Rockwell Automation 2080-LC30-10QWB, 2080-LC30-10QVB User Manual

Installation Instructions

Micro830 10 Point Programmable Controllers

Catalog Numbers 2080-LC30-10QWB, 2080-LC30-10QVB

http://rockwellautomation.com/literature

Cette publication est disponible en français
sous forme électronique (fichier PDF). Pour la

FR

télécharger, rendez-vous sur la page Internet
indiquée ci-dessus.
Questa pubblicazione è disponibile in Italiano
in formato PDF. Per scaricarla collegarsi al sito

IT

Web indicato sopra.

Diese Publikation ist als PDF auf Deutsch
verfügbar. Gehen Sie auf die oben genannte

DE

Web-Adresse, um nach der Publikation zu
suchen und sie herunterzuladen.
Esta publicación está disponible en español
como PDF. Diríjase a la dirección web indicada

ES

arriba para buscar y descarga esta publicación.

Table of Contents

Topic Page

Important User Information 2

Additional Resources 6

Overview 7

Controller Description 7

Status Indicators 8

Mount the Module 8

Wire the Controller 11

Specifications 13

Esta publicação está disponível em portugués
como PDF. Vá ao endereço web que aparece

PT

acima para encontrar e fazer download da
publicação.

ZH

ZC

KO

2 Micro830 10 Point Programmable Controllers

IMPORTANT

Important User Information

Solid state equipment has operational characteristics differing from those of electromechanical equipment. Safety Guidelines
for the Application, Installation and Maintenance of Solid State Controls (Publication SGI-1.1
Automation sales office or online at http://rockwellautomation.com/literature
solid state equipment and hard-wired electromechanical devices. Because of this difference, and also because of the wide
variety of uses for solid state equipment, all persons responsible for applying this equipment must satisfy themselves that each
intended application of this equipment is acceptable.
In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the use
or application of this equipment.
The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and
requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or liability for
actual use based on the examples and diagrams.
No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or software
described in this manual.
Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation, Inc., is
prohibited.
Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

WARNING: Identifies information about practices or circumstances that can cause an explosion in a
hazardous environment, which may lead to personal injury or death, property damage, or economic
loss.

ATTENTION: Identifies information about practices or circumstances that can lead to personal injury
or death, property damage, or economic loss. Attentions help you identify a hazard, avoid a hazard and
recognize the consequences.

SHOCK HAZARD: Labels may be on or inside the equipment (for example, drive or motor) to alert
people that dangerous voltage may be present.

BURN HAZARD: Labels may be on or inside the equipment (for example, drive or motor) to alert
people that surfaces may reach dangerous temperatures.

IMPORTANT: Identifies information that is critical for successful application and understanding of the
product.

) describes some important differences between

available from your local Rockwell

Publication 2080-IN002B-EN-P - April 2014

Environment and Enclosure

ATTENTION: This equipment is intended for use in a Pollution Degree 2

industrial environment, in overvoltage Category II applications (as defined in
IEC 60664-1), at altitudes up to 2000 m (6562 ft) without derating. This
equipment is considered Group 1, Class A industrial equipment according to
IEC/CISPR 11. Without appropriate precautions, there may be difficulties with
electromagnetic compatibility in residential and other environments due to
conducted and radiated disturbances.

This equipment is supplied as open-type equipment. It must be mounted
within an enclosure that is suitably designed for those specific environmental
conditions that will be present and appropriately designed to prevent personal
injury resulting from accessibility to live parts. The enclosure must have
suitable flame-retardant properties to prevent or minimize the spread of
flame, complying with a flame spread rating of 5V A, V2, V1, V0 (or equivalent)
if non-metallic. The interior of the enclosure must be accessible only by the
use of a tool. Subsequent sections of this publication may contain additional
information regarding specific enclosure type ratings that are required to
comply with certain product safety certifications.

In addition to this publication, see:

• Industrial Automation Wiring and Grounding Guidelines, Rockwell
Automation publication 1770-4.1

• NEMA Standard 250 and IEC 60529, as applicable, for explanations of the
degrees of protection provided by different types of enclosure.

