ARISTON ARM7L 125 S (EX) User Manual

Instructions for use

WASHER DRYER

!	This symbol reminds you to read this
			GB
instruction manual.

GB FR AR

English,1

Français,13

,25

ARM7L 125 S

Contents

Installation, 2-3

Unpacking and levelling

Connecting the electricity and water supplies The first wash cycle

Technical data

Care and maintenance, 4

Cutting off the water or electricity supply Cleaning the washer-dryer

Cleaning the detergent dispenser drawer Caring for the door and drum of your appliance Cleaning the pump

Checking the water inlet hose

Precautions and tips, 5

General safety

Disposal

Description of the washer-dryer and starting a wash cycle, 6-7

Control panel Indicator lights Starting a wash cycle

Wash cycles, 8

Table of wash cycles

Personalisation, 9

Setting the temperature

Setting the drying cycle

Functions

Detergents and laundry, 10

Detergent dispenser drawer

Bleach cycle

Preparing the laundry

Garments requiring special care

Load balancing system

Troubleshooting, 11

Service, 12

1

Installation

! This instruction manual should be kept in a safe GB place for future reference. If the washing machine is sold, transferred or moved, make sure that the instruction manual remains with the machine so that the new owner is able to familiarise himself/

herself with its operation and features.

! Read these instructions carefully: they contain vital information relating to the safe installation and operation of the appliance.

Unpacking and levelling

Unpacking

1.Removethewashingmachinefromitspackaging.

2.Make sure that the washing machine has not been damaged during the transportation process. If it has been damaged, contact the retailer and do notproceedanyfurtherwiththeinstallationprocess.

3. Remove the 4 protective screws (used during transportation) and the rubber washer with the corresponding spacer, located on the rear part of the appliance (see figure).

4.Close off the holes using the plastic plugs provided.

5.Keep all the parts in a safe place: you will need them again if the washing machine needs to be moved to another location.

! Packaging materials should not be used as toys for children.

Levelling

1. Install the washing machine on a flat sturdy floor, without resting it up against walls, furniture cabinets or anything else.

2. If the floor is not perfectly level, compensate for any unevenness by tightening

or loosening the adjustable front feet (see figure); the angle of inclination, measured in relation to the worktop, must not exceed 2°.

Levelling the machine correctly will provide it with stability, help to avoid vibrations and excessive noise and prevent it from shifting while it is operating. If it is placed on carpet or a rug, adjust the feet in such a way as to allow a sufficient ventilation space underneath the washing machine.

Connecting the electricity and water supplies

Connecting the water inlet hose

1. Connect the supply pipe by screwing it to a cold water tab using a ¾ gas threaded connection (see figure).

Before performing the connection, allow the water to run freely until it is perfectly clear.

2. Connect the inlet hose to the washing machine by screwing it onto the corresponding water inlet of the appliance, which is situated on the top righthand side of the rear part of the appliance

(see figure).

3. Make sure that the hose is not folded over or bent.

! The water pressure at the tap must fall within the values indicated in the Technical details table

(see next page).

!If the inlet hose is not long enough, contact a specialised shop or an authorised technician.

!Never use second-hand hoses.

!Use the ones supplied with the machine.

2

Connecting the drain hose

65 - 100 cm

Connect the drain hose, without bending it, to a drainage duct or a wall drain located at a height between 65 and 100 cm from the floor;

alternatively, rest it on the side of a washbasin or bathtub, fastening the duct supplied to the tap (see figure). The free end of the hose should not be underwater.

! We advise against the use of hose extensions; if it is absolutely necessary, the extension must have the same diameter as the original hose and must not exceed 150 cm in length.

Electrical connections

Before plugging the appliance into the electricity socket, make sure that:

•the socket is earthed and complies with all applicable laws;

•the socket is able to withstand the maximum power load of the appliance as indicated in the Technical data table (see opposite);

•the power supply voltage falls within the values indicatedintheTechnicaldatatable(seeopposite);

•the socket is compatible with the plug of the washing machine. If this is not the case, replace the socket or the plug.

!The washing machine must not be installed outdoors, even in covered areas. It is extremely dangerous to leave the appliance exposed to rain, storms and other weather conditions.

!When the washing machine has been installed, the electricity socket must be within easy reach.

!Do not use extension cords or multiple sockets.		GB

!The cable should not be bent or compressed.

