is an increased risk of electric shock if your body is earthed or grounded.

Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of electric shock.

Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges and moving parts. Damaged or entangled cords increase the risk of electric shock.

When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

Personal safety

Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.

Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection

English | 5

used for appropriate conditions will reduce personal injuries.

Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool.

Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.

Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.

Power tool use and care

Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.

Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.

Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use.

Many accidents are caused by poorly maintained power tools.

Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed.

Use of the power tool for operations different from those intended could result in a hazardous situation.

Battery tool use and care

Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery

	Bosch Power Tools				1 609 92A 2VM | (12.12.16)

OBJ_BUCH-593-004.book Page 6 Monday, December 12, 2016 2:41 PM

6 | English

pack may create a risk of fire when used with another battery pack.

Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.

When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.

Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.

Service

Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

Safety Warnings for Drills and Screwdrivers

Hold power tool by insulated gripping surfaces when performing an operation where the cutting accessory or fastener may contact hidden wiring. Cutting accessory and fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.

Use appropriate detectors to determine if utility lines are hidden in the work area or call the local utility company for assistance. Contact with electric lines can lead to fire and electric shock. Damaging a gas line can lead to explosion. Penetrating a water line causes property damage.

Switch off the power tool immediately when the tool insert jams. Be prepared for high reaction torque that can cause kickback. The tool insert jams when:

–the power tool is subject to overload or

–it becomes wedged in the workpiece.

Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.

Hold the machine with a firm grip. High reaction torque can briefly occur while driving in and loosening screws.

Secure the workpiece. A workpiece clamped with clamping devices or in a vice is held more secure than by hand.

Always wait until the machine has come to a complete stop before placing it down. The tool insert can jam and lead to loss of control over the power tool.

Never leave the machine before it has come to a complete stop. Cutting tools that are still running can cause injuries.

Do not open the battery. Danger of short-circuiting.

Protect the battery against heat, e. g., against continuous intense sunlight, fire, water, and moisture. Danger of explosion.

Use only original Bosch batteries with the voltage listed on the nameplate of your power tool. When using other batteries, e. g. imitations, reconditioned batteries or other brands, there is danger of injury as well as property damage through exploding batteries.

Product Description and Specifications

Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Intended Use

The machine is intended for driving in and loosening screws as well as for drilling in wood, metal, ceramic and plastic.

Product Features

The numbering of the product features refers to the illustration of the machine on the graphics page.

1 Keyless chuck

2 Front sleeve

3 Rear sleeve

4 Torque preselection ring

5Gear selector 7 Battery pack *

6 Battery unlocking button

8 Screwdriver bit *

9 Rotational direction switch

5On/Off switch

8 Handle (insulated gripping surface)

12Universal bit holder *

13Securing screw for keyless chuck

14Hex key **

*Accessories shown or described are not part of the standard delivery scope of the product. A complete overview of accessories can be found in our accessories program.

**Commercially available (not included in the delivery scope)

Technical Data

		Cordless Drill/Driver		GSR ...		7,2-2			9,6-2	12-2		14,4-2	18-2
				Professional
		Article number		3 601 ...			J18 N..		J18 L..	J18 J..		J18 G..	J18 3..
		Rated voltage			V=	7.2			9.6	12		14.4	18
		Please observe the article number on the type plate of your machine. The trade names of the individual machines may vary.
		1 609 92A 2VM | (12.12.16)										Bosch Power Tools

OBJ_BUCH-593-004.book Page 7 Monday, December 12, 2016 2:41 PM

						English | 7
Cordless Drill/Driver	GSR ...	7,2-2	9,6-2	12-2	14,4-2	18-2
	Professional
No-load speed	min-1	0 – 400	0 – 400	0 – 400	0 – 400	0 – 400
– 1st gear
– 2nd gear	min-1	0 – 1 000	0 – 1 000	0 – 1 200	0 – 1 400	0 – 1 250
Max. torque for hard/soft screwdriving	Nm	21 / 9	25 / 10	27 / 11	30 / 15	45 / 22
application according to ISO 5393
Maximum drilling diameter (1st/2nd gear)
– Steel	mm	10 / 10	10 / 10	12 / 12	12 / 12	12 / 12
– Wood	mm	17 / 12	20 / 13	23 / 14	26 / 19	29 / 22
Max. screw dia.	mm	6	6	7	8	8
Chuck clamping range	mm	1 – 10	1 – 10	1 – 10	1 – 10	1 – 10
Drill spindle thread		3/8"	3/8"	3/8"	3/8"	3/8"
Weight according to EPTA-Procedure
01:2014	kg	1.4	1.7	1.5 – 1.6	1.8	2.0

Please observe the article number on the type plate of your machine. The trade names of the individual machines may vary.