Micro830 10 Point Programmable Controllers 3

, for additional installation requirements.

Preventing Electrostatic Discharge

ATTENTION: This equipment is sensitive to electrostatic discharge, which

can cause internal damage and affect normal operation. Follow these
guidelines when you handle this equipment:

• Touch a grounded object to discharge potential static.

• Wear an approved grounding wriststrap.

• Do not touch connectors or pins on component boards.

• Do not touch circuit components inside the equipment.

• Use a static-safe workstation, if available.

• Store the equipment in appropriate static-safe packaging when not in use.

Publication 2080-IN002B-EN-P - April 2014

4 Micro830 10 Point Programmable Controllers

North American Hazardous Location Approval

The following modules are North American Hazardous Location approved:
2080-LC30-10QWB, 2080-LC30-10QVB

The following information applies when
operating this equipment in hazardous
locations:

Products marked "CL I, DIV 2, GP A, B, C, D" are
suitable for use in Class I Division 2 Groups A, B,
C, D, Hazardous Locations and nonhazardous
locations only. Each product is supplied with
markings on the rating nameplate indicating the
hazardous location temperature code. When
combining products within a system, the most
adverse temperature code (lowest "T" number)
may be used to help determine the overall
temperature code of the system. Combinations
of equipment in your system are subject to
investigation by the local Authority Having
Jurisdiction at the time of installation.

WARNING: EXPLOSION
HAZARD

• Do not disconnect equipment
unless power has been removed or
the area is known to be
nonhazardous.

• Do not disconnect connections to
this equipment unless power has
been removed or the area is known
to be nonhazardous. Secure any
external connections that mate to
this equipment by using screws,
sliding latches, threaded
connectors, or other means
provided with this product.

• Substitution of any component may
impair suitability for Class I,
Division 2.

• If this product contains batteries,
they must only be changed in an
area known to be nonhazardous.

Informations sur l’utilisation de cet
équipement en environnements
dangereux:

Les produits marqués "CL I, DIV 2, GP A, B, C,
D" ne conviennent qu'à une utilisation en
environnements de Classe I Division 2 Groupes
A, B, C, D dangereux et non dangereux.
Chaque produit est livré avec des marquages
sur sa plaque d'identification qui indiquent le
code de température pour les environnements
dangereux. Lorsque plusieurs produits sont
combinés dans un système, le code de
température le plus défavorable (code de
température le plus faible) peut être utilisé
pour déterminer le code de température global
du système. Les combinaisons d'équipements
dans le système sont sujettes à inspection par
les autorités locales qualifiées au moment de
l'installation.

AVERTISSEMENT: RISQUE
D’EXPLOSION

• Couper le courant ou s'assurer
que l'environnement est classé
non dangereux avant de
débrancher l'équipement.

• Couper le courant ou s'assurer
que l'environnement est classé
non dangereux avant de
débrancher les connecteurs. Fixer
tous les connecteurs externes
reliés à cet équipement à l'aide
de vis, loquets coulissants,
connecteurs filetés ou autres
moyens fournis avec ce produit.

• La substitution de tout composant
peut rendre cet équipement
inadapté à une utilisation en
environnement de Classe I,
Division 2.

• S'assurer que l'environnement est
classé non dangereux avant de
changer les piles.

Publication 2080-IN002B-EN-P - April 2014

Micro830 10 Point Programmable Controllers 5

WARNING:

• When used in a Class I, Division 2, hazardous location, this equipment must be
mounted in a suitable enclosure with proper wiring method that complies with
the governing electrical codes.

• If you connect or disconnect the serial cable with power applied to this module
or the serial device on the other end of the cable, an electrical arc can occur.
This could cause an explosion in hazardous location installations. Be sure that
power is removed or the area is nonhazardous before proceeding.

• The local programming terminal port is intended for temporary use only and
must not be connected or disconnected unless the area is assured to be
nonhazardous.

