Cisco Systems 3800 User Manual

Name: Cisco Systems 3800
Brand: Cisco Systems
SKU: 1024069
Rating: 5 (1 reviews)

5 (1)

Introduction to Cisco 3800 Series Routers

Hardware Documentation

This introduction discusses the objectives, audience, and conventions of hardware documentation for Cisco 3800 series integrated services routers, and describes related documents where you can find additional information. It contains the following sections:

•Objectives and Organization, page 1

•Audience, page 2

•Conventions, page 2

•Safety Warnings, page 3

•Related Documentation, page 9

•Cisco 90-Day Limited Hardware Warranty Terms, page 10

•Obtaining Documentation, page 11

•Documentation Feedback, page 12

•Obtaining Technical Assistance, page 12

•Obtaining Additional Publications and Information, page 13

Objectives and Organization

This series of documents provides comprehensive hardware information for Cisco 3800 series integrated services routers. It includes the following modules:

•Overview of Cisco 3800 Series Routers

•Preinstallation Requirements and Planning for Cisco 3800 Series Routers

•Installing Cisco 3800 Series Routers in an Equipment Rack

•Connecting Cables to Cisco 3800 Series Routers

•Powering Up Cisco 3800 Series Routers

•Troubleshooting Cisco 3800 Series Routers

•Installing Network Modules in Cisco 3800 Series Routers

•Installing Interface Cards in Cisco 3800 Series Routers

•Installing SFP Modules in Cisco 3800 Series Routers

Introduction to Hardware Documentation

	OL-5965-01	1

Audience

•Installing CompactFlash Memory Cards in Cisco 3800 Series Routers

•Installing and Upgrading Internal Components in Cisco 3800 Series Routers

For software configuration information, see the Cisco 3800 series software configuration documents and the Cisco IOS configuration guides and command references. These publications are available online on Cisco.com. See the “Obtaining Documentation” section on page 11 for more information.

For warranty, service, and support information, see the “Cisco 90-Day Limited Hardware Warranty Terms” section on page 10.

These documents describe several router models that are similar in functionality, but differ in certain respects. Some information may not apply to all router models.

Audience

These documents are intended for the person installing, configuring, and maintaining the router, who should be familiar with electronic circuitry and wiring practices and have experience as an electronic or electromechanical technician. Certain identified procedures should be performed only by trained and qualified personnel.

Conventions

These documents use the conventions listed in Table 1.

Table 1 Document Conventions

Convention		Description
boldface font		Commands and keywords.

italic font		Variables for which you supply values.

[	]	Optional keywords or arguments.

{x \| y \| z}		A choice of required keywords. You must select exactly one.

screen font		Information displayed on the screen.

boldface screen font		Information you must enter.

<	>	Nonprinting characters, such as passwords, appear in angle brackets in contexts where italics are
		not available.

[	]	Default responses to system prompts.

Note Means reader take note. Notes contain helpful suggestions or references to material not covered in the manual.

Timesaver Means the described action saves time. You can save time by performing the action described in the paragraph.

Introduction to Hardware Documentation

2	OL-5965-01

Safety Warnings

Tip Means the following information will help you solve a problem. The tips information might not be troubleshooting or even an action, but could be useful information, similar to a Timesaver.

Caution Means reader be careful. In this situation, you might do something that could result in equipment damage or loss of data.

Safety Warnings

Safety warnings appear throughout these documents in procedures that, if performed incorrectly, may harm you. A warning symbol precedes each warning statement. To see translations of the warnings that appear in this publication, see the Cisco 3800 Series Routers Regulatory Compliance and Safety Information document that accompanied your router.

Warning IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071

SAVE THESE INSTRUCTIONS

Waarschuwing BELANGRIJKE VEILIGHEIDSINSTRUCTIES

Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt raadplegen.

BEWAAR DEZE INSTRUCTIES

Varoitus TÄRKEITÄ TURVALLISUUSOHJEITA

Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien lausuntonumeroiden avulla.

SÄILYTÄ NÄMÄ OHJEET

Introduction to Hardware Documentation

	OL-5965-01	3

Safety Warnings

Attention IMPORTANTES INFORMATIONS DE SÉCURITÉ

Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.

CONSERVEZ CES INFORMATIONS

Warnung WICHTIGE SICHERHEITSHINWEISE

Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.

BEWAHREN SIE DIESE HINWEISE GUT AUF.

Avvertenza IMPORTANTI ISTRUZIONI SULLA SICUREZZA

Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento.

CONSERVARE QUESTE ISTRUZIONI

Advarsel VIKTIGE SIKKERHETSINSTRUKSJONER

Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne enheten.

TA VARE PÅ DISSE INSTRUKSJONENE

Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.

GUARDE ESTAS INSTRUÇÕES

Introduction to Hardware Documentation

4	OL-5965-01

Safety Warnings

¡Advertencia! INSTRUCCIONES IMPORTANTES DE SEGURIDAD

Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo.

GUARDE ESTAS INSTRUCCIONES

Varning! VIKTIGA SÄKERHETSANVISNINGAR

Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning.

