Quick Reference
KLN 35A
Bendix/King
®
Global Positioning System
These simplified operating instructions are only to familiarize you with the KLN
35A. For detailed operating instructions, please refer to the KLN 35A Pilot's
Guide P/N 006-08791-0000.
The two concentric knobs and
B
button on the right are used to control the
GPS functions of the
KLN 35A. The right inner knob can be pulled out, but for
now it should be pushed in.
When the cursor is off
, the right outer knob changes the page type (APT to VOR to
NDB, etc.) and the right inner knob changes the page number (APT 1 to APT 2).
When the cursor is on, the right outer knob moves the cursor and the right inner
knob changes the data under the cursor.
To change a cyclic field:
1. Turn on the cursor (by pressing the
B
button) and place it over a cyclic field, which
is always preceded by a carat (>).
2. Press the
E
button to change the cyclic
field. One example is the NAV 1 page, which
can display a D-bar (Figure 1) or numerical
course deviation (Figure 2).
To display the Nearest Airport:
1. Press
G then press F.
2. The waypoint page for the nearest airport will now be displayed on the screen.
The right inner knob (in the “pulled out” position), may be used in the normal
manner to scan the other nearest airports. With the right inner knob in the “in”
position, you may view all four airport pages for a specific airport.
-1-
Figure 1
Figure 2
CRSR
Pull
SCAN
KLN 35A
GPS
GPS
B
PUSH
ON
NRST
89.6nm ∂∆ KOSH
105kt > ««««∫∏π««««
>Leg DTK345° TK347°
NAV 1 >345°To 0:51
APT VOR NDB SUP ACT NAV FPL CAL SET OTH
D
ENTCLRMSG
89.6nm ∂∆ KOSH
105kt > ««««∫∏π««««
>Leg DTK345° TK347°
NAV 1 >345°To 0:51
APT VOR NDB SUP ACT NAV FPL CAL SET OTH
D
ENTCLRMSG
89.6nm ∂∆ KOSH
105kt >Fly L 1.1nm
>Leg DTK345° TK347°
NAV 1 >345°To 0:51
APT VOR NDB SUP ACT NAV FPL CAL SET OTH
D
ENTCLRMSG
DD
To go Direct To a waypoint:
1. Press the
D button. The Direct To (DIR) page will be displayed with a way-
point field.
2. Enter desired waypoint using right concentric knobs.
3. Press
F to view waypoint information. Press F again to confirm.
This initiates the Direct To—your D-bar will be centered, and you’re on your
way!
4. Alternatively, display desired waypoint on APT, VOR, NDB or SUP page, or
move the cursor over desired waypoint in the active flight plan, then press D,
then press
F to confirm.
To initialize the position from the SET 1 page:
1. Press the B button to bring the cursor on the page over the INIT POS: field.
2. Using the right inner and outer knobs, enter the identifier for the airport where
you are presently located or the identifier of a navaid or other airport which is
close to your present position.
3. Once you have entered the complete identifier, press
F. The display will
change to the waypoint page for the waypoint you entered.
4. If this is the waypoint you intended to enter, press F again. The display will
change back to the SET 1 page.
NOTE: As an alternative, you can also enter the approximate latitude and longi-
tude of your present position directly on the SET 1 page instead of entering a
waypoint.
5. With the right inner knob, position the cursor over Ok?, if it is not already there,
and press
F.
-2-
NAV 4 (Moving Map) Page Tips
To change the map scale factor:
1. Press the
B button. The cursor comes up over the map scale in the
lower left corner of the map display.
2. Use the right inner knob to change between scale factors (figure 3).
3. For terminal area operations select AUTO scale factor.
To change what information is displayed on the map:
1. Press the
B button, select Menu? and press the F button to bring up a
pop-up menu (figure 4).
• Line 1: Display 5 nearest special use airspaces (SUAs), on or off
• Line 2: Display 9 nearest VORs; on or off
• Line 3: Display 9 nearest airports; on or off
• Line 4: Map orientation; N↑=North up, DTK↑=Desired track up, TK↑ =
Actual track up (when groundspeed > 2 kts)
2. Use the right outer knob to select the desired item, and the right inner knob
to change the setting.
-3-
Figure 3
Figure 4
25.8nm
OMN
SGJ
{>Leg
>117kt
APT VOR NDB SUP ACT NAV FPL CAL SET OTH
Menu?
100
KJAX
%
%
"
%
SGJ
%
KCVN
17.6nm
SGJ
{>Leg
>117kt
SUA:off
VOR:off
APT:off
112°
APT VOR NDB SUP ACT NAV FPL CAL SET OTH
KJAX
OMN
GJ
%
"
%
%
ORL
%
KORL
To change the navigation info displayed in the lower left corner:
1. Press the
B button.
2. Use the right outer knob to move the cursor to the cyclic field in the lower
left corner.
3. Press
E to change between the choices, which are:
• Groundspeed (figure 5),
• Estimated Time En route (ETE) to the active waypoint (figure 6),
• Crosstrack correction (figure 7), or
• Magnetic Desired Track (DTK) (figure 8).
To scan through the active flight plan waypoints:
1. Pull out and turn the right inner knob (figure 9).
2. With desired waypoint displayed in scanning window, press
D to go
direct-to the selected waypoint.