• The USB port is intended for temporary local programming purposes only and
not intended for permanent connection. If you connect or disconnect the USB
cable with power applied to this module or any device on the USB network, an
electrical arc can occur. This could cause an explosion in hazardous location
installations. Be sure that power is removed or the area is nonhazardous before
proceeding.
The USB port is a nonincendive field wiring connection for Class I, Division2
Groups A, B, C and D.

• Exposure to some chemicals may degrade the sealing properties of materials
used in the Relays. It is recommended that the User periodically inspect these
devices for any degradation of properties and replace the module if
degradation is found.

• If you insert or remove the plug-in module while backplane power is on, an
electrical arc can occur. This could cause an explosion in hazardous location
installations. Be sure that power is removed or the area is nonhazardous before
proceeding.
Refer to the Wiring Diagram for each plug-in module for additional details
regarding removal or insertion under power.

ATTENTION:

• To comply with the CE Low Voltage Directive (LVD), this equipment must be
powered from a source compliant with the following: Safety Extra Low
Voltage (SELV) or Protected Extra Low Voltage (PELV).

• To comply with UL restrictions, this equipment must be powered from a
Class 2 or Limited Voltage Limited Current Source (LVLC).

Publication 2080-IN002B-EN-P - April 2014

6 Micro830 10 Point Programmable Controllers

ATTENTION:

• Be careful when stripping wires. Wire fragments that fall into the controller
could cause damage. Once wiring is complete, make sure the controller is
free of all metal fragments.

• Do not remove the protective debris strips until after the controller and all
other equipment in the panel near the module are mounted and wired.
Remove strips before operating the controller. Failure to remove strips
before operating can cause overheating.

• Electrostatic discharge can damage semiconductor devices inside the
module. Do not touch the connector pins or other sensitive areas.

• The USB and serial cables are not to exceed 3.0 m (9.84 ft).

• Do not wire more than 2 conductors on any single terminal.

Additional Resources

Resource Description

Micro830® and Micro850® Programmable
Controllers User Manual,
publication 2080-UM002

®

Micro800
Instructions, publication 2080-IN001

Micro800 Plug-in Modules User Manual,
publication 2080-UM004

Industrial Automation Wiring and
Grounding Guidelines, publication 1770-4.1

AC Power Supply Installation

A more detailed description of how to install and use your
Micro830 and Micro850 programmable controllers.

Information on installing and wiring the optional AC power supply.

Installation, wiring descriptions, and specifications, for the
different Micro800 plug-in modules.

More information on proper wiring and grounding techniques.

If you would like a manual, you can:

• download a free electronic version from the Internet:

http://literature.rockwellautomation.com

• purchase a printed manual by contacting your local Allen-Bradley distributor or
Rockwell Automation representative

Publication 2080-IN002B-EN-P - April 2014

Micro830 10 Point Programmable Controllers 7

12 3 4 5 6 7 8

79610111213

45030

Overview

The Micro830 10-point controller is an economical brick style controller with embedded inputs
and outputs. It can accommodate up to two plug-in modules and accommodates any 24V DC
output power supply that meets minimum specifications such as the optional Micro800 power
supply, 2080-PS120-240VAC.

Controller Overview

Controller Description

Description Description

1 Status indicators 8 Right-side cover

2 Optional power supply slot 9 DIN rail mounting latch

3 Plug-in module latch 10 Mode switch

4 Plug-in module screw hole 11 Type B connector USB port

5 40 pin high speed plug-in connector 12 RS232/RS485 non-isolated combo

6 I/O terminal block 13 Optional power supply

7 Mounting screw hole / mounting foot

serial port

Publication 2080-IN002B-EN-P - April 2014

8 Micro830 10 Point Programmable Controllers

Input status

Run status

Force status

Power status

Fault status

Output status

Serial communications

status

45031

45032

Mounting dimensions do not include mounting feet or DIN rail latches.

100 mm (3.94 in.)

80 mm (3.15 in.)

90 mm (3.54 in.)