Assembly

Battery Charging

A battery that is new or has not been used for a longer period does not develop its full capacity until after approx. 5 charging/discharging cycles.

To remove the battery 7 press the unlocking buttons 6 and pull out the battery downwards. Do not exert any force.

The battery is equipped with a NTC temperature control which allows charging only within a temperature range of between 0 ° C and 45 ° C. A long battery service life is achieved in this manner.

A significantly reduced working period after charging indicates that the battery is used and must be replaced.

Observe the notes for disposal.

Changing the Tool (see figure A)

Before any work on the machine (e. g., maintenance, tool change, etc.) as well as during transport and storage, set the rotational direction switch to the centre position. Unintentional actuation of the On/Off switch can lead to injuries.

Hold the rear sleeve 3 of the keyless chuck 1 tight and turn the front sleeve 2 in rotation direction , until the tool can be inserted. Insert the tool.

Hold the rear sleeve 3 of the keyless chuck 1 tight and firmly turn the front sleeve 2 in rotation direction by hand.

The locking is released again to remove the tool when the front sleeve 2 is turned in the opposite direction.

Replacing the Drill Chuck

Before any work on the machine (e. g., maintenance, tool change, etc.) as well as during transport and storage, set the rotational direction switch to the centre position. Unintentional actuation of the On/Off switch can lead to injuries.

Removing the Securing Screw (see figure B)

The keyless chuck 1 is secured with a securing screw 13 against unintentional loosening from the drill spindle. Completely open the keyless chuck 1 and unscrew the securing screw 13 in rotation direction . Please note that the securing screw has a left-hand thread.

Removing the Drill Chuck (see figure C)

Clamp the short end of a hex key 14 into the keyless chuck 1.

Place the machine on a stable surface (e. g. a workbench). Hold the machine firmly and loosen the keyless chuck 1 by turning the hex key 14 in rotation direction . Loosen a tightseated keyless chuck by giving the long end of the hex key 14 a light blow. Remove the hex key from the keyless chuck and completely unscrew the keyless chuck.

Mounting the Drill Chuck (see figure D)

The keyless chuck is mounted in reverse order.

The drill chuck must be tightened with a tightening torque of approx. 17 – 22 Nm.

Screw the securing screw 13 in anti-clockwise direction into the opened keyless chuck. Always use a new securing screw, as the threads are covered with a thread-locking compound that loses its effect after multiple usage.

Dust/Chip Extraction

Dust from materials such as lead-containing coatings, some wood types, minerals and metal can be harmful to one’s health. Touching or breathing-in the dust can cause allergic reactions and/or lead to respiratory infections of the user or bystanders.

Certain dust, such as oak or beech dust, is considered carcinogenic, especially in connection with wood-treatment additives (chromate, wood preservative). Materials containing asbestos may only be worked by specialists.

–Provide for good ventilation of the working place.

–It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the materials to be worked.

	Bosch Power Tools				1 609 92A 2VM | (12.12.16)

OBJ_BUCH-593-004.book Page 8 Monday, December 12, 2016 2:41 PM

8 | English

Prevent dust accumulation at the workplace. Dust can easily ignite.

Operation

Starting Operation

Inserting the battery

Use only original Bosch O-pack batteries with the voltage given on the type plate of your machine. The use of other batteries can lead to injuries and danger of fire.

Set the rotational direction switch 9 to the centre position in order to avoid unintentional starting. Insert the charged battery 7 into the handle so that it can be felt to engage and faces flush against the handle.

Reversing the rotational direction (see figure E)

The rotational direction switch 9 is used to reverse the rotational direction of the machine. However, this is not possible with the On/Off switch 5 actuated.

Right Rotation: For drilling and driving in screws, push the rotational direction switch 9 left to the stop.

Left Rotation: For loosening or unscrewing screws, push the rotational direction switch 9 right to the stop.

Setting the torque

With the torque presetting ring 4 the required torque setting can be preselected in 25+1 steps. With the correct setting, the insert tool is stopped as soon as the screw is screwed flush into the material or when the adjusted torque is reached. The safety clutch is deactivated in the “ ” position, e. g. for drilling.

Select a higher setting or switch to the “ ” symbol when unscrewing screws.

Gear selection, mechanical

Actuate the gear selector 5 only when the machine is at a standstill.

Two speed ranges can be preselected with the gear selector

5.

Gear I:

Low speed range; for screwdriving or working with large drilling diameter.

Gear II:

High speed range; for working with small drilling diameter.

If the gear selector 5 cannot be pushed through to the stop, lightly turn the drill chuck with drill bit.

Switching On and Off

To start the machine, press the On/Off switch 5 and keep it pressed.

To switch off the machine, release the On/Off switch 5.

Adjusting the Speed

The speed of the switched-on power tool can be variably adjusted, depending on how far the On/Off switch 5 is pressed.