SPARA DESSA ANVISNINGAR

Introduction to Hardware Documentation

	OL-5965-01	5

Safety Warnings

Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.

GUARDE ESTAS INSTRUÇÕES

Advarsel VIGTIGE SIKKERHEDSANVISNINGER

Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed.

GEM DISSE ANVISNINGER

Introduction to Hardware Documentation

6	OL-5965-01

Safety Warnings

Introduction to Hardware Documentation

	OL-5965-01	7

Safety Warnings

Introduction to Hardware Documentation

8	OL-5965-01

Cisco 90-Day Limited Hardware Warranty Terms

There are special terms applicable to your hardware warranty and various services that you can use during the warranty period. Your formal Warranty Statement, including the warranties and license agreements applicable to Cisco software, is available on Cisco.com. Follow these steps to access and download the Cisco Information Packet and your warranty and license agreements from Cisco.com.

1.Launch your browser, and go to this URL: http://www.cisco.com/univercd/cc/td/doc/es_inpck/cetrans.htm The Warranties and License Agreements page appears.

2.To read the Cisco Information Packet, follow these steps:

a.Click the Information Packet Number field, and make sure that the part number 78-5235-03A0 is highlighted.

b.Select the language in which you would like to read the document.

c.Click Go.

The Cisco Limited Warranty and Software License page from the Information Packet appears.

d.Read the document online, or click the PDF icon to download and print the document in Adobe Portable Document Format (PDF).

Note You must have Adobe Acrobat Reader to view and print PDF files. You can download the reader from Adobe’s website: http://www.adobe.com

3.To read translated and localized warranty information about your product, follow these steps:

a.Enter this part number in the Warranty Document Number field: 78-5236-01C0

b.Select the language in which you would like to read the document.

c.Click Go.

The Cisco warranty page appears.

d.Review the document online, or click the PDF icon to download and print the document in Adobe Portable Document Format (PDF).

You can also contact the Cisco service and support website for assistance:

http://www.cisco.com/public/Support_root.shtml.

Duration of Hardware Warranty

Ninety (90) days.

Replacement, Repair, or Refund Policy for Hardware

Cisco or its service center will use commercially reasonable efforts to ship a replacement part within ten (10) working days after receipt of a Return Materials Authorization (RMA) request. Actual delivery times can vary, depending on the customer location.

Cisco reserves the right to refund the purchase price as its exclusive warranty remedy.

Introduction to Hardware Documentation

10	OL-5965-01

Obtaining Documentation

To Receive a Return Materials Authorization (RMA) Number

Contact the company from whom you purchased the product. If you purchased the product directly from Cisco, contact your Cisco Sales and Service Representative.

Complete the information below, and keep it for reference:

Company product purchased from

Company telephone number

Product model number

Product serial number

Maintenance contract number

Obtaining Documentation

Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several ways to obtain technical assistance and other technical resources. These sections explain how to obtain technical information from Cisco Systems.

Cisco.com

You can access the most current Cisco documentation at this URL:

http://www.cisco.com/univercd/home/home.htm

You can access the Cisco website at this URL:

http://www.cisco.com

You can access international Cisco websites at this URL:

http://www.cisco.com/public/countries_languages.shtml

Ordering Documentation

You can find instructions for ordering documentation at this URL:

http://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htm

You can order Cisco documentation in these ways:

•Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from the Ordering tool:

http://www.cisco.com/en/US/partner/ordering/index.shtml

•Nonregistered Cisco.com users can order documentation through a local account representative by calling Cisco Systems Corporate Headquarters (California, USA) at 408 526-7208 or, elsewhere in North America, by calling 800 553-NETS (6387).

Introduction to Hardware Documentation

	OL-5965-01	11

Documentation Feedback

You can send comments about technical documentation to bug-doc@cisco.com.

You can submit comments by using the response card (if present) behind the front cover of your document or by writing to the following address:

Cisco Systems

Attn: Customer Document Ordering

170 West Tasman Drive

San Jose, CA 95134-9883

We appreciate your comments.

Obtaining Technical Assistance

For all customers, partners, resellers, and distributors who hold valid Cisco service contracts, Cisco Technical Support provides 24-hour-a-day, award-winning technical assistance. The Cisco Technical Support Website on Cisco.com features extensive online support resources. In addition, Cisco Technical Assistance Center (TAC) engineers provide telephone support. If you do not hold a valid Cisco service contract, contact your reseller.