Status Indicators

Mount the Module

Most applications require installation in an industrial enclosure to reduce the effects of electrical
interference and environmental exposure. Locate your controller as far as possible from power
lines, load lines, and other sources of electrical noise such as hard-contact switches, relays, and
AC motor drives. For more information on proper grounding guidelines, see the Industrial
Automation Wiring and Grounding Guidelines, publication 1770-4.1

Mounting Dimensions and DIN Rail Mounting

.

Module Spacing

Maintain spacing from objects such as enclosure walls, wireways and adjacent equipment. Allow

50.8 mm (2 in.) of space on all sides for adequate ventilation. An exception to this spacing
guideline is allowed for the side at which you are connecting the optional power supply,
2080-PS120-240VAC.

Publication 2080-IN002B-EN-P - April 2014

Micro830 10 Point Programmable Controllers 9

TIP

DIN Rail Mounting

The module can be mounted using the following DIN rails: 35 x 7.5 mm x 1 mm
(EN 50 022 - 35 x 7.5).

For environments with greater vibration and shock concerns, use the panel
mounting method, instead of DIN rail mounting.

Before mounting the module on a DIN rail, use a flat-blade screwdriver in the DIN rail latch and
pry it downwards until it is in the unlatched position.

1. Hook the top of the DIN rail mounting area of the controller onto the DIN rail, and
then press the bottom until the controller snaps onto the DIN rail.

2. Push the DIN rail latch back into the latched position.
Use DIN rail end anchors (Allen-Bradley part number 1492-EA35 or 1492-EAHJ35)
for vibration or shock environments.

To remove your controller from the DIN rail, pry the DIN rail latch downwards until it is in the
unlatched position.

Panel Mounting

The preferred mounting method is to use four M4 (#8) screws per module. Hole spacing
tolerance: ±0.4 mm (0.016 in.).

Follow these steps to install your controller using mounting screws.

1. Place the controller against the panel where you are mounting it. Make sure the
controller is spaced properly.

2. Mark drilling holes through the mounting screw holes and mounting feet then remove
the controller.

3. Drill the holes at the markings, then replace the controller and mount it.
Leave the protective debris strip in place until you are finished wiring the controller and
any other devices.

Publication 2080-IN002B-EN-P - April 2014

10 Micro830 10 Point Programmable Controllers

45325

86 mm (3.39 in.)

100 mm (3.94 in.)

Panel Mounting Dimensions

Use Surge Suppressors

Because of the potentially high current surges that occur when switching inductive load devices,
such as motor starters and solenoids, we recommend the use of some type of surge suppression to
protect and extend the operating life of the controllers output contacts. Switching inductive
loads without surge suppression can significantly reduce the life expectancy of relay contacts. By
adding a suppression device directly across the coil of an inductive device, you prolong the life of
the output or relay contacts. You also reduce the effects of voltage transients and electrical noise
from radiating into adjacent systems.

Refer to the Micro830/Micro850 Programmable Controllers User Manual, publication

2080-UM002

, for suitable surge suppression methods and recommended surge suppressors.

Publication 2080-IN002B-EN-P - April 2014

Wire the Controller

I-00

COM0 I-01

I-02

I-03

COM1

I-04

I-05 NC

NC

NC

NC

123456789101112

+DC24 CM0

O-00-DC24

CM1

O-01

CM2

O-02 O-03

CM3

NC

NC

123456789101112

45033

Input Terminal Block

Output Terminal Block

45034

Input Terminal Block

Output Terminal Block

2080-LC30-10QWB

2080-LC30-10QVB

Micro830 10 Point Programmable Controllers 11

COM0 I-01

I-03

I-04

123456789101112

I-00

+DC24 +CM0

I-02

O-01

COM1

I-05 NC

+CM1

123456789101112

O-00-DC24

-CM0

O-02 -CM1

NC

O-03

Publication 2080-IN002B-EN-P - April 2014

NC

NC

NC

NC

12 Micro830 10 Point Programmable Controllers

Hazardous Location
Class 1 Division 2,
Groups A, B, C, and D

Non-Hazardous Location

Micro800
Controller

USB Port

J3

V

max

= 5V DC

I

max

= 500 μA

L

i

= 1 μH

C

i

= 120 pF

Any associated apparatus with
Universal Serial Bus (USB) connection

USB Port

V

oc

, Isc, La and Ca to be determined per

Capacitance and Inductance Values
table

Capacitance and Inductance Values

Nonincendive

Equipment

Associated Apparatus

V

max

(or Ui) ≥ Voc or Vt (or Uo)