!The power supply cable must only be replaced by authorised technicians.

Warning!Thecompanyshallnotbeheldresponsible intheeventthattheseregulationsarenotrespected.

The first wash cycle

Once the appliance has been installed, and before you use it for the first time, run a wash cycle with detergent and no laundry, using the wash cycle 1.

Technical data

	Model	ARM7L 125 S
		width 59.5 cm
	Dimensions	height 85 cm
		depth 53,5 cm
		from 1 to 7 kg for the wash
	Capacity	programme;
		from 1 to 5 kg for the drying
		programme
	Electrical	please refer to the technical
	connections	data plate fixed to the machine
		maximum pressure 1 MPa
	Water con-	(10 bar)
		minimum pressure 0.05 MPa
	nections	(0.5 bar)
		drum capacity 52 litres
	Spin speed	up to 1200 rotations per minute
		Wash: programme 6; tempera-
		ture 60°C; using a load of 7 kg.
	Energy rated	Drying: first drying cycle perfor-
	programmes	med with a 2 kg load, by selec-
	according to	ting the	dryness level.
	EN 50229	The second drying cycle is per-
		formed with a 5 kg load, by se-
		lecting the	dryness level.

This appliance conforms to the following EC Directives: - 2004/108/CE (Electromagnetic Compatibility) and subsequent modifications - 2012/19/EU (WEEE)

- 2006/95/EC (Low Voltage)

3

Care and maintenance

		Cutting off the water and electri-
	GB
		city supplies
		• Turn off the water tap after every wash cycle.
		This will limit wear on the hydraulic system
		inside the washer-dryer and help to prevent
		leaks.
		• Unplug the washer-dryer when cleaning it
		and during all maintenance work.

Cleaning the washer-dryer

The outer parts and rubber components of the appliance can be cleaned using a soft cloth soaked in lukewarm soapy water. Do not use solvents or abrasives.

Cleaning the detergent dispenser drawer

1

2

Remove the dispenser by raising it and pulling it out (see figure). Wash it under running water; this operation should be repeated frequently.

Caring for the door and drum of your appliance

•Always leave the porthole door ajar in order to prevent unpleasant odours from forming.

Cleaning the pump

The washer-dryer is fitted with a self-cleaning pump which does not require any maintenance. Sometimes, small items (such as coins or buttons) may fall into the pre-chamber which protects the pump, situated in its bottom part.

! Make sure the wash cycle has finished and unplug the appliance.

To access the pre-chamber:

1. using a screwdriver, remove the cover panel on the lower front part of the washer-dryer (see figure);

2. unscrew the lid by rotating it anticlockwise (see figure): a little water may trickle out. This is perfectly normal;

3.clean the inside thoroughly;

4.screw the lid back on;

5.reposition the panel, making sure the hooks are securely in place before you push it onto the appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If there are any cracks, it should be replaced immediately: during the wash cycles, water pressure is very strong and a cracked hose could easily split open.

! Never use second-hand hoses.

4

Precautions and tips

! This Washer-dryer was designed and constructed in accordance with international safety regulations. The following information is provided for safety reasons and must therefore be read carefully.

General safety

•This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

-Do not dry unwashed items in the tumble dryer.

-Items that have been soiled with substances such as cooking oil, acetone, alcohol, petrol, kerosene, spot removers, turpentine, waxes and wax removers should be washed in hot water with an extra amount of detergent before being dried in the tumble dryer.

-Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber backed articles and clothes or pillows fitted with foam rubber pads should not be dried in the tumble dryer.

-Fabric softeners, or similar products, should be used as specified by the fabric softener instructions.

-The final part of a tumble dryer cycle occurs without heat (cool down cycle) to ensure that the items are left at a temperature that ensures that the items will not be damaged.

WARNING: Never stop a tumble dryer before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated.

•This appliance was designed for domestic use only.

•Do not touch the machine when barefoot or with wet or damp hands or feet.

•Do not pull on the power supply cable when unplugging the appliance from the electricity socket. Hold the plug and pull.

•Do not open the detergent dispenser drawer while the machine is in operation.

•Do not touch the drained water as it may reach extremely high temperatures.

•Never force the porthole door. This could damage the safety lock mechanism designed to prevent accidental opening.

•If the appliance breaks down, do not under any circumstances access the internal mechanisms in an attempt to repair it yourself.

