AV Receiver
Easy Setup Guide
English for U.S.A.
This document explains how to set up a 5.1- or 7.1-channel system and play back surround sound of a BD/DVD on this unit.
For more information, refer to “Owner’s Manual” on the supplied CD-ROM.
A PDF format of this guide and “Owner’s Manual” can be downloaded from the following website. http://download.yamaha.com/
Check that the following accessories are supplied with this product.
■ Remote control |
■ Batteries (AAA, R03, UM-4) (x 2) |
|
Insert into the remote control in the correct polarity (+/-). |
■ YPAO microphone |
■ VIDEO AUX input cover |
■ AM antenna |
■ FM antenna |
■ CD-ROM |
■ Safety Brochure |
■ Easy Setup Guide |
||||||||||||||||||
|
(Owner’s Manual) |
|
|
|
|
|
|
|
(this document) |
|||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
You need to separately prepare the following cables to build the system based on this document.
■Speaker cables (depending on the number of speakers)
■HDMI cable (x 2)
■Audio pin cable (x 1)
■Digital optical cable (x 1) (unnecessary if your TV supports ARC)
Set up the speakers in the room by using the following diagram as a reference.
For information on other speaker systems, refer to “Owner’s Manual”.
5.1-channel system |
7.1-channel system |
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
60° 60°
80° 80°
30 cm (1 ft) or more
60° 60°
Front speaker (L)
Front speaker (R)
80° 80°
Center speaker
Surround speaker (L)
Surround speaker (R)
Surround back speaker (L)
Surround back speaker (R)
Subwoofer
2En
•This unit is configured for 8-ohm speakers at the factory. When
connecting 6-ohm speakers, set the speaker impedance of this unit to “6 Ω MIN”. For details, see “Setting the speaker impedance” (p.16) in “Owner’s Manual”.
•Use a subwoofer equipped with built-in amplifier.
•Remove the power cable of this unit from an AC wall outlet and turn off the subwoofer before connecting the speakers.
•Be careful that the core of the speaker cable does not touch anything or come into contact with the metal areas of this unit. This may damage this unit or the speakers. If the speaker cables short circuit, “CHECK SP WIRES” will appear on the front display when this unit is turned on.
Connecting speaker cables
Speaker cables have two wires. One is for connecting the negative (-) terminal of the unit and the speaker, and the other is for the positive (+) terminal. If the wires are colored to prevent confusion, connect the black wire to the negative and the other wire to the positive.
1 Remove approximately |
|
10 mm of insulation from |
+ (red) |
the ends of the speaker |
|
cable, and twist the bare |
|
wires of the cable |
|
together firmly. |
– (black) |
2 Loosen the speaker |
|
terminal. |
|
3Insert the bare wires of the cable into the gap on the side (upper right or bottom left) of the terminal.
4 Tighten the terminal.
Using a banana plug
1 Tighten the speaker
terminal.
Banana plug
2 Insert a banana plug into the end of the terminal.
1Connect the front speakers (/) to the FRONT (/) terminals.
This unit (rear) |
|
|
|
|
|
|
|
SPEAKERS |
|
|
|
R FRONT L |
CENTER |
R SURROUND L |
SURROUND BACK/BI–AMP |
|
|
|
|
R |
L |
|
|
|
|
|
SINGLE |
|
|
|
|
|
R |
L |
EXTRA SP |
|
|
|
|
|
ZONE 2/ |
|
|
|
|
|
PRESENCE |
|
|
|
SUBWOOFER |
|
|
2Connect the center speaker () to the CENTER terminal.
This unit (rear) |
|
|
|
|
|
|
|
SPEAKERS |
|
|
|
R FRONT L |
CENTER |
R SURROUND L |
SURROUND BACK/BI–AMP |
|
|
|
|
R |
L |
|
|
|
|
|
SINGLE |
|
|
|
|
|
R |
L |
EXTRA SP |
|
|
|
|
|
ZONE 2/ |
|
|
|
|
|
PRESENCE |
|
|
|
SUBWOOFER |
|
|
En 3