I

max

(or Li) ≥ Isc or It (or Io)

C

i

+ C

cable

≤ Ca (or Co)

Li + L

cable

≤ La (or Lo)

Capacitance and Inductance of the field wiring from the nonincendive equipment to the
associated apparatus shall be calculated and must be included in the system
calculations as shown in the table above.

Where the cable capacitance and inductance per foot are not known, the following
values shall be used: C

cable

= 60 pF/ft, L

cable

= 0.2 μH/ft.

Wiring method must be in accordance with ANSI/NFPA70.

Control Drawing for Class 1 Division 2 Applications

Publication 2080-IN002B-EN-P - April 2014

Micro830 10 Point Programmable Controllers 13

Min Max

Solid 0.14 mm

2

(26 AWG)

2.5 mm2
(14 AWG)

rated @ 90 °C
(194 °F ) insulation max

Stranded 0.14 mm2

(26 AWG)

1.5 mm2
(16 AWG)

Specifications

General Specifications

Attribute 2080-LC30-10QWB 2080-LC30-10QVB

Number of I/O 10 (6 inputs, 4 outputs)

Dimensions,
HxWxD

Shipping weight,
approx.

Wire size

Wiring category

Wire type Use Copper Conductors only

Terminal screw torque 0.6 Nm (4.4 lb-in) max

Input circuit type 12/24V sink/source (standard)

Output circuit type Relay 24V DC sink transistor (standard

Power consumption 5 W

Power supply
voltage range

I/O rating Input 24V DC, 8.8 mA

Isolation voltage 250V (continuous), Reinforced

Pilot duty rating C300, R150 N.A.

90 x 100 x 80 mm
(3.54 x 3.94 x 3.15 in.)

0.302 kg (0.666 lb)

(1)

2 – on signal ports
2 – on power ports

using a 2.5 mm (0.10 in.) flat-blade screwdriver.

24V sink/source (high-speed)

20.4…26.4V DC Class 2, or
Limited Voltage Limited Current Source (LVLC)

Output 2 A, 240 V AC, General Use

Insulation Type, Outputs to Aux
and Network, Inputs to Outputs
Type tested for 60 s @ 720 V DC,
Inputs to Aux and Network,
3250 V DC Outputs to Aux and
Network, Inputs to Outputs

and high-speed)

Input 24V DC, 8.8 mA
Output 2 A, 240 V DC, 1 A per point
(Surrounding air temperature 30 °C)
24 V DC, 0.3 A per point
(Surrounding air temperature 65 °C)

50V (continuous), Reinforced
Insulation Type, I/O to Aux and
Network, Inputs to Outputs
Type tested for 60 s @ 720 V DC,
I/O to Aux and Network, Inputs to
Outputs

Publication 2080-IN002B-EN-P - April 2014

14 Micro830 10 Point Programmable Controllers

General Specifications

Attribute 2080-LC30-10QWB 2080-LC30-10QVB

Insulation stripping

7 mm (0.28 in.)

length

Enclosure type rating Meets IP20

North American temp

T4

code

(1)

Use this Conductor Category information for planning conductor routing. Refer to Industrial Automation
Wiring and Grounding Guidelines, publication 1770-4.1

.

