RISCO Group RK-308 User Manual

MINI – Passive

Infrared Detector

Installation Instructions

Model:

1

RK-308

Introduction

The MINI is a passive infrared detector that is simple to install with
an integrated wall bracket.

Preliminary Considerations

Choose the mounting location after careful consideration of the
protected area. The MINI should be located so that an intruder will
cross the infrared beam pattern at an angle closest to perpendicular.
Do not mount the unit in direct sunlight or near heat sources.

Front Cover Removal

Remove the front cover by twisting a flat screwdriver in the slot
between the cover and the base at the bottom of the MINI.

Mounting Procedure

Remove the desired knockouts in the MINI base for the mounting
screws and for cable entry. Insert the cable and attach the base to the
wall or corner.

Terminal Connections

Wire the cable to the terminal block at the bottom of the PC Board as
follows:

Terminal Purpose

12VDC Power supply inputs

ALARM N.C dry contacts

TAMPER N.C dry contacts

Seal the hole used for cable entry with suitable sealant.

2

PC Board Adjustment

Loosen the PC Board holding screw. Slide the PC Board so that the
plastic pointer on the left side is positioned at the appropriate scale
position as described below:

Scale Position Room Size

SHORT 3-6m (10-20 ft)

LONG 6-15m (20-43 ft)

RK 301 - WIDE ANGLE LENS: Typical mounting height: 2.5m (8.2
ft).

RK 307 - LONG RANGE LENS: Typical mounting height: 2.5 meters
(8.2 ft).Select scale position LONG.

RK 308 - CURTAIN LENS: Typical mounting height 2.5 m (8.2 ft)in
horizontal position (turn 90°). Select scale position LONG.

The detector logo on the cover should be in direction of the window
or door to be protected.

NOTE: For other mounting heights and for finer adjustment of
coverage:

• For higher than typical mounting heights:

Slide the PC Board up to reduce the effective range.

• For lower than typical mounting heights:

Slide the PC Board down to increase the effective range.

Tighten the holding screw to secure the PC Board.

Do a walk test as described below and readjust as necessary until a
desired coverage pattern is reached.

3

Jumper Settings

LED:
To disable the LED indication, remove the LED jumper and place it
on one pin only.
To enable the LED indication, place the LED jumper over both pins.

PULSE COUNT:
Set the PULSE COUNT JUMPER in position 1 or 3, corresponding to
the desired pulse count.
When using RK 307 or RK 308, always use a pulse count of 1.

Walk Test

Replace the front cover during the walk test. Apply power and wait
at least two minutes for the detector to stabilize. Walk through the
entire protected area and observe the LED to confirm full coverage.

MINI Range

Description: Range Order Code:

Wide Angle 15 m RK-301

Long Range 30 m RK-307

Curtain 12 m RK-308

Procedure for changing lenses

Release the lens by pressing on its two holding tabs. Slide the lens
out of the MINI cover. Reverse the procedure for inserting a new
lens.

4

Specifications

Operating Voltage: 9 to 16 VDC

Current: 15 mA at 12 volts

Alarm Contacts: 0.1 amps, 24 volts, N.C

Size: 6.5x4.4x3.5 cm (2.5x1.7x1.4 in.)

Optical Filtering: White light protection, pigmented lens

Operating Temperature: -10 to +50°C

Storage Temperature: -20 to +55°C

Lens Options

RK 301: WIDE ANGLE LENS RK 307: LONG RANGE LENS

5

RK 308: CURTAIN LENS

Standard Limited Product Warranty

RISCO Ltd., its subsidiaries and affiliates (“Risco") guarantee Risco’s hardware products to be
free from defects in materials and workmanship when used and stored under normal conditions
and in accordance with the instructions for use supplied by Risco, for a period of (i) 24 months
from the date of connection to the Risco Cloud (for cloud connected products) or (ii) 24 months
from production (for other products which are non-cloud connected), as the case may be (each,
the “Product Warranty Period” respectively).