Cisco Technical Support Website

The Cisco Technical Support Website provides online documents and tools for troubleshooting and resolving technical issues with Cisco products and technologies. The website is available 24 hours a day, 365 days a year at this URL:

http://www.cisco.com/techsupport

Access to all tools on the Cisco Technical Support Website requires a Cisco.com user ID and password. If you have a valid service contract but do not have a user ID or password, you can register at this URL:

http://tools.cisco.com/RPF/register/register.do

Submitting a Service Request

Using the online TAC Service Request Tool is the fastest way to open S3 and S4 service requests. (S3 and S4 service requests are those in which your network is minimally impaired or for which you require product information.) After you describe your situation, the TAC Service Request Tool automatically provides recommended solutions. If your issue is not resolved using the recommended resources, your service request will be assigned to a Cisco TAC engineer. The TAC Service Request Tool is located at this URL:

http://www.cisco.com/techsupport/servicerequest

For S1 or S2 service requests or if you do not have Internet access, contact the Cisco TAC by telephone. (S1 or S2 service requests are those in which your production network is down or severely degraded.) Cisco TAC engineers are assigned immediately to S1 and S2 service requests to help keep your business operations running smoothly.

Introduction to Hardware Documentation

12	OL-5965-01

Obtaining Additional Publications and Information

To open a service request by telephone, use one of the following numbers:

Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227)

EMEA: +32 2 704 55 55

USA: 1 800 553 2447

For a complete list of Cisco TAC contacts, go to this URL:

http://www.cisco.com/techsupport/contacts

Definitions of Service Request Severity

To ensure that all service requests are reported in a standard format, Cisco has established severity definitions.

Severity 1 (S1)—Your network is “down,” or there is a critical impact to your business operations. You and Cisco will commit all necessary resources around the clock to resolve the situation.

Severity 2 (S2)—Operation of an existing network is severely degraded, or significant aspects of your business operation are negatively affected by inadequate performance of Cisco products. You and Cisco will commit full-time resources during normal business hours to resolve the situation.

Severity 3 (S3)—Operational performance of your network is impaired, but most business operations remain functional. You and Cisco will commit resources during normal business hours to restore service to satisfactory levels.

Severity 4 (S4)—You require information or assistance with Cisco product capabilities, installation, or configuration. There is little or no effect on your business operations.

Obtaining Additional Publications and Information

Information about Cisco products, technologies, and network solutions is available from various online and printed sources.

•Cisco Marketplace provides a variety of Cisco books, reference guides, and logo merchandise. Visit Cisco Marketplace, the company store, at this URL:

http://www.cisco.com/go/marketplace/

•The Cisco Product Catalog describes the networking products offered by Cisco Systems, as well as ordering and customer support services. Access the Cisco Product Catalog at this URL:

http://cisco.com/univercd/cc/td/doc/pcat/

•Cisco Press publishes a wide range of general networking, training and certification titles. Both new and experienced users will benefit from these publications. For current Cisco Press titles and other information, go to Cisco Press at this URL:

http://www.ciscopress.com

•Packet magazine is the Cisco Systems technical user magazine for maximizing Internet and networking investments. Each quarter, Packet delivers coverage of the latest industry trends, technology breakthroughs, and Cisco products and solutions, as well as network deployment and troubleshooting tips, configuration examples, customer case studies, certification and training information, and links to scores of in-depth online resources. You can access Packet magazine at this URL:

http://www.cisco.com/packet

Introduction to Hardware Documentation

	OL-5965-01	13

Obtaining Additional Publications and Information

•iQ Magazine is the quarterly publication from Cisco Systems designed to help growing companies learn how they can use technology to increase revenue, streamline their business, and expand services. The publication identifies the challenges facing these companies and the technologies to help solve them, using real-world case studies and business strategies to help readers make sound technology investment decisions. You can access iQ Magazine at this URL:

http://www.cisco.com/go/iqmagazine

•Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering professionals involved in designing, developing, and operating public and private internets and intranets. You can access the Internet Protocol Journal at this URL:

http://www.cisco.com/ipj

•World-class networking training is available from Cisco. You can view current offerings at this URL:

http://www.cisco.com/en/US/learning/index.html

CCVP, the Cisco Logo, and the Cisco Square Bridge logo are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn is a service mark of Cisco Systems, Inc.; and Access Registrar, Aironet, BPX, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, Follow Me Browsing, FormShare, GigaDrive, GigaStack, HomeLink, Internet Quotient, IOS, iPhone, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard, iQuick Study, LightStream, Linksys, MeetingPlace, MGX, Networking Academy, Network Registrar, Packet, PIX, ProConnect, RateMUX, ScriptShare, SlideCast, SMARTnet, StackWise, The Fastest Way to Increase Your Internet Quotient, and TransPath are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.

All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0612R)

Introduction to Hardware Documentation

14	OL-5965-01

Overview of Cisco 3800 Series Routers

Cisco 3800 series integrated services routers are part of a new generation of routers that incorporate high-performance integrated data, voice, video, and virtual private network (VPN) capability, including hardware-based VPN encryption acceleration, in a modular design that provides the flexibility to configure your router according to your needs. These routers provide built-in Gigabit Ethernet LAN interface ports, and you can add a wide variety of LAN and WAN ports with interchangeable network modules and interface cards. Cisco 3800 series routers are designed for branch office installations that need integrated low-density switching, security, voice, IP telephony, video, content networking, and concurrent applications.

