BA178M!!T / BA178M!!FP series
Regulator ICs
BA178M!!T / BA178M!!FP series
The BA178M!!T and BA178M!!FP series are 3-pin, fixed positive output voltage regulators. These regulators are used to provide a stabilized output voltage from a fluctuating DC input voltage.
There are 11 fixed output voltages, as follows : 5V, 6V, 7V, 8V, 9V, 10V, 12V, 15V, 18V, 20V, and 24V. The maximum current capacity is 0.5A for each of the above voltages.
"Application
Constant voltage power supply
"Features
1)Built-in overcurrent protection circuit and thermal shutdown circuit.
2)Excellent ripple regulation.
3)Available in TO-220FP and TO252-3 packages, to meet wide range of applications.
4)Compatible with other manufacturers' regulators.
5)Richly diverse lineup. (5V, 6V, 7V, 8V, 9V, 10V, 12V, 15V, 18V, 20V, 24 V)
"Product codes
Output voltage (V) |
Product No. |
Output voltage (V) |
Product No. |
|
|
|
|
5 |
BA178M05T / FP |
12 |
BA178M12T / FP |
|
|
|
|
6 |
BA178M06T / FP |
15 |
BA178M15T / FP |
|
|
|
|
7 |
BA178M07T / FP |
18 |
BA178M18T / FP |
|
|
|
|
8 |
BA178M08T / FP |
20 |
BA178M20T / FP |
|
|
|
|
9 |
BA178M09T / FP |
24 |
BA178M24T / FP |
|
|
|
|
10 |
BA178M10T / FP |
− |
− |
|
|
|
|
BA178M!!T / BA178M!!FP series
Regulator ICs
"Internal circuit configuration diagram
(1)
INPUT
R4 |
R10 |
|
R8 |
R9 |
R13 |
|
|
|
|
|
|
Q8 |
|
|
|
|
|
Q12 |
|
|
|
Q9 |
D2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Q16 |
|
|
|
|
|
|
Q15 |
|
Q17 |
|
|
|
|
|
|
R21 |
R12 |
|
|
R5 |
Q13 |
|
|
|
R17 |
R11 |
|
|
|
|
Q10 |
|
(3) |
||||
|
|
|
|
|||||
|
|
|
|
Q6 |
|
|
|
OUTPUT |
|
|
|
|
|
|
|
|
|
R6 |
|
|
|
|
|
|
|
|
|
|
|
Q5 |
|
|
|
|
|
|
|
|
|
R15 |
|
|
|
|
|
|
R1 |
R2 |
R16 |
|
|
R20 |
|
|
|
C1 |
Q11 |
|
|
|
||
D1 |
|
|
|
|
|
|
|
|
Q18 |
|
Q7 |
|
|
|
|
|
|
|
|
|
Q2 |
Q4 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Q14 |
Q1 |
|
Q3 |
|
|
R19 |
|
|
|
|
|
R14 |
|
|
|
|
|
|
|
|
|
|
|
|
|
R7 |
R22 |
|
R10 |
R3 |
|
|
|
|
|
|
|
|
D3 |
|
|
|
(2) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
COMMON |
"Absolute maximum ratings (Ta=25°C)
^Common specifications for BA178M!!T / FP seriesp
Parameter |
Symbol |
Limits |
Unit |
||
|
|
|
|
||
Applied voltage |
VIN |
35 |
V |
||
|
|
|
|
|
|
Power dissipation |
TO220FP |
Pd |
2.0 |
W |
|
TO252−3 |
1.0 |
||||
|
|
|
|||
Operating temperature |
Topr |
−40~+85 |
°C |
||
|
|
|
|
||
Storage temperature |
Tstg |
−55~+150 |
°C |
||
|
|
|
|
|
Reduced by 16 mW (TO220FP) and 8 mW (TO252-3) for each increase in Ta of 1°C over 25°C (without heat sink).
