C2945M-D (6/08)
C10DN Series Camera
Quick Start Guide
This quick start guide describes how to install and configure the C10DN Series camera in most applications. It contains a representation of the setup menus to help you locate and change specific settings.
Refer to the enclosed CD for the following documentation:
•Installation/Operation manual: C2944M
•Quick Start Guide: C2945M
•Important Safety Instructions: SAFETY.PDF
C10DN-6 1/3-inch high resolution day/night, CCD camera, 24 VAC or 12 VDC, NTSC format
C10DN-6X 1/3-inch high resolution day/night, CCD camera, 24 VAC or 12 VDC, PAL format
C10DN-7X 1/3-inch high resolution day/night, CCD camera, 220 to 240 VAC, PAL format
C10DN-7X BACK
ì Camera Mount |
r Ground Screw |
|
î Back Focus Locking Screw |
s Power Connector |
|
ï Lens Mount |
• C10DN-6/6X, Power Terminal Block |
|
• C10DN-7X, Power Cord |
||
ñ Auto Iris Lens Connector |
||
t Video Output Connector |
||
ó Setup Button |
||
|
The camera default settings are set at the factory to operate in most applications and lighting conditions, and normally require no adjustments. Sometimes, however, adjustments may be necessary.
Use the setup menus to customize the camera settings for your application as needed. Refer to the Installation/Operation manual (C2946M) for complete instructions and explanations of camera settings.
MAIN MENU
PROFILES |
-> |
EXPOSURE SET. |
-> |
FUNCTION SET. |
-> |
SAVE AS CUSTOM |
-> |
PIXEL CORRECTION |
-> |
SYSTEM INFORMATION |
-> |
PROFILES
STANDARD
DAY&NIGHT
GAMING
CUSTOM
BACK EXIT
|
|
EXPOSURE SET. |
|
|
ECLIPSER |
|
EXIT |
AUTO EXPOSURE |
-> ESC |
ECLIPSER |
|
-> OFF |
|
ECLIPSER |
|
-> OFF |
THRESHOLD |
-> 17 |
||
|
|
|||||
|
DC IRIS LEVEL |
-> -8 |
LEVEL |
|
-> 4 |
|
|
FLICKERLESS |
-> OFF |
|
|
|
|
|
AGC |
|
-> LOW |
BACK |
EXIT |
|
|
DAY&NIGHT |
-> AUTO |
|
|
|
|
|
DETECT TIME |
-> 5SEC |
|
|
|
|
|
FILTER LIMIT |
-> OFF |
|
|
|
|
|
BACK |
EXIT |
|
|
|
|
|
FUNCTION SET. |
|
|
LINE SYNC |
|
LINE SYNC |
-> AUTO |
LINE SYNC |
-> AUTO |
||
WHITE BALANCE |
-> AUTO |
V-PHASE ADJ |
-> 38 |
||
CHROMA |
-> |
|
|
|
|
GAMMA |
-> 60% |
BACK |
EXIT |
|
|
SHARPNESS |
-> SHARP |
|
|
|
|
CABLE COMPENSATION |
-> SHORT |
|
|
|
|
MASKING |
-> |
|
|
|
|
TITLE |
|
-> |
|
|
|
BACK |
EXIT |
|
|
|
MASKING |
|
|
|
MASK |
-> OFF |
|
|
|
|
MASK COLOR |
-> -2 |
|
|
|
|
MASK EDIT |
-> 0 |
|
|
SAVE AS CUSTOM |
MASK ERASE |
|
||
|
BACK |
EXIT |
|
||
CURRENT SETTING |
|
|
|||
|
|
|
|
||
ARE SAVED |
|
|
|
|
|
OK |
CANCEL |
|
|
|
|
|
|
|
|
|
TITLE |
|
|
|
TITLE |
|
-> OFF |
|
PIXEL CORRECTION |
EDIT TITLE |
|
||
|
BACK |
EXIT |
|
||
COVER THE LENS |
|
|
|||
|
|
|
|
||
AND PRESS OK |
|
|
|
|
|
OK |
CANCEL |
|
|
|
|
|
SYSTEM INFORMATION |
|
RESTORE FACTORY SETTING |
||
FIRMWARE VERSION |
#.## |
ALL SETTING ARE |
|||
OSD VERSION |
#.## |
INITIALIZED |
|
||
RESTORE FACTORY SETTINGS -> |
OK |
CANCEL |
|
||
BACK |
EXIT |
|
|
|
|
Use the 5-position button controller on the side panel of the camera to access and navigate the on-screen display (OSD) menus. Use the following table to navigate through the menu options.
Menu Options |
Navigating the Menu |
|
|
|
|
Display the MAIN MENU on the screen. |
Press and hold down the center button for two |
|
seconds. |
||
|
||
|
|
|
Move the cursor up or down in a menu or toggle |
Move the button up or down. |
|
through menu selections. |
||
|
||
|
|
|
Move the cursor right or left in a menu. |
Move the button left or right. |
|
|
|
|
Select a menu or make a menu selection. |
Press the center button. |
|
|
|
|
Save a setting and then return to the menu. |
Press the center button. |
|
|
|
The C10DN Series camera supports both manual and auto iris lenses, either fixed focal length or varifocal. It automatically senses an auto iris lens as soon as you plug in the connector.
The camera has a standard CS mount that can accept a C mount lens with a PCMA40 lens adapter.
To mount the lens onto the camera:
1.Make sure the lens does not touch the camera imager when installed.
2.Use clean, compressed air or a clean, dry lens cloth to make sure there is no dust or other foreign matter between the lens and the camera imager.
3.C mount lens: Screw the adapter onto the lens.
4.Screw the lens onto the lens mount.
5.Auto iris lens: Connect the 4-pin connector from the lens to the connector on the side of the camera.
6.Perform the lens focusing procedure before using the lens (refer to Lens Focus).