This document describes the features and specifications of Cisco 3800 series routers, and includes the following sections:

•Router Descriptions, page 1

•Product Identification, page 5

•Built-In Ports, page 6

•Module and Interface Card Capacity, page 7

•Port Numbering, page 9

•Memory, page 11

•Power, page 11

•LED Indicators, page 12

•Ventilation, page 12

•Real-Time Clock and Battery, page 12

•Technical Specifications, page 12

•Regulatory Compliance, page 15

Router Descriptions

There are two routers in the Cisco 3800 series—the Cisco 3825 router and the Cisco 3845 router. The Cisco 3825 router (shown in Figure 1 to Figure 4) is two rack units (3.5 inches) high. The Cisco 3845 router (shown in Figure 5 to Figure 8) is three rack units (5.25 inches) high.

Overview of Cisco 3800 Series Routers

	OL-5966-01	1

Router Descriptions

Figure 1 Front View of Cisco 3825 Router

COMPACT FLASH	1
	0

SYS	AUX
	AUX	ACT	RPS	IP
				PWR AIM0	AIM1	PV
					AIM1	PV
						DM0 PVDM1	PVDM2 PVDM3
							PVDM2 PVDM3

Figure 2 Front Panel of Cisco 3825 Router

100-240 V~ 3A

50/60 Hz

COMPACT FLASH

SYS

AUX

SYS

ACT

PWR

RPS

PWR

AIM0

AIM1

PVDM0

PVDM1

PVDM2

PVDM3

DO NOT REMOVE DURING NETWORK OPERATION

116841

1	Cisco Redundant Power System (RPS) connector		4	LED indicators

2	CompactFlash memory card slot		5	Power switch

3	USB ports		6	Power connector (AC shown)

	Figure 3	Rear View of Cisco 3825 Router

NMD-

ESW-

35x

GE1

10/100/1000

17x

FastEthernet Ports

Base-Tx

NM-

35x

17x

34x

ESW-

16x

33x

15x

32x

15x

14x

31x

FastEthernet Ports

13x

30x

12x

29x 11x

28x

18x

10x

27x 9x

Ext

26x

25x

-48V

Pwr

24x

GE0

Ext

23x

22x

10/100/

21x 3x

1000

Pwr

20x 2x

Base-Tx

15x 7x

14x

-48V

19x

18x

13x

10/100/

12x

11x

1000

10x

Base-Tx

122285

Overview of Cisco 3800 Series Routers

2	OL-5966-01

Router Descriptions

Figure 4 Rear Panel of Cisco 3825 Router

NMD-			FastEthernet Ports
ESW-		35x	FastEthernet Ports
ESW-			18x	Ext
36			18x	Ext
36	GE1			Pwr
			-48V	GE0
				10/100/
				1000
				Base-Tx
	10/100/1000			EN
	10/100/1000	17x	0x
2	Base-Tx

35x 17x 34x 16x 33x 15x 32x 14x 31x 13x 30x 12x 29x 11x 28x 10x 27x 9x 26x 8x 25x 17 24x 6x 23x 5x 22x 4x 21x 3x 20x 2x 19x 1x 18x 0x

NM-

FastEthernet Ports

ESW- 15x

Ext

Pwr

-48V

10/100/

1000

Base-Tx

15x

14x

13x

12x

11x

10x

3 4 5 6 7

H	CONSOLE	SPD	GE 0/1	LNK
H
W
I
C
2					Cisco 3825
H
W
I
C
0	AUX	SPD	GE 0/0 LNK			SFP
	8		9		10	116842
	8		9		10

1	Network module slot 2		6	HWIC slot 2

2	Screw holes for grounding lug		7	HWIC slot 0

3	Network module slot 1		8	Console and auxiliary ports

4	HWIC slot 3		9	Gigabit Ethernet ports

5	HWIC slot 1		10	Slot for optional SFP module

Figure 5		Front View of Cisco 3845 Router

117045

Overview of Cisco 3800 Series Routers

	OL-5966-01	3

Router Descriptions

Figure 6 Front Panel of Cisco 3845 Router

	1
2	3	4	116843

1	LED indicators		3	Power connector (AC shown)

2	Power switch		4	Location of optional second power supply

	Figure 7	Rear View of Cisco 3845 Router

117774

Overview of Cisco 3800 Series Routers

4	OL-5966-01

Product Identification

Figure 8 Rear Panel of Cisco 3845 Router

1	2	3	4	15	5	6	7	8	9
1	2					6		8	9
	CONSOLE						SPD	GE 0/1	LNK
	CONSOLE						SPD		LNK
1							SPD		LNK
							SPD		LNK

0	HWIC 3		HWIC 1	PVDM 3 PVDM 2 PVDM 1 PVDM 0 AIM 1	AIM 0	HWIC 0
		HWIC 2					SFP
	AUX	HWIC 2	CF				GE 0/0
	AUX	Do Not Remove During Network Operation	CF				GE 0/0

				3
				CISCO3845
4
				1
2
10	11	12	13	14

116844

1	USB ports	8	Gigabit Ethernet ports

2	Console and auxiliary ports	9	Slot for optional SFP module

3	HWIC slot 3	10	Network module slot 4

4	HWIC slot 2	11	Network module slot 2

5	HWIC slot 1	12	Network module slot 3

6	LED indicators	13	Network module slot 1

7	HWIC slot 0	14	Screw holes for grounding lug

Product Identification

The serial number for Cisco 3800 series routers is located near the right edge of the rear panel. Figure 9 shows the location on Cisco 3825 routers. Figure 10 shows the location on Cisco 3845 routers.