"Recommended operating conditions (Ta=25°C) BA178M05T / FP
Parameter |
Symbol |
Min. |
Typ. |
Max. |
Unit |
|
|
|
|
|
|
Input voltage |
VIN |
7.5 |
− |
20 |
V |
|
|
|
|
|
|
Output current |
IO |
− |
− |
0.5 |
A |
|
|
|
|
|
|
BA178M06T / FP
Parameter |
Symbol |
Min. |
Typ. |
Max. |
Unit |
|
|
|
|
|
|
Input voltage |
VIN |
8.5 |
− |
21 |
V |
|
|
|
|
|
|
Output current |
IO |
− |
− |
0.5 |
A |
|
|
|
|
|
|
BA178M07T / FP
Parameter |
Symbol |
Min. |
Typ. |
Max. |
Unit |
|
|
|
|
|
|
Input voltage |
VIN |
9.5 |
− |
22 |
V |
|
|
|
|
|
|
Output current |
IO |
− |
− |
0.5 |
A |
BA178M09T / FP
Parameter |
Symbol |
Min. |
Typ. |
Max. |
Unit |
|
|
|
|
|
|
Input voltage |
VIN |
11.5 |
− |
24 |
V |
|
|
|
|
|
|
Output current |
IO |
− |
− |
0.5 |
A |
|
|
|
|
|
|
BA178M08T / FP
Parameter |
Symbol |
Min. |
Typ. |
Max. |
Unit |
|
|
|
|
|
|
Input voltage |
VIN |
10.5 |
− |
23 |
V |
|
|
|
|
|
|
Output current |
IO |
− |
− |
0.5 |
A |
|
|
|
|
|
|
BA178M10T / FP
Parameter |
Symbol |
Min. |
Typ. |
Max. |
Unit |
|
|
|
|
|
|
Input voltage |
VIN |
12.5 |
− |
25 |
V |
|
|
|
|
|
|
Output current |
IO |
− |
− |
0.5 |
A |
BA178M!!T / BA178M!!FP series
Regulator ICs
BA178M12T / FP
Parameter |
Symbol |
Min. |
Typ. |
Max. |
Unit |
|
|
|
|
|
|
Input voltage |
VIN |
15 |
− |
27 |
V |
|
|
|
|
|
|
Output current |
IO |
− |
− |
0.5 |
A |
BA178M15T / FP
Parameter |
Symbol |
Min. |
Typ. |
Max. |
Unit |
|
|
|
|
|
|
Input voltage |
VIN |
17.5 |
− |
30 |
V |
|
|
|
|
|
|
Output current |
IO |
− |
− |
0.5 |
A |
|
|
|
|
|
|
BA178M18T / FP
Parameter |
Symbol |
Min. |
Typ. |
Max. |
Unit |
|
|
|
|
|
|
Input voltage |
VIN |
21 |
− |
33 |
V |
|
|
|
|
|
|
Output current |
IO |
− |
− |
0.5 |
A |
|
|
|
|
|
|
BA178M20T / FP
Parameter |
Symbol |
Min. |
Typ. |
Max. |
Unit |
|
|
|
|
|
|
Input voltage |
VIN |
23 |
− |
33 |
V |
|
|
|
|
|
|
Output current |
IO |
− |
− |
0.5 |
A |
|
|
|
|
|
|
BA178M24T / FP
Parameter |
Symbol |
Min. |
Typ. |
Max. |
Unit |
|
|
|
|
|
|
Input voltage |
VIN |
27 |
− |
33 |
V |
|
|
|
|
|
|
Output current |
IO |
− |
− |
0.5 |
A |
|
|
|
|
|
|
"Electrical characteristics
<BA178M05T / FP individual specifications> (unless otherwise noted, Ta=25°C, VIN=10V, IO=350mA)
Parameter |
Symbol |
Min. |
Typ. |
Max. |
Unit |
Conditions |
Measurement |
|
circuit |
||||||||
|
|
|
|
|
|
|
||
Output voltage 1 |
VO1 |
4.8 |
5.0 |
5.2 |
V |
IO=350mA |
