Bosch ARD-FPBEW2-IC Installation Manual
FPBE W2 Fingerprint Reader
ARD-FPBEW2-IC
en Installation Guide
FPBE W2 Fingerprint Reader
Table of contents
Table of contents | en 3
1
2
2.1 Components 6
2.2 Names and function of parts 8
2.3 Cables and Connectors 10
2.4 How to enroll a fingerprint 13
3
3.1 Fixing the bracket and the product 16
3.2 Power supply connection 20
3.3 Network connection - TCP/IP 21
3.4 Wiegand Connection 22
3.5 RS 485 Connection 23
3.6 Resetting Network Settings 24
4
4.1 Product Specifications 25
4.2 Dimensions 28
Safety 4
Introduction 6
Installation 16
Technical Data 25
Bosch Access Systems GmbH
2018-02 | ARD-FPBEW2-IC |
en | Safety
!
!
4
1
Observe the following instructions to use the product safely and
prevent any risk of injury or property damage.
Safety
FPBE W2 Fingerprint
Warning!
Risk of fire or electric shock
Do not install the product in a place with direct sunlight,
moisture, dust, or soot.
Do not install the product in a place with heat from an
electric heater.
Install the product in a dry place.
Install the product in a place with no electromagnetic
interference.
Do not install or repair the product independently.
Do not allow liquids such as water, beverages, or chemicals
get into the product.
Warning!
Risk of explosion
Replacing the RTC battery with an incorrect type of battery
may cause explosion. Discard the battery according to the
appropriate regional or international waste regulations.
Reader
2018-02 | ARD-FPBEW2-IC |
Notice!
If the product has been damaged due to independent
installation or repair of the product by the user, free A/S
service will not be provided.
Bosch Access Systems GmbH
FPBE W2 Fingerprint Reader
!
Caution!
Product damage or physical injury
Do not install the power supply cable in a place where
people pass by.
Notice!
Risk of product damage or malfunction
Do not install the product near a highly magnetic object
such as a magnet, TV, (especially CRT) monitor, or speaker.
If installing the product outside where the product is
completely exposed, install the product together with the
enclosure.
When installing a number of devices, allow a space between
the devices for installation.
Do not drop the product or apply an impact to the product.
Do not to contaminate or damage the fingerprint contact
unit with a dirty hand or foreign substances.
When cleaning the product, wipe the product with a soft
and dry cloth and no water, benzene or alcohol.
Notice!
For further information on this product
download the Installation Manual and
firmware at our website:
http://www.boschsecurity.com.
Go to Products > Access Control Systems > Readers and
Cards > Biometric readers.
Safety | en 5
Bosch Access Systems GmbH
2018-02 | ARD-FPBEW2-IC |
en | Introduction
6
2
FPBE W2 Fingerprint
Reader
Introduction
2.1
ARD-FPBEW2
Components
Bracket
Ferrite Core
(1 EA)
Heat shrink
Fixing screw (2
EA)
PVC anchor
(2 EA)
Star-shaped
wrench
2018-02 | ARD-FPBEW2-IC |
Bosch Access Systems GmbH
FPBE W2 Fingerprint Reader
Introduction | en 7
OSS Manual
Drilling
template
Notice!
Components may vary according to the installation
environment.
Bosch Access Systems GmbH
Safety
Instructions
2018-02 | ARD-FPBEW2-IC |
Installation
Quick
Guide
en | Introduction
8
FPBE W2 Fingerprint
Reader
2.2
Item Feature
1 LED lamp
2 RF card authentication unit
3 Fingerprint authentication unit
Names and function of parts
Indicates the operational status of the product with the color
of the LED lamp.
Reads RF cards for entering and exiting.
Reads fingerprints placed on it for entering and exiting.
2018-02 | ARD-FPBEW2-IC |
Bosch Access Systems GmbH
FPBE W2 Fingerprint Reader
Item Feature
4 Network reset button
Resets the network configuration. For details, refer to the
Resetting Network Setting.
5 LED lamp for Network
Shows the status of the network connection.
6 Cable
– Interface cable
– Power cable
– Ethernet connector
Introduction | en 9
Bosch Access Systems GmbH
2018-02 | ARD-FPBEW2-IC |
en | Introduction
10
FPBE W2 Fingerprint
Reader
2.3
Cables and Connectors
2018-02 | ARD-FPBEW2-IC |
Bosch Access Systems GmbH
Loading...