Tekmar 087, 087_D Installation & Operation Manual
Wireless Outdoor Sensor 087
Installation & Operation Manual
087_D
05/16
Accessories
Replaces: New
© 2016 087_D - 05/16
1 of 8
A Watts Water Technologies Company
The tekmar Wireless Outdoor Sensor 087 provides a simple solution to include outdoor
temperature measurement in any application without exterior wiring. The transmitter
and receiver are sold pre-linked and are installation-ready. With exceptional range
and an 8 year battery life, the Wireless Outdoor Sensor 087 provides maximum
accuracy, convenience and reliability.
Features
Wireless Outdoor Sensor 087
Receiver
Communication
Power
Low Battery
Link
• Compatible with all tekmar controls and
thermostats as well as other manufacturers
products
•
10K (type 2 and 3), 5K, 12K and 20K
resistance setting options
• Low transmitter battery status indicator
on the receiver
•
Power and communication indicator lights
• Transmitter temperature range of
-40°F to 140°F (-40°C to 60°C)
•
Long battery life (minimum 8 years) with
included 1.5V Lithium AA batteries
• 5000 ft. open range
• 8 walls / 250 ft. indoor range
© 2016 087_D - 05/16
2 of 8
To avoid serious personal injury and damage to the equipment:
It is your responsibility to ensure that this control is safely installed
according to all applicable codes and standards. tekmar is not responsible
for damages resulting from improper installation and/or maintenance.
•
Read Manual and all product labels BEFORE using the equipment.
Do not use unless you know the safe and proper operation of this
equipment.
• Keep this Manual available for easy access by all users.
• Replacement Manuals are available at tekmarControls.com
• Disconnect all power before opening the control.
•
Do not attempt to service the control. There are no user serviceable
parts inside the control. Attempting to do so voids warranty.
FCC ID: 2AHQR-10850A IC ID: 21247-10850A
FCC: This product has been tested and found to comply with FCC part 15 subpart C. Operation is subject to the following two
conditions: (1) this device may not cause Harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation of the device. However, there is no guarantee that interference
will not occur in a particular installation. If this device does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on. The user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
Industry Canada: This Device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to
the following two conditions: 1) this device may not cause interference, and 2) this device must accept any interference,
including interference that may cause undesired operation of the device under Industry Canada regulations.
Warning: FCC and IC Radiation Exposure Statement
The Transmitter device must provide a separation distance of at least 20 cm (8 chines) from all persons and must not be
co-located or operating in conjunction with any other antenna or transmitter.
© 2016 087_D - 05/16
3 of 8
Check the contents of this package. If any of the contents listed are missing or
damaged, please refer to the Limited Warranty and Product Return Procedure on
the back of this brochure and contact your wholesaler or tekmar sales representative
for assistance.
• One Receiver Unit (for indoor installation) • One Transmitter Unit (for outdoor
installation) • 2 1.5V AA Lithium batteries • Installation hardware • One Installation
& Operation Manual
When choosing the location for the receiver unit, consider the following:
• Interior Wall.
• Keep dry. Avoid potential leakage onto the unit.
• Relative Humidity less than 90%. Non-condensing environment.
• No exposure to extreme temperatures beyond 32 to 122°F (0 - 50°C)
• Away from equipment, appliances, or other sources of electrical interference.
• Easy access for wiring
• Approximately 5 feet (1.5 m) off the finished floor.
• DO NOT mount the transmitter or receiver in a metal enclosure, or on a
surface with conductive properties. It will reduce the signal strength and
affect the communication distance and reliability.
Step 2 - Install receiver
Step 1 - Check the Contents
Grasp the front cover by the fingertip
grips on the top and bottom of the
enclosure and pull the front cover off.
Remove the wiring cover screw.
The enclosure is either mounted flush
onto a wall or it can be placed onto a 2"
x 4" electrical box. The mounting holes
in the enclosure accept #6 screws.
Wiring to the control enters the wiring
chamber through the back or bottom of
the enclosure.
Loading...