•Always keep children well away from the appliance while it is operating.

	• The door can become quite hot during the wash cycle.
			GB
	• If the appliance has to be moved, work in a group of
	two or three people and handle it with the utmost care.
	Never try to do this alone, because the appliance is very
	heavy.

•Before loading laundry into the Washer-dryer, make sure the drum is empty.

•During the drying phase, the door tends to get quite hot.

•Do not use the appliance to dry clothes that

have been washed with flammable solvents (e.g. trichlorethylene).

•Do not use the appliance to dry foam rubber or similar elastomers.

•Make sure that the water tap is turned on during the

drying cycles.

•Children of less than 3 years should be kept away from the appliance unless continuously supervised.

•Remove all objects from pockets such as lighters and matches.

Disposal

•Disposing of the packaging materials: observe local regulations so that the packaging may be re-used.

•The European Directive 2012/19/EU on Waste Electrical and Electronic Equipment, requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimise the recovery and recycling of the materials they contain and reduce the impact on human health and the environment. The crossed out “wheeled bin” symbol on the product reminds you of your obligation, that when you dispose of the appliance it must be separately collected. Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance.

5

Description of the washer-dryer and starting a wash cycle

		Control panel
	GB

WASH CYCLE PROGRESS/

DELAY TIMER indicator lights

ON/OFF button

DRYING

DOOR

knob

TEMPERATURE

LOCKED

knob

indicator light

					START/PAUSE
	Detergent dispenser drawer
					button with indicator
			FUNCTION
					light
	WASH CYCLE		buttons with
			indicator lights
		knob

Detergent dispenser drawer: used to dispense detergents and washing additives (see “Detergents and laundry”).

ON/OFF button: switches the washer-dryer on and off.

WASH CYCLE knob: programmes the wash cycles. During the wash cycle, the knob does not move.

FUNCTION buttons with indicator light: used to select the available functions. The indicator light corresponding to the selected function will remain lit.

TEMPERATURE knob: sets the temperature or the cold wash cycle (see “Personalisation”).

DRYING knob: used to set the desired drying programme (see “Personalisation”).

WASH CYCLE PROGRESS/DELAY TIMER indicator lights: used to monitor the progress of the wash cycle. The illuminated indicator light shows which phase is in progress.

If the Delay Timer function has been set, the time remaining until the wash cycle starts will be indicated (see next page).

DOOR LOCKED indicator light: indicates whether the door may be opened or not (see next page).

START/PAUSE button with indicator light: starts or temporarily interrupts the wash cycles.

N.B. To pause the wash cycle in progress, press this button; the corresponding indicator light will flash orange, while the indicator light for the current wash cycle phase will remain lit in a fixed manner. If the DOOR LOCKED indicator light is switched off, the door may be opened (wait approximately 3 minutes).

To start the wash cycle from the point at which it was interrupted, press this button again.

Standby mode

This washing machine, in compliance with new energy saving regulations, is fitted with an automatic standby system which is enabled after about 30 minutes if no activity is detected. Press the ON-OFF button briefly and wait for the machine to start up again.

Consumption in off-mode: 0,5 W Consumption in Left-on: 8 W

6

Indicator lights

The indicator lights provide important information. This is what they can tell you:

Delayed start

If the DELAY TIMER function has been activated (see “Personalisation”), after the wash cycle has been started the indicator light corresponding to the selected delay period will begin to flash:

As time passes, the remaining delay will be displayed and the corresponding indicator light will flash:

Once the set delay has elapsed, the flashing indicator light will switch off and the selected wash cycle will begin.

Starting a wash cycle

Wash cycle phase indicator lights

Once the desired wash cycle has been selected and has be- GB gun, the indicator lights switch on one by one to indicate which

phase of the cycle is currently in progress.

Wash

Rinse

	Spin	Note: as soon as a drying level
		or time period has been set,
		this indicator light illuminates
	Drying	to indicate that the selected
		wash cycle will be followed by a
	End of wash cycle	drying phase.

Note: during the “Drain” phase, the indicator light corresponding to the “Spin” cycle phase will illuminate.

Function buttons and corresponding indicator lights

When a function is selected, the corresponding indicator light will illuminate.

If the selected function is not compatible with the programmed wash cycle, the corresponding indicator light will flash and the function will not be activated.