Contact with customers only. This Product Warranty is solely for the benefit of the customer
who purchased the product directly from Risco, or from any authorized distributor of Risco.
Nothing in this Warranty obligates Risco to accept product returns directly from end users that
purchased the products for their own use from Risco’s customer or from any installer of Risco, or
otherwise provide warranty or other services to any such end user. Risco customer shall handle
all interactions with its end users in connection with the Warranty, inter alia regarding the
Warranty. Risco’s customer shall make no warranties, representations, guarantees or statements
to its customers or other third parties that suggest that Risco has any warranty or service
obligation to, or any contractual privy with, any recipient of a product.

Return Material Authorization. In the event that a material defect in a product shall be
discovered and reported during the Product Warranty Period, Risco shall, at its option, and at
customer's expense, either: (i) accept return of the defective Product and repair or have repaired
the defective Product, or (ii) accept return of the defective Product and provide a replacement
product to the customer. The customer must obtain a Return Material Authorization (“RMA”)
number from Risco prior to returning any Product to Risco. The returned product must be
accompanied with a detailed description of the defect discovered (“Defect Description”) and
must otherwise follow Risco’s then-current RMA procedure in connection with any such return.
If Risco determines in its reasonable discretion that any Product returned by customer conforms
to the applicable warranty (“Non-Defective Products”), Risco will notify the customer of such
determination and will return the applicable Product to customer at customer’s expense. In
addition, Risco may propose and assess customer a charge for testing and examination of Non­Defective Products.

Entire Liability. The repair or replacement of products in accordance with this warranty shall be
Risco’s entire liability and customer’s sole and exclusive remedy in case a material defect in a
product shall be discovered and reported as required herein. Risco’s obligation and the Warranty
are contingent upon the full payment by customer for such Product and upon a proven weekly
testing and examination of the product functionality.

6

Limitations. The Product Warranty is the only warranty made by Risco with respect to the
Products. The warranty is not transferable to any third party. To the maximum extent permitted
by applicable law, the Product Warranty does not apply and will be void if: (i) the conditions set
forth above are not met (including, but not limited to, full payment by customer for the product
and a proven weekly testing and examination of the product functionality); (ii) if the Products or
any part or component thereof: (a) have been subjected to improper operation or installation; (b)
have been subject to neglect, abuse, willful damage, abnormal working conditions, failure to
follow Risco’s instructions (whether oral or in writing); (c) have been misused, altered, modified
or repaired without Risco’s written approval or combined with, or installed on products, or
equipment of the customer or of any third party; (d) have been damaged by any factor beyond
Risco’s reasonable control such as, but not limited to, power failure, electric power surges, or
unsuitable third party components and the interaction of software therewith or (e) any delay or
other failure in performance of the product attributable to any means of communications,
provided by any third party service provider (including, but not limited to) GSM interruptions,
lack of or internet outage and/or telephony failure.

BATTERIES ARE EXPLICITLY EXCLUDED FROM THE WARRANTY AND RISCO SHALL NOT BE HELD
RESPONSIBLE OR LIABLE IN RELATION THERETO, AND THE ONLY WARRANTY APPLICABLE THERETO, IF
ANY, IS THE BATTERY MANUFACTURER'S WARRANTY.

Risco makes no other warranty, expressed or implied, and makes no warranty of merchantability or of
fitness for any particular purpose. For the sake of good order and avoidance of any doubt:

