PC board shown are viewed from parts side.
The parts with no reference number or no parts number
in the exploded views are not supplied.
As regards the resistors and capacitors, refer to the
circuit diagrams contained in this manual.
!
Parts marked with this sign are safety critical
components. they must be replaced with identical
components - refer to the appropriate parts list and
ensure exact replacement.
Parts of [ ] mark can be used only with the version designated.
[T/C]: USA [E]: Europe
AM/FM STEREO DIGITAL
RADIO WITH CD PLAYER
1 SAFETY INFORMATION
2 SPECIFICATIONS
3 ADJUSTMENT AND CHECKS
4 EXPLODED VIEW AND PARTS LIST
5 PC BOARDS AND PARTS LISTS
6 WIRING DIAGRAM
7 INCLUDED ACCESSORIES
2
3
4
6
9
15
17
SX
1 SAFETY INFORMATION
SAFETY INFORMATION
This product has been designed and manufactured according to FDA regulations " title 21, CFR, chapter 1,subchapter J,based on
The Radiation Control for Health and Safety Act of 1968" and is classified as class 1 laser product. There is not hazardous
invisible laser radiation during operation because invisible laser radiation emitted inside of this product is completely confined
in the protective housings. The label required in this regulation is shown .
CAUTION
USE OF CONTROLS OR ADJUSTMENT OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY
HAZARDOUS RADIATION EXPOSURE.RESULT IN
DO NOT REMOVE THE PROTECTIVE HOUSING USING SCREWDRIVER.
IF THIS PRODUCT DEVELOPS TROUBLE, MAKE A CONTACT WITH OUR SERICEMAN, AND DO NOT USE THE PRODUCT A TROUBLED
STATE.
1
Opt ical pi ckup:
Type : C MS-B3 5BG6
Man ufact urer : Sa msung E lectr o-Mec hanic
Las er outp ut : Less t han 0.5 m W on the ob jecti ve lens
Wavelength : 760 - 800 nm
1
FOR U. S.A.
2
TUNER SECTION
SX
2 SPECIFICATIONS
Frequency Range (FM):
Frequency Range (AM):
CD PLAYER Section
Frequency response :
Wow and Flutter:
SPEAKER SYSTEM Section
Type :
Impedance :
GENERAL
Total Output Power:
Power Requirements:
Power Consumption:
Dimension (W x H x D ):
Weight: (net)
87.5MHz to 108.00 MHz (100kHz step) - USA
87.5MHz to 108.00 MHz (50kHz step) - EUR
520kHz to 1710 kHz (10kHz step) - USA
522kHz to 1620 kHz (9kHz step) - EUR
20 Hz ~ 20 kHz (+/- 2 dB)
Unmeasurable
65mm x 2
4 ohms
4 W + 4 W
120V , 60Hz (U.S.A./ Canada model)
230V , 50Hz (Europe model)
28 W
340 x 125 x 249 mm
3.5 kg
Standard Accessories:
Design and specifications are subject to change without notice.
Illustrations may differ slightly from production models.
Remote Control Unit (RC-1031) x1
Battery for Remote Control x 1
Stereo mini plug cable x 1
,
Owner s Manual x 1
Warranty Card x 1
3
SX
3 ADJUSTMENTS AND CHECKS
3-1 TUNER SECTION
Use a screwdriver with a plastic or ceramic grip for all adjustment.
3-1-1 FM adjustment
1. Set the function switch to the FM position.
2. Connect the signal generator output through a 75 ohm dummy
antenna to "ANT" on MAIN PCB.
3. Connect the oscilloscope to the speaker terminal.
4. Set the signal generator as listed in the alignment chart.
3-1-2 AM adjustment
1. Set the function switch to the AM position.
2. Connect the test loop antenna across the output of the signal generator.
3. Connect the oscilloscope to the speaker terminal.
4. Set the signal generator as listed in the alignment chart.