If a function which is incompatible with another function selected previously, only the most recent selection will remain active.

Door locked indicator light

If this indicator light is on, the appliance door is locked to prevent it from being opened accidentally; to avoid any damage, wait for the indicator light to switch off before you open the appliance door (wait approximately 3 minutes). N.B. If the DELAY TIMER function is activated, the door cannot be opened; pause the machine by pressing the START/PAUSE button if you wish to open it.

! If the START/PAUSE indicator light (orange) flashes rapidly at the same time as the function indicator light, this indicates a problem has occurred (see “Troubleshooting”).

1.Turn the washing machine on by pressing the ON/OFF button. All the indicator lights will turn on for a few seconds, then only the indicator lights relative to the selected programme settings will remain lit and the START/PAUSE indicator light will flash.

2.Load the laundry and close the door.

3.Set the WASH CYCLE knob to the desired programme.

4.Set the washing temperature (see “Personalisation”).

5.Set the drying cycle if necessary (see “Personalisation”).

6.Measure out the detergent and washing additives (see “Detergents and laundry”).

7.Select the desired functions.

8.Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit in a fixed manner, in green. To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle.

9.At the end of the wash cycle the indicator light will switch on. The DOOR LOCKED indicator light will switch off, indicating that the door may be opened (wait approximately 3 minutes). Take out your laundry and leave the appliance door ajar to make sure the drum dries completely. Switch the washer-dryer off by pressing the ON/OFF button.

7

Wash cycles

		Table of wash cycles
	GB
		cycles	Description of the wash cycle
		Wash

Specials cycles

6Sanitizing cycle: Extremely soiled whites.

6Sanitizing cycle (1): Heavily soiled whites and resistant colours.

6Sanitizing cycle (2): Lightly soiled whites and resistant colours. 7 Goodnigt cycle: Lightly soiled delicate colours.

8 Baby cycle: Heavily soiled delicate colours.

9 Silk/Curtains: For garments in silk and viscose, lingerie.

10Wool: For wool, cashmere, etc.

Daily wash cycles

1 Cotton: Heavily soiled whites and resistant colours.

2 Coloured Cottons: Lightly soiled whites and delicate colours.

3Synthetics resistents: Heavily soiled resistant colours.

3Synthetics resistents: Lightly soiled resistant colours.

4Mix 30':To refresh lightly soiled garments quickly (not suitable for wool, silk and clothes which require washing by hand).

5Mix 15': To refresh lightly soiled garments quickly (not suitable for wool, silk and clothes which require washing by hand).

Partials wash cycles

A Rinse

B Spin

CDrain no spin

Drying cycles

11Cotton drying

12Synthetics drying

13Wool drying

Max.	Max.			Detergents					Max.
										Cycle
temp.	speed	Drying							load	duration
(°C)	(rpm)			Bleach		Wash		Fabric	(kg)
								softener
90°										190’
	1200								7
60°	1200			-					7	180’
40°	1200			-					7	170’
40°	800	-		-					4	290’
40°	1000			-					4	145’
30°	0	-		-					1	55’
40°	800			-					1,5	70’
60°										140’
	1200								7
40°	1200								7	90’
60°	800			-					3	115’
40°	800			-					3	100’
30°	800	-		-					3	30’
30°	800	-		-					1,5	15’
-										36’
	1200			-		-			7
-	1200			-		-		-	7	10’
-	0	-		-		-		-	7	3’
-		
	-			-		-		-	5	-
-	-			-		-		-	3	-
-	-			-		-		-	1,5	-

The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary according to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.

For all Test Institutes:

1)Test wash cycle in compliance with regulation EN 50229: set wash cycle 6 with a temperature of 60°C.

2)Long wash cycle for cottons: set wash cycle 6 with a temperature of 40°C.

Specials wash cycles

Sanitizing cycle (wash cycle 6). A high-temperature hygienic wash cycle (over 60°C) which requires the use of bleach. Pour the bleach, the detergent and the additives into the relevant compartments (see paragraph entitled “Detergent dispenser drawer”).

Goodnigt cycle (wash cycle 7). This is a silent cycle which can be run at night, when the electricity prices are lower. The wash cycle is designed for cottons and synthetics. At the end of the cycle the machine stops while there is still water in the drum; to spin and drain the laundry press the START/PAUSE button; alternatively the machine will perform the spin cycle and drain the water automatically after 8 hours.