Fig.1 |
|
|
|
|
|
|
|
|
|
|
Output voltage 2 |
VO2 |
4.75 |
− |
5.25 |
V |
VIN=7.5~20V, IO=5~350mA |
Fig.1 |
|
|
|
|
|
|
|
|
|
|
Input stability 1 |
Reg.I1 |
− |
3 |
100 |
mV |
VIN=7~25V, IO=200mA |
Fig.1 |
|
|
|
|
|
|
|
|
|
|
Input stability 2 |
Reg.I2 |
− |
1 |
50 |
mV |
VIN=8~12V, IO=200mA |
Fig.1 |
|
|
|
|
|
|
|
|
|
|
Ripple rejection ratio |
R.R. |
62 |
78 |
− |
dB |
eIN=1Vrms, f=120Hz, IO=100mA |
Fig.2 |
|
|
|
|
|
|
|
|
|
|
Load regulation 1 |
Reg.L1 |
− |
20 |
100 |
mV |
IO=5~500mA |
Fig.1 |
|
|
|
|
|
|
|
|
|
|
Load regulation 2 |
Reg.L2 |
− |
10 |
50 |
mV |
IO=5~200mA |
Fig.1 |
|
|
|
|
|
|
|
|
|
|
Temperature coefficient of output voltage |
TCVO |
− |
−1.0 |
− |
mV/°C |
IO=5mA, Tj=0~125°C |
Fig.1 |
|
|
|
|
|
|
|
|
|
|
Output noise voltage |
Vn |
− |
40 |
− |
µV |
f=10Hz~100kHz |
Fig.3 |
|
|
|
|
|
|
|
|
|
|
Minimum I/O voltage differential |
Vd |
− |
2.0 |
− |
V |
IO=500mA |
Fig.4 |
|
|
|
|
|
|
|
|
|
|
Bias current |
Ib |
− |
4.5 |
6.0 |
mA |
IO=0mA |
Fig.5 |
|
|
|
|
|
|
|
|
|
|
Bias current change 1 |
Ib1 |
− |
− |
0.5 |
mA |
IO=5~350mA |
Fig.5 |
|
|
|
|
|
|
|
|
|
|
Bias current change 2 |
Ib2 |
− |
− |
0.8 |
mA |
VIN=8~25V, IO=200mA |
Fig.5 |
|
|
|
|
|
|
|
|
|
|
Peak output current |
IO−P |
− |
875 |
− |
mA |
Tj=25°C |
Fig.1 |
|
|
|
|
|
|
|
|
|
|
Output short-circuit current |
IOS |
− |
0.4 |
− |
A |
VIN=25V |
Fig.6 |
|
|
|
|
|
|
|
|
|
BA178M!!T / BA178M!!FP series
Regulator ICs
<BA178M06T / FP individual specifications> (unless otherwise noted, Ta=25°C, VIN=11V, IO=350mA)
Parameter |
Symbol |
Min. |
Typ. |
Max. |
Unit |
Conditions |
Measurement |
|
circuit |
||||||||
|
|
|
|
|
|
|
||
Output voltage 1 |
VO1 |
5.75 |
6.0 |
6.25 |
V |
IO=350mA |
Fig.1 |
|
|
|
|
|
|
|
|
|
|
Output voltage 2 |
VO2 |
5.7 |
− |
6.3 |
V |
VIN=8.5~21V, IO=5~350mA |
Fig.1 |
|
|
|
|
|
|
|
|
|
|
Input stability 1 |
Reg.I1 |
− |
3 |
100 |
mV |
VIN=8~25V, IO=200mA |
Fig.1 |
|
|
|
|
|
|
|
|
|
|
Input stability 2 |
Reg.I2 |
− |
1 |
50 |
mV |
VIN=9~25V, IO=200mA |
Fig.1 |
|
|
|
|
|
|
|
|
|
|
Ripple rejection ratio |
R.R. |
60 |
74 |
− |
dB |
eIN=1Vrms, f=120Hz, IO=100mA |
Fig.2 |
|
|
|
|
|
|
|
|
|
|
Load regulation 1 |
Reg.L1 |
− |
20 |
120 |
mV |
IO=5~500mA |
Fig.1 |
|
|
|
|
|
|
|
|
|
|
Load regulation 2 |
Reg.L2 |
− |
10 |
60 |
mV |
IO=5~200mA |
Fig.1 |
|
|
|
|
|
|
|
|
|
|
Temperature coefficient of output voltage |
TCVO |