Input Specifications

Attribute High-speed DC input

(Inputs 0…3)

Standard DC input
(inputs 4 and higher)

Number of inputs 4 2

Input group to
backplane isolation

Verified by one of the following dielectric tests: 1,414V DC for 2 s
75V DC working voltage (IEC Class 2 reinforced insulation)

Voltage category 24V DC sink/source

Off-state voltage, max 5V DC

On-state voltage range 16.8…26.4V DC @ 65°C (149°F)

16.8…30.0V DC @ 30°C (86°F)

10…26.4V DC @ 65°C (149°F)
10…30.0V DC @ 30°C (86°F)

Off-state current, max 1.5 mA

On-state current, min 5.0 mA @ 16.8V DC 1.8 mA @ 10V DC

On-state current, nom 7.6 mA @ 24V DC 6.15 mA @ 24V DC

On-state current, max 12.0 mA @ 30V DC

Nominal impedance 3 kΩ 3.74 kΩ

IEC input compatibility Type 3

AC input filter setting 8 ms for all embedded inputs

In Connected Components Workbench, go to the Embedded I/O
configuration window to reconfigure the filter setting for each
input group.

Output Specifications

Attribute 2080-LC30-10QWB 2080-LC30-10QVB

Relay Output High-Speed Output

(Outputs 0…1)

Number of outputs 4 2 2

Publication 2080-IN002B-EN-P - April 2014

Standard Output
(Outputs 2…3)

Micro830 10 Point Programmable Controllers 15

Output Specifications

Attribute 2080-LC30-10QWB 2080-LC30-10QVB

Relay Output High-Speed Output

(Outputs 0…1)

Output voltage, min 5V DC, 5V AC 10.8V DC 10V DC

Output voltage, max 125V DC, 265V AC 26.4V DC 26.4V DC

Load current, min 10 mA 10 mA

Load current, max 2.0 A 100 mA (high-speed

operation)

1.0 A @ 30 °C

0.3 A @ 65 °C
(standard operation)

Surge current, per point See

Relay Contacts

Ratings on page 15

4.0 A for 10 ms every 1 s @ 30 °C;
every 2 s @ 65 °C

Current, per common, max 5 A 2 A 4 A

Current, per controller, max 1440V A 2 A 4 A

Turn on time/

10 ms 2.5 μs 0.1 ms

Turn off time, max

(1)

Applies for general purpose operation only. Does not apply for high-speed operation.

Standard Output
(Outputs 2…3)

1.0 A @ 30 °C

0.3 A @ 65 °C
(standard
operation)

(1)

1 ms

Relay Contacts Ratings

Maximum Volts Amperes Amperes

Make Break Make Break

Continuous

120V AC 15 A 1.5 A 2.0 A 1800V A 180V A

240V AC 7.5 A 0.75 A

24V DC 1.0 A 1.0 A 28V A

125V DC 0.22 A

Publication 2080-IN002B-EN-P - April 2014

Volt-Amperes

16 Micro830 10 Point Programmable Controllers

Environmental Specifications

Attribute Value

Temperature, operating IEC 60068-2-1 (Test Ad, Operating Cold),

Temperature, surrounding
air, max

Temperature,
non-operating

Relative humidity IEC 60068-2-30 (Test Db, Unpackaged Damp Heat):

Vibration IEC 60068-2-6 (Test Fc, Operating):

Shock, operating IEC 60068-2-27 (Test Ea, Unpackaged Shock):

Shock, non-operating IEC 60068-2-27 (Test Ea, Unpackaged Shock):

Emissions CISPR 11

ESD immunity IEC 61000-4-2:

Radiated RF immunity IEC 61000-4-3:

EFT/B immunity IEC 61000-4-4:

Surge transient immunity IEC 61000-4-5:

Conducted RF immunity IEC 61000-4-6:

IEC 60068-2-2 (Test Bd, Operating Dry Heat),
IEC 60068-2-14 (Test Nb, Operating Thermal Shock):

-20…65 °C (-4…149 °F)

65 °C (149 °F)

IEC 60068-2-1 (Test Ab, Unpackaged Nonoperating Cold),
IEC 60068-2-2 (Test Bb, Unpackaged Nonoperating Dry Heat),
IEC 60068-2-14 (Test Na, Unpackaged Nonoperating Thermal Shock):

-40…85 °C (-40…185 °F)