Baby cycle (wash cycle 8). This wash cycle can be used to remove the soiling typically caused by babies, while ensuring that all detergent is removed from nappies in order to prevent the delicate skin of babies from suffering allergies. The cycle has been designed to reduce the amount of bacteria by using a greater quantity of water and optimising the effect of special disinfecting additives added to the detergent.

Mix 30’(wash cycle 4) this wash cycle was designed to wash lightly soiled garments quickly: it lasts just 30 minutes and therefore saves both energy and time. By selecting this wash cycle (5 at 30°C), it is possible to wash different fabrics together (except for wool and silk items), with a maximum load of 3 kg.

Mix 15’(wash cycle 5) this wash cycle was designed to wash lightly soiled garments quickly: it lasts just 15 minutes and therefore saves both energy and time. By selecting this wash cycle (5 at 30°C), it is possible to wash different fabrics together (except for wool and silk items), with a maximum load of 1.5 kg.

8

Personalisation

Setting the temperature
										GB
Turn the TEMPERATURE knob to set the wash temperature (see Table of wash cycles).
The temperature may be lowered, or even set to a cold wash (	).
The washer-dryer will automatically prevent you from selecting a temperature which is higher than the maximum value set for
each wash cycle.
Setting the drying cycle	Table of Drying times (guideline values)
Turn the DRYING knob to set the desired drying type.
Two options are available:		Fabric		Max.	Cupboard	Hanger		Iron
A - Based on time: from 40 to 180 minutes.
			Load type	load	dry		dry	dry
B - Based on the how damp the clothes are once they have		type		(kg)
been dried:
Iron : slightly damp clothes, easy to iron.		Cotton	Clothing of different	5	250	210		190
Hanger : dry clothes to put away.			sizes, Terry towels
Cupboard : very dry clothes, recommended for towelling
		Syn-	Sheets, Shirts, Py-
and bathrobes.				3	180	130		115
If your laundry load to be washed and dried is much greater		thetics	jamas, socks, etc.
than the maximum stated load (see adjacent table), perform		Wool	Knitwear, Pullovers,	1,5	155	135		115
the wash cycle, and when the cycle is complete, divide the
			etc.

garments into groups and put some of them back in the drum.

At this point, follow the instructions provided for a “Drying only” cycle. Repeat this procedure for the remainder of the load. N.B: When the drying is complete there is a cooling period, even though the DRYING knob is in the position.

Drying only

Turn the WASH CYCLE knob to one of the drying settings (11-12-13) according to the type of fabric, then select the desired drying duration using the DRYING knob.

Functions

The various wash functions available with this washer-dryer will help to achieve the desired results, every time. To activate the functions:

1.Press the button corresponding to the desired function;

2.the function is enabled when the corresponding indicator light is illuminated.

Note:

-If the selected function is not compatible with the programmed wash cycle, the corresponding indicator light will flash and the function will not be activated.

-If a function which is incompatible with another function selected previously, only the most recent selection will remain active.

Delay timer

This timer delays the start time of the wash cycle by up to 9 hours.

Press the button repeatedly until the indicator light corresponding to the desired delay time switches on. The fifth time the button is pressed, the function will be disabled.

N.B. Once you have pressed the START/PAUSE button, the delay time may only be decreased if you wish to modify it.

Extra rinse

By selecting this function, the efficiency of the rinse is increased and optimal detergent removal is guaranteed. It is particularly useful for sensitive skin.

Super Wash

Because a greater quantity of water is used in the initial phase of the cycle, and because of the increased cycle duration, this function offers a high-performance wash.

1200-600

By selecting this function, reduces the spin speed.

9

Detergents and laundry

		Detergent dispenser drawer
	GB
		Good washing results also depend on the correct dose of
		detergent: adding too much detergent will not necessa-
		rily result in a more efficient wash, and may in fact cause
		build up on the inside of your appliance and contribute to
		environmental pollution.
		!Use powder detergent for white cotton garments, for pre-
		washing, and for washing at temperatures over 60°C.
		!Follow the instructions given on the detergent packaging.
		! Do not use hand washing detergents because these
		create too much foam.