− |
−0.5 |
− |
mV/°C |
IO=5mA, Tj=0~125°C |
Fig.1 |
|
|
|
|
|
|
|
|
|
|
Output noise voltage |
Vn |
− |
60 |
− |
µV |
f=10Hz~100kHz |
Fig.3 |
|
|
|
|
|
|
|
|
|
|
Minimum I/O voltage differential |
Vd |
− |
2.0 |
− |
V |
IO=500mA |
Fig.4 |
|
|
|
|
|
|
|
|
|
|
Bias current |
Ib |
− |
4.5 |
6.0 |
mA |
IO=0mA |
Fig.5 |
|
|
|
|
|
|
|
|
|
|
Bias current change 1 |
Ib1 |
− |
− |
0.5 |
mA |
IO=5~350mA |
Fig.5 |
|
|
|
|
|
|
|
|
|
|
Bias current change 2 |
Ib2 |
− |
− |
0.8 |
mA |
VIN=9~25V, IO=200mA |
Fig.5 |
|
|
|
|
|
|
|
|
|
|
Peak output current |
IO−P |
− |
875 |
− |
mA |
Tj=25°C |
Fig.1 |
|
|
|
|
|
|
|
|
|
|
Output short-circuit current |
IOS |
− |
0.4 |
− |
A |
VIN=25V |
Fig.6 |
|
|
|
|
|
|
|
|
|
<BA178M07T / FP individual specifications> (unless otherwise noted, Ta=25°C, VIN=13V, IO=350mA)
Parameter |
Symbol |
Min. |
Typ. |
Max. |
Unit |
Conditions |
Measurement |
|
circuit |
||||||||
|
|
|
|
|
|
|
||
Output voltage 1 |
VO1 |
6.7 |
7.0 |
7.3 |
V |
IO=350mA |
Fig.1 |
|
|
|
|
|
|
|
|
|
|
Output voltage 2 |
VO2 |
6.65 |
− |
7.35 |
V |
VIN=9.5~22V, IO=5~350mA |
Fig.1 |
|
|
|
|
|
|
|
|
|
|
Input stability 1 |
Reg.I1 |
− |
4 |
100 |
mV |
VIN=9~25V, IO=200mA |
Fig.1 |
|
|
|
|
|
|
|
|
|
|
Input stability 2 |
Reg.I2 |
− |
1 |
50 |
mV |
VIN=10~25V, IO=200mA |
Fig.1 |
|
|
|
|
|
|
|
|
|
|
Ripple rejection ratio |
R.R. |
57 |
71 |
− |
dB |
eIN=1Vrms, f=120Hz, IO=100mA |
Fig.2 |
|
|
|
|
|
|
|
|
|
|
Load regulation 1 |
Reg.L1 |
− |
20 |
140 |
mV |
IO=5~500mA |
Fig.1 |
|
|
|
|
|
|
|
|
|
|
Load regulation 2 |
Reg.L2 |
− |
10 |
70 |
mV |
IO=5~200mA |
Fig.1 |
|
|
|
|
|
|
|
|
|
|
Temperature coefficient of output voltage |
TCVO |
− |
−0.5 |
− |
mV/°C |
IO=5mA, Tj=0~125°C |
Fig.1 |
|
|
|
|
|
|
|
|
|
|
Output noise voltage |
Vn |
− |
70 |
− |
µV |
f=10Hz~100kHz |
Fig.3 |
|
|
|
|
|
|
|
|
|
|
Minimum I/O voltage differential |
Vd |
− |
2.0 |
− |
V |
IO=500mA |
Fig.4 |
|
|
|
|
|
|
|
|
|
|
Bias current |
Ib |
− |
4.5 |
6.0 |
mA |
IO=0mA |
Fig.5 |
|
|
|
|
|
|
|
|
|
|
Bias current change 1 |
Ib1 |
− |
− |
0.5 |
mA |
IO=5~350mA |
Fig.5 |
|
|
|
|
|
|
|
|
|
|
Bias current change 2 |
Ib2 |
− |
− |
0.8 |
mA |
VIN=10~25V, IO=200mA |
Fig.5 |
|
|
|
|
|
|
|
|
|
|
Peak output current |
IO−P |
− |
875 |
− |
mA |
Tj=25°C |
Fig.1 |
|
|
|
|
|
|
|
|
|
|
Output short-circuit current |
IOS |
− |
0.4 |
− |
A |
VIN=25V |
Fig.6 |
|
|
|
|
|
|
|
|
|