-4-
Figure 7 Figure 8
Figure 9
Figure 5
Figure 6
17.6nm
SGJ
{>Leg
>117kt
APT VOR NDB
17.6nm
SGJ
{>Leg
> 1.2∆
17.6nm
SGJ
{>Leg
> 1:23
APT VOR NDB
17.6nm
SGJ
{>Leg
> 123
DTK
APT VOR NDB
APT VOR NDB
17.6nm
SGJ
{>Leg
>117kt
SUA:on
VOR:off
APT:on
123°
APT VOR NDB SUP ACT NAV FPL CAL SET OTH
KJAX
OMN
GJ
%
"
%
%
SGJ
ORL
%
KORL
To create a Flight Plan:
1. Select the active Flight Plan (FPL 0) or one of the stored Flight Plans
(FPL 1 through FPL 9) on the screen.
2. Delete existing waypoints from the Flight Plan as necessary by placing
the cursor (
B) over the identifier, pressing E, and then pressing
F.
3. If you wish to insert a waypoint identifier between two other waypoints,
place the cursor (
B) over the waypoint you wish for the new waypoint
to precede.
4. With the cursor on, enter the desired waypoint identifier and press
F.
5. The waypoint page for the selected identifier will be displayed. If this is
the waypoint you intended to enter, press
F again.
6. Repeat the waypoint entry process as needed for your Flight Plan.
To use a stored Flight Plan:
1. Select the desired Flight Plan page (FPL 1 through FPL 9)
2. Press the
B button to turn on the cursor over Use?.
3. If you wish to use the Flight Plan in the order displayed, press
F. If
you wish to reverse the Flight Plan and use it, rotate the right outer knob
one stop clockwise, putting the cursor over Use? Inverted? and press
F. The FPL 0 page will be displayed with your selected Flight Plan.
To create a user-defined waypoint at your present position:
1. Go to a Supplemental page (SUP 1, 2, or 3) and turn on the cursor
(B).
2. Spell out the name of your new user-defined waypoint on the top line,
using the right outer and right inner knobs.
3. Move the cursor to the bottom line of the screen, over Present Pos? and
press
F.
To calculate the winds aloft:
1. Use the CAL 3 page to calculate the present pressure altitude.
2. Use the CAL 5 page to calculate the present true airspeed
(TAS).
3. Turn to the CAL 6 page and
enter the present aircraft heading. The headwind or tailwind
component of the wind, and the
wind vector (direction and
speed) will be displayed on the
last two lines of the CAL 6 page (figure 10).
-5-
Figure 10
17.6nm TAS: 136kt
SGJ Hdg: 025°
>Leg Headwind 002kt
CRSR 110°True 20kt
APT VOR NDB SUP ACT NAV FPL CAL SET OTH
Finding your way around:
There are ten types of pages that may be displayed on the right side of the screen.
Each has multiple page numbers:
AlliedSignal General Aviation Avionics
400 North Rogers Road
Olathe, Kansas 66062-1212
TELEX 669916 KINGRAD • FAX 913-791-1302
TELEPHONE (913) 768-3000
© 1995 AlliedSignal Inc.
5/95 006-08792-0000 2K Printed in USA
A
Airport (APT) Pages
1 Airport identifier, elevation, name, city,
state/province/country, use type (if
military or private-use)
2 Latitude/longitude, bearing/radial and
distance relative to present position
3 Runway numbers, length, surface, lighting
4 Airport communication frequencies
5 Airport remarks
VOR Pages
1 VOR identifier, frequency, name,
latitude/longitude
2 Magnetic station declination, bearing/
radial, distance relative to present position
NDB Pages
1 NDB identifier, frequency, name,
latitude/longitude
2 Bearing/radial and distance relative to
present position
Supplemental (SUP) Pages
0 Used to choose method of user-defined
waypoint creation
1 Latitude/Longitude, bearing/radial and
distance relative to present position
2 Reference waypoint (default is nearby
VOR), radial and distance from reference
3 User-defined waypoint remarks
Active Waypoint (ACT) Pages
Waypoint pages for the active waypoint
and the waypoints in FPL 0
Navigation (NAV) Pages
1 Active waypoint/leg, CDI/crosstrack
distance, desired track, actual track,
bearing, time to active waypoint
2 Present position (latitude/longitude or
radial/distance)
3 Present time, departure time, ETA at
destination, elapsed flight time
4 Moving map
Flight Plan (FPL) Pages
0 Active flight plan
1-9 Stored (numbered) flight plans
Calculator (CAL) Pages
1 Trip calculations for distance, bearing,
and ETE
2 Trip calculations for fuel requirements
3 Pressure altitude
4 Density altitude
5 True airspeed (TAS)
6 Winds aloft
Setup (SET) Pages
1 Position initialization for GPS receiver
2 Date, time, and time zone initialization
3 Data base update
4 Turn anticipation enable/disable
5 Default first waypoint character
6 Nearest airport criteria
7 SUA alert enable/disable
8 Baro set, indicated altitude, baro set units
Other (OTH) Pages
1 GPS receiver state, estimated position
error
2 GPS satellite signal status
3 List of user-defined waypoints
4 List of airports and user-defined
waypoints with stored remarks
5 Software versions, total hours of
operation, total power cycles
Loading...