MAX	3
2	1

Open the detergent dispenser drawer and pour in the detergent or washing additive, as follows.

compartment 1: Detergent for the wash cycle (powder or liquid)

Liquid detergent should only be poured in immediately prior to the start of the wash cycle.

compartment 2: Additives (fabric softeners, etc.)

The fabric softener should not overflow the grid. extra compartment 3: Bleach

Bleach cycle

Bleaching may only be performed in conjunction with wash cycles 1, 2, 6.

Pour the bleach into extra compartment 3; pour the detergent and softener into the corresponding compartments, then select one of the abovementioned wash cycles.

This option is recommended only for very soiled cotton garments.

Preparing the laundry

•Divide the laundry according to:

-the type of fabric/the symbol on the label

-the colours: separate coloured garments from whites.

•Empty all garment pockets and check the buttons.

•Do not exceed the values listed in the “Table of wash cycles”, which refer to the weight of the laundry when dry.

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1200 g

1 towel 150-250 g

Garments requiring special care

Silk: use special wash cycle 9 to wash all silk garments. We recommend the use of special detergent which has been designed to wash delicate clothes.

Curtains: these should be folded and placed inside the bag provided. Use wash cycle 9.

Wool: All wool garments can be washed using programme 10 even those carrying the “hand-wash only” label. For best results, use special detergents and do not exceed 1,5 kg of laundry.

Load balancing system

Before every spin cycle, to avoid excessive vibrations and to distribute the load in a uniform manner, the drum rotates continuously at a speed which is slightly greater than the washing rotation speed. If, after several attempts, the load is not balanced correctly, the machine spins at a reduced spin speed. If the load is excessively unbalanced, the washer-dryer performs the distribution process instead of spinning. To encourage improved load distribution and balance, we recommend small and large garments are mixed in the load.

10

Troubleshooting

	Your washer-dryer could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure that
				GB
	the problem cannot be solved easily using the following list.

Problem:

The washer-dryer does not switch on.

The wash cycle does not start.

The washer-dryer does not take in water (the indicator light for the first wash cycle stage flashes rapidly).

The washer-dryer continuously takes in and drains water.

The washer-dryer does not drain or spin.

The washer-dryer vibrates a lot during the spin cycle.

The washer-dryer leaks.

The START/PAUSE indicator light (orange) and the function indicator lights flash rapidly.

There is too much foam.

The washer-dryer does not dry.

Possible causes / Solutions:

•The appliance is not plugged into the socket fully, or is not making contact.

•There is no power in the house.

•The washer-dryer door is not closed properly.

•The ON/OFF button has not been pressed.

•The START/PAUSE button has not been pressed.

•The water tap has not been opened.

•A delayed start has been set (see “Personalisation”).

•The water inlet hose is not connected to the tap.

•The hose is bent.

•The water tap has not been opened.

•There is no water supply in the house.

•The pressure is too low.

•The START/PAUSE button has not been pressed.

•The drain hose is not fitted at a height between 65 and 100 cm from the floor (see “Installation”).

•The free end of the hose is under water (see “Installation”).

•The wall drainage system is not fitted with a breather pipe.

If the problem persists even after these checks, turn off the water tap, switch the appliance off and contact the Assistance Service. If the dwelling is on one of the upper floors of a building, there may be problems relating to water drainage, causing the washer-dryer to fill with water and drain continuously. Special antidraining valves are available in shops and help to avoid this inconvenience.

•The wash cycle does not include draining: some wash cycles require the drain phase to be started manually.

•The drain hose is bent (see “Installation”).

•The drainage duct is clogged.

•The drum was not unlocked correctly during installation (see “Installation”).

•The washer-dryer is not level (see “Installation”).

•The washer-dryer is trapped between cabinets and walls (see “Installation”).

•The water inlet hose is not screwed on properly (see “Installation”).

•The detergent dispenser drawer is blocked (for cleaning instructions, see “Care and maintenance”).

•The drain hose is not fixed properly (see “Installation”).

•Switch off the machine and unplug it, wait for approximately 1 minute and then switch it back on again.

If the problem persists, contact the Technical Assistance Service.

•The detergent is not suitable for machine washing (it should display the text “for washer-dryers” or “hand and machine wash”, or the like).

•Too much detergent was used.

•The appliance is not plugged into the socket, or not enough to make contact.

•There has been a power failure.

•The appliance door is not shut properly.

•A delayed start has been set.

•The DRYING knob is on the setting.

11