Light pressure on the On/Off switch 5 results in a low rotational speed. Further pressure on the switch results in an increase in speed.

Run-on Brake

When the On/Off switch 5 is released, the chuck brakes to a stop, thus preventing the run-on of the tool.

When driving in screws, wait until the screw is screwed in flush with the material and then release the On/Off switch 5. By doing so, the head of the screw does not penetrate into the material.

Working Advice

Apply the power tool to the screw only when it is switched off. Rotating tool inserts can slip off.

Tips

After longer periods of working at low speed, allow the machine to cool down by running it for approx. 3 minutes at maximum speed with no load.

For drilling in metal, use only perfectly sharpened HSS drill bits (HSS = high-speed steel). The appropriate quality is guaranteed by the Bosch accessories program.

Before screwing larger, longer screws into hard materials, it is advisable to predrill a pilot hole with the core diameter of the thread to approx. 2/3 of the screw length.

Maintenance and Service

Maintenance and Cleaning

Before any work on the machine (e. g., maintenance, tool change, etc.) as well as during transport and storage, set the rotational direction switch to the centre position. Unintentional actuation of the On/Off switch can lead to injuries.

For safe and proper working, always keep the machine and ventilation slots clean.

If the machine should fail despite the care taken in manufacturing and testing procedures, repair should be carried out by an after-sales service centre for Bosch power tools.

In all correspondence and spare parts order, please always include the 10-digit article number given on the type plate of the machine.

After-sales Service and Application Service

Our after-sales service responds to your questions concerning maintenance and repair of your product as well as spare parts. Exploded views and information on spare parts can also be found under:

www.bosch-pt.com

Bosch’s application service team will gladly answer questions concerning our products and their accessories.

	1 609 92A 2VM | (12.12.16)				Bosch Power Tools

OBJ_BUCH-593-004.book Page 9 Monday, December 12, 2016 2:41 PM

English | 9

People’s Republic of China China Mainland

Bosch Power Tools (China) Co., Ltd. 567, Bin Kang Road

Bin Jiang District 310052 Hangzhou, P. R. China

Service Hotline: [phone] Fax: [phone]

E-Mail: [e-mail] www.bosch-pt.com.cn

HK and Macau Special Administrative Regions

Robert Bosch Hong Kong Co. Ltd. 21st Floor, 625 King’s Road North Point, Hong Kong

Customer Service Hotline: [phone] Fax: [phone]

E-Mail: [e-mail] www.bosch-pt.com.hk

Indonesia

PT Robert Bosch Palma Tower 10th Floor

Jl. RA Kartini II-S Kaveling 6 Sek II Pondok Pinang, Kebayoran Lama Jakarta Selatan 12310 Indonesia

Tel.: [phone]

Fax: [phone]

E-Mail: [e-mail] www.bosch-pt.co.id

Philippines

Robert Bosch, Inc.

28th Floor Fort Legend Towers, 3rd Avenue corner 31st Street, Fort Bonifacio Global City, 1634 Taguig City, Philippines Tel.: [phone]

Fax: [phone] [e-mail] www.bosch-pt.com.ph

Bosch Service Center: 9725-27 Kamagong Street San Antonio Village

Makati City, Philippines Tel.: [phone] Fax: [phone]

[e-mail]

Malaysia

Robert Bosch (S.E.A.) Sdn. Bhd. No. 8A, Jalan 13/6

G.P.O. Box 10818 46200 Petaling Jaya Selangor, Malaysia Tel.: [phone] Fax: [phone]

[e-mail] Toll-Free: 1800 880188 www.bosch-pt.com.my

Thailand

Robert Bosch Ltd. Liberty Square Building No. 287, 11 Floor Silom Road, Bangrak Bangkok 10500

Tel.: [phone]

Fax: [phone]

Robert Bosch Ltd., P. O. Box 2054 Bangkok 10501, Thailand www.bosch.co.th

Bosch Service – Training Centre

La Salle Tower Ground Floor Unit No.2

10/11 La Salle Moo 16

Srinakharin Road

Bangkaew, Bang Plee

Samutprakarn 10540

Thailand

Tel.: [phone]

Fax: [phone]

Singapore

Robert Bosch (SEA) Pte. Ltd. 11 Bishan Street 21 Singapore 573943

Tel.: [phone]

Fax: [phone] [e-mail] Toll-Free: 1800 3338333 www.bosch-pt.com.sg

Vietnam

Robert Bosch Vietnam Co. Ltd 13th Floor , 194 Golden Building 473 Dien Bien Phu Street

Ward 25, Binh Thanh District 84 Ho Chi Minh City

Vietnam

Tel.: [phone]

Fax: [phone] Hotline: [phone]