Figure 9 Cisco 3825 Router Serial Number Location

NMD-

ESW-

35x

GE1

10/100/1000

17x

FastEthernet Ports

Base-Tx

NM-

35x

17x

34x

ESW-

16x

33x

15x

32x

15x

14x

31x

FastEthernet Ports

13x

30x

12x

29x 11x

28x

18x

10x

27x 9x

26x 8x

Ext

25x

-48V

Pwr

24x

GE0

Ext

23x

22x

10/100/

21x 3x

1000

Pwr

20x 2x

Base-Tx

15x 7x

-48V

19x

14x

13x

10/100/

18x

12x

11x

1000

10x

Base-Tx

SN: XXXNNNNXXXX

121294 781-00282-01 C0

SN: XXXNNNNXXXX

Overview of Cisco 3800 Series Routers

	OL-5966-01	5

Built-In Ports

Figure 10 Cisco 3845 Router Serial Number Location

NM-

ESW-

15x

FastEth

ernet Ports

Ext

15x

Pwr

14x

-48V

13x

12x

10/100/

11x 3x

1000

10x

Base-

XXXNNNNXXXX SN:

SN: XXXNNNNXXXX

Note The serial number for Cisco 3825 and Cisco 3845 routers is 11 characters long.

121293, 781-00283-01 B0

Cisco Product Identification Tool

The Cisco Product Identification tool provides detailed illustrations and descriptions showing where to locate serial number labels on Cisco products. It includes the following features:

•A search option that allows browsing for models using a tree-structured product hierarchy

•A search field on the final results page making it easier to look up multiple products

•End-of-sale products are clearly identified in results lists

The tool streamlines the process of locating serial number labels and identifying products. Serial number information expedites the entitlement process and is important for access to support services.

The Cisco Product Identification tool can be accessed at the following URL:

http://tools.cisco.com/Support/CPI/index.do

Built-In Ports

Cisco 3800 series routers provide the following built-in ports:

•Two 1000BASE-T Gigabit Ethernet ports with RJ-45 connectors for shielded twisted pair. One of these ports provides a slot for an optional small-form-factor pluggable (SFP) module.

•One RJ-45 console port for connecting to a terminal.

•One RJ-45 auxiliary port for connecting to a modem.

•Two built-in USB 1.1 ports to support USB devices qualified and approved by Cisco. No approved USB devices are currently available, but enhancements are planned to provide additional flexibility and functionality.

•Cisco Redundant Power System connector (Cisco 3825 router only).

Overview of Cisco 3800 Series Routers

6	OL-5966-01

Module and Interface Card Capacity

Optional network modules and interface cards provide Cisco 3800 series routers with additional interfaces or functionality.

Network Modules

Network modules install directly into slots in the rear of the router. The Cisco 3845 router supports online insertion and removal (OIR, or hot swap) of network modules. The Cisco 3825 router does not support OIR.

Caution The Cisco 3845 router supports OIR with similar modules only. If you remove a network module, along with any installed WAN or voice interface cards, install another module and card combination exactly like it.

Caution The Cisco 3825 router does not support OIR of network modules. To avoid damaging the module, you must turn off electrical power and disconnect network cables before you insert the module into a router slot.

The Cisco 3825 router provides two slots for network modules. The lower network module slot of this router, labeled 1 on the rear panel, can hold either of the following sizes of network modules:

•One single-wide network module

•One extended single-wide network module

The upper network module slot of the Cisco 3825 router, labeled 2 on the rear panel, can hold any of the following sizes of network modules:

•One single-wide network module

•One extended single-wide network module

•One double-wide network module

•One extended double-wide network module

The Cisco 3845 router provides four slots for network modules, labeled 1, 2, 3, and 4 on the rear panel. Each slot can hold either of the following sizes of network modules:

•One single-wide network module

•One extended single-wide network module

Slots 1 and 2 can also be combined to hold either of the following sizes of network modules:

•One double-wide network module

•One extended double-wide network module

Slots 3 and 4 can be combined in the same way to hold one double-wide or extended double-wide network module.

Overview of Cisco 3800 Series Routers

	OL-5966-01	7

Module and Interface Card Capacity

Note The terms single-wide, extended single-wide, double-wide, and extended double-wide refer to the physical size of a network module. Enhanced network modules offer additional functionality; this functionality is not directly related to the module’s size.

Note The Cisco 3825 router supports one high-density analog-digital extension module for voice and fax. The Cisco 3845 module supports two of these modules.