DISCLAIMER. EXCEPT FOR THE WARRANTIES SET FORTH HEREIN, RISCO AND ITS LICENSORS HEREBY
DISCLAIM ALL EXPRESS, IMPLIED OR STATUTORY, REPRESENTATIONS, WARRANTIES, GUARANTEES, AND
CONDITIONS WITH REGARD TO THE PRODUCTS, INCLUDING BUT NOT LIMITED TO ANY
REPRESENTATIONS, WARRANTIES, GUARANTEES, AND CONDITIONS OF MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE, TITLE AND LOSS OF DATA. WITHOUT LIMITING THE GENERALITY OF THE
FOREGOING, RISCO AND ITS LICENSORS DO NOT REPRESENT OR WARRANT THAT: (I) THE OPERATION OR
USE OF THE PRODUCT WILL BE TIMELY, SECURE, UNINTERRUPTED OR ERROR-FREE; (ii) THAT ANY FILES,
CONTENT OR INFORMATION OF ANY KIND THAT MAY BE ACCESSED THROUGH THE PRODUCT BY
CUSTOMER OR END USER SHALL REMAIN SECURED OR NON DAMAGED. CUSTOMER ACKNOWLEDGES
THAT NEITHER RISCO NOR ITS LICENSORS CONTROL THE TRANSFER OF DATA OVER COMMUNICATIONS
FACILITIES, INCLUDING THE INTERNET, GSM OR OTHER MEANS OF COMMUNICATIONS AND THAT
RISCO’S PRODUCTS, MAY BE SUBJECT TO LIMITATIONS, DELAYS, AND OTHER PROBLEMS INHERENT IN
THE USE OF SUCH MEANS OF COMMUNICATIONS. RISCO IS NOT RESPONSIBLE FOR ANY DELAYS,
DELIVERY FAILURES, OR OTHER DAMAGE RESULTING FROM SUCH PROBLEMS.

RISCO WARRANTS THAT ITS PRODUCTS DO NOT, TO THE BEST OF ITS KNOWLEDGE, INFRINGE UPON ANY
PATENT, COPYRIGHT, TRADEMARK, TRADE SECRET OR OTHER INTELLECTUAL PROPERTY RIGHT

IN ANY EVENT RISCO SHALL NOT BE LIABLE FOR ANY AMOUNTS REPRESENTING LOST REVENUES OR
PROFITS, PUNITIVE DAMAGES, OR FOR ANY OTHER INDIRECT, SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES, EVEN IF THEY WERE FORESEEABLE OR RISCO HAS BEEN INFORMED OF
THEIR POTENTIAL.

Risco does not install or integrate the product in the end user security system and is therefore not
responsible for and cannot guarantee the performance of the end user security system which uses
the product.

7

Risco does not guarantee that the product will prevent any personal injury or property loss by
burglary, robbery, fire or otherwise; or that the product will in all cases provide adequate
warning or protection.

Customer understands that a correctly installed and maintained alarm may only reduce the risk
of burglary, robbery or fire without warning, but is not an assurance or a guarantee that such an
event will not occur or that there will be no personal injury or property loss as a result thereof.
Consequently Risco shall have no liability for any personal injury, property damage or loss based
on a claim that the product fails to give warning.
No employee or representative of Risco is authorized to change this warranty in any way or grant
any other warranty.

RTTE Compliance Statement:

Hereby, RISCO Group declares that this equipment is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC. For the CE Declaration
of Conformity please refer to our website: www.riscogroup.com.

Contacting RISCO Group

RISCO Group is committed to customer service and product support. You can contact us
through our website (www.riscogroup.com) or at the following telephone and fax numbers:

United Kingdom

Tel: [phone]
[e-mail]

Italy

Tel: [phone]
[e-mail]

Spain

Tel: [phone]
[e-mail]

France

Tel: [phone]
[e-mail]

All rights reserved.

No part of this document may be reproduced in any form without prior written permission
from the publisher.

© RISCO Group 01/2015 5IN2408

8

Belgium (Benelux)

Tel: [phone]
[e-mail]

USA

Tel: [phone]
[e-mail]

Brazil

Tel: [phone]
[e-mail]

China (Shanghai)

Tel: [phone]
[e-mail]

China (Shenzhen)

Tel: [phone]
[e-mail]

Poland

Tel: [phone]
[e-mail]

Israel

Tel: [phone]
[e-mail]

Australia

Tel: + 1800-991-542
[e-mail]