E-Mail: [e-mail] www.bosch-pt.com.vn www.baohanhbosch-pt.com.vn

	Bosch Power Tools				1 609 92A 2VM | (12.12.16)

OBJ_BUCH-593-004.book Page 10 Monday, December 12, 2016 2:41 PM

10 |

Australia, New Zealand and Pacific Islands

Robert Bosch Australia Pty. Ltd. Power Tools

Locked Bag 66

Clayton South VIC 3169

Customer Contact Center Inside Australia:

Phone: [phone] Fax: [phone] Inside New Zealand: Phone: [phone] Fax: [phone] Outside AU and NZ: Phone: [phone] www.bosch-pt.com.au www.bosch-pt.co.nz

Egypt

Unimar

20 Markaz kadmat

El tagmoa EL Aoul – New Cairo

Tel: [phone] - 95 / + 2 02 224 78072 - 73 Fax:[phone]

E-Mail: [e-mail]

Ethiopia

Forever plc

Kebele 2,754, BP 4806, Addis Ababa , Ethiopia

Tel: [phone] E-Mail: [e-mail]

Nigeria

C. Woermann Ltd. P.O. Box 318

6, Badejo Kalesanwo Street Matori Industrial Estate Lagos, Nigeria

Tel: [phone] E-Mail: [e-mail]

Republic of South Africa

Customer service

Hotline: [phone]

Gauteng – BSC Service Centre

35 Roper Street, New Centre Johannesburg

Tel.: [phone]

Fax: [phone] E-Mail: [e-mail]

KZN – BSC Service Centre

Unit E, Almar Centre

143 Crompton Street Pinetown

Tel.: [phone]

Fax: [phone]

E-Mail: [e-mail]

Western Cape – BSC Service Centre

Democracy Way, Prosperity Park

Milnerton

Tel.: [phone]

Fax: [phone]

E-Mail: [e-mail]

Bosch Headquarters

Midrand, Gauteng

Tel.: [phone]

Fax: [phone]

E-Mail: [e-mail]

Disposal

The machine, rechargeable batteries, accessories

and packaging should be sorted for environmentalfriendly recycling.

Do not dispose of power tools and batteries/rechargeable batteries into household waste!

Battery packs/batteries:

Ni-Cd: Nickel cadmium

Warning: These battery packs contain cadmium, a highly toxic heavy metal.

Ni-MH: Nickel metal hydride

Subject to change without notice.

!

" "

 发事故。

 尘或气体。

 中会使操作者失去对工具的控制。

	1 609 92A 2VM | (12.12.16)				Bosch Power Tools

OBJ_BUCH-593-004.book Page 11 Monday, December 12, 2016 2:41 PM

险。

 如果你身体接地会增加电击危险。

 电动工具将增加电击危险。

部件。

 接软线。

 使用剩余电流动作保护器RCD RCD

 瞬间的疏忽会导致严重人身伤害。

| 11

 必须从电源上拔掉插头和/

 是危险的。

 事故由维护不良的电动工具引发。

 刃的刀具不易卡住而且容易控制。

 于那些与其用途不符的操作可能会导致危险。

 盒的充电器用到其他电池盒时会发生着火危险。

/

 遗留在电动工具旋转零件上的扳手或钥匙会导致人 身伤害。

 可能会卷入运动部件中。

 生腐蚀或燃烧。

 性。

 更安全。

 且必须进行修理。

 线会造成火灾並遭受电击。损坏瓦斯管会引起爆 炸。

 被夹住如果

	Bosch Power Tools				1 609 92A 2VM | (12.12.16)

OBJ_BUCH-593-004.book Page 12 Monday, December 12, 2016 2:41 PM

12 |



 现短暂的强大反击。



1

2

3



4

5



7

*

6

8

*



9

5

8

12

*

13

14

**

*

**

/

GSR ...

7,2-2

9,6-2

12-2

14,4-2

18-2

Professional

3 601 ...

J18 N..

J18 L..

J18 J..

J18 G..

J18 3..

=

7,2

9,6

12

14,4

18

0– 400

0– 400

0– 400

0– 400

0– 400

–

/

–

/

0– 1000

0– 1000

0– 1200

0– 1400

0– 1250

ISO 5393 /

21/9

25/10

27/11

30/15

45/22

(1./2. )

–

10/10

10/10

12/12

12/12

12/12

–

17/12

20/13

23/14

26/19

29/22

6

6

7

8

8

1– 10

1– 10

1– 10

1– 10

1– 10

3/8"

3/8"

3/8"

3/8"

3/8"

EPTA-Procedure 01:2014

1,4

1,7

1,5 – 1,6

1,8

2,0

6

7

5 /

1 609 92A 2VM | (12.12.16)

Bosch Power Tools