Certain network module configurations require the installation or removal of a slot divider in the module slot. All configurations require blank faceplates or slot adapters to be installed over unused slots for cooling, electromagnetic interference (EMI) reduction, and safety. Procedures for installing network modules, slot dividers, slot adapters, and blank faceplates are described in “Installing Network Modules in Cisco 3800 Series Routers” and the Cisco Network Modules Hardware Installation Guide.

Interface Cards

Interface cards install either into slots in the rear of the router, or into slots in network modules. Interface cards come in the following types:

•WAN interface card (WIC)

•Voice interface card (VIC)

•Voice/data T1/E1 WAN interface card (VWIC)

•High-speed WAN interface card (HWIC)

Note You can insert any kind of interface card—WIC, VIC, VWIC, or HWIC—into a router HWIC slot. HWICs must be installed directly into router slots, not into network modules.

The Cisco 3825 router and the Cisco 3845 router each provide four interface card slots, labeled on the rear panel by HWIC and a number. Each slot can be occupied by one single-wide WIC, VIC, VWIC, or HWIC.

In addition, the HWIC 0 and HWIC 1 slots can be combined to hold one double-wide HWIC. The HWIC 2 and HWIC 3 slots can also be combined to hold one double-wide HWIC.

Note Although the HWIC 1 and HWIC 2 slots on the Cisco 3845 router are adjacent to each other, they cannot be combined to hold a double-wide HWIC.

The maximum capacity of Cisco 3800 series routers for interface cards inserted directly into the chassis is four WICs, VICs, VWICs, or HWICs, or two double-wide HWICs.

Caution Cisco 3800 series routers do not support OIR (hot swap) of interface cards inserted directly into router slots. You must turn off the router before installing or removing an interface card.

Overview of Cisco 3800 Series Routers

8	OL-5966-01

Port Numbering

Certain interface card configurations require the installation or removal of a slot divider in the router’s interface card slot. All slots must be covered by interface cards or blank faceplates for cooling, electromagnetic interference (EMI) reduction, and safety. Procedures for installing interface cards, slot dividers, and blank faceplates are described in “Installing Interface Cards in Cisco 3800 Series Routers” and the Cisco Interface Cards Installation Guide.

AIMS and PVDMs

Advanced integration modules (AIMs) and packet voice data modules (PVDMs) install into connectors on the router motherboard. AIMs provide hardware-based support for additional features. PVDMs are digital signal processor (DSP) SIMMs that provide voice support. The Cisco 3825 router and the Cisco 3845 router can each accommodate two AIMs and four PVDMs.

Installation, replacement, and removal of AIMs and PVDMs require opening the cover of the Cisco 3825 router, or removing the motherboard of the Cisco 3845 router. For more information, see “Installing and Upgrading Internal Components in Cisco 3800 Series Routers.”

Port Numbering

Each built-in network port on a Cisco 3800 series router, and each port or interface on a network module or interface card, is identified in Cisco IOS software by an interface type and a number or series of numbers separated by forward slashes (/). Port numbers for Cisco 3800 series routers follow the rules in this section.

Note Port numbering conventions differ for different router series. For routers that are not part of the Cisco 3800 series, consult your router documentation for port numbering information.

Built-In Ports

Cisco 3800 series routers have two Gigabit Ethernet ports built into the router’s rear panel, labeled 0/0 and 0/1. These numbers are used with the interface-type keyword gigabitethernet to identify the ports in Cisco IOS commands—gigabitethernet 0/0 and gigabitethernet 0/1.

Note If an optional SFP module is installed and selected, it is assigned gigabitethernet 0/0.

Network Module Ports

Ports on network modules inserted into a router slot are numbered slot/port, where slot is the slot number in the router and port is the port number in the network module. For example, port 1 of a Fast Ethernet network module inserted into router slot 2 would be identified as fastethernet 2/1.

The Cisco 3825 router has two slots for network modules. The lower slot is numbered 1 and the upper slot is numbered 2, as labeled on the router’s rear panel. (See Figure 4 on page 3.) The Cisco 3845 router has four slots: 1 at lower right, 2 at lower left, 3 at upper right, and 4 at upper left. (See Figure 8 on page 5.)

Overview of Cisco 3800 Series Routers

	OL-5966-01	9

Port Numbering

Note In the Cisco 3845 router, double-wide or extended double-wide network modules are identified by slot numbers 1 and 3.

Ports in a network module are normally numbered from right to left and bottom to top, starting at 0. See the Cisco Network Modules Hardware Installation Guide for more information.

Interface Card Ports

Interface cards can be inserted either directly into a router slot, or into a slot in a network module.

Interface Card in Router

Interface cards inserted directly into a router slot are numbered 0/HWIC-slot/port. HWIC-slot is the HWIC slot in the router—0, 1, 2, or 3, as labeled on the router’s rear panel; port is the port number in the interface card. For example, port 0 of a T1 WIC inserted into router HWIC slot 3 would be identified as t1 0/3/1.

Note Double-wide interface cards use HWIC slot numbers 1 and 3.

Ports in an interface card are normally numbered from right to left and bottom to top, starting at 0. See the Cisco Interface Cards Installation Guide for more information.

