TP-Link TL-SF2226P User Manual
COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a registered
trademark of TP-LINK Technologies Co., Ltd. Other brands and product names are
trademarks or registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used to
make any derivative such as translation, transformation, or adaptation without
permission from TP-LINK Technologies Co., Ltd. Copyright © 2005 TP-LINK
Technologies Co., Ltd. All rights reserved.
COPYRIGHT & TRADEMARKS ......................................................................... 0
Package Contents............................................................................................................. 1
Chapter 1: About this User's Guide ................................................................................... 2
1.1 Usage................................................................................................................... 2
1.2 Assumpsit............................................................................................................. 2
1.3 Overview of this User's Guide.............................................................................. 2
Chapter 2: Introduction...................................................................................................... 3
2.1 Features............................................................................................................... 3
Chapter 3: Installation ....................................................................................................... 4
3.1 Installation............................................................................................................ 4
3.2 Rack Installation................................................................................................... 4
3.3 Power On ............................................................................................................. 5
3.4 Initialization .......................................................................................................... 5
Chapter 4: Explanation of Switch Appearance and the Method of Connecting Switch...... 6
4.1 Front Panel .......................................................................................................... 6
4.2 Rear Panel ........................................................................................................... 6
4.3 LED...................................................................................................................... 7
4.4 Optional Extension Modules ................................................................................ 7
4.5 Connection........................................................................................................... 7
Chapter 5: Installation and the Usage of the Remote Management Software................... 8
5.1 Steps of Installation of the Remote Management Software —SSU...................... 8
5.2 Usage of Remote Configuration Software -- SSU ................................................ 8
5.2.1 Add............................................................................................................. 9
5.2.2 Connection............................................................................................... 13
5.2.3 Configuration ........................................................................................... 14
5.2.4 Exit........................................................................................................... 21
Chapter6 TELNET/Out-of-Band Management ................................................................ 22
6.1 Introduction ........................................................................................................ 22
6.2 How to connect Out-of-Band.............................................................................. 22
6.3 How to connect TELNET.................................................................................... 24
6.4 The interface and operating way of TELNET/Out-of-Band................................. 25
6.5 Configuration of Out-of-Band Management ....................................................... 25
Appendix A Technical Specifications ............................................................................... 33
TL-SF2226P+/TL-SL2226P+ Remote Smart Switch User Guide
Package Contents
The following contents should be found in your box:
One Switch
One AC power cable
One Serial cable
One User's Guide
One Resource CD
Two mounting brackets and screws
Note: If any of the listed contents are damaged or missing, please contact the retailer
from whom you purchased the Switch for assistance.
- 1 -
TL-SF2226P+/TL-SL2226P+ Remote Smart Switch User Guide
Chapter 1: About this User's Guide
Thank you for purchasing TL-SF2226P+/TL-SL2226P+ Remote Smart Switch! The
TL-SF2226P+/TL-SL2226P+ provides powerful management functions. With the feature
of high-performance, easy to use and economical, the TL-SF2226P+/TL-SL2226P+ is
one of the best choice for you.
1.1 Usage
This User's Guide tells you how to use the TL-SF2226P+/TL-SL2226P+ Remote Smart
Switch.
1.2 Assumpsit
The Switch indicated in the User's Guide is the TL-SF2226P+/TL-SL2226P+ Remote
Smart Switch.
1.3 Overview of this User's Guide
Chapter 1 About the User's Guide
Chapter 2 Introduction. Describes the switch and its features
Chapter 3 Installation. Helps you to get started with the basic installation of the switch
Chapter4 Explanation of switch appearance and the method of connecting switch
Chapter5 Installation and Usage of Remote Management Software
Chapter6 TELNET/Out-of-Band Management
Appendix Technical Specifications
- 2 -
TL-SF2226P+/TL-SL2226P+ Remote Smart Switch User Guide
Chapter 2: Introduction
This part simply describes the features of TL-SF2226P+/TL-SL2226P+ Remote Smart
Switch. For more details, please refer to Chapter 4.