5…95% non-condensing

2 g @ 10…500 Hz

25 g

DIN mount: 25 g
PANEL mount: 45 g

Group 1, Class A

6 kV contact discharges
8 kV air discharges

10V/m with 1 kHz sine-wave 80% AM from 80…2000 MHz
10V/m with 200 Hz 50% Pulse 100% AM at 900 MHz
10V/m with 200 Hz 50% Pulse 100% AM at 1890 MHz
10V/m with 1 kHz sine-wave 80% AM from 2000…2700 MHz

±2 kV @ 5 kHz on power ports
±2 kV @ 5 kHz on signal ports

±1 kV line-line(DM) and ±2 kV line-earth(CM) on power ports
±1 kV line-line(DM) and ±2 kV line-earth(CM) on signal ports

10V rms with 1 kHz sine-wave 80% AM from 150 kHz…80 MHz

Publication 2080-IN002B-EN-P - April 2014

Certifications

Micro830 10 Point Programmable Controllers 17

Certification (when
product is marked)

Value

(1)

c-UL-us UL Listed Industrial Control Equipment, certified for US and Canada.

See UL File E322657.

UL Listed for Class I, Division 2 Group A,B,C,D Hazardous Locations,

certified for U.S. and Canada. See UL File E334470.

CE European Union 2004/108/EC EMC Directive, compliant with:

EN 61326-1; Meas./Control/Lab., Industrial Requirements
EN 61000-6-2; Industrial Immunity
EN 61000-6-4; Industrial Emissions
EN 61131-2; Programmable Controllers (Clause 8, Zone A & B)

European Union 2006/95/EC LVD, compliant with:

EN 61131-2; Programmable Controllers (Clause 11)

C-Tick Australian Radiocommunications Act, compliant with:

AS/NZS CISPR 11; Industrial Emissions

KC Korean Registration of Broadcasting and Communications Equipment,

compliant with:
Article 58-2 of Radio Waves Act, Clause 3

(1)

See the Product Certification link at http://www.rockwellautomation.com/products/certification for
Declaration of Conformity, Certificates, and other certification details.

Publication 2080-IN002B-EN-P - April 2014

18 Micro830 10 Point Programmable Controllers

Notes:

Publication 2080-IN002B-EN-P - April 2014

Notes:

Micro830 10 Point Programmable Controllers 19

Publication 2080-IN002B-EN-P - April 2014

Rockwell Automation Support

Rockwell Automation provides technical information on the Web to assist you in using its
products. At http://support.rockwellautomation.com, you can find technical manuals, a
knowledge base of FAQs, technical and application notes, sample code and links to software
service packs, and a MySupport feature that you can customize to make the best use of these
tools.

For an additional level of technical phone support for installation, configuration and
troubleshooting, we offer TechConnect support programs. For more information, contact your
local distributor or Rockwell Automation representative, or visit

ttp://support.rockwellautomation.com.

h

Installation Assistance

If you experience a problem within the first 24 hours of installation, please review the
information that's contained in this manual. You can also contact a special Customer Support
number for initial help in getting your product up and running.

United States 1.440.646.3434

Outside United
States

Monday – Friday, 8 a.m. – 5 p.m. EST

Please contact your local Rockwell Automation representative for any
technical support issues.

New Product Satisfaction Return

Rockwell Automation tests all of its products to ensure that they are fully operational when
shipped from the manufacturing facility. However, if your product is not functioning and needs
to be returned, follow these procedures.

United States Contact your distributor. You must provide a Customer Support case number

Outside United
States

Allen-Bradley, Rockwell Automation, Micro800 , Micro830 and TechConnect are trademarks of Rockwell Automation, Inc.

Trademarks not belonging to Rockwell Automation are property of their respective companies.

Publication 2080-IN002B-EN-P - April 2014 PN-244661

Supersedes Publication 2080-IN002A-EN-P - September 2010 Copyright © 2014 Rockwell Automation, Inc. All rights reserved. Printed in Singapore.

(call the phone number above to obtain one) to your distributor in order to
complete the return process.

Please contact your local Rockwell Automation representative for the return
procedure.