Interface Card in Network Module

Some network modules provide their own slots for interface cards. Ports in these interface cards are numbered router-slot/module-slot/port, where router-slot is 1 or 2 for the Cisco 3825 router and 1, 2, 3, or 4 for the Cisco 3845 router; module-slot is the slot in the network module for the interface card; and port is the port number in the interface card. For example, port 0 of a voice interface card in slot 1 of a voice network module in slot 4 of a Cisco 3845 router would be identified as voice 4/1/0.

Note Double-wide or extended double-wide network modules use router slot numbers 2 and 4.

Slots in network modules for interface cards are normally numbered from right to left, starting at 0. Ports in an interface card are normally numbered from right to left and bottom to top, starting at 0. For more information, see the Cisco Network Modules Hardware Installation Guide and Cisco Interface Cards Installation Guide.

Asynchronous Interface Numbering

For Cisco 3825 and Cisco 3845 routers, interface numbering for asynchronous interfaces is the same as for other interfaces. Use the interface number to specify the asynchronous line. For example, the command to configure port 1 of a 2-port asynchronous/synchronous WAN interface card in router HWIC slot 3 is interface serial 0/3/1. The command to configure the line associated with this port is line 0/3/1.

Similarly, line 1/22 specifies the line associated with interface async 1/22 on a 32-port asynchronous network module in router slot 1.

Overview of Cisco 3800 Series Routers

10	OL-5966-01

Memory

Cisco 3800 series routers contain the following types of memory:

•Main memory consists of ECC DDR SDRAM. It stores the running configuration and routing tables, and buffers packets at the network interfaces. Both routers ship with 256 MB of main memory. The two DIMM slots can be upgraded with 128-MB, 256-MB, or 512-MB DIMMs to a maximum of 1024 MB (1 GB).

•An external CompactFlash memory card stores the Cisco IOS software image. The routers are shipped with a 64-MB CompactFlash memory card, which can be upgraded to 128 MB or 256 MB.

•The routers boot from 4 MB of internal flash memory. This memory cannot be upgraded.

Power

Table 1 summarizes power options for Cisco 3800 series routers. Both the Cisco 3825 router and the Cisco 3845 router support an AC input power supply, an AC input power supply with IP phone power output, or a DC input power supply. The Cisco 3825 router has one internal power supply and also provides a connector for the optional Cisco Redundant Power System (RPS) external backup power source. The Cisco 3845 router supports two internal power supplies and operates in redundant mode both are installed.

Table 1	Cisco 3800 Series Routers Power Options

Router		Power Option	Input	IP Phone Power Output

Cisco 3825		AC input without IP phone power	100–240 VAC, 3 A	None
		output

		AC input with 24 ports of IP phone	100–240 VAC, 8 A	–48 VDC, 360 W
		power output

		DC input without IP phone power	24–60 VDC, 12 A	None
		output

		Cisco Redundant Power System	100 VAC, 10 A	If supported by router power supply
			240 VAC, 6 A

Cisco 3845		AC input without IP phone power	100–240 VAC, 5 A	None
		output

		AC input with 48 ports of IP phone	100–240 VAC, 9 A	–48 VDC, 360 W
		power output

		DC input without IP phone power	24–60 VDC, 19 A	None
		output

		Second internal power supply	Any option above

Overview of Cisco 3800 Series Routers

	OL-5966-01	11

LED Indicators

LEDs can help you monitor your router’s performance and operation by providing power, activity, and status information. For an explanation of LED activity during power-up, see the “Verifying LED Indications” section on page 34 of “Powering Up Cisco 3800 Series Routers.” To use LEDs for troubleshooting, see Table 1 in “Troubleshooting Cisco 3800 Series Routers.”

For descriptions of LEDs on network modules or interface cards, see the Cisco Network Modules Hardware Installation Guide and the Cisco Interface Cards Installation Guide.

Ventilation

Three internal multispeed fans cool the routers, controlled by a temperature sensor. At ambient temperatures below 40 degrees C, they operate at low speed to conserve power and reduce noise. At 40 degrees C or above they operate at high speed. The power supply has its own integrated fan.

Note On the Cisco 3825 router, when the router is installed with a Inline Power (ILP) power supply, the internal multispeed fans will operate at high speed only. To verify the fan speed, use the show environment command.

Real-Time Clock and Battery

An internal real-time clock (RTC) with battery backup allows the routers to check the validity of the certification authority (CA) certificate. The RTC is accurate under the operating environmental conditions specified for the router.

The clock and battery are permanently installed. Under the specified operating environmental conditions, the battery lasts the life of the router and does not need to be replaced.

Technical Specifications

Table 2 and Table 3 list Cisco 3800 series system specifications.