2.1 Features
Supports remote management
Supports Out-of-Band management
Supports Telnet management
Provides 10/100M switch base function
24 10Base-T/100Base-TX RJ-45 ports with auto-MDI/MDIX
The TL-SL2226P+ provides two 10Base-T/100Base-TX/1000Base-T, 100Base-FX/
1000Base-SX/LX extension slots, supporting 10/100/1000Mbps module card, e.g.
TL-SM201/TL-SM301 serial fiber/twist pair module card.
The TL-SF2226P+ provides two independent extension slots, supporting
10/100Mbps module card, e.g. TL-SM201 serial fiber/twist pair module card.
Supports port auto-negotiation function, negotiating the speed and duplex mode
between the devices automatically
Supports full-duplex/half-duplex flow control
Provides Maximum 26 Port-based VLAN and 32 IEEE802.1Q based Tag VLAN
Supports MAC address learning and aging with programmable age time
Supports MAC Binding.
Supports QOS configuration (802.1p Base QOS)
Supports Trunk management.
Supports bandwidth Management
Supports upgrading switch software with COM and TFTP
- 3 -
TL-SF2226P+/TL-SL2226P+ Remote Smart Switch User Guide
Chapter 3: Installation
3.1 Installation
Follow these steps to install the switch:
The surface must support at least 5kg
The power source must be within 1.5m
Check the cable to make sure the connection to AC power
Leave enough space for the ventilation
3.2 Rack Installation
The TL-SF2226P+/TL-SL2226P+ can be mounting in an EIA standard size 19 inches
rack.
1. Attach a mounting bracket to each side of the TL-SF2226P+ with the screws
provided.
2. Slide the TL-SF2226P+/TL-SL2226P+ into the Rack.
3. Use the screws to secure the switch to the Rack.
Figure 3-1 The view of attaching the mount brackets on the TL-SF2226P+
- 4 -
TL-SF2226P+/TL-SL2226P+ Remote Smart Switch User Guide
Figure 3-2 The view of mounting the TL-SF2226P+ in the rack
3.3 Power On
The TL-SF2226P+/TL-SL2226P+ can be used with the power source in the range of 100
to 240 VAC, 50 to 60Hz.
The internal power system of the TL-SF2226P+/TL-SL2226P+ can automatically adjust
the operating power according to the power input. The POWER LED will be light when
power on.
3.4 Initialization
Turn on the power, the switch will automatically initialize and the LEDs will be light as
follows:
At the time you turn on the power, if the LEDs of slot1 and slot2 on the front panel are
light, which means there are two module cards in slot1 and slot2. The LEDs of Port 1- 24
will turn out after two seconds that indicates the system is resetting. The CUP LED
flashing means the switch starts to work in good condition.
Caution: As a precaution in the event of a power failure, unplug the switch. When the
power resumed, plug the switch back in.
All the pictures are based on the TL-SF2226P+ in the manual. The pictures of
TL-SL2226P+ are almost the same as TL-SF2226P+.
- 5 -
TL-SF2226P+/TL-SL2226P+ Remote Smart Switch User Guide
Chapter 4: Explanation of Switch Appearance and the Method of Connecting Switch
This chapter covers more details about front panel, rear panel, LED and extension
module of the switch.
4.1 Front Panel
There are 24 10/100Mbps ports and LED indicators on the front panel of the
TL-SF2226P+.
1357
2468
9111315
10 12 14 16
17 19 21 23
18 20 22 24
Figure 4-1 Front Panel of the TL-SF2226P+
4.2 Rear Panel
Console
TX RX TX RX
Figure 4-2 Rear Panel of the TL-SF2226P+
There is a power switch, a power connector, a console (RS232) port and 2 extension
module slots on the rear panel.
Power Connector
The AC power connector is a standard three-pronged connector that supports the power
cord. Plug the female connector of the provided power cord into the socket, and the male
side of the cord into a power outlet. Supported input voltage range is from 100 to 240
VAC at 50-60Hz.
