Size:
2.04 Mb
Download

Setting up your DVD/CD Receiver

When connecting this system or changing connections, be sure to switch the power off with the STANDBY/ON button, and disconnect the power cord from the AC outlet. Do not use these speakers with any other system or amplifier as this may result in damage or fire.

Check that you have all the accessories, then put

1 the batteries in the remote control.

 

 

Batteries and

 

remote control

Power cord

 

STANDBY/ON

DVD

TUNER

TV LINE

 

CD

FM/AM

L1/L2

 

FRONT

 

 

 

SURROUND

OPEN CLOSE

 

 

8

0

 

1 3

¡

 

4

7

4

 

 

 

 

DVD MENU

RETURN

 

 

TUNE+

 

 

 

ST–

ST+

 

 

ENTER

 

 

MUTE

TUNE–

SOUND

Video cord

 

VOLUME

 

 

MASTER

 

 

TV CONTROL

 

CH

INPUT

VOL

OPEN

FM antenna

AM loop antenna

1

2

3

2 Connect the AM and FM antennas to the rear panel of the DVD/CD receiver.

1Pull off the protective shields of both AM antenna wires.

2Push open the tabs, then insert

one wire fully into each terminal.

6

3 Release the tabs to secure the AM antenna wires.

fig. A

fig. B

fig. C

4

4Fix the AM loop antenna to the attached stand.

To fix the stand to the antenna, bend in the direction indicated by the arrow (fig. A) then clip the loop onto the stand (fig. B).

Note: If you plan to mount the AM antenna to a wall or other surface, secure the stand with screws (fig. C) before clipping the loop to the stand. Make sure the reception is clear.

ANTENNA FM

AM

UNBAL 75

LOOP ANTENNA

1 2

3

5 Place the AM antenna on a flat

6 Connect the FM wire antenna to the FM UNBAL 75antenna terminal.

surface and point in the direction

For best results, extend the FM antenna fully and fix to a wall or door

giving the best reception.

frame. Don’t drape loosely or leave coiled up.

Don’t let it come into contact with metal

Note: The signal earth (H) is designed to reduce noise that occurs when an

objects and avoid placing near computers,

antenna is connected. It is not an electrical safety earth.

television sets or other electrical appliances.

 

3 Connect each speaker using the color-coded speaker cords. Match them to the colored labels above the speaker terminals.

Surround right

Surround left

(Grey)

(Blue)

 

 

IN

IN

OUT

FRONT

CENTER

SURROUND

 

L

SPEAKERS

6

6

 

Listening position

6

 

 

L

 

L

 

R

 

 

 

 

R

 

TV AUDIO

LINE 1

 

R

 

Subwoofer (Purple)

6

6

6

 

 

 

 

SUB

 

 

 

 

WOOFER

 

 

 

 

Center (Green)

Front right

Front left

(Red)

(White)

For the best surround sound, setup your speakers as above. The front left and right speakers should be about 1.8–2.7 m apart.

Connect each speaker as shown below.

Color-coded wire

(Connect to speaker)

Color-coded connector (Connect to rear panel)

1

Twist and pull off the protective

 

shields on each wire.

2

Connect the wires to the

 

speaker. Match the colored

 

wire with the color-coded

 

label (above the tabs), then

 

insert the colored wire into

 

the red (+) tab and the other

 

wire with the black (–) tab.

3

Connect the other end to the

color-coded speaker jacks on the rear of the DVD/CD receiver (as shown at left). Make sure to insert completely.

These speaker terminals can be hazardous when live. When you connect or disconnect the speaker cables, to prevent the risk of electric shock, do not touch uninsulated parts before disconnecting the power cord.

Using the remote control

Additional notes on connecting antennas

The remote control can be used within a range of about 7 meters from the remote sensor on the front panel, and within a 30 degree angle.

Precautions:

The remote control may not work if there is an obstacle between the remote control and the display unit, or if the remote control is not directed towards the remote sensor of the display unit at the correct angle.

The remote control may not work properly if strong light such as direct sunlight or fluorescent light is shining onto the unit’s remote sensor.

The remote control may not work properly when this unit is used near devices emitting infrared rays, or when remote controls of other devices which use infrared rays are used. Also, the use of this remote control may cause other devices to work improperly.

When the operating range of the remote becomes too short, replace the batteries.

Remote control battery caution

Incorrect use of batteries may cause leakage or rupture.

Always be sure to follow these guidelines:

Always insert batteries into the battery compartment correctly matching the positive ª and negative · polarities, as shown by the display inside the compartment.

Never mix new and used batteries.

Batteries of the same size may have different voltages, depending on brand. Do not mix different brands of batteries.

When disposing of used batteries, please comply with governmental regulations or environmental public instruction's rules that apply in your country or area.

In order to prevent battery leakage, remove the batteries when not using the remote control for an extended period (one month or more). If leakage occurs, carefully wipe away any battery fluid inside the compartment, and replace the batteries with new ones.

Do not allow books or other objects to rest on top of the remote control, since the buttons may be depressed, causing faster exhaustion of the batteries.

Keep antenna cables away from other cables and the display unit and main set.

To assure optimum reception, pull the FM antenna so that it is fully extended and not coiled or hanging at the rear of the unit.

If reception with the supplied antenna is poor, see the Other Connections section in the main operating instructions for details on connecting outdoor antennas.

Additional notes on speaker placement

If your listening room is of adequate size, place the speakers as shown in step 3 to achieve the optimum surround sound effect. If you are listening in a fairly small room and a typical surround speaker setup is not possible, see Home Theater sound setup of the instruction manual and the speaker setup guide for information on the Front Surround speaker setup option.

When using the standard speaker setup as shown in step 3, please observe the following guidelines:

Install the main front left and right speakers at an equal distance from the TV.

For optimum effect, install the rear speakers slightly above ear level.

Install the center speaker above or below the TV so that the sound of the center channel is localized at the TV screen.

Precautions:

When installing the center speaker on top of the TV, be sure to secure it with tape or some other suitable means. Otherwise, the speaker may fall from the TV due to external shocks such as earthquakes, endangering those nearby or damaging the speaker.

Do not connect the supplied speakers with any other amplifier. This may result in malfunction or fire.

The front, center and surround speakers supplied with this system are magnetically shielded. However, placing them extremely close to a television may result in color distortion on the screen. If this happens, move the speakers a little further away and switch off the television for 15-30 minutes.

The subwoofer is not magnetically shielded and so should not be placed near a TV or monitor.

Since it is not magnetically shielded, do not place any magnetic storage media (such as floppy disks and tape or video cassettes) close to the subwoofer.

4 Connect the DVD/CD receiver to your TV, then connect the supplied power cord.

1Connect one end to a video input on your TV.

Use the supplied video cord.

2Connect the other end to the video output of the DVD/CD receiver.

This player is equipped with copy protection technology. Do not connect this player to your TV via a VCR using AV cables, as the picture from this player will not appear properly on your TV.

3Connect the power cord to the AC inlet.

VIDEO IN

 

 

IN

IN

 

 

6

6

6

L

 

 

L

 

L

LINE 2

 

 

 

R

 

 

 

 

TV

LINE 1

 

 

R

 

R

 

 

 

6

6

6

Y

P

P

VIDEO

OUT

VIDEO

AC IN

To AC outlet

Congratulations! You're done setting up.

Printed in

<XRE3085-A>