Table 2	Cisco 3825 Router Specifications

Specification		Value

Dimensions (H x W x D)		3.5 x 17.1 x 14.7 in. (8.9 x 43.4 x 37.3 cm)
		2 rack unit height

Weight (minimum)		23 lb (10.5 kg)

Overview of Cisco 3800 Series Routers

12	OL-5966-01

Technical Specifications

Table 2		Cisco 3825 Router Specifications	(continued)

Specification			Value

AC input power
•	Input voltage		100–240 VAC, autoranging
•	Frequency		47–63 Hz
•	Input current		3 A (8 A for IP phone support) at 110 V
			2 A (4 A for IP phone support) at 230 V
•	Inrush surge current		50 A maximum, one cycle
			(–48V IP phone power included)

DC input power
•	Input voltage		24–60 VDC, positive or negative, autoranging
•	Input current		12 A at 24 V; 5 A at 60 V
•	Inrush surge current		50 A maximum, <10 ms

Power dissipation
(maximum)
•	AC without		300 W (1025 BTU/hr)
	IP phone support

•AC with

IP phone support:

–	System only	370 W (1260 BTU/hr)
–	IP phones	360 W (1230 BTU/hr)
• DC		325 W (1110 BTU/hr)

Console and auxiliary ports		RJ-45 connector

Operating temperature		32 to 104°F (0 to 40°C)

Nonoperating temperature		–40 to 185°F (–40 to 85°C)

Operating humidity		5–95%, noncondensing

Operating altitude		Up to 6,500 ft (2,000 m); derate temperature 1°C per
		1,000 ft

Noise level		50 dBA typical, 53 dBA maximum

Regulatory compliance		FCC Part 15 Class A. For additional compliance
		information, see the Cisco 2800 Series and Cisco 3800
		Series Integrated Services Routers Regulatory
		Compliance and Safety Information document that
		accompanied the router.

Safety compliance		UL 60950; CAN/CSA C22.2 No. 60950-00;
		EN 60950; AS/NZS 3260

Overview of Cisco 3800 Series Routers

	OL-5966-01	13

Technical Specifications

Table 3		Cisco 3845 Router Specifications

Specification			Value

Dimensions (H x W x D)			5.25 x 17.25 x 16.0 in. (13.3 x 43.8 x 40.6 cm)
			3 rack unit height

Weight (minimum)			45 lb (20 kg)

AC input power
•	Input voltage		100–240 VAC, autoranging
•	Frequency		47–63 Hz
•	Input current		4 A (8 A for IP phone support) at 110 V
			2 A (4 A for IP phone support) at 230 V
•	Inrush surge current		50 A maximum, one cycle (–48V IP phone power
			included)

DC input power
•	Input voltage		24–60 VDC, positive or negative, autoranging
•	Input current		18 A at 24 V; 7 A at 60 V
•	Inrush surge current		50 A maximum, <10 ms

Power dissipation
(maximum)
•	AC without		435 W (1485 BTU/hr)
	IP phone support

•AC with

IP phone support:

–	System only	555 W (1890 BTU/hr)
–	IP phones	360 W (1230 BTU/hr)
• DC		460 W (1570 BTU/hr)

Console and auxiliary ports		RJ-45 connector

Operating temperature		32 to 104°F (0 to 40°C)

Nonoperating temperature		-40 to 185°F (-40 to 85°C)

Operating humidity		5–95%, noncondensing

Operating altitude		Up to 6,500 ft (2,000 m); derate 1°C per 1,000 ft

Noise level		56 dBA typical, 58 dBA maximum

EMC compliance		FCC Part 15 Class A. For additional compliance
		information, see the Cisco 2800 Series and Cisco 3800
		Series Integrated Services Routers Regulatory
		Compliance and Safety Information document.

Safety compliance		UL 60950; CAN/CSA C22.2 No. 60950-00;
		EN 60950; AS/NZS 3260. For additional compliance
		information, see the Cisco 2800 Series and Cisco 3800
		Series Integrated Services Routers Regulatory
		Compliance and Safety Information document.

Overview of Cisco 3800 Series Routers

14	OL-5966-01

Regulatory Compliance

For complete regulatory compliance information, see the Cisco 2800 Series and Cisco 3800 Series Integrated Services Routers Regulatory Compliance and Safety Information document that accompanied the router.

Overview of Cisco 3800 Series Routers

	OL-5966-01	15

Regulatory Compliance

Overview of Cisco 3800 Series Routers

16	OL-5966-01

+ 108 hidden pages

Cisco Product	Document

Cisco 3800 series routers	Cisco 3800 Series Integrated Services Routers Quick Start Guide

	Cisco 3800 Series Software Configuration

	Cisco 3800 Series Cards and Modules

	Cisco 2800 Series and Cisco 3800 Series Integrated Services Routers
	Regulatory Compliance and Safety Information

	Quick Start Guide: Network Modules for Cisco Access Routers

	Cisco Network Modules Hardware Installation Guide

	Quick Start Guide: Interface Cards for Cisco Access Routers

	Cisco Interface Cards Installation Guide

	Cisco Modular Access Router Cable Specifications

	Cisco RPS-675 Redundant Power System Hardware Installation Guide

Network management	Network management software documentation
system

Cisco IOS software	Cisco IOS software documentation, all releases
	Refer to documentation for the Cisco IOS software release installed on
	your router.