Slot 2Slot 1
110-260V 50-60Hz 0.6A
Console Port
The console port or RS232 port on the right of the rear panel is the connection port with
PC when Out-of-Band management. (For more details, please refer to Chapter 6).
Module Slot
The module slots can be inserted with 10/100M module card (TL-SF2226P+) or
10/100/1000M or a 1000M Base-X module card (TL-SL2226P+).
- 6 -
TL-SF2226P+/TL-SL2226P+ Remote Smart Switch User Guide
4.3 LED
LEDs, including Power LED, 100Mbps LED, Link/Act LED, Slot1, Slot2 and CPU LED,
can detect and indicate the state of the switch. More details are as follows.
1357
2
6
4
8
9111315
10 12 14 16
17
19 21 23
18 20 22 24
Figure 4-3 LED Indicators view of TL-SF2226P+ Switch
Power LED
The power LED will be solid red when power on, or else, check the power connection.
Link/Act LED
The LED is lit when there is a secure connection to a device at any of the ports.
100Mbps LED
When the normal ports connect a 100Mbps device, the corresponding LED is green, an
unlit LED indicates a connection speed of 10Mbps.
Slot LED
Slot1, Slot2 LED indicates that whether there is a module card in the module slot.
CPU LED
The CPU LED flashing means that the switch works in good condition.
4.4 Optional Extension Modules
Before you install any modules, remember to turn off the power at first.
After you take out the board on the slot, put the module into the extension slot. The
TL-SF2226P+ can auto-identify the module and configure it automatically.
The TL-SF2226P+ can be used with TL-SM201 100M series modules.
Caution: Never install the modules without turning off the power.
4.5 Connection
The TL-SF2226P+ supports MDI/MDIX, so you can use every port as a normal port or an
uplink port. Each port is independent, which makes the connection very easy.
Caution: When the connection is ok, the Link/Act is light, or else, make sure the twist
pair is working and the power is on.
- 7 -
TL-SF2226P+/TL-SL2226P+ Remote Smart Switch User Guide
Chapter 5: Installation and the Usage of the Remote Management Software
The TL-SF2226P+/TL-SL2226P+ is a smart switch, you can configure it with the remote
Management software shipped with the switch, It’s very convenient for you to manage
the switch. After install the software under windows OS, you can manage several
switches at the same time.
Caution: Between the remote management software and the telnet management
described in the next chapter, you can only choose one to manage the switch.
5.1 Steps of Installation of the Remote Management Software —SSU
1) Installation requirement: Windows OS, Supporting TCP/IP Protocol.
2) Installation steps: Run the setup.exe, and following the wizard to finish the setup. If
you want to change the default path, click Browse, Input or choose the path you
want, click OK and then next to finish the setup. As figure 5-1.
Figure 5-1
5.2 Usage of Remote Configuration Software -- SSU
The interface of SSU application is friendly and easy to use. Generally speaking, there
- 8 -
TL-SF2226P+/TL-SL2226P+ Remote Smart Switch User Guide
are four steps on configuring the switch.
1) Add
2) Connection
3) Configuration
4) Exit
Caution: When you use the switch for the first time, you must reset the IP address and
gateway of the switch. The witch default IP address is 192.168.0.100(for more details,
please refer to Chapter 5).
Here are details on how to use the SSU application.
Before configuration, make sure that the PC and the switch which the SSU application
installed can see each other. You can ping the switch, check whether they can see each
other. If they can't see each other, check whether the power is on and the twisted pair is
well connected. If all is ok, run the SSU application, you can see the initialized interface
of the SSU application. As figure 5-2.
Figure 5-2
5.2.1 Add
1) First, add a device group. The name of the new group can't be the same as the
names that already existed in the application. After adding the group, you can
rename the group and delete it at any time. Here are some methods as follows.
a) Click main menu->System->Add Group. As figure 5-3.
- 9 -
Loading...